Search Documents

By M. E. Fine

IN the apparatus for measuring internal friction shown in fig. 1, a modification of that described by Kê,1,2 the parasitic energy loss or background is equivalent to a Q-1 of approximately 4x10-5. This low value of background was obtained by using a jeweler's collet of appropriate size for the upper support, eliminating lateral motion without immersing the bob in oil, and designing the bob to reduce air resistance. The pendulum is supported on the frame through a snug fitting, sliding rotary joint (fig. I-B). A slight twist of the top imparts essentially pure torsional motion to the pendulum. No evidence of energy loss in the sliding joint has been observed. In the bob (E) steel balls are used in the torsion arm, and the bottom is filled with lead giving a total weight of 94 g. A lighter bob may be used for small diameter specimens. Another bob was a solid disc with provision for adding discs to change the frequency. The oscillating image of the filament is recorded on a revolving drum camera (fig. 1-3) driven by a synchronous motor. This allows use of frequencies higher than can be measured visually on a glass scale. Samples varying in diameter from 0.020 to 0.075 in. have been measured, the frequencies have ranged from 1 to 12 cps, and the maximum strain varied from 0.5 to 10x10-5. With appropriate modification the sample may be placed in a thermostat. The apparatus may also be used to measure the shear modulus. In the examples of measurement given in table I the internal friction of Permendur and the 46.8 Ni-Fe alloy are due, for the most part, to magneto-mechanical hysteresis8 (elastic hysteresis accompanying stress-induced magnetostriction) which depends on strain amplitude and increases with annealing. The internal friction of most materials decreases with annealing. References IT. S. K6: Physics Review (1947) 71, 533. 2 T. S. Kê: Transactions AIME (1948) 176, 448; Metals Technology (June 1948) TP 23703. 3 R. Becker and W. Döring: Ferromagnetismus. 365 (1939). J. Springer.

Jan 1, 1951

By Nelson Severinghaus

Following the end of hostilities of World War 11, a resurgence of industrial and home building has given impetus to the use of many products of the stone industry. Shortage and high prices of some building materials such as lumber have aided wider acceptance of materials such as concrete products which have been relatively plentiful and which have not risen so rapidly in price. Ingredients for many of these substituting materials come from the stone industries, often from by-products of stone operations. Most of the tonnage of the stone industry in the State of Georgia comes from granite and marble. There are extensive dimension stone operations in granite in the Elberton and in the Lithonia areas. Building and monumental marble from the Tate area has been used throughout the country. Cutting operations in both types of stone have their by-products in faulty blocks and in spalls. In the State there are three large crushed-stone plants utilizing granite, One near Camak, One near Lithonia and one at Stockbridge. All have had excess fines Or in in the past but this excess is largely disappearing with development of new uses. At times this "waste" has amounted to as much as 20 pct of the stone quarried. Handling Of this large tonnage from point of screening out to storage piles presented a costly problem and large areas were taken up by the piles. Crushed 'tone is generally sold with a a narrow margin Of price over cost, so any elimination of disposal cost or increase of income by marketing of by-products is highly desirable. By-products of Granite Dimension Stone It sometimes becomes difficult to differentiate between main product and byproduct. In the cutting of granite dimension stone in the Lithonia district of Georgia, a considerable quantity of remnants of Uneven shape and size is produced. The larger of these pieces have long found use as building rubble, particularly for retaining walls and building foundations (Fig I), They are broken down to one man size by plug drilling and wedging and by hammer. In recent times, demand for this former by-product has grown so that quarries have been opened for the production of rubble as a main product. Local masons have attained skill in using these irregular shapes to form economical and attractive walls. Areas such as Elberton, Georgia, which do not have a large building market nearby, tend to accumulate piles of large pieces of reject stone. When a road job or other local construction offers a quantity market for crushed stone, a portable crusher works this material down to crushed aggregate. Spalls and finer chips from granite stone-cutting operations have generally found their way into crushers and thence to the many uses for crushed aggregate. One company near Lithonia started marketing the smaller by-product crushed sizes for chicken grit about ten years ago. This use has grown to nation-wide distribution and the tonnage is now so great that they have opened a large quarry with

Jan 1, 1948

By Nelson Severinghaus

Following the end of hostilities of World War 11, a resurgence of industrial and home building has given impetus to the use of many products of the stone industry. Shortage and high prices of some building materials such as lumber have aided wider acceptance of materials such as concrete products which have been relatively plentiful and which have not risen so rapidly in price. Ingredients for many of these substituting materials come from the stone industries, often from by-products of stone operations. Most of the tonnage of the stone industry in the State of Georgia comes from granite and marble. There are extensive dimension stone operations in granite in the Elberton and in the Lithonia areas. Building and monumental marble from the Tate area has been used throughout the country. Cutting operations in both types of stone have their by-products in faulty blocks and in spalls. In the State there are three large crushed-stone plants utilizing granite, One near Camak, One near Lithonia and one at Stockbridge. All have had excess fines Or in in the past but this excess is largely disappearing with development of new uses. At times this "waste" has amounted to as much as 20 pct of the stone quarried. Handling Of this large tonnage from point of screening out to storage piles presented a costly problem and large areas were taken up by the piles. Crushed 'tone is generally sold with a a narrow margin Of price over cost, so any elimination of disposal cost or increase of income by marketing of by-products is highly desirable. By-products of Granite Dimension Stone It sometimes becomes difficult to differentiate between main product and byproduct. In the cutting of granite dimension stone in the Lithonia district of Georgia, a considerable quantity of remnants of Uneven shape and size is produced. The larger of these pieces have long found use as building rubble, particularly for retaining walls and building foundations (Fig I), They are broken down to one man size by plug drilling and wedging and by hammer. In recent times, demand for this former by-product has grown so that quarries have been opened for the production of rubble as a main product. Local masons have attained skill in using these irregular shapes to form economical and attractive walls. Areas such as Elberton, Georgia, which do not have a large building market nearby, tend to accumulate piles of large pieces of reject stone. When a road job or other local construction offers a quantity market for crushed stone, a portable crusher works this material down to crushed aggregate. Spalls and finer chips from granite stone-cutting operations have generally found their way into crushers and thence to the many uses for crushed aggregate. One company near Lithonia started marketing the smaller by-product crushed sizes for chicken grit about ten years ago. This use has grown to nation-wide distribution and the tonnage is now so great that they have opened a large quarry with

Jan 1, 1948

By K. R. Evans

The deformation mechanisms occurring in polycrys-talline, commercially pure titanium and a Ti-8 pct A1 alloy have been investigated and compared to earlier results by Levine on high-purity titanium single crystals and by Conrad on commercially pure titanium. In accord with Levine, two consecutive deformation mechanisms are observed to exist below 500°K with the transition temperature between mechanisms, Tc, strongly dependent upon interstitial composition. T, is found to be 210°. 375° -430°, and 450°K for alloys A large number of investigations have been conducted to determine the rate-controlling mechanisms of plastic deformation occurring in fcc and bcc metals. Very few investigations of a similar nature have been conducted for hexagonal metals. In fact, until very recently, magnesium is the only hexagonal metal which has been systematically investigated for determination of the rate-controlling deformation mechanisms.1"3 From these investigations, it was concluded that basal slip below 420°K occurs by the intersection of forest dislocations,1'3 while for prismatic slip the Peierls mechanism is rate-controlling at low temperatures with interstitial compositions of 0.024, 0.42, 0.61, and 1.13 at. pct expressed in terns of oxygen equivalents. The low-temperature mechanism is found to be an impurity obstacle mechanism in contrast to Levine's earlier conclusion of the Peierls barrier. Measurement of the activation parameters for deformation and estimation of the force-distance profile of the obstacles show their retarding force to be effective over longer distances from the obstacle as the interstitial composition increases. and thermally activated cross slip at higher temperatures. 2 The potential technological importance of titanium alloys has prompted recent studies of the deformation and fracture characteristics of titanium and its alloys. 4-8 Levine' systematically investigated the low-temperature deformation behavior of high purity titanium single crystals oriented for either basal or prismatic slip. It was concluded that the Peierls mechanism was rate-controlling at temperatures below 210°K, while above this temperature an undefined mechanism was rate-controlling. Conrad 7,8 concluded from an analysis of the composition dependence of the critical shear stress at 0°K and measurement of the activation parameters that the low-temperature deformation of titanium is controlled by an impurity

Jan 1, 1969

By Rollin Farmin

Rock pressure against the supports for underground workings in certain mines becomes sufficiently severe to crush sound timbers. The cost of maintenance of these mines increases critically as the workings are extended. "Heavy ground " and "swell-jng ground" are terms commonly applied to a condition of excessive pressure from the wall rock. Defined for the purposes of this paper, "heavy ground" delivers gravi-tative pressure on the supports of a mint opening; "swelling ground" delivers pressure arising from expansion of the wall rock. Mining problems created by heavy ground have been studied extensively by mining engineers, as in the recent Symposium on Block caving.' A parallel study of rock bursts2 attacks the field of ground that ruptures under strain. The problem of swelling ground, which has received less current attention, is the subject of this paper. An ExaMPLe of Swelling Ground Severe cases of swelling ground are found in the gougy shear zones in mines along the western Sierra Nevada, where the veins are accompanied by faults through altered serpentine, schist and slate. For example, along troublesome stretches in the ldaho Maryland mine, Grass Valley, California, swelling ground continues to crush drift timbers, with diminishing intensity, for 3 to 10 years after entry. During this period, from five to nine generations of crushed timber sets must be replaced and a large additional tonnage of scaly rock and wet gouge must be removed from the drift to make room for this succession of new timbers. After "the squeeze has been taken out of the ground" the timbers will stand for years, until they collapse from decay. Heaving of floor and footwall along drifts develops soon after the timber sets are placed and frequent grading down of the track is necessary to keep it serviceable and to maintain headroom. If sills are placed under the drift posts, the sets break more quickly and the track becomes impassable at once. When the floor is left Open? and the bottoms of posts and stulls are pencil-pointed, the scaly ground of the fault zone swells up around the timbers (Fig. I) instead of breaking them (Fig. 2). A foot or two of this encroaching ground is trimmed from the floor and lower sides of the drift several times before complete retimbering is necessary. when a set of timber fai1s under the Pressure of swelling ground, there is no immediate fall of timber and broken rock to fill the drift, as is customary in heavy, caving ground. Instead, ground swelling from sides, top and bottom gradually closes the opening, over a period of weeks or months, and no especial hazard to workmen is present while they have room to walk through the narrowing drift. Most

Jan 1, 1946

At 8 o'clock on the evening of Thursday, July 25th, the special train chartered by the Provincial Government for the Institute's use, pulled out of Toronto. Ten parlor cars and two dining cars made up the train. The culinary arrangements were under the personal supervision of Mr. McConkey, of Toronto. [ ] The Hon. Frank Cochrane, Minister of Mines, Lands and Forests, was the efficient host of the party. He was assisted by the Hon. Dr. Pyne, Minister of Education, and by Mr. T. W. Gibson and Dr. W. G. Miller. On arriving at Cobalt, the delegates were met by the following Committee Mr. A. A. Cole, representing the T. & N. 0. Railway; Messrs. R. W. Leonard and D. B. Rochester, deputies from the Cobalt Chamber of Mines ; Messrs. Run¬ning and Martin, from the Cobalt City Council; Messrs. McLeod and Ferland,

Jan 1, 1907

By F. G. Tahmoush, N. J. Grant, E. P. Abrahamson

The effect of grain size on the brittle -ductile transition temperature of pure iron and three dilute Fe-W alloys has been investigated by slow bend tests. The brittle-ductile transition temperature for pure iron increased with increasing grain sizes from 8000 to 500 grains per sq mm where the transition temperature then decreased with further increase in grain size. The dilute additions of tungsten lowered the transition temperature for fine grain sizes, suppressed a reversal of the curve in the coarse grained portion, and raised the transition temperature for this region. The frequency of twin occurrence increased with increasing grain size and decreasing temperature. The object of the present investigation was to re-examine the effect of grain size on the brittle -ductile transition of pure iron and several dilute Fe-W alloys. Current literature normally presents a simple relationship between grain size and the brittle-ductile transition temperature, namely, that the transition temperature increases with increasing grain size. Heslop and etch' have studied the transition temperature of mild steel by V-notch Charpy impact tests for the grain size range between 200 and 6000 grains per sq mm. The result was a linear plot of In 1-1/2 vs brittle-ductile transition temperature, where 1 is the grain diameter. Recent experiments by sipos2 revealed the possibility of a reversal in the slope of the grain size vs transition temperature plot for pure iron; however, his investigation was limited in scope, and the data obtained were insufficient to permit a definitive curve. The present investigation was undertaken in an effort to confirm or extend the grain size effect observed in iron by Sipos. PROCEDURE All alloys were vacuum induction melted, using 99.95 pct Fe containing 0.03 pct 0 and 0.004 pct C. Four ingots were made, ranging from pure iron to iron with 0.035 pct W. The chemical composition of each alloy, after processing, is given in Table I. The four alloys were prepared as 45 lb heats and cast into 4 in. diam by 16 in. molds. They were then extruded into 3/4 in. rods at 1800oF. Specimens for chemical analysis, taken from various positions along the rods, revealed no variation in tungsten content along the length. The extruded rods were reduced to 0.156 in. diam stock by a series of cold swaging operations involving intermediate vacuum annealing treatments. This procedure yielded a final cold reduction in area ranging from 10 to 90 pct. The swaged rods were chemically cleaned, cold pressed to a cross section of 0.10 by 0.18 by 1.0 in. long (2.54 by 4.73 by 25 mm). The specimens were wrapped in iron foil and vacuum sealed (10-4 mm Hg) in quartz. Various heat treatments at temperatures from 700" to 1300oC were utilized to produce grain sizes from 8000 to 1 grain per sq mm. Grain sizes were determined by measuring the average area of grains in a polished section. In specimens with grain size greater than 20 grains per sq mm, the total number of grains in the cross section was counted and then divided by the area to yield grains per sq mm. Grain size was measured both for longitudinal and transverse cross sections. The average of the two measurements was plotted vs transition temperature. An Instron Table Model testing machine was used to determine the transition temperature of specimens tested in three point horizontal bending. The specimen was supported by two 1/4 in. dowels one in. apart. Bending was accomplished with a push rod, the end of which had an 1/8 in. radius. The head speed was 50 in. per min. Temperatures were established through the use

Jan 1, 1963

By W. B. Finkeldey, C. H. Mathewson, C. S. Trewin

This paper was prepared upon request as a contribution to a symposium covering the manufacture, properties, and uses of the important non-ferraus metals. In approaching a subject as broad as this, there is a natural desire to build up a comprehensive and finished production which shall constitute a dependable source of information on all questions properly belonging to this branch of metal technology. There are, however, a number of circumstances, apart from the mere routine of labor and thought involved, which operate rather effectively against the possibility of completing such .an ambitious program at the present time. First of all, as far as any public record of results is concerned, the commercial rolling, drawing, and forming of zinc with relation to changes of structure and properties—and this we consider to constitute the clement~ of metal technology—might as well be an unpractised art. We have never seen a published photomicrograph showing the structural characteristics of either hard or soft sheet or strip, although the structure of castings has been frequently described, and other coarse-grained structures resulting from hard-hammering and annealing have been reproduced. Thus, an author in this field must proceed to his task without much assistance from the literature, and the outcome can represent only a personal estimate of principles, facts, or findings, and not a summary or survey of progress in the entire field as determined by varied experience, practice, and settled opinion.

Jan 1, 1921

By George L. Montgomery

In a recent article Heckler, Elias, and woods1 have described an automatic computer technique for plotting of pole figures. To anyone who has constructed pole figures manually from raw X-ray data, the development of computer plotting techniques has been a very welcome development. The purpose of the present note is to describe an alternative computer plotting method which, if somewhat less precise than the method described by Heckler et al., has the advantages of being faster and of not requiring the availability of a plotter. The plot is made directly by the printer of the terminal system and, by its nature, has a good deal of visual impact. Each character of output symbolizes a level of intensity. For example the numerals 1 to 9 might represent intensities referred to some reference obtained from a randomly oriented sample. Should more levels be required (this is seldom necessary) alphabetic or other characters may be used in addition. When these are arranged in the proper fashion, the result is a pole figure such as is shown in Fig. 1. It is the purpose of the computer program to transform the data and carry out the arrangement in a suitable manner. The computation is carried out on a line by line basis in order to reduce the amount of storage required and thus keep the program "small". It is, thereby, well within the limitations of the time-sharing systems which are becoming increasingly available. The inaccuracies introduced are slight and the plot can easily be made as precise as the technique used to collect the data. Comparison of pole figures produced by this method with those constructed manually shows a high degree of equivalence. To the present, the technique has been applied to reflected X-ray data only. X-ray data are collected in a manner identical to that described by Heckler et al. That is, as the goniometer rotates the specimen, a series of counts, accumulated over a preset time, is recorded. The method by which the proper symbol, representing an intensity level, is assigned to each print position is up to the ingenuity of the programmer. Perhaps the simplest method is to section the stereograph in the fashion of a polar net, and to assign all print positions lying within each segment a symbol representing the level of intensity recorded at the data point nearest to the center of the segment, see Fig. 2. The number and arrangement of the segments are selected to conform more or less with the number of accumulated counts and the geometry of the goniometer path used to collect them. Since the angular distance between accumulated counts is usually not infinitely controllable, it is impossible to locate one reading within each segment and, at the same time, maintain symmetry in the sectioning of the stereograph. This latter requirement is essential to keep the computer program simple and flexible. As an expedient it was found that the number of data points could be increased to conform with the number of segments, with very little loss of

Jan 1, 1969

By J. Price Wetherill

The coal-seams that are worked vary from 3 1/2 to 100 feet in thickness, and occur at all angles of inclination, but are never flat for any great extent. They contain coal, slate, and an unsolidified coal, called dirt by the miners, in various proportions, a uniform seam of coal alone being rare. The upper walls are composed of conglomerate, sandstone, or slate; the first two hard and solid in texture, and withstanding the action of the atmosphere and moisture sufficiently well to offer but little trouble to the mining operations; while the latter crumbles rapidly, owing, in part, to the decomposition of iron pyrites which it contains in large quantities, and in part to its own friable character, and requires constant care to avoid accidents to the men working below it, and to prevent its mixing with the coal mined. The floors are composed of slate. As in all mining operations, the general system pursued is to reach with a permanent outlet such a point in the seam as will

By R. G. Brown

Tars paper will present a general description of the different mineral belts in the Butte City region (limited, however, to the copper and contiguous silver veins) such as may serve to give an intelligent idea of the distribution and characteristics of the deposits, forming thus a groundwork of information, which it is hoped will have value, when later writers enter into particularized detail.

Jan 1, 1895

THE following employment items are mode available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of, the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. POSITIONS OPEN Mining Engineer with some engineering training, capable of doing mapping, surveying, exploration, geology and transit work. Location, New York State. Y7333. Mineral Dressing Engineer, B.S. Mining or Chemical Engineering, age to 35. Must have knowledge of flotation. Duties will be in applied research and field evaluation of cationic and anionic flotation agents. Salary, $3500 to $7000 depending on experience. Location, Chicago. R-8971. Geological Draftsman, 25 to 30, with some experience in working with a geologist. Salary, $5100 a year. Location, New York, N. Y. Y7153.

Jan 1, 1952

By Robert H. Richards, Richard W. Lodge

A great deal of speculation, as well as actual experiment, has been devoted to ascertaining the changes in the materials (luring their descent in an iron blast-furnace, affecting (1) the chemical constitution, (2) the mechanical condition, and (3) the arrangement of the materials. With a view to throw some light upon the third question, we constructed a model and tried experiments which are here described. Our model is a vertical section of a furnace, with the lines of the Edgar Thomson furnace D of 1885 for the use of which we arc indebted to Mr. Gayley. The model is 40 inches high, and made to scale (1/2 inch equals 1 foot), and the horizontal section of the space through which the charge falls at any point in the descent is 11/2 in. x d, d being the diameter of the furnace at that place. We are unable to say just where the idea of making this model came from ; perhaps, partly from The Principles of the Manufacture of Iron, and Steel, 1884, I. Lowthian Bell, p. 124 ; partly, also, from

Jan 1, 1888

By J. Jones-Parra, J. C. Calhoun

INTRODUCTION The purpose of this paper is to present the results obtained by solving the fractional flow' and frontal advance' equations to obtain oil recovery at water breakthrough as a function of the length of the system being flooded, the linear velocity of injection and the displacing phase viscosity. The method of solution makes use of the stabilized zone concept first presented by Terwilliger, et al3 when calculating saturation distributions in a gravity drainage system. In order to check the calculated results, the equations and method of solution were applied to the system on which Rapoport and Leas' reported experimental data. METHOD OF SOLUTION The solution of the fractional flow equation and the frontal advance equation is obtained by assuming that a water front forms to sweep the oil out ahead of it. There is ample evidence that under the proper conditions a water 'front does form. If this water front is not to dissipate, the water saturations which comprise it must have equal linear velocities. These water saturations are said to comprise the stabilized zone. Equation (2) indicates that for all these saturations and hence fw must plot as a straight line against saturation for those water saturations comprising the stabilized zone. The water saturations lying between the highest in the stabilized zone and the highest that can be achieved in the porous medium comprise the variable zone. Regardless of the numerical value of the length of the system, the variable zone must eventually span all of it, so that for long enough systems in Equation (1) will be small enough to be neglected. Hence, for the saturations in the variable zone Equation (1) can be simplified to In order to determine the composite fw function applicable to the entire range of saturations in the porous medium, it is necessary to find the water saturation which separates the stabilized zone from the variable zone. This dividing saturation must be on the curve defined by Equation (4), and a tangent curve at that point must pass through the initial water saturation to satisfy Equation (3). Hence, the valid fw curve is given by a straight line starting at the initial water saturation, tangent to the curve of Equation (4): and along the curve of Equation (4) from the point of tangency on. The point of tangency determines the water saturation dividing the zones. The length and shape of the stabilized zone can be found by solving Equation (1) for Integrating this expression numerically between any two saturations in the stabilized zone gives the distance separating these two saturations. By repeated integration, the saturation distribution of the stabilized zone can be determined. The total length of the stabilized zone is given by The integral appearing in Equation (5) is a function of the viscosity ratio, the capillary properties of the rockfluid system, the relative permeabilities, and the initial water saturation. Considering these variables fixed and designating the value of the integral by writing caw for and v/60 for q/A; Equation (5) becomes The saturation distribution of the stabilized zone can be integrated over its length and divided by the length to obtain the average water saturation The volume of water in the stabilized zone is then given by The average water saturation in the variable zone can be found by extending the straight line segment of (the segment joining Sw and Sw) until it intersects fw = 1.00. The saturation at the intersection is. This method of finding is nothing more than the graphical solution of the equation The volume of water in the variable zone at breakthrough is then given by Assuming no initial water saturation, the recovery at breakthrough expressed as percent pore volume is given by

Jan 1, 1953

By Eugene McAuliffe

THE Coal Division undertook its most ambitious program this year at the New York meeting, with six full' sessions and a luncheon on Monday which had a record attendance and at which the newly elected officers for the Division were announced. Eugene McAuliffe, president of the Union Pacific Coal Co., Omaha, Neb., was unanimously selected as Chairman; J. B. Morrow, preparation manager of the Pittsburgh Coal Co., as Vice-Chairman; and H. E. Nold, Ohio State University, Secretary. During the past year two new and interesting activities were conducted by the Division directed at stimulating the interest of junior and student members. Reports were presented at the luncheon meeting by the chairmen of these commit¬tees. J. B. Morrow. chairman of the paper prize awards, and H. N. Eavenson reported on the work of the mining machinery manufacturers fellowship, the work on which was completed the first of the year. Several excellent papers are expected from these two groups for the next meeting of the Division to be held in Pittsburgh some time in the fall. The regular six-session program was filled from start to finish with interesting papers and much discussion, but unfortunately not enough time for the latter. The papers covered the field of prospecting, mining methods, preparation, utilization, mechanization, and safety, and all through the program we were constantly reminded of the value and need of research in the coal industry.

Jan 1, 1936

By F. L. Ruhlman, Max C. Eastman

The termination of the recent war marked a major changc in the oil-field operations at. Elk Hills. Production was greatly curtailed, various experimental production projects were started, and a long-range exploratory program was inaugurated. Production was reduced from the wartime peak of 65,000 bbl per day to the current rate of about 8ooo bbl per day in order to maintain an available source of crude that can be drawn upon during a national emergency. The existing production rate is deemed essential to carry on the experimental production projects. These projects are being conducted to determine the best methods and means of maintaining the Reserve, shut in, but in a state of readiness to produce the maximum quantity of oil in the most expeditious manner. Projects now being investigated include: (I) protection of surface equipmerit; (2) repair of wells that might damage the reservoir; (3) gas injection; (4) water eneroachment, (5) gravity drainage. An exploratory program is being carried on to determine the amount of recoverable oil in the unexplored portions of the Reserve. The Shallow-zone exploration is practically completed, but owing to the complexity of the Stevens structure and the magnitude of the oil discoveries in the Stevens, exploration will probably continue in that zone for another two years. Introduction Summary of Development History of Elk Hills Although a detailed history of Elk Hills oil field is presented in various publications,1,2 a summary of its unusual development and production history will be given in order that the present problems may be more readily understood. The first development that resulted in commercial production was in the central part of the Reserve. The first well, Hay No. I, in sec 36-R,* was completed in January I9I9, and was soon followed by 37 Others in the same general area. It is commonly referred to as the Hay-Carman area and was shut in in stages from 1925 to 1934 as a result of litigation regarding the title to the land. Not being highly producti,, only about 6½ million barrels of oil with a large volume of gas was produced from the area prior to the shutdown. Shortly after the start of the development of the Hay-Carman area, drilling was started 6 miles east in sec 36-S' Tupman NO. I came in for 5000 bbl per day early in I92o, It was followed by more than 200 others in the next few years, and the field became one of major importance. Produc-

Jan 1, 1949

By R. D. Longyear

[Some Problems Involved in the Interpretation of Diamond-drill-hole Sampling and Surve ing (paper by J. J. Collins, Mining Tech., Jan. 1946). ............... I Geologic Interpretation of Magnetic Exploration on the Mesabi Range, Minnesota (paper by R. H. B. Jones, Mining Tech., July 1946) ................... 2] DISCUSSION R. D. LONGYEAR.*-Mr. Collins is to be commended very highly for the brief summary he has made of the currently used methods of taking diamond-drill sludge samples and the principles involved in evaluating the results. This paper should stimulate further discussion and research on this vitally important problem. It is particularly imperative that geologists and engineers know when assay results on sludge recovery can be accepted quantitatively and when they must be considered only qualitatively. In most cases where the sludge recovery is less than 95 per cent or more than 125 per cent, it is safest to consider the assays as of qualitative value only. Certain cases, however, are known where a relatively small proportion of the sludge sampling will give a reasonably accurate measure of the value of the total sample. One such case is ore in which the valuable mineral is of approximately the same specific gravity as the waste mineral, such as chalcopyrite in a massive pyrite body. The essential point is to determine the degree of accuracy of sludge sampling in any given drilling project and to weigh the results accordingly. It should be emphasized, however, that sludge sampling can be made reliable in many localities where careless practice produces unreliable results. In many instances, it is desirable to empty the core barrel in the core shack instead of at the drill, so that the engineer can examine the core as it first comes from the core barrel. It should be pointed out, however, that the drill * E. J. Longyear Co., Minneapolis, Minnesota. runner should be permitted to study the core to guide his future drilling. It is hoped that with the return of more normal conditions after the war geologists, engineers, contractors, and manufacturers will be able to carry on more research along the lines of improved core-barrel design and drilling technique with the objective of increasing core recovery so as to eliminate as far as possible the necessity of relying upon sludge samples. H. M. ROBERTS.*-Whoever in the future will have to do with the search for ore bodies and their exploration will have frequent occasion to refer to the clear and comprehensive summary on diamond-drilling methods by John Collins. His review of the experience of the last 40 years in this technique is invaluable. As Dr. L. D. Ricketts wrote in 1932, "The principles on which an art is founded are usually few and necessarily basic in nature, but he who wishes to achieve the power to select his aides and give success to important undertakings that may be intrusted to him in the future must ordinarily undergo years of drudgery in order to gain the experience that will enable him to distinguish such fundamentals through the haze of reinforcing detail that clothes and tends to disguise them."[t] Ricketts went on to say that since the beginning of the century there has been much

Jan 1, 1946

By William E. Ford, Edward Salisbury Dana

A. Anhydrous Carbonates The Anhydrous Carbonates include two distinct isomorphous groups, the CALCITE GROUP and the ARAGONITE GROUP. The metallic elements

Jan 1, 1922

By B. H. Sage, W. N. Lacey

The growing background of experimental information concerning the volumetric and phase behavior of binary and ternary hydrocarbon systems is used as the basis for a comparison of these systems with naturally occurring hydrocarbon mixtures under conditions representative of underground petroleum reservoirs. The qualitative and semiquantitative similarities and differences between the two types of systems are considered in reference to the possibilities and limitations of using experimental data on binary and ternary systems for predicting the volumetric and phase behavior of naturally occurring hydrocarbon mixtures of low molecular weight. The possible influence on such phase behavior of water, hydrogen sulphide, nitrogen, and components of relatively high molecular weight is discussed. INTRODUCTION During the past two decades much effort has been devoted to the study of the volumetric and phase behavior of pure paraffin hydrocarbons and of binary and ternary mixtures of these compounds. Many of these studies were carried out with the direct objective of utilizing a knowledge of the detailed characteristics of binary and ternary mixtures of the lighter paraffin hydrocarbons for predicting the behavior of more complex mixtures. The ability to make such predictions with accuracy would be of great value in petroleum production and refining. Although the behavior of the methane-propane system' served at one time as a qualitative illustration of the probable characteristics of the more complex hydrocarbon mixtures found in nature, it' fell far short of requirements for quantitative predictions. The present paper endeavors to indicate the relation of the more recently accumulated information concerning the behavior of binary and ternary hydrocarbons to this problem. In discussing binary and ternary systems as examples pointing toward the behavior of multi-component systems no effort is made to present new methods of predicting the characteristics of natural hydrocarbon mixtures. Preliminary proposals have been made elsewhere for the prediction of volumetric phase equilibrium and thermodynamic data for multicomponent mixtures, utilizing as a basis the behavior of binary and ternary systems. Numerous other proposals have been made. That based upon the concept of a pseudo-critical state" has proved to be of value to the petroleum industry. Concurrently with this study of binary and ternary systems investigations have been made of natural hydrocarbon systems. Of the many publications reporting such experimental information only a few examples will be mentioned. A number of studies of black oil and natural gas have been made and much attention has been directed to extended and detailed investigations of the behavior of fluids in condensate fieldS 16,17,18,19,20. This work has been supplemented by some studies of the separation of bitumen from natural hydrocarbon liquids The over-all behavior of such systems has been used in predicting the volumetric and phase behavior of naturally occurring mixtures This background of experimental and correlated information concerning the behavior of multicomponent hydrocarbon systems also permits a direct comparison of the characteristics of binary and ternary aliphatic systems with those materials produced from underground reservoirs. PRESENTATION OF DATA The primary limitation encountered in using binary and ternary aliphatic hydrocarbon mixtures as examples of the characteristics of the fluids encountered in underground reservoirs lies in the existing lack of knowledge of the quantitative effect upon behavior of the presence of several important constituents, notably hydrocarbons of high molecular weight, water, carbon dioxide, hydrogen sulphide, and nitrogen. The presence of substantial quantities of hydrocarbons of fairly high molecular weight serves to increase the complexity of the phase behavior of natural systems. No simple systems yet studied give adequate guidance in this regard. The influence of such materials of high molecular weight was indicated earlier",?' to an extent which serves to show that definite limitations now exist in the correlation of simple and complex systems. However, significant progress is being made in filling gaps in the information. For example, similarities in the behavior of fluids in condensate fields with that of binary and ternary systems are becoming more systematically evident. A few studies of the behavior of water in paraffin hydrocarbon systems have been made Results of investigations of mixtures of carbon dioxide and the lighter hydrocarbons also are available Limited work has been reported con-

Jan 1, 1949

By W. N. Lacey, B. H. Sage

The growing background of experimental information concerning the volumetric and phase behavior of binary and ternary hydrocarbon systems is used as the basis for a comparison of these systems with naturally occurring hydrocarbon mixtures under conditions representative of underground petroleum reservoirs. The qualitative and semiquantitative similarities and differences between the two types of systems are considered in reference to the possibilities and limitations of using experimental data on binary and ternary systems for predicting the volumetric and phase behavior of naturally occurring hydrocarbon mixtures of low molecular weight. The possible influence on such phase behavior of water, hydrogen sulphide, nitrogen, and components of relatively high molecular weight is discussed. INTRODUCTION During the past two decades much effort has been devoted to the study of the volumetric and phase behavior of pure paraffin hydrocarbons and of binary and ternary mixtures of these compounds. Many of these studies were carried out with the direct objective of utilizing a knowledge of the detailed characteristics of binary and ternary mixtures of the lighter paraffin hydrocarbons for predicting the behavior of more complex mixtures. The ability to make such predictions with accuracy would be of great value in petroleum production and refining. Although the behavior of the methane-propane system' served at one time as a qualitative illustration of the probable characteristics of the more complex hydrocarbon mixtures found in nature, it' fell far short of requirements for quantitative predictions. The present paper endeavors to indicate the relation of the more recently accumulated information concerning the behavior of binary and ternary hydrocarbons to this problem. In discussing binary and ternary systems as examples pointing toward the behavior of multi-component systems no effort is made to present new methods of predicting the characteristics of natural hydrocarbon mixtures. Preliminary proposals have been made elsewhere for the prediction of volumetric phase equilibrium and thermodynamic data for multicomponent mixtures, utilizing as a basis the behavior of binary and ternary systems. Numerous other proposals have been made. That based upon the concept of a pseudo-critical state" has proved to be of value to the petroleum industry. Concurrently with this study of binary and ternary systems investigations have been made of natural hydrocarbon systems. Of the many publications reporting such experimental information only a few examples will be mentioned. A number of studies of black oil and natural gas have been made and much attention has been directed to extended and detailed investigations of the behavior of fluids in condensate fieldS 16,17,18,19,20. This work has been supplemented by some studies of the separation of bitumen from natural hydrocarbon liquids The over-all behavior of such systems has been used in predicting the volumetric and phase behavior of naturally occurring mixtures This background of experimental and correlated information concerning the behavior of multicomponent hydrocarbon systems also permits a direct comparison of the characteristics of binary and ternary aliphatic systems with those materials produced from underground reservoirs. PRESENTATION OF DATA The primary limitation encountered in using binary and ternary aliphatic hydrocarbon mixtures as examples of the characteristics of the fluids encountered in underground reservoirs lies in the existing lack of knowledge of the quantitative effect upon behavior of the presence of several important constituents, notably hydrocarbons of high molecular weight, water, carbon dioxide, hydrogen sulphide, and nitrogen. The presence of substantial quantities of hydrocarbons of fairly high molecular weight serves to increase the complexity of the phase behavior of natural systems. No simple systems yet studied give adequate guidance in this regard. The influence of such materials of high molecular weight was indicated earlier",?' to an extent which serves to show that definite limitations now exist in the correlation of simple and complex systems. However, significant progress is being made in filling gaps in the information. For example, similarities in the behavior of fluids in condensate fields with that of binary and ternary systems are becoming more systematically evident. A few studies of the behavior of water in paraffin hydrocarbon systems have been made Results of investigations of mixtures of carbon dioxide and the lighter hydrocarbons also are available Limited work has been reported con-

Jan 1, 1949