Search Documents

By M. Epiney, A. Ghahreman, R. Kim1and

"Pre-oxidation and cyanide leaching behavior of gold in the presence of sulfide minerals were reviewed, focused on the effects of oxygen injection in the gold leaching process. Generally, pre-oxidation and gold leaching kinetics from iron sulfide refractory minerals, such as pyrite, pyrrhotite, marcasite, pentlandite and arsenopyrite, can be enhanced with higher dissolved oxygen (DO) concentration. However, most of copper sulfide minerals dissolved well both in water and cyanide solutions, and copper from the minerals consumed DO and cyanide to oxidize and leach. Only in the presence of chalcopyrite, gold leaching was effectively occurred with increasing DO. However, chalcocite and covellite severely retarded gold leaching. Stibnite, an antimony mineral, formed a passive film on the gold surface under any DO conditions, and it slowed gold leaching. This impeding effect can be alleviated by leaching at low pH or adding lead salt. Using oxygen and lead together can make synergistic effect in oxidation of sulfide minerals and can enhance gold extraction. Depending on the mineralogical characteristics of the ore, the optimum DO and lead concentrations can be optimized. However, lead can cause environmental problems, and so its dosage should be minimized or eliminated by substituting it with oxygen injection.INTRODUCTIONGold ores containing sulfide minerals are becoming more significant as high grade gold oxide deposits are continuously becoming difficult to find. In light of this situation, to produce more gold, recovery methods from refractory gold ore containing various sulfide minerals should be investigated. Generally, sulfide minerals have impeding effects on gold leaching: formation of a passive film on the gold surface, high consumption of chemicalssuch as cyanide and oxygenduring leaching, reduction of gold cyanide by sulfide ions, etc. (Senanayake, 2008). Therefore, sulfides must be properly treated for better gold recovery. Pre-oxidation of sulfide minerals by injecting pure oxygen can decrease the impeding effects in gold leaching. Prior to cyanidation, sulfide minerals can be oxidized to metal hydroxide and sulfate form, which consume negligible cyanide in the following cyanidation circuit (Bodnaras et al., 1993). Moreover, gold cyanidation can be enhanced by increasing concentration of the dissolved oxygen (DO). In general, the optimum concentration ratio of [CN-]/[O2] is calculated as 6, but it goes higher in the real system (Marsden &House, 2006), which means that the reaction is typically controlled by DO concentration."

Jan 1, 2017

By Gui Hua Wang, Xin Chang, Zhong Ying Han, Yuan Fang Cheng

"According to the geometrical characteristics of triangular meshes, Triangular Mesh Split Model (TMSM) based on a finite element method is proposed to simulate cracks propagation of fractured rock. With TMSM, stress intensity factors at the tip of cracks are obtained by far-field contour integral. Meanwhile, vector cross multiplication is adopted to fix the cracking unit, and maximum circumferential stress criterion is used to determine the crack propagation angle. Then crack dynamic propagation simulation is realized through local mesh split or node movement at crack tip. With this method, the crack can split apart a unit or extend along the mesh boundary, so the crack could extend along an arbitrary path and is not restricted by the initial mesh. The applicability of the mesh split algorithm is verified by the crack propagation examples of wing crack and multi-fractured rock mass with holes. The results show that this method not only has higher accuracy of fracture parameters calculation, but also can accurately simulate the crack initiation and propagation of rock under complex stress state such as tension, compression and shear. In addition, the far contour integral is introduced to determine the crack tip stress intensity factor and there is no need to reconstruct a singular element at the crack tip or to intensify the meshes. Compared with the existing mesh reconstruction algorithm, this method significantly improves the computational efficiency.INTRODUCTIONGenerally, rock is neither the full continuum, nor entirely discrete body, but rich in geological defects, such as joints and cracks. A large amount of geotechnical engineering practice shows that most fracture of rock is closely related to the internal joints, cracks and crack expansion (Horii et al., 1985; Wong et al., 1998). Although the classical theory of fracture mechanics established the theoretical foundation of crack initiation, propagation, so far it is still extremely difficult to characterize the propagation of airfoil-typed crack and the interference problem of multiple cracks. Up to now, the micromechanics mechanism research of crack propagation of fractured rocks has still been a hot research topic of rock fracture mechanics."

Jan 1, 2015

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD's , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977

By P. G. Smith, A. Axiuk

The objective of this paper is to present, from a practical perspective, a review of the most relevant maintenance procedures that are accepted or prescribed to be the most effective in optimising service life potential and to ensure continued safe use of steel wire ropes for shaft mining applications. The paper will address the most common operational issues encountered in the care and operation of shaft ropes for both conventional drum hoists and multi-rope friction winders. For each distinct maintenance procedure presented, a limited amount of theory is discussed to identify the underlying mechanisms at play that must be addressed and to emphasize the logical basis for the recommended course of action. It is recognised that each installation is unique and that the recommended maintenance procedures may not always be practical or cost effective from an operations standpoint under select circumstances, however the intent remains to promote industry best practices for the knowledge and benefit of the mine hoisting community, from experienced maintenance personnel to new entrants to the industry alike.

Jan 1, 2023

By G. J. Biefer

"Fatigue and corrosion fatigue measurements were carried out on five commercially available metals -four steels and an aluminum alloy -which are used as structural materials in mine shaft conveyances. In the corrosion fatigue measurements, drain waters collected in the shafts of three different Canadian mines were used as corrodents. The mine waters had been selected on the basis of their relatively large differences in acidity and/ or composition.It was found that the corrosion fatigue strengths of the four steels were similar, despite their differences in tensile properties, and that the type of water used in the tests had little effect on the results. Mild steel showed the highest and most consistent values of the damage ratio (ratio between the corrosion fatigue and the plain fatigue strengths at 107 cycles). The corrosion fatigue behaviour of the aluminum alloy (ASTM Type 6061-T6) was found to differ markedly in the three mine waters. A high damage ratio (i.e., superior performance) was shown in a mine water in which the corrosion attack was uniform; much lower damage ratios were shown in waters which produced localized corrosion attack. Corrosion rates were too low to be deter-mined conveniently by conventional weight-loss methods, but calculations from polarization curves provided a rapid demonstration that corrosion rates were distinctly lower in the mine water which produced high damage ratios."

Jan 1, 1967

By Pan Zhao, Yan-Nan Wang, Fei-Long Liao, Can Cai, Kai-Song Wu

"What are the basic physical parameters and main geometric parameters that are capable of representing the microscopic characteristics of rock? How can these parameters be used to accurately describe the macroscopic mechanical behavior of rock? With such questions in view, and based on the microcosmic structure analysis of rock slices, this paper presents a rock skeleton-pore structure model, holding that rock's mechanical behavior depends on the properties of rock skeleton materials and the form, size and distribution pattern of pores. According to rock stress and deformation behaviors, and in line with the skeleton-pore structure model, an essential mechanics theory for rock is advanced. The assumption that the skeleton materials are incompressible in volume and an introduction of logarithmic strain, generate the relation between porosity and apparent strain. Then, the notion that positive damage and negative damage are represented in terms of porosity is put forward; threshold value of porosity is derived by the damage threshold value of apparent volume strain; a general damage variable of rock is obtained; eventually, with the skeleton-pore model as the groundwork, a global damage constitutive equation is developed, which, with definite physical significance and material parameters to be easily determined, is convenient to apply. It has been proved that the results calculated with this new equation are well in agreement with experimental results.INTRODUCTIONRock is a form of material that contains pores, cracks and skeletons. Skeletons are composed of particles and cements. Pores or cracks within rock actually undermine the assumption of material continuum in solid mechanics. Hence, grave errors — or even false results — are inevitable if some solid mechanics theory is quoted in the discussion of rock mechanics. Many researchers in the field of rock mechanics have attempted various remedies, but the outcome is far from satisfactory — a mechanics theory for rock, in its true sense, has not been established."

Jan 1, 2015

By S. Aram

Concrete reinforcing requires coordination among many roles: structural engineer, estimator, detailer, fabricator, installer and others. The methods used to define and represent concrete reinforcement elements and assemblies in building information models is crucial in determining the efficiency of sharing data among BIM platforms and the effectiveness of using the carried data in production planning, fabrication and site work activities. Starting from the information items that are required to be provided by BIM platforms, as defined in earlier work, we have developed the Industry Foundation Classes (IFC) bound Concepts and Model View Definitions (MVDs) for concrete reinforcement. Furthermore, in coordination with software developers, we propose guidelines for best practices for concrete reinforcement modeling. Implementing these guidelines by software providers will improve reinforcement modeling with regard to various aspects of reinforcement products like geometric representation, placement, and property specifications. The proposed approach is selected as a way to improve functionality of the shared data for production planning, fabrication, project management, and site activities. Guidelines for assigning information to rebar type and instance definitions as well as to rebar elements and assemblies are provided. An efficient method of sharing geometry and property sets among rebar instances of a rebar array is also defined.

Aug 1, 2013

IN 1932, the No. 4 shaft at Wright-Hargreaves mine was completed to a depth of 4,000 feet, and the lowest operating level at that time was at 3,900 feet. It was realized that the existing pumping system, using triplex plunger pumps at somewhat irregular depths in the mine, would be in-adequate to take care of the increasing volume of water that would have to be handled as mining operations expanded. Accordingly, in February, 1932, after a thorough study of the whole matter, it was decided to instal an entirely new, automatically controlled, system of pumping, employing centrifugal pumps, with their characteristically trouble-free performance, operated by off-peak power.

Jan 1, 1939

By I. A. Tinto

"Labrador City is located in the southwestern portion of Newfoundland-Labrador, approximately 965 kilometers north-east of Montreal. The mine and beneficiation complex of the Iron Ore Company of Canada, known as the Carol Project, is situated 535 metres above sea level in a climatic region characterized by cold winters and short, cool summers.HistoryThe Iron Ore Company of Canada commenced work in the area in 19 4 9' however, it was not until 1958 that the decision was made to proceed with mining operations. The ore body consists of Specular Hematite (Fe203) and Magnetite (Fe304) with small quantities of Limonite and Geothite. The average grade of the ore bodies is 39% iron.The mining facilities, crushing plant, and concentrator were in operation by the early part of 1962. In the summer of 1961, a decision was made to build a pelletizing plant adjacent to the concentrator. This plant was designed, erected and placed in operation during 1962 and the first half of 1963. Since the completion of the pelletizing plant, additional expansions to both the pellet plant and concentrator have taken place in 1967 and 1973. Today, the Carol Project has the capacity to produce 20 million tonnes of concentrate from which 10.5 million tonnes of pellets can be produced.The period 1980-85 spans a period of energy crisis, world-wide recession, and a consequent re-structuring of the North American steel industry as it struggles to survive in an arena of excess world steel making capacity, government subsidized industries, and the increasing competition from overseas and from developing countries.The media headlines over the past few years echo the woes of the industry and the strategy plans for survival of the fittest. Today's buzz words are foreign competition, steel import quotas, joint ventures, employee participation, work rules, quality, productivity, and state of the art technology."

Jan 1, 1986

By David G. Meadows

During the last decade Antofagasta Minerals? Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.

Jan 1, 2012

By W. G. Stevenson

With the author's background of extensive experience, this paper delineates the role of the prospector in modern-day exploration programs. The stages in the development of a prospect to a producing mineral district are outlined, and examples are given from the Ross River area of the Yukon Territory and the Peachland and Highland Valley areas of British Columbia.

Jan 1, 1970

By S. Y. Ezz, K. El•Guindi

A vertical tube, 8 m long and 2.5 cm in diameter, electrically heated to 650°C throughout the majority of its height, was used to study the-effect of ore feed rate and hydrogen flow rate on the reduction of fine iron ore particles. A correlation could be obtained between the combined effect of the amount of reducing gas and reduction time and the per-cent reduction. The results suggest that a method based on the reduction of fine iron ores while falling through up-streaming hydrogen cannot be recommended for industrial application.

Jan 1, 1969

By F. A. Auld

"Traditionally deep shaft sinking from the ground surface was carried out using drill and blast methods. Although large diameter blind shaft drilling has been carried out successfully on numerous occasions previously, including as early as 1852 in Germany (Auld, 1995), little attempt has been made until more recently to mechanise the shaft sinking excavation process using down-the-hole machines. This paper reviews the development of deep shaft sinking machines from the early 1970’s up to the present day. INTRODUCTION Mechanical excavation methods can significantly improve excavation performance, in order to access natural resources faster, and labour safety is increased compared to drill and blast operations. However, shaft sinking machines need to be capable of accommodating all the basic requirements for deep shaft sinking, namely: 1. Excavation and muck removal 2. Ground stability control 3. Groundwater ingress control 4. Temporary lining installation 5. Permanent lining installation and watertight sealing 6. Ventilation 7. Secondary means of egress for personnel In addition, how the machine operates in the shaft is an important factor, either slung on ropes from a surface headgear or on its own in the bottom of the shaft. An all-embracing machine which can deal with all of the above conditions is impossible but many of these requirements can be incorporated into a single machine. Deep shaft sinking also differs greatly from normal tunnel construction which employs the use of either a roadheader arm installed within a shield or a full-face tunnelling machine for excavation. Hydrostatic pressure and ground stability problems increase with depth, whereas in tunnelling the depth is normally relatively shallow and the aforementioned factors remain approximately constant along the tunnel length. DEEP SHAFT SINKING MACHINES All the shaft sinking carried out previously in the UK was by the traditional method of drill and blast. Elsewhere, in other parts of the world, attempts have been made to mechanise the process."

Jan 1, 2019

By S. M. Grillo, Fiori. M., R. Bornioli, C. Marini, S. Fadda

Abstract - The Na-feldspar orebodies in Sardinia occur along structures belonging to a regional ENE-WSW system that developed during the late stages of the Hercynian orogeny, and that was reactived during the Alpine orogeny. The main petrographic facies include granitoids, albitized granitoids, albitites (more or less rich in quartz), and albitites containing Mg minerals. Field observations and petrological and geochemical data point toward a metasomatic origin for the albitite orebodies. Albitization involved depletion of K from K-feldspar and biotite, dissolution of free quartz, and a lowering of Sr/Na2O and CaO/Na2O ratios in the protolith, under conditions of a positive thermal gradient. The absence of later K-metasomatism implies that, during a subsequent decline in temper- ature, the composition of the albitizing fluids was modified by an influx of meteoric or other waters.

Jan 1, 1996

By S. M. Grillo, M. Fiori, R. Bornioli, C. Marini, S. Fadda

The Na-feldspar orebodies in Sardinia occur along structures belonging to a regional ENE-WSW system that developed during the late stages of the Hercynian orogeny, and that was reactived during the Alpine orogeny. The main petrographic facies include granitoids, albitized granitoids, albitites (more or less rich in quartz), and albitites containing Mg minerals. Field observations and petrological and geochemical data point toward a metasomatic origin for the albitite orebodies. Albitization involved depletion of K from K-feldspar and biotite, dissolution of free quartz, and a lowering of Sr/Na2O and CaO/Na2O ratios in the protolith, under conditions of a positive thermal gradient. The absence of later K-metasomatism implies that, during a subsequent decline in temperature, the composition of the albitizing fuids was modified by an influx of meteoric or other waters. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1997

By Maureen Jensen

For mining companies looking to establish a strong North American presence, raise their profile or finance and position themselves for future growth, there is no other destination in the world that can offer a mining company the same opportunities as Canada whether you are an established blue chip or promising junior. Despite historically poor world commodity markets and shaky investor sentiment towards junior explorers caused in part by fallout from the high profile Bre-X fraud, Canada continues to shine as the undisputed mining finance capital of the world. Our natural riches and mining history go a long way to explain Canada's international prominence in mining finance. Canada has actively created and maintained one of the most integrated national frameworks to support mining ventures of all kinds. Our diverse industry, from one-person grass-roots explorers to mining industry giants, is one of our main strengths whether your company is Canada-focused or internationally active. The mining industry continues to be a vital contributor to the Canadian economy, contributing $26.2 billion in 1997 or 3.8% of national GDP, and is the second largest earner of foreign exchange. Industrial mineral companies are a very important part of this strength. These companies require a continuing access to capital to ensure that they can continue to compete and the globalisation of the Canadian mining industry has affected this industry just as much as it has affected every other industry in Canada.

Jan 1, 2001

By B. Zeifert, C. Martínez-Morales, A. Romero-Serrano, A. Pineda-Rivera, H. Martínez-Gutiérrez, G. Diaz-Sandi

In this work, the effects of CaO/SiO2 ratio and the FeSO4 and FeS2 contents on the stability of the mineralogical species in chromium-based slags were studied. The chemical stability was evaluated by leaching with an acid solution. The main Cr-compounds in slags with FeSO4 and CaO/SiO2=1 were FeCr2O4 and Ca3Cr2Si3O12, while Cr3S4 predominated in slags with FeS2. The slags with CaO/SiO2=2 mainly contained CaCr2O4. The highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO2= 2, and the lowest Cr concentration corresponded to slags with high FeSO4 or FeS2, owing to the stable binding of chromium in the compounds FeCr2O4, Cr3S4 and FeS•Cr2O3.

Jan 1, 2011

By S. V. Ulianov, A. Y. Senchenko, E. M. Kurchevskaya

"A process sample of old copper-containing tailings (-2.0+0 mm) from an iron-ore plant was tested in TOMS institute in order to develop a process for copper concentrate production. The study of tailings material composition indicated that -0.2+0 mm fraction was efficient and contained 97.26% of copper. Copper is predominantly concentrated in chalcopyrite which is present both in free form and in intergrowth with ore and rock-forming minerals. Study of chalcopyrite using an optical microscope and Qemscan SEM determined that the most grains surface was covered with oxide films. Additionally, a lot of grains had micropores on their surfaces that indicated a partial mineral leaching. The oxide films did not make it possible to float copper minerals from head material. It was recommended to apply an attrition operation to restore chalcopyrite floatability. In order to increase selectivity a regrinding stage for a primary copper concentrate was introduced to obtain P80 26 um. Taking these recommendations into account a flotation flowsheet was developed to process the old Cu-containing tailings. The flowsheet allowed us to obtain a concentrate with 23.5% Cu content at 71.5% recovery.INTRODUCTIONStudy of material composition is an important prerequisite for development of a minerals processing technology. Mineralogical study contributes to search for an efficient technology to recover valuables and for prospective methods of minerals processing.The use of such up-to-date analysis methods and equipment as Qemscan and Mineral-C7 allows one to determine minerals size, liberation degree, and mineral associations. Mineralogical data can reveal reasons for hard processing of minerals prior to development of the process.The advanced process mineralogical methods used to study Cu-bearing pond tailings indicated several factors that influenced development of the process. The first one is a barren size fraction which is to be removed from the process in order to considerably reduce the costs connected with grinding. The second is the presence of films on chalcopyrite surface; in this context, a preliminary attrition of the material was recommended. The third factor is finely disseminated Cu minerals in sulphide and in the rock, which predetermined selection of particle size for flotation. All these data led to significant decrease in time required to develop the process technology. The developed process flowsheet based on the obtained mineralogical data is present in Figure 1."

Jan 1, 2016