Search Documents

By R. D. Nelson

The purpose of this technical note is to briefly present some data on a phenomenon—recrystallization with concurrent deformation—that has been found to occur in a plutonium. This phenomenon is unusual because a plutonium is considered brittle, not easily deformed, and not easily recrystallized; the a phase is simple monoclinic having 8 atoms per unit cell and it is stable below about 115°C. The properties of the recrystallized metal were different from the as-cast metal. Even though a plutonium is difficult to deform, Ianniello successfully rolled it' and he also observed some recrystallization at 120°C.2 Pavlick and Hanson3 detected some recovery at 109°C but they observed no recrystallization. Gardner4 and Bronisz5 studied the compression properties up to 100°C but they did not report having seen recrystallization. In the present deformation studies of electrorefined plutonium pronounced recrystallization took place concurrently with plastic deformation in compression between 24" and 115°C. The metal contained less than 300 ppm total impurities with the major impurities being 100 ppm Am, 30 ppm C, 40 ppm W, and 25 ppm U; all other impurities totaled less than 100 ppm. The compression specimens were machined to dimensions of 1.2 cm long and 0.8 cm diam from as-cast rods having a density of 19.65 g per cu cm. They were heated to the test temperature in a high-temperature silicone fluid that was evacuated to 10-4 Torr. With this procedure the specimens oxidized a negligible amount, and the temperature was maintained within ±0.2°C for times up to 3 weeks. Deformation and recrystallization

Jan 1, 1969

By E. J. Schmitz

This novel safety-lamp, which was first introduced in some of the German coal-mines in 1882, at once attracted general attention in the coal-districts of Europe. Objections which arose during the early stages of its use at the mines have gradually died away with the increase of experience in handling the lamp 011 the part of the miners, and the continual efforts to perfect it on the part of its inventors. Wolf's lamp has rapidly surpassed all its rivals, and has already a greater distribution on the Continent than any one of its older sisters. In the course of two and a half years, the manufacturers have sold 25,000 of the lamps, besides remodelling several thousand rapeseed-oil lamps. This great success, which of itself speaks loudly enough as to the superiority of the Wolf benzine-lamp, is corroborated by both official and private reports, which all agree in pronouncing this lamp the best yet brought forward. It was described in a paper by Mr. Eugene B. Wilson, read at the Chicago meeting of the Institute, in May, 1881,* in which its salient merits were briefly but clearly indicated. Every previous improvement of the original Davy lamp has been directed to one or more of the following main points: 1. Light of greater and more uniform intensity. 2. Freedom from smoke or soot, which clogs the gauze and other parts of the lamp. 3. A greater safety and sensitiveness in the presence of firedamp. 4. An illuminating material which, satisfying the foregoing conditions, should be also cheap. 5. A lock which could not be opened in the mine by the miner. 6. An arrangement for lighting without opening the lamp. 7. An arrangement for changing the size of the flame in the closed lamp, to supersede the picker, the danger from which is explained in Mr. Wilson's paper, already cited. It may safely be said that wolf's lamp was the first to secure all these objects. The adoption of benzine instead of rapeseed-oil (previonsly the best illuminant) has completely satisfied conditions 1, 2, 3, and 4. Benzine gives a much clearer, stronger, and more uni-

Jan 1, 1886

By Charles H. Fulton

FOR some time it has been thought that there should be > closer relationship between the members' of the Institute engaged in education in the mining schools, the mining, metallurgical, ceramic, and geological departments of universities, and the members of the Institute actually engaged in the production of mineral products and the operation and direction of works. The American Society of Chemical Engineers and the American Ceramic Society have for some years past devoted especial attention to the educational matters of their respective fields. The Engineering Foundation, representing the great engineering societies of the country, is deeply interested in technical education and maintains a Committee on Educational Research.

Jan 1, 1932

Use of rock grinding media in a mill at Tennessee Copper Corp. was mentioned in the MINING ENGINEERING Annual Review. (February 1953, page 158). Because interest in use of self-grinding media continues high we asked F. M. Lewis, Superintendent of Concentration at Tennessee Copper, to supply more details on this trial, and of plans to expand use of rock media in their mills that grind marble. Here is what he reports.

Jan 5, 1953

By P. E. Doherty, B. Chalmers

Subboundaries may be revealed in aluminum by the formation of pits on the surface during cooling from elevated temperatures. The pits do not form in the vicinity of high- or low-angle boundaries. They are attributed to the condensation of vacancies from a super saturation produced during coolirzg. Using the vacancy pit and Schulz X-ray techniques for observing low-angle boundaries, a study was made of the transition from the nearly perfect seed to the striated structuke characterist-ic of aluminum crystals grown from the melt. It was found that the individual striation boundaries develop by the coalescence of very small-angle boundaries, as well as by the addition of individual dislocations. Several mechanisms for the formation of striations are discussed. Evidence was found suggesting that a super-saturation of vacancies exists near a growing interface, and it is proposed that the resulting climb of existing dislocalions produces "half'-loops" at the interface, which combine to form the low-angle striation boundaries. LINEAGE, or "striation" boundaries, have been studied in detail by Teghtsoonian and Chalmers 1,2 in crystals of tin grown from the melt, and by Atwater and Chalmers3 in lead. They found that single crystals grown from the melt consist of regions which are separated by subboundaries that lie roughly parallel to the growth direction. A difference in orientation of 0.5 to 3 deg exists between the striated regions; the misorientation is such that the lattice of one region could be brought into coincidence with the lattice of its neighbor by a rotation about an axis approximately parallel to the direction of growth of the crystal. They observed an incubation distance for the formation of striations which increased with decreasing growth rate. They also found that in any crystal, the sum of all rotations of the lattice in one sense, in going from one striation to the next, is very nearly equal to the sum of all the rotations in the opposite sense. A striation boundary, which is a low-angle grain boundary, can be described as an array of dislocations. If it is assumed that suitable dislocations are introduced into the crystal during solidification, the formation of striation boundaries can be explained as a result of the migration of the disloca- tions into arrays. The formation of arrays is energetically favorable since the energy of an assembly of dislocations can be reduced by the interaction of the stress fields when a suitable array is formed. This investigation presents and interprets new information concerning the nature and origin of striation boundaries in aluminum. EXPERIMENTAL TECHNIQUE Single crystals of high-purity aluminum (Alcoa 99.992 pct) were prepared by horizontal growth from the melt.'' The specimens were subsequently electropolished in a solution of 5 parts methanol to 1 part perchloric acid kept between -10° and 0°C in a bath of dry ice and alcohol. The current density was approximately 6 amps per sq in. Doherty and Davis9 have shown that in aluminum sub-boundaries with misorientations of not less than several seconds of arc may be revealed by the vacancy pit technique. During cooling from elevated temperatures pits form on electropolished surfaces of aluminum crystals as a result of the condensation of vacancies.11 Pits do not form in the vicinity of small- or large-angle grain boundaries, presumably because such boundaries act as sinks for vacancies. Boundaries of misorientations down to 3 sec of arc are revealed as pit-free regions, see Fig. 1. The Schulz X-ray technique12 was used to determine the angular misorientations of subboundaries. In this method, white radiation from a micro-focus X-ray tube is used to produce an image of a fairly large area of a single crystal surface. Subboundaries cause splitting in the diffracted image, see Fig. 2. Misorientations down to about 15 sec of arc may be observed with this technique. OBSERVATIONS AND DISCUSSION Figure 1 shows a striated aluminum crystal grown at 10 cm per hr etched by the vacancy pit technique. An incubation distance of about 1 cm is observed before the initiation of striation boundaries. Fig. 2 is a Schulz X-ray photograph of a striated crystal similar to that shown in Fig. 1. A large area of the crystal was studied by means of a series of photographs. Fig. 2, which is a reflection from the (100) plane, included about the first 4 cm of crystal to freeze. There is an incubation distance of about 1 cm, and a distance of about 2 cm over which the angle of misorientation builds up to its final value of approximately one degree. Some twist component can be seen in Fig. 2 at the right side of the photograph. From Fig. 2 it can be seen that the sum of all rotations of the lattice in one

Jan 1, 1962

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872 R W RAYMOND 1873 R W RAYMOND 1874 A L HOLLEN 1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 ECKLEY B COXE 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882

Jan 1, 1910

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872 R W RAYMOND 1873 R W RAYMOND 1874 A L HOLLEN 1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 ECKLEY B COXE 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882

Jan 1, 1910

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872 R W RAYMOND 1873 R W RAYMOND 1874 A L HOLLEN 1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 ECKLEY B COXE 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882

Jan 1, 1910

By AIME AIME

I would like to ask Bob Merrill whether he considers that horizontal concave curvature of a slope has any stabilizing effect, such as Jenike 1 suggested several years ago. The stabilizing effect is due to the restraint offered to radial movement by the curvature. We found in laboratory tests that if we constrained the rock with the same stresses as those measured in the pit then it would sustain a maximum stress about two or four times greater than when the same rock type was unconstrained. We are therefore definitely of the opinion that a constrained situation in a slope is favorable towards stability.

Jan 1, 1967

By R. A. Generes, H. C. H. Darley

Laboratory tests showed that at elevated temperatures a reaction takes place between all metal hydroxides and clay muds, which results in a thickening or solidifying of the mud, the extent of which depends on the nature of the ingredients. Calcium hydroxide gave the strongest solidification whereas barium hydroxide only caused a mild thickening, indicating that the use of barium hydroxide muds instead of lime muds would be a good way of preventing high-temperature solidification. It was found possible to prepare barium mud in the laboratory with caustic soda and a thinner in the same manner as lime muds, and these barium muds had the same or better toleration of high solids content, resistance to salt contamination, and low gel strengths as the corresponding lime muds. Three field trials have been made with barium mud. The principal difficulty encountered was in determining the correct proportions of the tourly treatments required to maintain low gel strengths. A satisfactory systern was finally developed, and low gels were maintained throughout the third test. The wells on which the trials were made were not carried deep enough to test the resistance to solidification adequately, but oven tests at 350°F were made periodically and no tendency to solidification was noted except immediately after severe cernent contamination had introduced excessive amounts of calcium into the system. Although barium hydroxide costs considerably more than lime, the total mud costs were as low, and on the last well significantly lower, than the average cost of lime mud wells drilled in the vicinity. INTRODUCTION The advantages of repressing dispersion and hydra-tion of clay cuttings carried in the mud, particularly when drilling through thick clay formations, are well recognized. This repression is generally achieved by the use of lime, and lime muds have in consequence the desirable characteristics of high toleration of solids, low thixotropy, and good resistance to contamination. They have, however, the disadvantage of high-temperature solidification. This phenomenon has been described in detail by Gray et al, who have shown that it is the result of a chemical reaction between the hydroxides and the clay minerals. The work described in this paper was undertaken to find a substitute for lime which would not cause this solidification. LABORATORY EXPERlMENTS The principal positive requirement for a substitute for lime is that it should repress the hydration and dispersion of clay. It is well known that monovalent cations promote hydration while polyvalent cations repress it. Therefore, a few representative polyvalent salts and hydroxides were tested to determine whether they could be used as substitutes for lime. Their efficiency at repressing hydration and dispersion was measured by means of the clay-volume test. It has been shown elsewhere' that this test is a good measure of degree of dispersion of clay in suspension and that hydration accompanies and correlates with dispersion, so that measuring one measures the other. The test is made by centrifuging a 1:100 mixture of mud and 1-N NaCl and observing the volume of sediment—the greater the volume, the greater the dispersion. The tendency to caux solidification was measured by heating the muds in pressure vessels for 16 hours at 150°F and 370°F. An approximate quantitative

Jan 1, 1957

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

The microstructural stability of 59 carbon and low alloy steels after 34,000 hr exposure at 900' and 1050°F, including the weld heat-affected zone, is discussed. The tensile and creep rupture properties of the parent metal of many of the steels before and after 10,000 hr exposure are presented. SEAMLESS pipe has been used for many years at elevated temperatures. When seamless first began to be used, operating temperatures and pressures were relatively low and the steel produced adequately met the existing requirements. The need for knowledge of creep properties and graphitiza-tion was nonexistent. Today the requirements for tubular products have changed considerably. Operating temperatures and pressures are increasing continually and corrosion, particularly at high temperatures, presents a problem. Carbon steels have, under these conditions, certain economic advantages particularly in oil refinery use. However, the use of low alloy steels in the generation of steam power has increased appreciably due to the influence of molybdenum on creep strength and the control of graphitization with chromium. The behavior of carbon and certain low alloy steels after long periods of exposure at 900° and 1050°F (480° and 565°C) has been investigated. The steels were examined before and after 10,000 to 34,000 hr exposure. Results obtained with material exposed at 1200°F (650°C) are not presented due to the severe oxidation and resulting decarburiza-tion after long periods of exposure. The graphitization characteristics of carbon and low alloy steels are of fundamental concern to the users of these materials. This is particularly true where welded joints are employed. In order to evaluate properly the behavior of steels at elevated temperatures, it is desirable to employ not only long periods of exposure under controlled conditions, but to use material with known properties and steelmaking practices. The purpose of this investigation has been to study the microstructure of the weld and the tensile and creep rupture properties of the parent metal after long periods of exposure at elevated temperatures. In the report'.' of a previous investigation data were presented on the microstructure, impact strength, hardness, and oxidation characteristics after 10,000 hr exposure at elevated temperatures. When this investigation was planned, methods for controlling the graphitization characteristics of steel were not established and, therefore, a number of special alloy steels were included in the study. During the exposure of these steels, the influence of aluminum in accelerating the rate of graphitization and the inhibiting power of chromium were established by various investigators. Also, the vanadium-bearing steels, because of their outstanding creep properties, received attention. As a result of these developments, considerable progress has been made in the field of high temperature tubular products, and the necessity for special alloys to prevent graph-itization has been restricted largely to the use of chromium. Material Chemical analysis, deoxidation treatment, and austenitic grain size of the 59 steels discussed in this paper are shown in Table I. The steels were forged to 1x1 in. bars with the exception of steels 12B, 12DX, 12DY, 12DZ, 70, 70A, 72 to 78, 82, and 83 which were machined from heavy wall pipe. All bars were surface ground before exposure. Heat treatment before exposure is shown in Table 11. The majority of the steels included were melted in either a basic open hearth or basic electric furnace; how-

Jan 1, 1955

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962

By W. J. Shearer

A COMPARISON of statistics relating to coal min-ing in Great Britain and the United States leads one to suspect widely differing conditions and practice. A brief review of some of the conditions may enable American mining men to appreciate more fully the difficulties with which British engineers are faced, and to some extent explain why American, coal can be sold f.o.b. mine at the present time at about 50 to 60 per cent of the cost of British coal at the mine, and why British man-shift outputs fall far below American at present being less than 30 per cent. Bulman gives the average depth of 6-ft. seams. in Britain at 1350 ft., and of 2-ft. seams at 517 ft. George S. Rice states that 90 per cent of American coal 'is taken from less than 600 ft. Much English coal is taken below 2000 ft. and some below 3000 ft. The total influence of depth on cost is not always evident. Room work as known in America becomes less advisable with increasing depth, as pillars crush badly if left -for any length of time. A limited amount of bord and pillar work, taking very small amounts of coal in the first working, takes the place of room work, with rapid working of the pillars as soon as the panels are broken. Ventilation difficulties increase tremendously with depth and thinning coal. In America the chief use of air underground is to dilute gas. In Britain it serves a dual purpose, in many cases the amount of air cir-culated being far in excess of the quantity necessary to dilute gas to reasonable proportions. At great .depths rock temperatures exceed-95 deg. F., and great volumes of air are necessary for rock cooling. At these high temperatures humidity becomes an important factor. At present a great deal of research is under way to find methods of overcoming the troubles experienced with high temperature and humidity in deep mines.

Jan 8, 1928

By Michael J. Messel

OF the various minerals that occur in fibrous form known as asbestos, chryso-tile is the variety most in demand for commercial uses, and, last year, over 683,000 tons of the various grades were produced in Canada and United States, exclusive of African and Russian production, which figures are uncertain. Production has not been able to keep up with the increased demand, and an acute shortage exists. Canada, Russia, and Africa are still the most important producers. However, Russia consumes most of its production at home and exports very little. The United States consumes over 60 pct of the total production and produces only about 4 pct of the total from deposits in Vermont and small quantities from Arizona. This paper will review mainly, some of the more recent developments concerned with the extraction and processing of this fibrous mineral for various industrial uses, such as textiles, insulation, building materials and brake linings. Four of the more important factors that have influenced recent developments are: 1. The lack of discovering and developing new deposits of any important size to supply the increased demand. 2. Rapid postwar expansion of industrial uses, especially in asbestos cement products, together with in-rreased manufacturing facilities. Euro-peal) countries are again back on the market with their demand. 3. The ability of manufacturers to develop their technique of blending fibers and obtaining more utility value out of each ton of fiber, together with the utilization of shorter grades of fiber to obtain equally as good products. In the past, many manufacturers were wasteful in their use of fibers. 4. The struggle for reduced operating costs, in face of increased wages and prices of supplies, together with the necessity, at some mines, to change the method of mining from open quarry to underground. Most of the recent capital invested in the asbestos mining industry has gone into more efficient extraction of the fibers from the existing ore, especially in the recovery of the shorter grades. There has been very little new plant expansion. Progress in the utilization of shorter fibers has been so far reaching that some of the mining companies are retreating present tailings as they leave the mill, and others are considering retreating of the old tailing dumps for recovery of fibers that, until recently, were not saleable and were discarded as part of the tailing. Many of these dumps contain much valuable fiber from days when milling was very inefficient. It might be appropriate to mention here that the present known asbestos reserves of proved commercial value (excluding Russia) are being depleted at an alarmingly rapid rate, about 10,000,000 tons of ore is being mined annually. No new deposits have come into production during the last 15 years, with the exception of certain deposits in Africa, which are the most promising, and minor developments in Canada, Venezuela, Cyprus, Australia, and Brazil. The African deposits are the only ones that hold promise of developing large reserves. Unless new deposits are developed, in twenty years or maybe sooner, the supply picture will not be a very bright one. Stimulated by the acute shortage, increasing fiber prices and technical developments, many new areas are being prospected in Canada, United States, New Zealand, Newfoundland, South America, Europe, Africa, and China. From information now available, it appears that no real progress has been made in duplicating this rare development of nature by producing synthetic asbestos. The most promising experiments were carried out at the University of Leipzig, but they seem far from practical. There has been marked progress in fiber glass manufacture, but so far, it has replaced asbestos only in very few instances for minor uses. Asbestos ore and the fiber it yields are different in some respect at each mine and vary usually in the following: 1. Percentage of fiber content by weight to the gangue. 2. Variations in proportions of long and short fibers, some deposits being predominantly long fiber and others short fiber. 3. The hardness of the rock in which the fiber occurs. 4. The nature of the fiber, as to

Jan 1, 1950

By Neils Hansen

The microstructure of dispersion-strengthened aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum oxide has been examined by optical and transmission electron microscopy, and the flow stress has been determined at room temperature and at 400C by tensile testing. Products were examined as recrystallized and as high-temperature extruded, and the microstructures consisted of a fine dispersion of oxide particles in a matrix divided by respectively recrystallized grain boundaries and subgrain boundaries. The flow stress (0.2 pct offset) at room temperature of recrystallized dispersion strengthened aluminum aluminum-oxide products is the superposition of dispersion strengthening and grain boundary strengthening. This superposition has been found to be linear. The flow stress (a) can be related to the grain size (t) by the Petch equation: ing content of oxide and k is a constant independent of the oxide content. For extruded products a similar relation has been found by replacing the grain size by the subgrain size. The k-value is of the same order for the two types of structure, which shows that the subgrain boundaries are as effective slip barriers as grain boundaries. Tensile testing at 400C of re-crystallized and extruded products shows that oxide dispersion strengthening is very effective, whereas the strengthening effect of grain boundaries and subgrain boundaries is small. THE microstructure of dispersion-strengthened products consists of hard particles finely distributed in a metal matrix. The strengthening effect of the dispersed phase has been fairly well established,1 and it has been found that the size and volume fractions of the dispersed particles are important structural parameters. However, in many dispersion-strengthened products which have been worked and heat-treated during manufacture the matrix is divided into well-defined grains or sub-grains, which may also have a strengthening effect. A model of the matrix strengthening in dispersed products worked during manufacture has been proposed,2 introducing the energy of the structure as a strengthening factor, especially at low temperatures. A difficulty in this model is, however, to relate this (stored) energy to the structural parameters directly observable as for instance grain size. The strengthening effect of the matrix grain size after recrystallization has been in- vestigated for nickel-thoria (TD-Nickel) products3 and for copper aluminum-oxide products. Conclusive results were, however, not obtained as the grain size of TD-nickel was constant. 5 to II , after recrystallization at temperatures from 700 to 1200°C and as the copper products containing 5 to 1 wt pct of aluminum oxide could not be recrystallized even after severe cold reduction and heat treatment at 1050C. For aluminum aluminum-oxide products containing from 1 to 5 wt pct of aluminum oxide it has been shown that the tensile strength at room temperature decreases when an extruded product is cold-worked and recrystallized. The matrix in the extruded products is divided into well-defined subgrains of micron size, and as the grain size of the recrystallized products is about two orders of magnitude higher, it is obvious that grain boundary strengthening occurs. Preliminary results8 have indicated that the flow stress containing no grain boundaries, A is a constant and t is the subgrain size. At elevated temperatures the effect of boundaries is more complex; it has been shown11 that recrystallized products having an oxide content of about 3 wt pct are more creep resistant than extruded material in the temperature range 400° to 600°C, whereas on application of a higher strain rate the tensile flow stress (0.2 pct offset) is higher in extruded than in recrystallized aluminum—5 wt pct aluminum oxide products at temperatures from room temperature to 427°C (800), Finally it has been shown12 that the Brinell hardness at 350°C of extruded products having about the same content of aluminum oxide increases with decreasing grain size, determined by X-ray line-width measurements. The present study was undertaken to obtain a quantitative relationship between the tensile strength and the grain size of aluminum aluminum-oxide products in the recrystallized as well as in the extruded state. The tensile testing was performed at room temperature and at 400uC. The grain size of the recrystallized products was varied by changing the degree of cold-work preceding the recrystallization heat treatment. In extruded products grain (or subgrain) size variations were obtained by high-temperature heat treatment after extrusion. EXPERIMENTAL a) Materials. Aluminum aluminum-oxide products have been manufactured by consolidation of aluminum powder covered with a layer of aluminum oxide formed during powder manufacturing. The products examined were manufactured from atomized powder containing

Jan 1, 1970

Jan 1, 1893

Established as a Division March 24, 1922 John R McMillan, '56, Chairman Claude R Hocott, '55, Past Chairman Thomas C Frick, '56, Vice-Chairman D W Akins, '57, Vice-Chairman Joe B Alford, Executive Secretary 800 Fidelity Union Building Dallas 1, Texas T A Pollard, Treasurer

Jan 1, 1954

Established as a Division March 24, 1922 R B Gilmore, '57, Chairman G L Yates, '56, Vice-Chairman Phil J Lehnhard, '56, Vice-Chairman John R McMillan, Past Chairman T A Pollard, Treasurer Joe B Alford, Executive Secretary 800 Fidelity Union Building Dallas 1, Texas

Jan 1, 1955

By C. D. Hall

This paper may be divided into two main parts: (1) analysis and data to show that Eq. 6 adequately correlates the authors' experimental data, and (2) the assertion that Eq. 20 "should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian, and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable pressure reductions." The authors might well recommend that this broad grouping of fluid types could be correlated by using Eq. 6 (requiring data from at least two pipe diameters). On the other hand, Eq. 20 is only shown to be adequate for conditions within the range of the present data set. Specifically, predictions by Eq. 20 for diameter scale-up to casing sizes would give larger deviations than implied in Table 2, and scale-up for some other fluids that give large drag reduction could be grossly in error. The description of a class of fluids "which produce a diameter family of straight parallel lines on a log (d?p/4L) vs log (8 v/d) plot. . ." defines a necessary condition for using Eq. 6; i.e., that s shall be constant for each fluid. The proposal that Eq. 20 is applicable to turbulent flow of such fluids is equivalent to saying that the spacing of these parallel lines, with A being constant, will be found to correspond to m = -1.20 for all such fluids. Table 1 shows the values of m derived from data on 16 non-Newtonian fluids. The key statement of this paper is that the diameter exponents "do not vary significantly from . . . -1.20." In statistical terms, this says that the m value for each fluid, which was obtained from all the measurements made on that fluid. has not been shown to be different from the arithmetic mean of the m values for the 16 fluids tested. This implies that the group mean, -1.20, is a more reliable value to use for an individual fluid than is the m value derived from the data on that fluid alone. No statistical test is described to support the key statement that the diameter exponents do not vary significantly from -1.20. Such a test would have to take into account that each individual m value is shown to correlate the pressure gradients for its fluid, with only about 3 percent standard deviation over the diameter range covered. That is, the m value is not the result of a single independent measurement. Thus, it would not be sufficient, or valid, to compare the deviation of one of the m values with the variance of the 16 values of m about their mean. An alternative interpretation of the key statement is that the diameter exponents do not vary appreciably from -1.20; i.e., that using -1.20 does not cause serious inaccuracy. Table 2 seems to be offered in support of such an assertion. However, such a statistical treatment (1) is unnecessary and (2) cannot lead to any valid scale-up generalization. The amount of error introduced by using a 1"wrong" value of diameter exponent — i.e., -1.20 instead of m — is determined by Eq. 6. The ratio of the pressures predicted by Eqs. 6 and 20 for scale-up from ds in small pipe to d, in casing is The pressure for 30-percent calcium carbonate slurry (m = -1.112) in 10-in. ID pipe would be predicted 30 percent higher by Eq. 6 than by Eq. 20, if based on tests in 0.5-in. ID pipe. The data set tested in Table 2 represents only a limited sample of pipe diameters (ratio of about 4:l) out of the population of diameters that would

Jan 1, 1970

By I. W. Walling, F. B. Plummer

Bastin and others have demonstrated the presence of sulphate-reducing bacteria in oil wells producing salt water. Analyses show that at 125°F. bacteria alone reduce sulphates in East Texas salt water by only 3 per cent in 30 days, forming principally hydrogen sulphide and sodium or calcium hydroxide. The hydrogen sulphide reacts with soluble iron compounds to produce iron sulphide in the absence of oxygen, and ferric hydroxide where oxygen and air are present. Where iron or other metals and iron sulphide are already in the water containing bacteria, I00 per cent reduction of the sulphates is complete in 30 days or less; where magnesium is present, reduction is complete in 15 days. The effects of changes in temperature, of different bactericides, and of concentration of bactericides on sulphate reduction are described in detail and illustrated by tables and curves. The significance of sulphate reduction on corrosive properties of oil-field water is briefly discussed. Chemistry of East Texas Oil-field Water The chemical composition of the water in the East Texas field salt-water disposal pits is shown in Table I. This salt water corrodes pipes, pumps, and steel tanks excessively, principally because of its content of oxygen, hydrogen, sulphide, and carbonic acid. The carbonates in the water when exposed to air tend to give up carbon dioxide and to precipitate calcium carbonate in large quantities. This forms coatings in tanks, settling pits, and ditches, and soon, unless removed by acid treatment, will effectively clog an injection well and reduce the flow of water back into the ground. The iron compounds in the water, most of which are dissolved from tanks and pipes, are in the ferrous form, and when exposed to the air are oxidized from soluble ferrous carbonate to insoluble ferric hydroxide, resulting in the precipitation of a gelatinous precipitate that will clog oil-field sands effectively: 2Fe(HCO3)2 + O + H2O -> 2Fe(OH)3 + 4CO2 The sulphates in strong sulphate-bearing water may be attacked by swarms of sulphate-reducing bacteria and more hydrogen sulphide may be produced. The hydrogen sulphide reacts with soluble minerals in the water to form black sludges. A knowledge of the chemistry of each reaction in oil-field water is important to the oil-field engineer, since means must be devised to prevent the formation of harmful precipitates that clog injection wells and to prevent corrosion of tanks by harmful products of biochemical processes. Methods of Treating Water before Injection into Ground* The open system of handling the waste salt water in the East Texas field consists of aerating and chemically treating the water to precipitate the unstable iron,

Jan 1, 1946