Search Documents

By AIME AIME

ATER the preliminary registration at which approximately 380 members and guests were registered, the 138th meeting of the Institute was opened in the Concert Room of the Palace Hotel. E. A. Hersam, chairman of the San Francisco Section, voiced a brief welcome and introduced F. W. Bradley, president of the Institute, who presided over the remainder of the morning session. After expressing the welcome of the Institute to the members and guests, he read a telegram from Secretary H. Foster Bain, extending the best wishes of the eastern staff and members for a successful meeting. He next introduced Theodore J. Hoover, dean of the School of Engineering, Stanford University, who read an address by the Secretary of the Interior, Ray Lyman Wilbur, briefly outlining California's part in the mining industry and giving the welcome of California to this meeting of the Institute.

Jan 1, 1929

By Paul H. Johnson

Chemical mining may be defined as the use of chemicals in extracting metal values from in situ broken or unbroken ores within a mine. The present means for the generation and regeneration of sulfuric acid or sulfuric-ferric sulfate solutions are inadequate for most applications. This report describes a pressure oxidation process for the generation and regeneration of these solutions from pyrites and spent iron sulfate leach liquors. While recent mining developments such as solution injection, caving, and conventional and nuclear blasting, have provided new and better means for the per-colation of leach solutions through rock masses, little has been done to reduce cost and improve the quality of the leach solutions that are required. A leach solution for chemical mining should meet certain requirements. It should be 1) inexpensive on either a small or large tonnage basis, 2) capable of selectively leaching the desired ore minerals contained in a particular ore, 3) of the proper strength or quality to do the job of leaching in an underground environment and 4) amendable to simple and inexpensive metal recovery steps. It is also important that the capital investment be low for the solution generation and; or regeneration plant.

Jan 8, 1965

Discussion of the paper of ALBERT D. BROKAW, to be presented at the Colorado meeting, September, 1915, and printed in Bulletin No. 1:16, April, 1918, pp. 947 to 950. LEE HAGER,* Houston, Tex. (written (discussion t).-In no other oil region of the world, perhaps, have the geological principles, of such high value in many fields, found so little practical application as in the

Jan 8, 1918

By W. R. Ingalls

In choosing the unusual title given to this paper, in which the term "cyclic " might be substituted for "intermittent," my idea has been simply in respect of precision. We might say old method vs. new method, but that antithesis implies something of substitution that has not occurred and perhaps is not in sight. We may say horizontal retorts vs. vertical, but none of the older retorts are truly horizontal, and there are three different types of vertical retorts. Other complexities might be suggested. There is, however, a broad distinction between distilling that is accomplished in a periodic cycle, generally daily; and distilling that is accomplished continuously, irrespective of whether it be done in the vertical retorts of the New Jersey process or in the retorts of the Trollhät-tan process. In offering a summary of the present state of the art with the intermittent process, I shall not have any idea of exemplifying it through descriptions of any single plants, but shall rather divide among the main steps of the process and outline what is best developed among them. In pursuing this thought, it will manifestly be impossible to make a composition that will exemplify the acme of good practice, for the latter will always be a function of the cost of labor, fuel, etc., which are widely variable. As of 1929, in respect of labor we might generalize the average plant wage in the Pittsburgh-Wheeling district of the United States at $5 per day; in Oklahoma at $3; in Great Britain at $3; in Germany at $1.75-$2; in Belgium and France at $1. With high labor costs the metallurgist will naturally use means of the nature of mechanization that with low labor would be uneconomical when capital charges are taken into account. Nor may we from records of performance safely make positive deductions in respect of the efficiency of different types of furnaces unless they have been tested comparatively under identical conditions in the same works. We shall find gas-fired regenerative furnaces showing coal consumption from 1.2 tons down to 0.7 per ton of roasted ore, which may be ascribable to difference in the thermal value of the coal that is used or to differences in proportions of the parts of the furnace, which is something quite distinct from the principle of the furnace. Thus, we have

Jan 1, 1937

By A. D. Rovig, T. J. Fisher

By converting its autogenous mills to steel ball mills at the C. E. Weed concentrator in Butte, Mont., The Anaconda Co. has achieved substantial increases in through- put tonnage, plus better recoveries as a result of the finer feed size to subsequent flotation operations. If steel grinding is so superior to autogenous grinding, why wasn't it chosen in the first place? Briefly, here's why:

Jan 10, 1975

By John D. Sullivan, Chester R. Austin, Edwin J. Rogers

The problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce lightweight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough qo that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an - outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, partitularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating."² The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the Purpose Of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

The problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce lightweight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough qo that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an - outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, partitularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating."² The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the Purpose Of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By Frank Harwood Riddle

Products made from the ores of the sillimanite group, and synthetic substitutes for them, have unique properties, and service tests prove that they are playing, and will continue to play, a major part in improvements in metallurgical processes. Also, they are examples of how comparatively useless, rare, or "museum" minerals have been made available in commercial quantities. Until research developed uses for them, the minerals had been observed only in small, scattered masses, or crystals. Improvements in ceramic processes and compositions have come about very gradually. In the last 10 or 15 years, several outstanding developments have been made. Of greatest interest to the mining and metallurgical engineers are those affecting the composition, necessitating the mining of new minerals, and improvements in ceramic products used in metallurgical processes. Sillimanite and Mullite Sillimanite (Al2O3.SiO2), then known as Fibrolite, according to Dana,' was first reported in 1792. In 1796, cyanite (Al2O3.SiO2) was first described.2 In 1873, Behrens published results of his microscopic study8 of porcelain. He showed that it contained what appeared to be crystals, which dissolved less readily than quartz and glass in hydrofluoric acid. Hussak4 described the presence of needlelike crystals as occurring in some instances in small amounts in certain porcelains. In 1908, Plenske and Zoellner both studied porcelain structure.5 Plenske observed that "sillimanite" might be present in masses of exceedingly minute grains which apparently were amorphous. Zoellner advanced the theory that the needlelike crystals were formed by a molecular change in the clay,

Jan 1, 1932

By J. B. Clark

The oil industry has long recognized the need for increasing well productivity. To meet this need, a process is being developed whereby the producing formation permeability is increased by hydraulically fracturing the formation. The "Hydrafrac" process, as it is now being used, consists of two steps: (1) injecting a viscous liquid containing a granular material, such as sand for a propping agent, under high hydraulic pressure to fracture the formation; (2) causing the viscous liquid to change from a high to a low viscosity so that it may be readily displaced from the formation. To date the process has been used in 32 jobs on 23 wells in 7 fields, resulting in a sustained increase in production in 11 wells. INTRODUCTION Need For Process Although explosives, acidizing, and other methods have long been used, there still exists a need for artificial means of improving the productive ability of oil and gas wells, particularly for wells which produce from formations which do not react readily with acids. This paper discusses the development of a hydraulic fracturing process, "Hydrafrac", which shows distinct promise of increasing production rates from wells producing from any type of formation. The method is also considered applicable to gas and water injection wells, wells used for solution mining of salts and, with some modification, to water wells and sulphur wells. Requirements of Process In considering such a possible process, it appeared that certain requirements must be met. Some of these are as follows: A. The hydraulic fluid selected must be sufficiently viscous that it can be injected into the well at pressure high enough to cause fracturing. B. The hydraulic fluid should carry in suspension a propping agent, such as sand, so that once a fracture is formed, it will be prevented from closing off and the fracture created will remain to serve as a flow channel for oil and gas. C. The fluid should be an oily one rather than a water-base fluid, because the latter would be harmful to many formations. D. After the fracture is made, it is essential that the fracturing fluid be thin enough to flow hack out of the well and not stay in place and plug the crack which it has formed. E. Sufficient pump capacity must be available to inject the fluid faster than it will leak away into the porous rock formation. F. In many instances, formation packers must be used to confine the fracture to the desired level, and to obtain the advantages of multiple fracturing. Development of Process As a necessary step in the development of this process, it was deemed advisable to determine if the Hydrafrac fluids were actually fracturing the formation or whether these special fluids were merely leaking away into the surrounding formation. To determine this, a shallow well, 15 feet deep, was drilled into a hard sandstone. Casing was set, the plug drilled, and the well deepened in the conventional manner. A fracturing fluid dyed a bright red was used to break down the formation. Sand mixed with distinctively colored solids was injected into the well with the fracturing fluid to prop open any fracture made in the formation. A simulated gel breaker solution dyed a bright blue was then pumped into the well to determine if the gel breaker would follow the first solution. The results are shown in Figure 1. It was noted that a fracture was formed about the well bore, that the propping agent was transported back into the break, and that the breaker solution did actually follow the fracturing gel out into the fracture. While it is realized that this shallow well test is probably not exactly equivalent to a deep test, the results were interpreted as being a definite indication of what happens down the hole during a Hydrafrac job. Of interest in this connection is an investigation reported by S. T. Yuster and J. C. Calhoun, Jr.' This study, re~orted after the Hydrafrac work was under way, presents some excellent field data supporting the theory of fracturing a formation with hydraulic pressure. METHOD Steps of Hydrafrcu: Process Figure 2 shows a simplified cross-sectional view of a well treated by one version of the process. The first step, formation breakdown, is done with a viscous fluid, usually consisting of an oil such as crude oil or gasoline, to which has been added a bodying agent. Due to availability and price, war-surplus Napalm has been used in the majority of experiments to date. Napalm is the soap which was used in the war to make "jellied gasoline". The next step consists of breaking down the viscosity of the gel by injecting a gel-breaker solution and then after several hours, putting the well back on production. Figure 3 shows diagram-matically, a typical field hookup. The oil or gasoline is unloaded into the 10 bbl. tank shown on the left rear of the truck. This base fluid is picked up by the mixing pump and pumped through the jet mixer, where the granular soap is added. Next it goes into a small mixing tub, from which the high-pressure pump takes suction. The solution is then pumped into the well. The breaker solution is then taken from an extra tank and is displaced into the well immediately following the gel. When required, additional trucks may

Jan 1, 1949

By J. B. Clark

The oil industry has long recognized the need for increasing well productivity. To meet this need, a process is being developed whereby the producing formation permeability is increased by hydraulically fracturing the formation. The "Hydrafrac" process, as it is now being used, consists of two steps: (1) injecting a viscous liquid containing a granular material, such as sand for a propping agent, under high hydraulic pressure to fracture the formation; (2) causing the viscous liquid to change from a high to a low viscosity so that it may be readily displaced from the formation. To date the process has been used in 32 jobs on 23 wells in 7 fields, resulting in a sustained increase in production in 11 wells. INTRODUCTION Need For Process Although explosives, acidizing, and other methods have long been used, there still exists a need for artificial means of improving the productive ability of oil and gas wells, particularly for wells which produce from formations which do not react readily with acids. This paper discusses the development of a hydraulic fracturing process, "Hydrafrac", which shows distinct promise of increasing production rates from wells producing from any type of formation. The method is also considered applicable to gas and water injection wells, wells used for solution mining of salts and, with some modification, to water wells and sulphur wells. Requirements of Process In considering such a possible process, it appeared that certain requirements must be met. Some of these are as follows: A. The hydraulic fluid selected must be sufficiently viscous that it can be injected into the well at pressure high enough to cause fracturing. B. The hydraulic fluid should carry in suspension a propping agent, such as sand, so that once a fracture is formed, it will be prevented from closing off and the fracture created will remain to serve as a flow channel for oil and gas. C. The fluid should be an oily one rather than a water-base fluid, because the latter would be harmful to many formations. D. After the fracture is made, it is essential that the fracturing fluid be thin enough to flow hack out of the well and not stay in place and plug the crack which it has formed. E. Sufficient pump capacity must be available to inject the fluid faster than it will leak away into the porous rock formation. F. In many instances, formation packers must be used to confine the fracture to the desired level, and to obtain the advantages of multiple fracturing. Development of Process As a necessary step in the development of this process, it was deemed advisable to determine if the Hydrafrac fluids were actually fracturing the formation or whether these special fluids were merely leaking away into the surrounding formation. To determine this, a shallow well, 15 feet deep, was drilled into a hard sandstone. Casing was set, the plug drilled, and the well deepened in the conventional manner. A fracturing fluid dyed a bright red was used to break down the formation. Sand mixed with distinctively colored solids was injected into the well with the fracturing fluid to prop open any fracture made in the formation. A simulated gel breaker solution dyed a bright blue was then pumped into the well to determine if the gel breaker would follow the first solution. The results are shown in Figure 1. It was noted that a fracture was formed about the well bore, that the propping agent was transported back into the break, and that the breaker solution did actually follow the fracturing gel out into the fracture. While it is realized that this shallow well test is probably not exactly equivalent to a deep test, the results were interpreted as being a definite indication of what happens down the hole during a Hydrafrac job. Of interest in this connection is an investigation reported by S. T. Yuster and J. C. Calhoun, Jr.' This study, re~orted after the Hydrafrac work was under way, presents some excellent field data supporting the theory of fracturing a formation with hydraulic pressure. METHOD Steps of Hydrafrcu: Process Figure 2 shows a simplified cross-sectional view of a well treated by one version of the process. The first step, formation breakdown, is done with a viscous fluid, usually consisting of an oil such as crude oil or gasoline, to which has been added a bodying agent. Due to availability and price, war-surplus Napalm has been used in the majority of experiments to date. Napalm is the soap which was used in the war to make "jellied gasoline". The next step consists of breaking down the viscosity of the gel by injecting a gel-breaker solution and then after several hours, putting the well back on production. Figure 3 shows diagram-matically, a typical field hookup. The oil or gasoline is unloaded into the 10 bbl. tank shown on the left rear of the truck. This base fluid is picked up by the mixing pump and pumped through the jet mixer, where the granular soap is added. Next it goes into a small mixing tub, from which the high-pressure pump takes suction. The solution is then pumped into the well. The breaker solution is then taken from an extra tank and is displaced into the well immediately following the gel. When required, additional trucks may

Jan 1, 1949

By G. D. Hobson, I. Mrosovsky

Material balance relationships for expansion-type reservoirs above the bubble point have been discussed in recent years by H. N. Hall and M. F. Hawkins, Jr. The former drew attention to the effects of rock compressibility, and the latter to the effects of the compressibility of any interstitial water. Hawkins derived a general relationship which took note of oil, water and rock compressibilities, and then by assuming first, the absence of interstitial water and secondly, no effects due to interstitial water or rock compressibility, obtained relationships symbolically of the same form as those previously derived directly by Hall. Hawkins defined his terms clearly, and noted an approximation, due to the omission of a term involving the product of two compressibilities, made in reaching his final equation. There is, however, possible ambiguity with regard to Hall's written definition of the oil production term. One interpretation would mean that the produced oil and initial oil-in-place, if both required as stock tank barrels, would be obtained by using different formation volume factors in the conversion in order to satisfy the conditions implicit in Hall's formulae. The other would involve an approximation which, if used, was not stated. In both Hall's and Hawkins' studies the effect of the approximation or inconsistency is very slight. Nevertheless, it may be justifiable to give a somewhat more consistent derivation, since the complexity of the final relationships is not thereby greatly increased. Let the initial pore volume be Vi and the volume after a pressure drop of Ap, V. Then V = V, (1 - ?p . cr), where c, is the rock compressibility expressed as change in pore volume/unit pore volume/unit pressure change, and is defined with the initial pressure as base. Suppose that the interstitial water saturation under the initial conditions is Sw. The total volume of interstitial water under those conditions will be ViSw. If the volume of the water after dropping the pressure by ?p is V., this will be given by Vw = ViSw (1 + ?p.c,w), the compressibility of the water being c, which is ex- pressed using the volume at the initial pressure as base. If Boi is the reservoir volume factor of the crude oil for the initial reservoir conditions, and B. the equivalent factor when the pressure has dropped by ?p, with N the initial amount of oil expressed as stock tank barrels. N.Boi = Vi - V,Sw If n is the amount of oil produced (in terms of stock tank barrels) as a result of the pressure drop ?p, the remaining subsurface volume of oil at the lower pressure will be Bw, and Bc can be related to the compressibi:ity of oil and the pressure drop, and if c, is the compressibility factor based on the initial conditions, The relationship derived by Hawkins was case to a standard at the lower pressure, while a term (Ap) had been dropped, because of its smallness arising from its dependence on the products of two compressibility factors. When there is no interstitial water and rock compressibility can be ignored, Eq. 1 reduces to:

Jan 1, 1957

By Theodore Hatch

The pneumatic rock drill operates essentially as a crusher. The rock is shattered into a powder that is removed from the drill hole by the air stream introduced through the hollow drill steel. Particles thus produced vary in size from 1/4 in. or larger down to diameters too small to be revealed by the ordinary microscope. The power consumed by the drill is proportional to the new surface area of the powdered material, therefore the greater the proportion of "dost" produced, the higher the power consumption and the lower the drilling speed. A considerable amount of material ejected from the hole settles on the rock and much of this falls back as the mound builds up to be crushed further before it is removed again. The cushion of dust at the bottom of the hole reduces the effectiveness of the blow of the bit and thus lowers the rate of drilling. The unfavorable working conditions created by the dust also reduce the drilling speed by lowering the efficiency of the operator. Thus, the dust produced by rock drills constitutes a serious drawback to economical performance on all drilling operations. To the economic objections, one must add the more important objection to the health hazard created when the dust contains free silica (quartz). The silicosis problem is a familiar one in many mines, tunnels, and other underground operations as well as in quarries and other types of open rock excavation. Dust is a necessary end product of all pneumatic drilling operations. Its production cannot be eliminated although the proportion of microscopic particles can be reduced by using improved drill steel, proper methods of sharpening, more efficient drills, etc.—improvements that increase the drilling speed largely by increasing the size of the cuttings. The absolute improvement secured in this way is not great, however, and the pneumatic drill must always remain a dust-producing machine. Definite benefits do result, on the other hand, from the use of dust-control equipment that captures the dust as it emerges from the hole and conveys it to a remote point of discharge. Dust production continues, but dust dispersion into the atmosphere is prevented. The dust is removed as rapidly as it is formed, with the following results: (I) The silicosis

Jan 1, 1937

By H. N. Eavenson

The eleven mines of the United States Coal and Coke Co. in the Pocahontas coal field are situated in McDowell County, W. Va., which is a mountainous region. The valleys rarely exceed 200 ft. (60 m.) in width, the hillsides slope from 25°to 33°, and the tops, from 600 to 900 ft. above the valleys, carry practically no level land. At least 80 per cent. of the area is covered with timber. All the workings are drift mines; and while the average grades of the seams worked are ample for drainage, local dips and swamps necessitate the use of a large number of local pumps or of numerous drainage ditches to keep the mines free from water during heavy rains. The water handled in any mine is not great, compared with the coal output, and usually causes little trouble except during extremely wet periods. In new workings, the water encountered, except in rare cases, is trifling; it is only after rib drawing has started and the surface has been broken that water troubles begin. The strata overlying the coal are sandstone, shales, and slates; as the soil is thin and sandy, it does not tend to puddle and stop the cracks, which remain open for a long time. As mining progresses and the robbed area increases, the broken area becomes larger, increasing the openings into the mined territory. The cover over the robbed portions of the mines varies from 30 to 750 ft. (9 to 228 m.). When the ground is saturated, considerable water finds its way into the mines the day after a heavy rainfall and for three or four days it tends to fill the low places, wash the tracks, etc. and unless from three to four times as many pumps are installed as are normally needed, considerable output is lost. In most cases the water will flow from the mines, and the obvious solution is to provide drainage ditches of ample size to carry the maximum flow expected, so that the inflow will have no opportunity to flood the working places. Laying out the drainage headings on the proper average grades was an easy matter but where blasting was necessary to provide uniform grades, as was frequently the case, it was important that the maximum flow to be expected and the size of ditches to be provided should be known so that only rock work necessary to provide proper drainage

Jan 1, 1922

By Guillermo V. Borquez

INTRODUCTION The basic factors that influence the selection of a mining method are the geometry of the ore deposit and the strength of the ore and surrounding rock. These factors usually determine the ore recovery and dilution of the deposit under analysis. For the purpose of this paper we will consider a generalized case of a block caving system and the sequence of the analysis needed to optimize ore recovery. The analysis presented is intended for the preliminary planning stage. The critical factors involved in the caving process are identified and the methods for evaluating the suitability of a particular deposit to the caving method of mining are outlined. The mine design is approached by identifying the two most important, dimensions: the size and spacing of the draw points. These dimensions are estimated from a simulation model which takes into account the ore recovery, the incremental value of the ore recovered, and the safety conditions of the operations. The model estimates the number of draw points required to extract efficiently and safely the broken ore from the caving area. This number is found in the range where the net incremental value of the ore is maximized and the probability of pillar failure does not exceed the limit which is acceptable for a safe mining operation. A mining method and its design are in a continuous process of optimization. This process is unique for each deposit because of the many parameters involved; therefore, a back analysis of the operations should be performed when possible. These analyses will indicate if the ore body responds in a predictable manner to the parameters contained in the geological, fragmentation, and draw point models. SELECTION OF ALTERNATIVE MINING METHODS The selection of a mining method best suited to define the minable ore reserves of a given deposit involves consideration of the geometry of the ore deposit and the strength of the ore and surrounding rock. These two factors are usually sufficient to determine the ore recovery and dilution of the deposit. After analyzing the geological reserves and defining the limits of the deposit, either an open pit or an underground mining method can be selected to define the minable ore reserves. The sequence of steps to follow in the selection of a mining method is presented in Figure I. From an economic point of view, the strip- ping ratio is the determining factor for the selection between an underground or open pit method. In turn, the stripping ratio is a function of the grade distribution and con- figuration of the ore body. In order to obtain a preliminary estimation of the stripping ratio, a parametric analysis could be applied, such as the approach used by Professor E. P. Pfleider (1972) and summarized in Table 1.

Jan 1, 1981

By E. A. Holbrook

MINING Metallurgy, and Petroleum Engineering department in our colleges are facing a crisis; indeed, conditions that threaten their very existence. Unless the Army, Navy, and War Manpower Commission change their present policy, within two years mineral industries education as now carried on will die, because no ablebodied students will be left in the course. If this is the decision of our responsible governmental agencies we of the mining schools must perhaps accept it as a war measure. It might be well however, for the executive of our mining metallurgical, and oil companies to look ahead a, to where they are to recruit a supply of young technically trained engineers. You can no more operate a mine, a steel plant or an oil company without trained engineers than you can operate a battleship without mechanical and electrical engineers.

Jan 1, 1943

By D. I. Bardos, Paul A. Beck

The 1100°c isothermal, sections of the V-Fe-Si, V-Co-Si, and V-Ni-Si systems were studied at silicon contents between 0 and 40 at. pct. The single-phase fields in the 30 and 50 at. pct Mn sections of the 1100°C tetrahedron of the V-'Wn-Fe-Si system were also determined. The direction of extension of the elongated O, R, D, and a-Mn Phase fields suggests that the stability of these phases is determined largely by the electron concentration. The peculiar shape of the above ternary a phase fields, as well as of the a phase fields in the V-;Mn-Si and Cr-MTZ-Si systems is accounted for on the assumption that in manganese-(iron-, coball-, nickel-) rich alloys silicon atoms do not exclude d electrons , while in alloys low in the above components they do. This assumption also leads to the expected electronconcentrations for q and ß-Mn phases formed by transition metals with aluminurn. In earlier work it was shown that in ternary alloy systems of transition elements the a a and certain other phases with complex structure, such as the p and R phases,3 form elongated phase fields extending in a direction corresponding to a constant electron concentration. Recently similar behavior was observed in manganese-rich ternary ß-Mn solid solutions with another transition element and with silicon, germanium, or tin,4 confirming earlier indications3 that ß-Mn is also an electron phase. The alloying behavior of silicon in these manganese-rich alloys sug- gested that the four outside electrons of silicon participate in the bonding and that the predominantly d-like bonding electrons are not excluded from the silicon sites. Presumably, some of the normally unoccupied 3d states associated with the silicon atoms are in these alloys lowered to the Fermi level;4 thus silicon behaves as if it, too, were a transition element. The manganese-rich boundary of the a phase in the V-Mn-Si system,4 as well as in the Cr-Mn-Si sys-tem,4,5 extends approximately parallel to the ß-Mn phase boundary, corresponding to the transition ele-mentlike behavior of silicon described above. However, at lower manganese contents (i.e., in the high-vanadium or -chromium region) the a phase field in both ternary systems mentioned extends in a direction roughly perpendicular to that of its manganese-rich boundary, a phenomenon that is apparently inconsistent with the behavior of silicon in the manganese-rich alloys. A similar, although somewhat less pronounced, extension of the a phase occurs also in the high-vanadium (low-iron) region of the V-Fe-Si system at 1175C, but reportedly not in the V-Co-Si or V-Ni-Si systems at the same temperature.5 The present work was undertaken to investigate in more detail the extension of the a phase (as well as of other electron phases that may be present) in the last three systems and to elucidate this phenomenon, which has not been satisfactorily explained previously. EXPERIMENTAL PROCEDURES Most of the alloys were melted in an arc furnace, using a water-cooled copper crucible under helium atmosphere. The transition metals were of better than 99.9 pct purity and the silicon used was 99.98 pct pure. Alloys containing less than 20 pct V were induction-melted in recrystallized alumina crucibles under argon atmosphere.

Jan 1, 1967

By J. B. Scott, J. L. Popham, H. F. Coffer, J. J. Reynolds

This paper concerns field experiments to define the areal extent, orientation and thickness of an artificial fracture in the Sacatosa field, Maverick County, Tex. The fracture was made by a sand-oil treatment of 176,-000 gal of lease crude containing a fluid-loss additive and 270,000 lb of 20-40 mesh subangular Poteet sand. The well was perforated with a jet gun, consisting of six shots in a single plane. Fourteen test holes were drilled at various locations around the fractured well. Drill-stem tests, Micro and Sonic Logs, coring and sampling of formation cuttings were used to determine the presence of the fracture in these holes. The test holes were drilled at distances up to 250 ft in a radial pattern around the fractured well. In addition to fracture areal extent and orientation, sand grain size before and after fracturing, erosion of perforations and fracture thickness were studied. INTRODUCTION The orientation,12 areal extent3, 4 and thickness5-9 of artificially induced fractures in reservoir rock by hydraulic means have been discussed in great detail in the oil industry in recent years. Methods for initiating vertical"' and horizontal" fractures have been tested in the laboratory and the field. Although the methods used give successful well stimulation, good field data on the physical characteristics of the fracture are lacking in the literature. It is recognized generally that properties of a fracture, such as thickness, sand placement in the fracture" and shape, may vary from reservoir to reservoir. This paper gives data on size, orientation and sand placement in a large fracture initiated in a single plane in Sacatosa field, Maverick County, Tex. It is not intended as a speculative study; rather, it is restricted to actual field data on fracture properties. No attempt is made to prove that the same type of fracture occurs in all wells. The field procedure was to drill 14 test holes at various locations around the fractured well. By employing several different testing techniques, the presence of the fracture and some of its characteristics were determined. These techniques as well as the results obtained are discussed in detail in this paper. DESCRIPTION OF FRACTURE TREATMENT N. J. Chittim Well No. 37-1, completed in the San Miguel No. 1 sand, Sacatosa field, Maverick County, Tex., was chosen for the field study. The San Miguel sand is a tight, well consolidated sandstone with an average porosity of 23 per cent. The permeability ranges from 0.1 to 10 md, with a median permeability of 2.3 md. The sand thickness averages 23 ft and is located at depths of 1,150 to 1,700 ft throughout the field.I3 The fracture treatment performed on Well 37-1 was as follows. 1. The well was drilled to a depth of 1,438 ft with native mud, and 51/2-in. casing was set and cemented to the surface. 2. The casing was perforated at 1,349 ft with a fracture-initiating jet gun. This gun consists of six shots, 7/16-in. diameter in a single horizontal plane. The jets were oriented in two groups of three, 180" opposed. The perforating device was designed to initiate a fracture perpendicular to the wellbore.

By Erwin S. Sperry

Some time ago, the author had occasion to make an alloy of equal parts of nickel and aluminum, for the purpose of adding small amounts of nickel to pure aluminum. The nickel was melted in a plumbago crucible under a layer of borax ; and at a proper temperature the aluminum was added, and the whole mass was stirred with a plumbago stirrer. The alloy immediately became incandescent and boiled. It was then poured into iron moulds, in the form of ingots weighing about 10 pounds. The metal when poured was very fluid and free from the viscosity so often noticed in nickel and nickel-alloys. The color of the alloy is gray, not unlike that of wrought-iron, and the fracture is devoid of any crystalline appearance. It is quite brittle, and can be readily ground to a powder in a mortar. More metal was made than was needed; and what remained unused was placed in a covered wooden box and set away. In about three months, as it mas again necessary to use the alloy, the box was opened; and, much to my surprise, nothing but a dark gray powder was found in it. This condition of the alloy could not be accounted for. An attempt was made to melt the powder and pour it again into ingots, but with negative results. Analogy pointed to disintegration; and it was decided to make a fresh sample of the alloy, and watch the material from the beginning. In the second experiment the conditions were identical with those of the first, with the exception that fluor spar was substituted for the borax. This change was made because it was thought that perhaps the borax might have been

Jan 1, 1900

David THOMAS 1871 R. W. RAYMOND 1872-1874 A. L. HOLLEY 1875 ABRAM S. HEWITT 1876 T. STERRY HURT 1877 ECKLEY B. COKE 1878-1879 WILLIAM P.SHINN 1880 WILLIAM METCALF 1881 RICHARD P. ROTHWELL 1882 ROBERT W. HUNT 1883 JAMES C. BAYLES 1884-1885 ROBERT H. RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B. POTTER 1888 RICHARD PEARCE 1889 ABRAM S. HEWITT 1890 JOHN BIRKINBINE 1891-1892

Jan 1, 1929

By Walter White

THE measurement of the reading of a thermoelement is the measurement of an electromotive force extraordinarily small compared to those generally used in commercial work. Of the various possible methods of measuring such a quantity, the most advantageous is always a delicate galvanometer. Since a galvanometer measures current, it is necessary to adopt some scheme by which its current reading shall indicate electromotive force. There are two general methods of doing this. One is to use the delicate galvanometer as a "direct reader," that is, to let the electromotive force of the thermoelement furnish the power and produce the current measured. If the resistance is constant the reading will, after a suitable calibration, give the electromotive force of the thermoelement which, by means of a table or of a suitable scale in the galvanometer itself, will FIG. 1.-SIMPLIFIED POTENTIOMETER. POTENTIAL DROP ACROSS THE PART PIN or CIRCUIT OF BULL CELL BALANCES THAT OF THERMOELEMENT TC WHEN GALVANOMETER G READS ZERO. give the temperature. The other method, that of the potentiometer, is to balance the electromotive force of the thermoelement by means of another electromotive force, using the galvanometer to tell when the balance is made. The usual way of getting this other electromotive force is to have a battery, the "bull" cell, send a current through a series of resistances, which 'may in a special case be the resistance of a single wire. The fall of potential along this circuit will then, by Ohm's Law, be proportional to the resistance; the potential difference between any two points, proportional to the resistance between the two points. This is represented in Fig. 1, where M and N are the two points in the circuit AZ of the battery. If M or N, or both, is movable so that the resistance

Jan 9, 1919