Search Documents

By Jack J. Ayotte, Michael R. Nadon

"Today's demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco's Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine's 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco's Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

By K. Awuah-Offei

Long-term production scheduling optimization has been a challenging issue for the mining industry because of the size and complexity of the problem. The current planning algorithms have limitations in terms of addressing the stochastic variables underlying the mine planning problem. In this paper, an intelligent agent-based mine planning framework based on reinforcement learning is introduced. The long-term mine planning is modelled as a dynamic decision network. The intelligent agent interacts with the block model by means of a stochastic simulation and employs a Q-learning algorithm to learn the sequence of pushbacks that maximizes the net present value of the mining operation. The intelligent open pit simulator (IOPS) was implemented with an object-oriented design in Java®. A comparative application case study was carried out to verify and validate the models. The proposed method was used in planning an iron ore deposit and the results were compared to the Milawa scheduler used in Whittle® software. The outcome of the study demonstrates that the intelligent agent framework provides a powerful basis for addressing real-size open pit mine planning problems.

Jan 1, 2008

By G. D. West, J. D. Purdue

"Marked Ball Wear Testing (MBWT) employs identified grinding balls which are placed in an operating mill for a period of time, retrieved from the mill, and then measured to determine the amount of wear experienced. This is an excellent method to evaluate the relative differences in the wear rates of various grinding ball materials and/ or manufacturing process variables simultaneously and under actual production milling conditions. This paper outlines the methods of ball identification, testing and evaluation procedures and discusses the strengths, weaknesses, and proper application of marked Ball Wear Test results. INTRODUCTIONThe consumption of grinding media in the mineral processing industry represents a substantial cost to the comminution process. Grinding media is most often found to be the second highest consumable cost next to energy. To determine the selection of the most cost effective media, one must determine the specific wear mechanisms present in a given grinding application and decide which media system addresses these mechanisms most economically.A MBWT has definite advantages over other methods used to evaluate the relative consumption rates of grinding media. It allows the comparative testing of a large number of different ball types under identical operating conditions in a very short period of time. In addition, production wear rates can be accurately predicted directly from MBWT results. Typical MBWT test periods are in the order of 350 to 700 operating hours for high wear rate application and upwards of 2000 or 3000 hours for low wear rate applications. These times are much less than the 5000 or more hours required to purge a mill of the incumbent ball charge (to convert it to the test ball) and then provide even a minimal test period in which to conduct a full production test, for just one type of ball. Under production test conditions the evaluation of competitive product or the development of improved grinding balls is necessarily slow."

Jan 1, 1991

The common theme of these four objectives is declaration. Declaration tells the compiler that an entity exists and also provides the name and nature of the entity. Since everything you create has to be declared, you must know how to declare correctly and be able to make appropriate use of all the declaration tools available to you. This objective recognizes the importance of declaration by requiring you to know everything about Java declarations Write code that declares, constructs, and initializes arrays of any base type using any of the permitted forms both for declaration and for initialization. This objective addresses your understanding of all aspects of arrays. Arrays are the simplest possible data collection and are supported by all modern programming languages. However, Java?s arrays are different from those in other languages, especially C and C++, because they are actually exotic objects. This objective recognizes the importance of being able to make use of all the functionality of arrays. You will be expected to know how to declare, construct, and initialize arrays.

May 1, 2011

By Justin S. Johnsen

As OEM sensors and interfaces have grown in number, the available data from equipment in the mining environment has continued to multiply. This equates to an increased visibility of operating performance, mechanical and electrical health, and predictive monitoring that can directly improve maintenance reliability and scheduling. With increased visibility, where should a reliability engineer begin to look to directly impact Capacity Assurance? More specifically, what source will provide inputs to the Failure Modes Effects Analysis (FMEA)? Results from these analyses must be documented, and they must contribute to the overall mission of the mining company; these results must reduce costs and increase profits. Through detailed data capturing, documenting, and analysis, Modular Mining Systems? Time Tracking application, used in the MineCare® maintenance management solution, can drive decisions and provide direct impact to engineering projects for continuous improvement in the mine maintenance organization.

Nov 1, 2011

By S. Hill

For a mining operation, the determination of the best place to build haul roads is typically done by hand, or with the assistance of rudimentary shortest path optimisation algorithms. Straight line, point to point, modelling of costs is often used with distances multiplied by constants that are based on rise of the road between the points. Failings of this approach are that straight line approximations are notoriously poor as they do not take into account areas where a truck cannot travel. In addition, the rise and fall of the road may vary considerably over the truck journey meaning acceleration/deceleration and varying truck speeds are not taken into account. Lastly, the use of rudimentary optimisation algorithms means properties a truck must obey such as minimum turning circles, line of sight restrictions or even that the truck must travel forward at all times are not taken into account. Thus solutions generated may not be feasible, let alone optimal. In this paper we discuss a state of the art parallel Artificial Intelligence tree search technique for solving haul road location problems. As well as the above properties, factors such as road utilisation, cut and fill, and construction costs are taken into account. The combination of advanced modelling and fast computing and optimisation techniques produces significant benefits both in terms of time to generate roads and cost savings. Preliminary results where this method has been used are discussed.

Aug 1, 2013

By W. A. Jones

Purpose of Paper Geophysics is a highly developed science which has found a wide use in industry. Perhaps the most spectacular application has been in the field of oil exploration. It has been estimated that, up to the end of 1939, geophysics was responsible for the discovery of five billion barrels of oil. In 1944, the sum o $40,000,000 was expended for geophysical work in the search for new oil deposits. Although the metal mining industry has so far made comparatively little use of the science, it is becoming increasingly common for the exploration engineer or geologist to be required to co-operate with the geophysicist. Many papers dealing with applied geophysics have been published but in most of them advanced training in physics and mathematics on the part of the reader has been assumed. It is difficult for the average engineer to obtain a ready understanding of the equipment, field procedure, and scope and limitations of the science from the literature. The present paper attempts to describe briefly and in simple terms the principles underlying magnetic, self-potential, and electrical resistivity methods and their application to a field problem. Introduction Geophysics is concerned with the study of gravity, magnetism, natural earth currents, earthquakes, vulcanism, and many other natural phenomena. The methods, originally devised for the measurement, for scientific purposes, of the forces associated with such phenomena have been adapted to the search for buried deposits of economic value. If the body sought has large dimensions and distinctive physical properties, geophysical measurements may reveal associated, and in some cases quite characteristic, anomalous features. However, in many instances the mass cannot be indicated directly but has a common association with geological features which can be defined by physical measurements. Although such surveys cannot specifically identify oil, metalliferous minerals, or other commercially valuable substances, it is possible to delineate anomalous sub-surface physical features which, with the help of geological information, can be assessed as possible or probable indications of the body or structure sought. The nature and extent of the material causing an anomaly, and its economic importance, can only be determined by further exploration, such as drilling.

Jan 1, 1947

By F. Halverson

"The theory of flocculation usually is in a state of flux, involves many diverse phenomena, and is complex and sometimes contradictory in details. Instead of attempting a general discourse, I shall discuss selected observations made at our Stamford Laboratories, which impinge on theoretical aspects in two somewhat distinct areas of flocculation. Since some of you many not be familiar with flocculation, and :.n order that we all attach the same meaning to the jargon used, I first would like to review briefly a generalized picture of what goes on.Assume we have a suspension of particles in water, with a distribution in the sizes of particles. The surfaces of the particles interact to some extent with the water--· tending to alter the extent of hydration, may generate some ion exchange, all being somewhat variable with time--developing a surface condition which is very complex in details. We refer to this suspension as the ""substrate.""In the usual situation, if the suspension is allowed to stand quietly, the large particles settle out first, with somewhat smaller particles settling more slowly, and then there is a portion of very fine material which takes a long time or doesn't settle out at all. This resistance to settling t~ the very fine particles results from many factors, but all relate back to the size and density of the particles, to their surface properties, and to the other components in the aqueous suspending medium."

Jan 1, 1978

By R. E. Michelutti

"The Sudbury area environment became drastically altered commencing in 1871 with lumbering, repeated fires and early open roasting operations from 1887 to 1929. These combined factors had such a pronounced effect that approximately 24 square miles were totally denuded of any vegetation and 87 square miles were semi-barren to somewhat stressed.The two nickel producing companies in the area have reduced the sulphur dioxide emissions considerably over the years. Falconbridge Limited, alone, reduced sulphur dioxide emissions by 77% from 1971 to 1984.These reductions have resulted in improvements to the air, soil, lake and vegetation quality in the Sudbury area.INTRODUCTIONThe Sudbury area environment became drastically altered commencing in the 1870's with lumbering, repeated fires and early open roasting operations from 1888 to 1929. These combined factors had such a pronounced effect on the Sudbury environment that approximately 24 square miles (64 sq. km.) were totally denuded of any vegetation and 87 square miles (225 sq. km.) were semi-barren.Over the years, the Sudbury area environment has improved considerably. This has been due to emission cutbacks by both Inco Metals and Falconbridge Limited, coupled with industry, government and community reclamation programs. Before the improvements are discussed, a better understanding of the historical degradation is required."

Jan 1, 1986

By Tao Long

Recently, the great amount of funds has been invested in the reconstruction of damaged infrastructure and house of subsidence area of coal mine and mine reclamation. This is a benevolent and popular work, which is highly praised. However, because of complicated collapse area problems in China, especially the less integrated control research in the collapse area of metal mine, and the technological weakness, how to effectively control the subsidence area, restore landscape and ecological environment, and utilize the abandoned mine land, are major issue related to the mining area of sustainable development. The research situation about the formation of metal mine collapse area at home and abroad is reviewed, and then the effect of the collapse area on the mine safety and ecological environment, the existing technical problems and development direction are analyzed. Lastly, the technical measures of the collapse area control and cooperative underground mining is put forward.

Oct 1, 2010

By Troy Boisjoli, Sean Hillacre, Matt Batty

Discovered in 2014, the Arrow Uranium Deposit has undergone rapid development through successive drilling programs informed by geostatistical drill hole spacing studies. An independent third-party geostatistical drill hole spacing study was completed by Clayton V. Deutsch Consultants Inc. in 2017, evaluating the uncertainty of thickness, grade, density, and areal limit of the Arrow Deposit to determine a drill hole spacing suitable for Indicated Mineral Resources. Indicated spacing was defined to be 24 to 32 metres (“m”) to be within 15% of predicted for a nominal quarterly production volume with a probabilistic tolerance between 75 and 90%. The study not only defined the Indicated Mineral Resource resultant from the 2016 drill program, but also provided drill hole targeting criteria for subsequent drill programs aiming to convert Inferred to Indicated Mineral Resources. A subsequent geostatistical drill hole spacing study on the Arrow Deposit was completed by Clayton V. Deutsch with Resource Modeling Solutions in December 2018 to define Measured Mineral Resource spacing in support of the 2019 drill campaign. The study resulted in a drill hole spacing of 9 to 17 m to be within 15% of predicted for monthly and quarterly production volumes using an accepted industry probabilistic tolerance of 90%.

Jan 1, 2020

By R. Hamilton

"Louvicourt mine began operation in 1994. It is located in northwestern Quebec, 20 km east of Val d’Or. The mine is owned by Aur Resources (30%), which operates the mine, Teck/Cominco (25%) and Novicourt (45%). By the end of 2002 there were approximately 280 employees working on the site, including contractors. Production averages 4300 tons per day, working a massive sulphide body located between 415 m and 920 m underground.Maintenance expenses represent 27% to 29% of the operating costs, and the maintenance personnel represents 34% of the total workforce (including electrical, mechanical and concentrator maintenance staff). Considering these figures, in addition to capital costs and indirect costs, such as energy (electricity, fuel, gas, etc.), it is worthwhile to pay attention to how things are done in order to protect such investment. Every task performed to help understand the impact of Louvicourt’s practices must to be seen as an investment in the reliability of its operation."

Jan 1, 2003

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By Glenn Davis

In the world of large scale open pit mining, the majority of a mines operating cost is tied to the removal and transportation of the overburden waste material. Typically, many large haul trucks are employed to transport this overburden from each excavating face. The trucks transfer the waste material from deep within the pit to waste dumps on the surface incurring significant costs in operators, road construction and maintenance, vehicle maintenance staff and support facilities, fuel, tires, and spare parts, as well as the capital cost of the truck fleet itself. In addition, the haulage of the actual mined material carries similar operational costs. In both cases, these costs grow as the mine face advances and pit haulage distances increase. Reducing truck haulage is one key to the success of the Dual Truck Mobile Sizer (DTMS). Being the world?s first fully mobile truck dump station, transportation costs can be significantly reduced as the mine face advances. Furthermore, when used in conjunction with a shiftable face conveyor and a mobile overland hopper, substantial cost savings can be achieved. The mobility of the system allows for the considerable reduction in the haul truck fleet. Overall mine site emissions levels are greatly reduced by the fleet elimination, as well as keeping the majority of the hauls on a flat grade within the pit. Emission levels on a typical truck will dramatically spike as the angle and the length of the haul are increased. Moreover, comparing diesel engines versus electric powered conveyors to move the material contributes to the realized savings.

May 1, 2010

By Bryan A. Bartley

"Jim Macdonald was promoted from Waterworks Engineer to Streetworks Engineer for the Wellington City Council. He thus took over the City quarry and responsibility for its performance. The crushing plant needed upgrading and he thought it would not be difficult to make a crusher to overcome a problem. If he had a longer association with the quarry industry he would have used conventional methods and equipment, so his invention arose from a fresh view of crushing.He invented the Barmac Rotopactor after observing a wear resistant chute with a lining of dead stone trapped above a piece of angle. This idea led to a rotor lined with trapped stone, rotating on a vertical spindle. In trying - a model rotor he observed the impact against a circular rill of stone in half an oil drum and thus was started a very fertile new area of developement in comminution. The writer helped in the developement and shares in the patents. Jim died in January 1982, just as the machine was becoming known and some 200 were in use in various countries. Most were working in hard rock quarries et that time but recent uses have carried the machine into the mining and mineral processing field. This paper is directed at that industry."

Jan 1, 1985

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003

By D. M. Doyle

"In this paper I will summarized the Falconbridge Nickel Mines1) energy costs and consumption data by fuel, process, cost centre and estimate our future costs and consumption patterns 2) detail the distribution of electrical energy 3) distribution of other forms of energy 4) describe present and planned energy conservation schemes; and 5) discuss economic justification and responsibility.There is sufficient material in this presentation to warrant several technical papers, however we felt that an overview of all our data and endeavors on the subject, would be most beneficial to those companies formulating energy conservation plans. The data briefly referred to in this slide presentation can be found in the technical paper.Over a five year period, total energy costs will vary between $63 and $94 MM depending on the future rate of energy cost escalation. An unrealistic 32% reduction in energy consumption is required to hold our own in the years ahead whereas an attainable 10°;, reduction in energy consumption would save $9 MM over this five year period.Total energy consumption, tonnage of ore delivered to plants and their ration BTU’s per ton of ore, are graphed for the years 1973 through 1976 and forecasted for the 1980’s. In 1974 we along with other member companies of the Mining Association, determined our purchased energy per ton consumption rate and set, as our goal, a 20% reduction by 1980. The dotted lines calculated from the energy audit, based on 1976 data shows there is a potential for a 10% increase in energy per ton. This could result from a lower than forecasted mining rate and operation of the new roasting, electric furnace and acid recovery facilities installed for environmental considerations at designed capacity."

Jan 1, 1978

By Zara Hosseini

?Microseismicity ?Seismic Systems ?Intrinsically Safe and Explosion Proof Seismic System ?Case studies: ?Gas Drainage Optimization ?Fault Identification ?Conclusion Seismic Event ?Occurrences in which energy is released in the rockmass creating a series of seismic waves propagating throughout the rockmass ?Can cause a Fall of Ground or CoalBurst Factors creating Seismicity: ?Mining at Depth ?High stress zones ?Major geological structures ?Mining practices and strategies ?Mining activities i.e. drilling and blasting

Aug 1, 2013

By Mark Sherman, M. Dennis, Raj Rajamani

"The two Alumbrera 36ft (10.97m)dia. SAG mills were sized, using the FDW ""Grindpower 'I program, to treat an average of 1852 tph each. This paper describes how modelling of the shell lifter design, using the Millsoft program, identified milling inefficiencies caused by poor charge motion. This explained the ""as built"" circuit's inability to achieve the throughput rates predcted by the circuit's designer. Use of the Millsoft program to design a new, dramatically different lifter configuration, in conjunction with a different approach to variable speed drive utilization, has resulted in an improved charge motion and a 30% increase in hard ore milling rates. The new lifter design has allowed the designer's predicted average throughput rates to be achieved.IntroductionThe Alumbrera project grinding circuit consists of two 36ft dia. X 17ft EGL, 13 500 kW, variable speed, gearless drive SAG mills coupled to four 20ft dia. X 30ft EGL, 6 000 kW fixed speed, gear driven, ball mills. The circuit is configured as two identical grinding aisles, each consisting of one SAG mill and two ball mills. No pebble crushing circuit was installed due to the expected absence of a critical size fraction in the first years of production. However, the grinding circuit layout does incorporate space for a pebble crushing retrofit. At present, only about 5% - 10% of the new mill feed reports as trommel oversize and is recycled back to each SAG mill using a water cannon.The circuit was designed to be ball mill limited and to treat the four major Alumbrera ore types at rates varying between 68 000 tpd, and 89 750 tpd, depending on ore hardness. Average throughput rate, and hence nominal design rate, for the grinding circuit was 80 000 tpd (1 852tph per line at 90% availability)."

Jan 1, 1999

By J. Dionne

"Next to the actual mine of Les Explorations Muscocho Ltée in Montauban, Quebéc, you could find a total of 364 000 tons of flotation tailings assaying 1.4 Au g/t et 82 g Ag/t to the south of the municipality. This tailings pile is what is left of previous operations. Preliminary leaching tests on these tailings in laboratory columns gave interesting results which led to tests in larger columns in 1984 and to a pilot test on a 750 ton heap in Montauban during the summer of 1985.This paper briefly describes the columns tests performed at the Centre de Recherches minérales and the heap leaching test designed and conducted by SOQUEM in Montauban. It also presents the results obtained.RESUMEPrès de la mine actuelle de Les Explorations Muscocho Ltée à Montauban, Quebéc, se trouvent, au pied du village, 364 000 tonnes de rejets de flottation titrant environ 1,4 g Au/t et 82 g Ag/t. Ce tonnage de rejets représente ce qui reste de l'opération des anciennes mines de Montauban.Des essais préliminaires de lixiviation en colonne sur ces rejets ont donné des résultats encourageants. Ils ont été suivis en 1984 par des essais en colonnes plus volumineuses et par un essai pilote à Montauban en 1985 sur une pile de rejets de 750 tonnes.Ce te x te donne une brève de script ion des essais en colonne effectues au Centre de Recherches minérales et de l’essai pilote planifie et exécute à Montauban par SOQUEM. Il présente les résultats obtenus."

Jan 1, 1987