Search Documents

By Smith Z, Huppert P, Charbucinski J

The paper describes a spectrometric method and apparatus developed for lithology logging in brown coal formations. The nuclear spectromet- ric technique developed is able to delineate coal/sand/clay seams. One requirement was to log inside drilling rods, as well as cased or open holes. The method described is based on combined natural gamma and gamma- gamma techniques using a spectrometric system for signal acquisition and subsequent computer based on-line data analysis and interpretation.

Jan 1, 1989

By Wallman D

Since 1981 two single entry roadways have been driven at Ellalong Colliery for a total distance of 1 030 metres. They were driven at a height of 1.73 metres within the 3.7 metres thick Greta Seam using a Dosco In-Seam Miner (I.S.M.). Ventilation of the drivage was accomplish- ed by an exhausting fan in series with steel ducting and flexible ducting in the immediate face area. The air quantities provided at the face were more than adequate to comply with the requirements of -the auxiliary fan rules and the Coal Mines Regulation Act, 1912, as amended. The experience gained in these drivages demonstrated that the ventilation of long single entry headings can be practically and safely achieved using existing equipment.

Jan 1, 1983

By Horrocks KRS, Smitham JB, Ellison JF

This paper describes the development and installation of equipment for continuously measuring separating density in the dense medium cyclone circuits of the four million tpa Port Kembla B/C plant coal washeries. Monitoring equipment consisting of magnetic coils and differential pressure cells were installed in U-tubes taking the full flow of magnetite from the drain sections of the product drain and rinse screens. The monitoring equipment measures overflow magnetics concentration and overflow density continuously and has operated since 1989. From these measurements and calibration trials, the separating density of operating cyclone modules can be inferred reliably. Variographic analyses of the data show that medium density control to +/- 0.002 RD units and separation density control to +/- 0.007 RD units are achievable. Either method for measuring separation density can be used with approximately the same accuracy, although the overflow density measurement technique suffers from the need to have regular flushing of the Dp cells which complicates the signal analysis. Data from the plant shows that separation density can be controlled by regulating medium density, but the assumption of a constant offset between medium density and separation density is erroneous.

Jan 1, 1993

By Hoppe AJ

Drilling and shooting techniques at Moura open-cut have evolved over a period of 16 years and are the result of hard earned experience combined with established practices and consul- tation with professional services. The wide range of overburden types encoun- ted in the field requires varying methods to achieve the best results at all times. Safe working conditions for the employees and protection of mining equipment is of para- mount importance and close liaison is maintain- ed with the Department of Mines Queensland to keep abreast with changing legislation. Drill patterns, charging profiles, types of explosives and ultimate results are des- cribed in detail along with a resume of equip- ment. Costs of drilling, labour and explosives are also analysed with a total of approximately 20c per cubic metre of shot ground. Future developments and improvements to facilities are also outlined.

Jan 1, 1978

I feel a little like the Parson delivering his Sunday Sermon, chastizing his parishioners for not coming to Church. Those who need to hear me are absent.Nevertheless, I hope that if you agree with what I am about to say you will go forth and spread the word.We often hear of the impact mining has on the community. I prefer tonight to deal with the impact some community attitudes have on mining, and I want to point out that the results of these attitudes rebound to the detriment of our society. I want to deal particularly with regulation, taxation, and proflts.In a civilization whose standard of living is essentially dependent on an adequate and reliable supply of cheap metals and fuels, it should be evident to Blind Freddie that mining must be encouraged.I must express concern at the constraints inflicted on the mining industry by our community. We tend to blame Government for our difficulties, but we must recognize that Government acts merely as agent for the community. It is fair to say that in a free society, if Government actions do not reflect the demands of the electorate, then it doesn't stay the Government. It is important though for Government, in framing its policies, to ensure that it is not unduly influenced by the loud voices of minority groups.The people of our nation have every right to demand that our industry meet certain criteria to be allowed to operate. We all wish to live in a healthy and congenial environment, and to have our individual comforts protected. It is essential, however, that the community realizes that its demands on the mining industry are affecting Australia's prosperity.Each new regulation and each new tax or impost has its effect on investment, employment, and national revenue. Restraints result in an increase in costs which in turn raises the minimum value of a mineral deposit which is economically mineable. It results in minerals, which could be mined under more favourable circumstances, remaining in the ground, perhaps lost for ever.

Jan 1, 1978

At the beginning of the seventies pre- drainage of methane was introduced in West German coal mining in order to reduce the gas emission from the worked seam. After three pilot tests on the "Rheinland" Colliery (86 boreholes in seam "Prasident"), "Bergmannsgluck/ Westerholt" Colliery (23 boreholes in seam "Gustav") and "General Blumenthal" Colliery (27 boreholes in seam "Hugo" and 170 boreholes in seam "Karl") systematic large scale tests with extended investigations were carried out un the "Rheinland" Colliery (127 boreholes in the seams "Anna", "Blucher", Prasident"). During this time an analogous test was carried out on the "Consolidation" Colliery (21 bore- holes in seam "B"). In these studies and tests the technical feasibility, efficiency and economy could be proved, so that pre-drainage of methane starts spreading. On the "Rheinland" Colliery pre-drainage has become common practice in gassy seams. Mainly two points impede a faster spreading of method: 1. in many cases the necessary requirement, that one or both of the gate roads should ire driven 6 to 12 months before the face is worked, is missing. This is mainly due to the difficulty of retreat mining in passe seams.

Jan 1, 1982

Jan 1, 2004

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988

By Zeni J. T

Gold was mined from quartz bodies at Ballarat East from the 1850s until closure of the last mine in 1917. The average depth of mines was about 350 m.Ballarat Goldfields Limited (BGL) carried out diamond drilling from surface between 1985 and 1987 which proved the continuation of gold-quartz mineralisation beneath the old mines.During 1989 an underground development program was commenced to access the mineralisation for detailed exploration. The program included two simultaneous shaft developments. These were known as B2 shaft and Llanberris No.1 shaft.

Jan 1, 1992

Whereas traditionally, stable isotope research has been directed towards resource exploration and development, it is finding more frequentapplications in helping to assess the impacts of resource utilization upon ecosystems. Among the many pursuits, two themes are evident:(1) tracing the transport and conversions of pollutants in the environment and(2) better understanding of the interplay among environmental receptors, e.g. food web studies. Stable isotope data are used primarily to identify the presence of pollutants in the environment and with a few exceptions, the consequence of their presence must be assessed by other techniques. Increasing attention has been given to the isotopic composition of humans with many potential applications in areas such as paleodiets, medicine, and criminology. In this brief overview examples are used from the Pacific Rim to illustrate the above concepts. Stable isotope data will undoubtedly play an increasing role in multi-disciplinary research in the Pacific Rim. However, consideration should be given to more effective strategies, e.g. networking, for pursuing large scale problems such as long range circulation of pollutants.

Jan 1, 1990

By Jones KW, McClelland RA, Denholm WT, Taylor RN, OÆShea J

Associated Tin Smelters, Sydney, are developing tin smelting operations in a prototype commercial SIROSMELT plant comprising two furnaces of 5 to 8 tonnes capacity. Features of the plant and its operation are discussed and results of its application to tin slag reduction and high-grade tin concentrate smelting are presented. Development work is still in progress but experience indicates that the technology has potential for lowering the costs of tin smelting and relieving constraints on grade and iron content of concentrate imposed by conventional technology.

Jan 1, 1984

By Spencer P. A

Bacterial oxidation, previously known as bacterial leaching or bio-leaching, has been applied at laboratory and pilot plant scale to many refractory ores and concentrates around the world. The most common bacterial culture used in this process has been Thiobacillus sp. This organism is limited in commercial application, especially in Australia for several reasons. The optimum operating temperature range for this culture is 30¦C to 40¦C and high levels of some metals such as arsenic, silver, and copper have toxic effects on the culture thus reducing its effectiveness. The culture employed by BacTech (Australia) Pty lid is a moderately thermophilic culture which operates in a temperature range of 40¦C to 55¦C (which is more amenable to the Australian climate) and with higher resistance levels to metals often found to be toxic to Thiobacillus sp..

Jan 1, 1991

By Distin P. A

The extraction of platinum and rhodium from scrapped honeycomb autocatalyst into hydrochloric acid/aluminum chloride/nitric acid solutions is described. Results are given for the effects of leachant composition, temperature and catalyst pre-reduction using hydrogen. Data are also presented for the recovery, by hydrogen reduction, of platinum and rhodium dissolved in the leach solution. Parameters studied include solution composition and temperature, hydrogen pressure, and platinum seed addition.

Jan 1, 1992

By Bhattacherjee A, Makesh S

Mechanised sub-level stoping is one of the most widely accepted stoping practices followed in base metal mines in India. As a general practice, blast-scheduling of rings in these stopes is done either heuristically or randomly which leads to a high fluctuation in ore grade when drawn and delivered to the mill. In this paper, dynamic programming has been investigated as an optimisation technique for optimal blast-scheduling of rings. A microcomputer based dynamic programming algorithm has been developed in C language which runs under the UNIX environment. A case study based on Indian mine data is presented to demonstrate the application of the dynamic programming concept and use of the developed software. It is concluded that dynamic programming can be used as a production planning tool in Indian mines practicing sub-level stoping and following heuristic/random approaches for blast-scheduling of rings.

Jan 1, 1995

IT is very difficult for a founder engaged in jobbing work, comprising all sizes and classes of castings, to appreciate that the analysis of the iron he is using cannot entirely fill the situation he desires for his varied classes of work. Neither is there any panacea in the shape of an iron mixture that will suit the whole of his floor for the day.From his own experience he generally alters his cupola charges during the cast, endeavouring to meet at the same time the requisite metal composition for the castings he is about to pour.The founder on repetition work is in a much better position to stabilise his methods, arrive at a certain pig-iron' analysis, regulate...

Jan 1, 1926

By M Chaudhari, G Manekar, D Shome

MOIL Limited is operating 7 underground and 3 opencast mines in central India and producing annually more than 1.2 million tonnes of various grades of manganese ore. The underground mines are operating at shallow - 90 m at Munsar mine to moderate - 353 m at Balaghat mine below the surface with horizontal cut and fill (HCF) or its variant method of stoping with post filling by hydraulic sand stowing. The Munsar mine is being worked underground since 1903. The opencast mining is presently stopped. The ore body below the opencast quarry is geological continuity of the area excavated in past by opencast method of mining. The underground mining is done through the adit in three levels i.e. 270’L, 220’L, 170’L and by incline in western part of the property at 70’L. The horizontal drift development has been developed in the manganese ore body with sill drive of 5 m above the sill pillar in lower level at 70’L and barrier pillar of 5 m thickness is left for protection of upper level at 170’L. Valuable mineral has been locked in sill pillar and therefore rock mechanics investigations have been carried out. On the basis of study now the drift development has been carried out in footwall rock at 70’L, (-) 30’L and below levels and it has improved the mineable manganese ore by about 20%. In this modified HCF stope design, an alternative fill material in place of sand, which has been developed in house by use of overburden (OB) material after treatment, has been used for hydraulic stowing. The experimental trials find out that the alternative fill material of OB is more compact and forming a non expansion floor for the men and machines in the stope. This will certainly help in the introduction of mobile underground mining equipment for drilling in the stopes and mechanical mucking, transportation and loading of the ROM. The paper presents rock mechanics investigations and future use of alternative fill material of OB for better safety and productivity at Munsar Mine of MOIL. CITATION:Manekar, G, Shome, D and Chaudhari, M, 2018. Modified ground support with alternative fill material for ground control at Munsar underground manganese mine of MOIL Limited, India, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 58–65 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A Tomsett, J Rutter

Ore control systems at Ridgeway have been designed to deliver gold and copper metal production through focussing on the ore characteristics that impact on mine and mill performance and ultimately metal delivery. This is achieved using data collection and management systems which allow data to be collected digitally with æat captureÆ validation routines. This data forms the basis of forecasting systems which aim to accurately assess local in situ and drawn ore characteristics. Physical attributes of ore such as draw characteristics, brow conditions and visual grade estimation are rountinely recorded. Ore tracking and accounting systems monitor gold and copper grade, copper mineralogy, host lithology and ore sizing. These have material impacts on concentrator throughput and metal recovery. Routine reconcilation and check sampling allow calibration of these systems.

Jan 1, 2002

This paper discusses the use of tapered roller bearings in conveyor idlers. It shows that in medium and high capacity systems, tapered roller bearings can offer significant cost and performance advantages. In the next ten years, conventional conveyors will face increased competition from unconventional belt conveyors, pneumatic systems, pipeline "slurry" systems, unit trains and so on. The conveyor industry must meet these challenges by innova- tive use of technology. Conventional belt conveyors must continue to show the lowest cost per tonne-km or lose their position in the market. Tapered roller bearings can contribute to the achievement of this goal. The concurrent resources boom and liquid fuel crises may well see a decline in the use of heavy trucks for bulk material handling over moderate distances 10 to 50 km. There appears to be a trend in the conveyor industry to go to higher speeds with improved belting in conven- tional widths. The transmission of more material over a given period of time will place more demands on conveyor idler bearings. Australia has in general followed the European practice of using deep groove ball bearings in conveyor idlers.

Jan 1, 1978

By Jones IO

Although small units have been in use formany years, particularly in opal mining at shallow depths, there has been little effort in the past to explore the potential of the vacuum lift system in other more demanding applications. Recent developments in Western Australia by a small number of mining companies, contractors and manufacturers have seen the design and construction of several larger, more powerful units for use in winzing, shaft sinking, hoisting and spillage removal. Some of these units have proved very successful and suggest that they could be developed for a wider range of applications and duties in future.

Jan 1, 1984

By Hyslop W

It is shown that coke has a major influence on the pattern of operation and on the aerodynamics of the blast furnace and that the physical and chemical characteristics of coke, at each stage in the furnace, determine its ability to satisfy requirements for iron production and coke economy. Analysis of coke sampled from operating furnaces is compared with furnace behaviour. The available data suggests the importance of segregation, strength, size change and chemical degradation of coke on furnace performance. Correlations are presented for coke breakdown ratio as a function of coke rate and hearth diameter which shows that breakdown increases with hearth diameter and with decreasing coke rate. It is also shown that the Micum tests do not reflect the coke strength in a predictable way and that solution reactions appear to play an important role in giving rise to a pitting effect on the cell walls of the coke with the resultant deterioration in coke properties. The catalytic effect of activating substances, such as alkalis, is noted and results are presented which show the effect of carbon solution on the coke strength. The importance of coke in the stack and in the bosh is discussed and flooding results are presented for BSC furnaces which show the probable driving limits for the furnaces considered. It is also shown that coke sampled from different tuyeres in a furnace gives quite different flooding limits. Other applications of the coke test work at BSC are also noted and the relevant objectives listed.

Jan 1, 1975