Search Documents

By J Mauk, R Ruddock

The Taharoa ironsand deposit is 1600 hectares in size and is located 144 km south of Auckland on the west coast of the North Island, New Zealand. The sand predominantly contains heavy mineral-rich sediments, quartz, and feldspars. One hundred and two samples were collected from all areas of the mine, from the stockpile, black sand areas, tailings and Te Akeake Sands. Samples were collected with the primary focus on the next predicted mining path and secondly on gaining a good geographic spread throughout the mine. All samples were analysed for the dry, wet and particle density, the porosity and the magnetic, non-magnetic and clay minerals content.Stockpile samples had an average magnetic mineral content of 92 percent. Dry, wet and particle density values for stockpile material exceed all values from untreated ironsand samples with average values of 2.8g/cm3, 2.9g/cm3 and 4.4g/cm3 respectively. Black sand samples from the mine came from various areas such as the central area, the forest, the southern area and the benches. All black sand samples are remarkably consistent, with dry and wet density values between 2.3 û 2.5g/cm3 and particle densities that range from 3.7 to 3.9g/cm3. The porosity values are comparable to all other areas of the mine (average 37 per cent). The tailings and Te Akeake Sands have different physical properties due to their different mineral contents. The dry, wet and particle densities are all lower than that of all other areas with averages of 2.1g/cm3, 2.2g/cm3 and 3.3g/cm3 respectively. These lower values reflect the lower magnetic mineral content (average 18 per cent) and the associated increase in non-magnetic mineral content (average 78 per cent).

Jan 1, 2002

By J P. Evert

Didipio gold-copper mine operation is situated in the island of Luzon, approximately 270 km north of Manila in the Philippines, in an area of high seasonal rainfall. The hydrogeological water flow model implied that there would be high connectivity between regional structures and underground operations. This model predicted that underground mine groundwater inflows were expected to quickly rise as the decline progressed to a peak of 510 L/s. Designing a capital pump station to deal with 510 L/s has its own challenges, however developing the decline down to the required level, always dealing with 300 L/s of water and constructing the pump station is extremely challenging and required a robust water management plan and mine design. When dealing with expected high volumes of water, underground mine design and scheduling plays a key role in protecting electrical infrastructure, equipment, secondary pumps, and the decline from flooding. A good drainage system and controlled dewatering plan is essential for safety and progress. This paper details the dewatering techniques and mine designs required to accomplish decline development with high water inflows as used in the Didipio project. It will describe the learnings and outcomes that are achievable with a flexible design, as new structures are mapped, and water intersections are increased. It also highlights the potential for adaptability in mine planning to provide evolving improvements or to evade problems that are expected from the constant reconciliation of data recorded during development.

Mar 29, 2023

By DAVID C LAURENCE

The richer, shallower sapphire deposits of the New England region of New South Wales which have been traditionally mined by the small miner are almost worked out. Larger mining and exploration companies are replacing the small miner and exploring for the primary source of sapphire or lower grade alluvial deposits.Although in recent years considerable exploration effort has been directed at locating the primary source, commercial exploitation of sapphire is still restricted to the working of alluvial deposits.If the Australian industry is to compete against Asian and African producers it must use cost effective exploration, mining, processing and marketing methods.

Jan 1, 1990

ABSTRACT' Mainland Papua New Guinea is formed of a microcontinental / island arc system (?Eocene - latest Oligocene Sepic arc) which in Middle to Late Miocene times was obducted over the northward- moving Australian plate. The sedimentary and volcanic units of this system form part of the Wogamush Group (Aure beds, Mena beds, Omaura Formation, Movi beds, Wogamush beds, Wogamush Formation. Nansananka Conglomerate and other correlates in- eluding cale-alkaline volcanics and carbonate beds). This Sepic event was followed in Pliocene-Present times by the obduction of the Finisterre-Adelbert-Oenake fore-arc or possibly oceanic plateau. Obduction of the Sepic arc produced crustal thickening

Jan 1, 1997

By R H DAVIES

Peak Gold Mine is a new gold and base metal mining project being developed by Enterprise Metals (a 100 per cent subsidiary of CRA) at Cobar in the centre of New South Wales. The Cobar district has a long history of copper and gold mining operations stretching back to the 1870s. Extensive gold and base metal mineralisation was discovered at the Peak in 1981 below a series of gold mines which had been active around the turn of the century. Evaluation of the deposit through the 1980s led to CRA's decision to develop the project for production at a capacity of 450 000 tonnes per annum in late 1992. The project has been developed with a green fields approach despite the long history of mining in the local area. This approach has lead to several innovative ideas being trialed at the site which are expected to result in the operation being a low cost producer of gold and base metals.

Jan 1, 1992

A new approach to resource estimation at the exploration stage is emerging, based on the application of simple software techniques. The techniques combine the power of interactive graphics with proven database, analysis and estimation tools. With effective use of these tools the geologist now has maximum chance of deriving a reliable structural and grade model from the limited exploration data. Unlike cutoff-based polygonal methods, the resultant geological model can immediately be used to evaluate any economic scenario.These modelling techniques are embodied in MINEX-3D, an Australian software system. With the emergence of the 386-based PC and high resolution (VGA or better) graphics, MINEX-3D makes the power of this new 'desktop geological modelling' accessible to most exploration geologists.

Jan 1, 1990

This paper examines the cost and economic consequences of varying a number of key factors in the course of developing and operating new underground longwall coal mines with both shallow and deep cover in New South Wales. The economics of the project are assessed for the first 20 years of mine life using the discounted cash flow method with produc- tion and selling price being determined to provide break even costs for a range of minimum rates of return.

Jan 1, 1988

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

By J Dwyer, G Turner, D Pridmore, M Urosevic

Due to their ability to produce high-resolution images of the subsurface to great depths, seismic surveys provide critical inputs to almost all oil and gas exploration projects. However, with some notable exceptions, seismic surveys have rarely been used in mineral exploration. In the past, this was due to both technical and financial reasons. Significant developments on both fronts mean that seismic surveys can now offer substantial benefits to mineral exploration and mining, and surveys conducted for exploration can provide important data sets for mine planning over the life of a mining project.We present case history data that show that seismic surveys can greatly assist with mapping the 3D distribution of lithologies and alteration and, in favourable circumstances, directly detect mineralisation in and around mineral systems. As a result of their high spatial sampling density, seismic surveys are also highly effective at mapping structures that can remain undetected or poorly characterised by drilling alone. These structures may host or provide important vectors to mineralisation. They can also be particularly important when planning shafts, raise bores, declines, stopes and open pit walls. A further benefit of seismic surveys is that they can remotely provide information on geotechnical rock parameters that are used for rippability, slope stability, blasting and ground support.CITATION:Turner, G, Urosevic, M, Pridmore, D and Dwyer, J, 2015. Exploration and mining unified through seismic imaging, in Proceedings Third International Future Mining Conference, pp 117–122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Takeuchi T, Matsugaki K

We have developed a new shotcreting which is suitable for the primary support of TBM tun- nelling in soft rock. This spraying compound is made from cement, a special accelerating agent and glass fiber. It can be sprayed on to a rock surface using a specially designed gun similar to paint-spraying equipment. Some of the characteristics of this method are as follows: 1) If spraying is done keeping the distance between the gun and the rock surface be- tween 0.2 and 3.0 m, the rebound losses are small and there is little dust. 2) This method can be used on excavated rock surfaces under inflowing water conditions of up to 10 i/m2òmin. 3) After 1 day the compressive strengthes of the sprayed material is greater than 250 kgf/cm2.

Jan 1, 1987

By D Connelly

High purity alumina (HPA) is a processed, premium non-metallurgical alumina product characterised by its purity level ie 99.99 per cent (4N) or 99.999 per cent (5N). The market price, application, and performance of HPA varies widely according to its degree of purity. High purity alumina is a form of aluminium oxide (Al2O3) with growing use in LED lighting and coating on the ceramic cathode separator sheets in lithium ion batteries. This paper describes a study on producing high purity alumina from feldspar to produce HPA and potash for use as a fertiliser. The project was positive for a number of reasons. High potassium extraction (>99 per cent) was achieved in the alkali leach using sodium hydroxide as the leaching agent and full dissolution of the alkali leach residue was achieved using hydrochloric and sulfuric acid. The potential to produce a high purity alumina product via a complex but promising emerging process was assessed. The potential to extract potassium as potassium sulfate to add value to the project was also demonstrated with the test work.

Sep 1, 2024

By B Crowdey, J Wall

The particular underground operation relating to this paper is a gold producer and has an orebody predominately consisting of rhyolite and marcasites pyrite. The ore has been identified as being reactive to nitrates.Operations currently utilise two twin boom Tamrock™ Super-Drill Jumbos for development mining. Capital (waste) headings have a nominal size of 7 m wide × 6 m high, while ore headings are designed at 5 m wide × 5 m high, with the lower reaches of the mine narrowing down to a 4.5 m × 5 m design. Production drilling is currently undertaken with an Atlas-Copco L6 Solo. Due to the reactivity of the ore, inhibited emulsion phase bulk explosives are used for all blasting activities, with electronic detonators utilised in the production sequence.Sublevel shrinkage stoping is utilised when the orebody is stronger than the host rock. After blasting the ore, and during extraction, the surrounding host rock cannot maintain integrity and it ‘collapses’ on top of the ore. Gravity forces this collapsing rock to follow the blasted ore through the drawpoints.The highest risk involved with sublevel shrinkage stoping is the necessity for charge crews to work upon ‘rills’ at the drawpoints, which are occasionally unstable, to charge the next blast ring to be fired. To overcome this issue a loading technique called ‘precharging’ is used whereby two to three rings are charged, but only the first ring is fired. This technique can minimise risks by taking the charge crew away from the rill and brow.As this mine contains hot and reactive ground, strict guidelines from the Australian Explosives Industry and Safety Group Inc (AEISG) are adhered to. These guidelines relate to the sleep time for the precharged rings.This paper describes the issues faced with precharging in hot and reactive ground, the monitoring required and the systems and procedures that were put in place to enable a successful outcome.CITATION:Crowdey, B and Wall, J, 2014. Precharging sublevel shrinkage production rings in hot and reactive ground with electronic blasting systems, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Controlled Source Audio Magnetotelluric (CSAMT) surveys were carried out by Glass Earth (New Zealand) Limited (Glass Earth) in 2006 - 2007 to investigate epithermal gold targets in the central North Island of New Zealand. The surveys were conducted using a Zonge GDP 32 8-channels receiver and a Zonge XMT 32 transmitter powered by a 16 KW generator. The electric field dipole was maintained at 20 m length (five dipoles per 100 m spread) and the frequency ranged from 4 KHz to 4 Hz. Only scalar (TM mode) signals were recorded, using one magnetic coil per spread. The transmitter bipoles were 1 - 4 km in length and located about 5 to 10 km from each survey area.   Sixteen individual target areas were surveyed by June 2007. The CSAMT survey lines (100 - 400 m spacing) were determined mainly on results from previous ultra-detailed airborne magnetic and gravity surveys conducted by Glass Earth in 2005. The data from each CSAMT line was carefully examined to remove any spurious signals and processed using Zonge SCS2D software, which can produce smooth 2D resistivity inversions of the field data. The results were presented as resistivity sections and maps to help the identification of exploratory drilling targets, mainly from the existence of subsurface high resistivity zones (resistors) that can be interpreted as caused by silicification associated with epithermal mineralization.   An example of processing and interpretation of the CSAMT data is presented in this paper on results from Glass EarthÆs Tahunaatara target, where CSAMT surveys have identified zones of epithermal mineralization confirmed by exploratory drilling.

Jan 1, 2007

By R A. Pax

Electrostatic separation is a core requirement for the beneficiation of mineral sands suites to provide valuable product. Although the basis of electrostatic separation has been understood for some time, the details required to be able to calculate the metallurgical performance of a separator has not previously been achieved from a mechanistic perspective. Empirical models have had some success but require extensive test work. Traditionally, performance of an electrostatic separator is determined by careful experimental work using the target mineral suite. Although electrostatic separation was invented at the end of the 19th century, very little modification of the basic equipment occurred until relatively recently, with the addition of a plate electrode to aid separation. Previously, the author has presented results, calculated using finite element modelling (FEM), of the electric fields present in an electrostatic separator in various configurations. This paper will present some new mathematical modelling work, which uses the FEM determined electric field configurations but also incorporates some fundamental physical processes that provide insight as to the limitations and opportunities for this important separation technique.

Oct 5, 2011

By G Forbes, D J. Bradshaw, G S. Heinrich, D

Traditionally, operators on mineral flotation plants have relied on visual inspection of the froth surface when making adjustments to process set-points. Machine vision systems are being developed to relate froth surface descriptors, which can be consistently measured in real time, to flotation performance. By investigating the impact of various selected operating variables on both froth surface characteristics and metallurgical performance it is possible to develop a management strategy for the control and optimisation of the process. This paper presents the results of testwork conducted at Kennecott copper mine which investigates the relationship between the froth colour and the concentrate grade and discusses the factors which affect the froth colour. This work shows that the main factors that influence the froth colour in this system are molybdenum, copper and iron concentrate grade, pulp and concentrate per cent solids and pulp iron grade.It goes on to develop models to predict the concentrate grade based on colour information and velocity and stability information. It also shows that the most accurate prediction is made with combined colour and stability information.

Jan 1, 2005

By Christie AB, Bull VH

The geological environments of gold deposits are reviewed in relation to the strong resurgence in exploration for gold since 1979. The resurgence is due mainly to New Zealand's geological endowment with gold and its history as a gold producer. Major past production was from Cenozoic placers of Otago and Westland, late Cenozoic epithermal deposits of the Hauraki Goldfield, and the respective Paleozoic and Mesozoic lode deposits of the Reefton and Otago Goldfields. These same geological environments are the targets of current exploration, mainly in extensions of previously mined deposits. On the Westland and Otago Goldfields alluvial and fluvioglacial gravel placers, mainly representing lateral and depth extensions of previously worked ground, are being mined and prospected. Gold production in 1984 was exclusively from these deposits, and the development of mobile concentration plants has resulted in a great increase in mining activity. Mineralised zones adjacent to previously mined lodes in the Hauraki Goldfield, Reefton Goldfield, and at Macraes Flat (Otago Goldfield) are being intensively explored. At Waihi (Hauraki), an open-pittable resource of about 10 million tonnes of ore has recently been delineated. Some new deposit types and little explored environments are also receiving attention. They include: gold-sulphide quartz veins hosted in an alkaline granite dike in west Nelson; hot spring type gold deposits in fossil geothermal (epithermal) systems of Northland, the Hauraki Goldfield and the Taupo Volcanic Zone; and marine placers off the West Coast where an area of auriferous gravels has been outlined near Hokitika. There is potential in known deposits and prospects currently being evaluated for a large increase in gold production by the early 1990s.

Jan 1, 1986

By E K. Chiw, S-M Jung, S M. Masuka, ika

The world reserves of high-grade iron ore have depleted necessitating the need to utilise any existing natural iron ore deposits to meet the demands of the world’s expanding economy using hydrogen in the reduction process to curb CO2 emission. These low-grade ores include iron ores with high phosphorus content. The thermodynamic conditions in the blast furnace allow for the reduction of phosphorus that readily dissolves into the molten iron. Phosphorus in the gaseous state readily dissolves into the molten iron and therefore must be removed due to its negative influence on the mechanical properties of steel. The removal of phosphorus from molten iron is difficult causing the phosphorus to concentrate in metallic iron. The aim of this study is to provide basic knowledge on the phosphorus distribution after reduction using the CO-H2 and possibly provide the optimum conditions for phosphorus partitioning into slag, increasing the probability of its removal by magnetic separation. Total porosity, pore size distribution and surface area of the pellets used were measured using a mercury pressure porosimeter. The reduction was carried out using thermogravimetric analyses (TGA). The reduction rate increased with increasing H2 and was highest when 100 per cent H2 was used. Metal elements distribution in the reduced pellet was clarified using electron probe microanalysis (EPMA) and showed that phosphorus was distributed in the same areas as Ca. More phosphorus was concentrated in slag when 50 per cent CO–50 per cent H2 was used, increasing the probability of dephosphorization using magnetic separation. The concentration of phosphorus into slag was related to the rate of reduction. Further investigations into the reduction kinetics of this ore by CO-H2 is suggested to validate these findings. Nevertheless, a comprehensive thermodynamic analysis of the reduction of phosphorus containing phases found in iron ore with carbon, CO and H2 was provided to assist in selecting the optimal reduction experimental conditions.

Sep 18, 2023

Industrial and telecommunications organizations around the world are now turning to optical fibres to satisfy their growing needs for data, voice and video communications and to solve transmission problems in noisy and hazardous environments. Already, coaxial cables have been made obsolete for intermediate and long distance applications and fibres are making in-roads on other copper cable and microwave system techniques.The idea of optical fibres is not new, but techniques to manufacture the high quality cable and components required have only recently been developed. Nonetheless, the technology is now advanced, reliable and mature, and costs are plummeting with increased production and market competition.The mining industry has benefited greatly from developments in electronics and communications over the years. Optical fibres are to have a further significant impact and the time is now right for the industry to begin to exploit the many advantages of this new medium. Applications include data transmission, long distance telecommunications, measurement and control systems, surveillance, computer networks, etc.This paper briefly describes the characteristics of optical fibres, current status of the technology, applications and possibilities for future development.

Jan 1, 1984

IN this paper the author's intention is to convey a brief resume of the lead flotation treatment and lead flotation machines, which have replaced the May jigs and Wilfley tables at the plant of the North Broken Hill Ltd., and converted this mill into an all-flotation plant.Attention is directed to the fact that this drastic change from semi-gravity to all-flotation treatment, has been successfully accomplished without resorting to finer grinding than that previously in vogue for Wilfley table concentration, viz.: 10% to 16% plus 40-mesh I.M.M. screen.From the figures now available it is manifest that the scheme of all-flotation concentration-new as regards its successful application to Broken Hill ores is resulting in considerably higher-grade lead concentrates, and is substantially decreasing charges for labour, stores, and maintenance.The new treatment is far-reaching in its simplification of plant, as evidenced by the idle jigs and tables, and the results being obtained by North Broken Hill Ltd. may possibly influence metallurgical practice generally in Broken Hill.The outstanding features of the treatment are:(1) The coarseness, and high grade of lead concentrates obtainable.(2) The low time factor required for flotation.(3) The plant capacity, and the simplicity of its operation.(4) The low horse-power consumption.(5) The small cost for reagents used (not exceeding 3d. per ton of ore).

Jan 1, 1930

This paper describes the technical development of the Newman beneficiation plant over its 23 years of operation and how this development relates to the mine ore reserves of high-grade and low-grade ore. It also discusses the importance of the beneficiation product grades in the overall blending of shippable products from a range of mines to optimise overall ore resource utilisation. Also discussed is the importance of the ore reserve reconciliations in resource utilisation. Data is provided on the capacity and quality improvement results of the plant upgrade, carried out in 1999. This shows how the original capacity upgrade targets have been exceeded and the additional quality benefits that have been obtained from this capacity.

Jan 1, 2002