Search Documents

By Storey AG

Following initial plant scale work on the development and performance of 'spray' oil lances, a full scale room temperature model of the blowpipe-tuyere region of a blast furnace was built to study the basic aerodynamic features of auxiliary fuel injection procedures. Mobilwax 2305 was used as a substitute for Bunker C oil fuel in view of its similar physical properties and the fact that the atomised droplets could be frozen in flight and size, distribution analyses made for various operating procedures. It was shown that secondary atomisation processes far outweighed the importance of any primary atomisation procedures in determining mean Sauter Diameters particularly at high windrates typical of current blast furnace technology. It was also found that good spray dispersions across the blow pipe could only be obtaind for liquid fuels and that the lateral rate of spray dispersion was substantially enhanced by primary atomisation procedures. Mean particle diameters of sprays were found to be predictable on the basis of elementary stability theory and fell within the size range necessary for good combustion at all liquid fuel rates studied. The possible effects of high oil injection rates on flooding phenomena in the furnace bosh were considered. Comparisons show that high oil rates can lead to significant increases in the hanging factor (e.g. 'V 10% at 135 kg oil/thm) owing to increased gas flow rates/thm resulting from the presence of hydrogen.

Jan 1, 1975

It is now 32 years since Walsh's classic publication (1) heralded the beginning of atomic absorption spectrophotometry (AA) as we know it today. During this time, AA has developed into the most widely used analytical techniques for the determination of the metallic elements. The years have seen progressive changes in instrumentation so that today it is a highly sophisticated technique. One area of development in AA that is experiencing renewed attention is in the area of electrothermal excitation. In this technique a flame is not used by the analyte solution is atomised by an electrically heated graphite furnace. For a large number of elements the graphite furnace atomic absorption spectrophotometer (GFAA) is considerably more sensitive than flame work. It is common to be able to detect concentrations one hundred times smaller than those possible by flame. Today's geochemists are finding that they can gain valuable information out of very low limits of detection. Electrothermal atomic absorption spectrophotometry (or GFAA) allows for low limits of detection and can be seen to be a valuable aid to geochemical prospecting Analysis.

Jan 1, 1987

By Ranklin W. J, Swinbourne D. R

Lead blast furnace slags contain typically 10 - 20 mass per cent Zn. The zinc can be recovered by slag fuming, in which a powdered coal/air mixture is injected into a molten slag bath. Volatilised zinc is recovered as zinc oxide from the gas and processed hydrometallurgically to produce zinc metal. The ISASMELT continuous lead smelting process in operation at Mt Isa produces a slag containing about 12 per cent Zn which is currently granulated and stockpiled. This slag could flow to a further bath-smelting reactor for continuous zinc fuming. Rather than collecting the zinc as fume from such a process, one option would be to recover it using a lead splash condenser. The success of this operation would depend on the composition of the gas produced, in particular the concentrations of gases capable of reoxidising zinc vapour, viz, carbon dioxide and water vapour. The aim of this investigation was to determine the smelting conditions for a bath-smelting process such as ISASMELT or SIROSMELT which would produce a gas similar in composition to that from an Imperial Smelting Furnace by thermodynamic modelling of the process using the CSIRO Thermochemistry System. It was found that such a gas could be produced if coal injection and oxygen enrichment of the combustion air to at least 40 per cent 02 were used. However, the off-take gases must be conditioned by addition of methane to reduce the water vapour content to acceptable levels. An addition rate of ten per cent of the off-gas flowrate was found to be adequate. Addition of methane to the off-gas had the added advantage of cooling the gas from the bath temperature to a temperature suitable for normal lead splash condenser operation.

Jan 1, 1993

By Virtanen M

Grinding has been one of the areas of major development at Outokumpu's concentrators. During its early years the company used entirely rod and hall mills, but due to the high costs of metallic grinding it began the testing of autogenous grinding as early as the 1950s. In the late-1970s, the company's own modification for two stage autogenous grinding was ready for industrial use. Surprisingly late, in the 80s - 90s, an interest rose to check also the effects of grinding methods on flotation results. This paper firstly gives a short history of the development work of Outokumpu type autogenous grinding, called 'Outogenius'. The effects of some grinding methods on the process results of two nickel ores are then reviewed. The tests to date show notable effects of grinding methods on flotation.

Jan 1, 1996

By C Mroczek, B Mitchell

Perilya Broken Hill, from its inception, has budgeted for more than 2.0 million tonnes per year from the Southern Operations. This tonnage was planned to come from in excess of 100 stopes per year in a remnant mining environment with numerous mined voids and consequent mining challenges. To mine an average of two stopes per week requires patience, flexibility and detailed knowledge to best manage the potential risks and hazards. The evolution of the Perilya Broken Hill Mine Planning Process has necessitated the establishment of a process to identify and manage these risks during the planning stage in a reliable but efficient manner. This process is to ensure that vital steps for each stope are not missed, and that each personÆs work can be tracked by other members of the team. This paper outlines the planning process from resource to stope closure.

Jan 1, 2005

THE auriferous sulphide ores of the eastern end of Gippsland, and notably of the Cassilis and lVIitta districts, are amongst the most complex and refractory in Victoria-perhaps in Australia. The minerals occurring in these ores are pyrite, arseno-pyrite, zincblende, galena, and (in smaller amounts) some of the copper, sulphides, as chalcopyrite and covellite; and some of the antimonial minerals, notably stibnite and jamiesonite. In the oxidized portions of the lodes, the oxidized lead and iron minerals, and small amounts of the hydrated arseriiate of iron, are found.In the Cassilis mine, near Omeo, copper is present usually in quantities of under 1 %. The magnetic sulphide of iron is of fairly common occurrence. In, the upper levels of the Cassilis mine tin was usually present, the amount going up to 3% in some samples of concentrates. These minerals occur sometimes banded, but usually as an intimate mixture-pyrite and arseno-pyrite predominating. The gangue is usually quartz (blackened by enclosed particles of sulphides). Calcite, magnesium silicate and felspar are also present in varying amounts.

Jan 1, 1911

By A J. Moore

Predictive assessment of surface blast vibration requires the identification and quantification of significant factors, and the summation of their combined effect. Methods available for the prediction of significant factors are described, and examples are given of the combined use of these methods to evaluate alternative proposals.

Jan 1, 1999

Techniques and results achieved during the excavation of the Melbourne Underground Rail Loop (HURL) are summarised and discussed in the context of the various restraints present in a typical urban construction project. Mechanical methods (as distinct from those utilising blasting)accounted for the bulk of the excavation. Ground support was critical in this particular geological excavation setting, but is not discussed in detail except insofar as it constitutes a restraint to excavation progress.

Jan 1, 1978

By Holliday RJ

The Imperial Smelting Furnace (ISF) was developed in Britain during the 1950's as a process which could produce zinc from a blast furnace. Since then it has evolved into an efficient means of producing zinc and lead from lower grade raw materials, both of primary and secondary origin. These changes have been in response to the need to improve the cost competitive position of the ISF in a climate of decreasing metal prices. The improvements at the Cockle Creek smelter of Sulphide Corporation Pty Limited have resulted from work undertaken in four main areas: 1. Changes in plant design and operating practice to give more stable furnace operation. 2. Improvements to the quality of sinter being charged to the furnace. 3. Improved monitoring of process variables and the formulation of control strategies based on the improved data. 4. Increased understanding of the processes occuring within the furnace shaft to allow predictive modelling to be undertaken. Work in these areas is still progressing but the work to date has resulted in a significant improvement in the production rate and efficiency of operation.

Jan 1, 1984

In 1955 the annual production of steel at Australian Iron and Steel Pty. Ltd., Port Kembla was 1.2 million tonne and over the following two decades this had progressively increased to the present capacity of 5.4 million tonne per annum. This increase in productivity has also been accompanied by important developments in steelmaking technology and these are explained in the chronological order in which they have taken place. Reference is made to the use of oxygen in open hearth furnaces, the B.O.S. process, the Argon-Oxygen decarburisation process for stainless steel, vacuum degassing and continuous casting. When the vacuum degassing and continuous casting units are commissioned, the Port Kembla Works will have achieved a standard of steelmaking technology equal to any in the world.

Jan 1, 1976

Sasol Roche Blasting Services (SRBS) has undertaken a process of trialing and evaluating the use of the SMI electronic initiating system with the specific purpose of being able to fully quantify the benefits of the system over a pyrotechnic system. After an initial trial of three shots in mid-2001, it was decided that to fully quantify the system, a complete strip would need to be fired using the system so that any losses due to ramps or end walls would be the same for both scenarios. The results have shown a significant improvement over the use of pyrotechnic initiators in several key areas including percentage cast. Through the use of survey results, the increase in cast and subsequent net improvement in blasting has been quantified. These trials have set out to compare each system in comparable situations to determine the real benefits, if any, of the electronic system over the pyrotechnic one. As the percentage cast is relatively easy to quantify using modern survey techniques, it was decided that this would be the principle method of comparison. However, while the assessment only included survey results, any improvement in fragmentation size and consistency would have flow on effects on reduced running and maintenance costs.

Jan 1, 2003

By Tronson K

Improvements in technology do not necessarily lead to higher profits: the benefit of lower costs can be captured by coal buyers, governments and workforce rather than by the colliery operators. The economic impact of longwall mining in Australia has been critically assessed to provide lessons for the future. For a variety of reasons, companies investing in longwall equipment in the past five years have generally not achieved an adequate return on the funds invested. The effect of technological innovation must be examined in the light of competitive forces operating in the market. Projections of cost reduction trends in the coal industry have been applied to a world cost model to provide a picture of the coal industry in the year 2000.

Jan 1, 1988

By M Hudyma

Open stope mining is the most common mining method employed in underground, hard rock mines in Canada. It is characterised by relatively small, single lift stopes (20 000 to 100 000 tonnes), and fast stope turnaround times. Host wall rock mass conditions, which are typically poor to fair, are the controlling parameter in stope dimensioning. Rock mass stability is maintained by designing all stope surfaces at a stable dimension, and through extensive use of cablebolting for stope backs and frequently stope hanging walls. Dilution control is a high priority. The typically small, high-grade, deep and irregularly shaped orebodies are incrementally developed, usually in a bottom to top direction. In many cases, high stress is encountered due to the depth of the orebodies. Overstressing of pillars and hanging pillars are avoided through the use of pillarless or early pillar recovery mine sequencing strategies. Stopes are invariably filled, and in higher grade and wider orebodies, cemented fill is commonly used. This paper generalises many of the similarities found in Canadian open stope mines.

Jan 1, 2000

By R Vleggaar

In addressing a short-term operational need for the relocation of a tailings storage facility reclaim pond, a mine has achieved a host of water management objectives. Through effective planning and adoption of a strategic æwhole of mine lifeÆ approach, the mine has achieved significant environmental, social and economic benefits. A review of all water management aspects across the site identified a host of other interrelated water issues and concerns which, if dealt with individually, would prove too costly for individual operational departments. When considered as a whole, however, the issues became opportunities and provided the stimulus for integration of the site water management system. The development of site water and solute balance models provided the tool by which a number of water management options/strategies could be evaluated. The conceptual design and costing of the proposed water infrastructure further facilitated the evaluation of the multiple benefits to be gained from each option. A business case could then be made to mine management for the preferred option. The recommended water management strategy finally recommended to the mine not only provided a tailings storage facility (TSF) reclaim pond, but also provided for:increased wastewater recovery from the TSF, the capture of all waste rock dump run-off, additional water harvesting from local creeks, increased wastewater reuse, improved environmental water management, infrastructure that could be used by the local community after mine closure, and overall cost savings. This paper illustrates how effective water management planning can provide both short-term economic and environmental benefits, as well as long-term social benefits.

Jan 1, 2006

A brief descri;tioki is given of nuclear power reactors and their fuels. These fuels are made from a variety of uranium compounds such as uranium dioxide, and uranium carbide as well as uranium metal and its alloys. The various processes used to produce some of these compounds from yellow cake are outlined. Using the natural uranium, heavy water reactor by way of illustration, fabrication of fuel elements is dis- cussed and the characteristics of U02 powder required for this partic- ular fabrication are indicated. The flowsheets and equipment presently in use overseas for production of this type of U02 powder are described. Possible areas where improvements might be made to this conventional process are enumerated and some details are then given of the programme of work which has commenced at the A.A.E.C. Research Establishment to gain experience in the general field of nuclear grade UO20

Jan 1, 1968

A paper describing the treatment of the Mary Kathleen uranium ores must necessarily be historical and confined mainly to a review of the four papers which have already appeared. Couche and Hartley (1958) described the development of the treatment process just prior to the commencement of operations in June, 1958. Harris, Boag and Hemingway (1961) described the treatment during the operations, and Wreford (1965) reviewed all aspects of the mine and mill, when operations were suspended in November, 1963. Harris and Steele ('1960 presented a paper especially describing the radiometric sorting operation. Some hitherto unpublished information is also presented in the paper to describe some of the peculiarities of the ore, indicate reasons for the adoption of the treatment flowsheet, and some interesting problems connected with this treatment.

Jan 1, 1968

FaulIing west of the Mount Isa mine is described and is shown to be related to three groups of folds that have been recognized in the area. The first period of faulting postdates the first generation folding; these faulIs are regional faults (tectonic discontinuities) which are folded by second generation folds. The faulting accompanying the second generation folding divides the area west of the Mount Isa mine into four structurally and metamorphically identifiable blocks. The most prominent of these second generation faults is the Mount Isa Fault, which is characterized by a number of distinct zones of intense second generation folding and the presence of localized layers of mylonite. Only limited evidence for brittle deformation has been observed and the major movement appears to be associated with the plastic deformation of the rocks. Confined to the areas of second generation folding in the Mount Isa Fault are numerous third generation kink folds. A detailed description of the Mount Isa and other faulIs is presented together with evidence for their existence. The displacement accompanying this faulting cannot be established because of the complexity of the structure.Postdating these faults and all the folding of the area are minor cross faults.

Jan 1, 1973

This paper outlines some of the recent developments in Spiral Concentrator design, with particular reference to the range of Reichert spirals supplied by Mineral Deposits Limited, typical applications, and test or operating data, are also provided for the different series of spirals now available.

Jan 1, 1978

By Scherbatsky VB, zon BM, Babushkin NM, Kitaev BI, Shabel&apos

The structure and hydrodynamics of the raceway zone of a blast furnace was studied on a cold model representing a sector containing two tuyeres. The model differed from the usual in that it was prov- ided with continuous flow of the coke layer at pre- determined rates, had provision for changing the tuyere parameters (diameter, protrusion, inclinat- ion) and irrigation of the layer with liquid. A combination probe was developed which per- mitted simultaneous measurement of the pressure field both across the area and through the height of the layer as well as determining the topography of the raceway. The velocity fields in the layer were measured with a specially made impulse thermo- anemometer. The determining criteria of the model were taken as the relationships between the energy of the blast and the particles, the dimensions of the raceway and the cross-section of the tuyere. The model established the effects of the tuy- ere structural parameters, blast parameters and amount of liquid products of smelting on the con- figuration of the raceway, the structure of the layer, pressure and velocity fields in the vicinity of the tuyeres and in the vertical direction through the layer. The properties of the raceway formation and the structure of the layer in motion have been clarified.

Jan 1, 1981

According to our experimental results, the following oxygen probe recommended, that is, the magnesia stabilized zirconia was employed as a solid electrolyte and Fe.FexO solid elect- rode was used as a reference electrode. Using such an oxygen probe, we tried to measure the oxygen potentials in molten metals, mattes and gases in the following fields of non-ferrous metal industry, molten copper in the side launder before casting, molten crude lead in the forehearth of ISP blast furnace, molten copper mattes in the forehearth of blast furnace and in the settler of flash smelting furnace, gas in the settler of copper flash smelting furnace and flue gas in the electric furnace for ferro-silicon. In the past ten years or so, many experi- mental results in the field of fundamental studies have confirmed that the equilibrium oxygen potential could be measured conveniently and accurately by an electrochemical method using a zirconia solid electrolyte. Recently, such an electrochemical technique has been also applied to a device for physicochemical invest- igation or process control in the non-ferrous metal industry. Such a device consists of an oxygen con- centration cell with stabilized zirconia, and it is commonly called an "oxygen probe" or "oxygen sensor".

Jan 1, 1980