Search Documents

By Jan Kvinge, Aina Opsal Bakke, Yanjun Li, Jan-Ove Løland, Svein Jørgensen

"Compound casting is a very attractive approach to reduce the weight of components for some specific applications while keep both the functional and the mechanical property requirements. In this work, Al-7Si-Mg alloy /copper compound castings were produced through a low pressure die casting process. To reduce the oxide present in the interface, flux coating of the copper pipes was tested. The interface layer formed between the two alloys was investigated using Optical Microscopy (OM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Vickers Micro-hardness was also measured across the interface. Results showed that the flux coating prevented the formation of the metallic bond between copper and aluminum. Instead, high concentrations of potassium, magnesium and fluoride, coinciding with formation of KMgF3 and MgF2, were detected in the interface. In the castings without surface treatment, a continuous metallurgical bond was achieved. In the bond layer, various Al-Cu intermetallic phases have been detected. In addition, formation of primary silicon particles in the reaction layer was observed in all castings. The mechanism for the formation of the intermetallic phases and the strength of the interface layer have been discussed.INTRODUCTION Recent development in the automotive industry has focused on producing lightweight components, which can reduce CO2 emission and increase the efficiency. Often, one material alone is not able to meet the requirements for a specific use. The need for lightweight bimetallic components has therefore increased. Aluminum-copper bimetallic components can be used in wires and bus bars where conductivity is an important factor (Lee, Bang, & Jung, 2005). Compared to Al-Cu alloys, Al-Cu bimetallic components can reduce both weight and cost without reducing electrical and thermal conductivity (Sheng, Yang, Xi, Lai, & Ye, 2011). A challenge is, however, that aluminum and copper have high affinity to each other, especially at elevated temperatures. This causes formation of brittle intermetallic phases with high electric resistance (Liu, Wang, Sui, Wang, & Wenjiang, 2016). In addition, both metals are subjected to oxide formation on the surface. Copper is especially exposed to oxidation at elevated temperatures (Pinnel, Tompkins, & Heath, 1979), while a thermodynamically stable oxide layer will spontaneously form on the aluminum surface (Papis, Loeffler, & Uggowitzer, 2009). Oxides are known to be passive substrates, which will reduce wettability and will thus prevent the formation of metallic bonding between aluminum and copper (Papis, Hallstedt, Löffler, & Uggowitzer, 2008)."

Jan 1, 2018

By Brian W. Mackenkzie, Jozef Lajzerowicz

This paper is intended to familiarize planners in the noncommunist world with the district planning approach used in eastern Europe for mining development. It deals generally with the basic nature of the district planning problem, the planning process for mining development and the state organization for the planning of mining districts. A number of applications of district planning techniques to both established and new eastern European mining districts are described.

Jan 1, 1971

By G. G. Manekar

MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprise, under the Ministry of Steel, Government of India, produces about 1.1 million tonnes (T) of manganese ore annually from three opencast and seven underground mines. The underground operations are mining using an overhand cut and fill method. The orebody is too narrow for the use of larger equipment and the poor to fair rock mass quality limits the size of stable excavations. Prior to the 1990s underground support consisted primarily of timber square sets in tandem with timber chocks and props. As mine production requirements increased throughout the 1990s led to larger opening sizes and more modern support practices. Research was conducted on ground support design based on rock classification and empirical techniques for designing ground support. Based on the findings and field trials, the Company adopted full column cement grouted cable bolts for back support. Instrumented field trials, using extensometers and load cells on the cable support confirmed the support effectiveness. Stope design was based on two and three dimensional stress modeling which resulted in a significant increase in stope dimensions. The rock mechanics studies for safe stope design were carried out using numerical modeling tool in two and three dimensions for the analysis of stresses. Based on the findings, the safe stope geometry with new stoping parameters was introduced. The earlier stope length of 30 mtrs were changed to 60 mtrs with in situ rib pillar at the cross cuts and in situ post pillars to be left-out in the stope. This leads the formation of of panel comprising of three stopes, for production, supporting and filling. For mechanical handling of ROM in stopes Side Discharge Loaders (SDL) were introduced. The above changes have improved the face productivity from 2?3.5 T with manual operation and 9 T with SDL. The above rapid mining operations has improved the stope productivity but reduced the stope life from 6 to 3 years. For the improvement of the stope availability, further studies were conducted by numerical modeling of stress analysis. The related studies confirmed that with the existing supporting system and proper instrumentation, level interval could be increased up to 45 mtrs from the existing 30 mtrs at deeper levels. At present below 12th Level interval is 45 m at Balaghat Mine. For future mechanization program for introduction of Single Boomers, LPDT, Cutting Machines etc for the development headings rock mechanics studies are underway. The paper provides details of rock mechanics studies that were carried out to study efficacy of the cable bolt support, safe stoping parameters and increased level interval for the improvements in safety, production and productivity at Balaghat Mine.

Aug 1, 2013

By L. K. Sinclair

In situ leaching of copper has the potential to deliver low-cost recovery for soluble copper deposits of sufficient permeability. In order to provide key inputs for modeling of the in situ leaching process, bench scale test work can be used in conjunction with geochemical software to identify key leaching and precipitation reactions. A case study is presented in which a series of flow-through acid leaching tests were conducted on drill core sections from a porphyry copper deposit without crushing or grinding. Concentrations of copper and other key elements were monitored in the recirculating leach solution over several months. A geochemical model of each leaching test was prepared using Geochemist's Workbench using a combination of diffusion-controlled and reaction-controlled rate mechanisms. Key reactions included leaching of chrysocolla, iron oxides, and plagioclase. The model was able to simultaneously satisfy the evolving chemistry of the recirculating leach solution, mineralogy of the head and leach residue, measured acid consumption, and leaching rates for key minerals reported from previous laboratory studies. Opportunities and limitations for scaling up the model to simulate the commercial wellfield are discussed.

Jan 1, 2015

By Xiaozhu Chen, Qi Ping, Pu Yuan, Qinyong Ma

"In order to investigate the fractal feature of coalmine deep rock fragments under impact loads, variable cross-section split Hopkinson pressure bar apparatus, 50 mm in diameter, was adopted to conduct impact compressive test for rock specimens from -962m deep coalmine. Various impact pressures, such as 0.3, 0.6, 0.9 and 1.2MPa, were selected to implement different loading rates. Sieving statistical analyses were conducted for rock fragments after being impacted, and the particle size distribution of broken rock in various loading rates were calculated with the fractal method and then the corresponding fractal dimension was obtained. Test results shows that there is a good self-similarity and fractal feature in fragments distribution of deep coalmine sandstone under impact loads. The fractal dimension of fragments is between 1.9 and 2.7. The research also indicates that there is an approximate power relationship between dynamic compressive strength and fractal dimension, and a strength power relationship between fractal dimension and average strain rate. Moreover, there is a linear relationship between fractal dimension and specimen absorbed energy. The rock fractured process can be quantitatively described through fractal dimension, which can reflect the deep rock broken degree and is an ideal index to evaluate the distribution of rock fragments.INTRODUCTIONBroken rock is one of the most basic processes in mining operations, rock fragmentation has always been an important index to evaluate rock breaking effect (Xu & Yu, 1984). Macroscopic fragmentation of rock material is the final results of continuous development, expansion, gathering and cutthrough of internal micro-cracks. This process, developing from microscopic damage to macroscopic fragmentation, is an energy dissipation process and shows fractal characteristics (Xie, 1993). Turcotte (1986) has conducted statistical analyses of fragmentation for different kinds of geological materials under various broken conditions, and arrived at the conclusion that fragmentation distribution is a fractal."

Jan 1, 2015

By S. C. Ellis

THE bituminous sand of northern Alberta has already an extensive literature, and most of the reports dealing with the subject are still available (see Selected Bibliography at end of paper). A phenomenon so striking and, as regards its extent, so unique, as the deposit in the vicinity of McMurray settlement could not fail to attract the notice of the early explorers, and we find references to it as far back as the latter part of the eighteenth century. However, scarcely a thought had been bestowed upon the possible economic value of minerals in the the remote northern parts of Canada before the second decade of the present century, and practically no detailed mapping had been done north of the town of Athabaska. The late Wm. Ogilvie made a track survey of Athabaska river in 1884, and surveys of certain lines-including the 23rd base line-had been completed by 1911. Between this base line and lake Athabaska, nothing had been attempted. Actually, no definite information at all was available regarding the character and extent of the bituminous sand when, in the earl y summer of 1913, a reconnaissance party set out from Athabaska for McMurray. At that period, the journey was made in summer by scow or canoe. No telegraph line had been laid, and a casual mail service by canoe or dog team once in three months formed the only means of communication with the outside world. The investigation has begun by the Mines Branch was continued during several subsequent years. The sand deposits were studied and sampled, the bi rumen was extracted from the sand and studied chemically and physically, and the economic significance of the deposit was given exhaustive study.

Jan 1, 1937

By 000-900-009-492

The flotation has been and is still the most widely used mineral concentration method. Because of its complexity, the flotation process required the development of robust control strategies which was facilitated by the introduction of on-line sensing instruments such as x-ray fluorescence (XRF) on stream analyzer (OSA), gamma density gauges and electromagnetic flowmeters. The interest in developing control strategies has persisted because the benefits to be gained in terms of improved metallurgical performance are substantial. As the flotation control becomes more and more difficult due to the emergence of low grade and complex ore cases, other control strategies have to be introduced. Froth based control is one of the emerging useful control strategy This paper will focus on the state of the art in the on-line froth characterization as obtained by numerical image analysis. The technology of machine vision provides a novel solution to several of the problems encountered in conventional flotation systems for monitoring and control, and constitutes a powerful tool for the investigation and interpretation of the effect of various flotation parameters as driven for the froth phases. Copyright @2001CIM

May 1, 2001

By L. H. Thorleifson

Demand for both gem and industrial diamonds is very strong. Synthetic production supplies industrial uses, but synthetic gems remain inferior and expensive, so the large gem market is supplied by mining. Several major mines have been depleted, and the market is receptive to new sources of high quality gems. Canada's Precambrian terrane, extending across the Canadian Shield and under the Phanerozoic cover of the Plains and Hudson Bay, has excellent potential for diamonds, but exploration conditions are difficult due to recent glaciation. Early world exploration relying on recognition of diamond in alluvial sediments was adequate to launch pre- 1900 production from India, Brazil, and Africa. Exploration success in Canada, as was the case in Russia and other more recently discovered sources, however, had to await large investments in effort supported by advanced science and technology. Canadian exploration in many ways is similar to that in other regions, relying on analysis of tectonics, indicator minerals, geophysical surveys, and multiple stages of drilling and sampling. Very different from other regions, however, is Canada's surficial environment, in which recent glaciation has caused fresh indicator minerals to be transported hundreds of km. Exploration accelerated in Canada after 1960, first in Ontario and the Arctic Islands, then in Saskatchewan in 1988, and most importantly after the Chuck Fipke - Stew Blusson discovery at Lac de Gras, Northwest Territories, in 1991 that led to the billion-dollar BHP - Dia Met Ekati Mine that opened in 1998. In 2003, production from Ekati will be supplemented by that from the similar and nearby Diavik Mine of Rio Tinto and Aber. These mines will bring Canadian output to over 10% of world supply, and will position Canada with Botswana and Russia as world leaders in production of high quality gem diamonds. There could be other mines as well, as sites across the Arctic and in the south from Alberta to Québec are being explored by an array of companies, including De Beers, other majors, and several juniors.

May 1, 2003

By G. R. Tostengard

"The paper identifies functional areas which frequently can yield significant productivity improvement. Emphasis is placed on the repair and maintenance, material supply and training functions. Successful approaches are discussed in some detail, and typical results which have been achieved are reviewed.IntroductionA challenge which at all times confronts the manager o f any mineral operation is the potential to improve his operation no matter how effective it might be a t the present time. The challenge has been present through my entire lifetime and I suspect a good many years prior to that and, I expect, will continue many year s and decades in the future. The competitive and economic situation in which we in the minerals industry find ourselves today makes the challenge eve n more important during the 1980s. In many cases it’s a question of survival, not simply pr of it improvement.There are, of course, many avenues to improving profitability; technological changes, new equipment and facilities, improved products, improved mine plans, etc. All of these are important and must be addressed by each manager. This paper focusses on just one avenue to improvement and that is ""improved management"", not so much of management at the boardroom level but of improved management o f the facilities and workforce as the y currently exist. Management implies control. There are three areas where control is often found lacking:1, Repair and maintenance of equipment and facilities;2. Material supply including procurement, inventory control and warehousing; and3. Training.These three areas are all complex and difficult to manage and they are all but ignored in the formal education which our industry's manager s normally receive. They are areas which can be improved with relatively small investments and therefore, they represent especially attractive improvement targets during the 80s when, for most of us, investment dollars are very difficult to come by."

Jan 1, 1983

By M. Mezbahul-Islam

Thermodynamic modeling of the Mg-Cu-Ni system is carried out as a part of multi component thermodynamic database for Mg alloys. This system is being modeled for the first time using the modified quasichemical model, which considers the presence of short range ordering in the liquid. The thermodynamic descriptions of the binaries Mg-Cu, Cu-Ni and Mg-Ni have been extrapolated to the ternary Mg-Cu-Ni system using Toop geometric model. The constructed database has been used to calculate and predict thermodynamic properties, isothermal sections and liquidus projections of the Mg¬Cu-Ni system, which showed very good consistency with the experimental data.

Jan 1, 2011

By Yoshimasa Funakawa, Kazuhiro Seto, Akio Kobayashi

A new hot rolled high strength steel consisting of ferrite matrix and nanometer¬sized precipitates was developed. The ultra fine precipitates were identified as TiMoC2, and the strengthening by the precipitates was evaluated more than 300MPa in case of TS/800MPa grade steel. Due to the strengthening effect of the ultra fine precipitates, alloy elements for solid solution hardening can be reduced. It is notable that the steel shows very high yield strength (730MPa in case of TS/800MPa) and very high local elongation leading to excellent stretch flange formability at the same time. The mechanical properties of the steel are attractive for chassis parts and structural parts of auto body. The steel has been produced commercially, and applied to the parts successfully.

Jan 1, 2004

By Z. Trojanová

Mg micropowders generated by gas atomisation of a magnesium melt with argon were mixed and ball milled with ceramic nanoparticles prepared by laser-induced gas phase reaction. The materials were then hot extruded. Specimens were deformed in tensile as well as compression tests at temperatures between 20 and 300 °C at a constant initial strain rate. The flow stress is significantly influenced by the test temperature. The yield stress decreases with temperature. This decrease and the flat character of the stressstrain curves at elevated temperatures indicate possible contributions of softening processes. The materials studied exhibit high-damping characteristics. The results are analysed and possible mechanisms are discussed.

Jan 1, 2006

By G. K. Quainoo

In the automotive industry, the awareness to meet Corporate Average Fuel Efficiency (CAFE) standards has evolved the need to reduce vehicular weight in new automobile designs, with the overall goal of reducing gas emissions into the atmosphere (Kyoto protocol), One efficient method has been to use lighter materials such as aluminum in outer body panels, Heat treatable AA6111 is one of the materials employed due to its unique combination of formability, paint bake strengthening and superior corrosion resistance characteristics, Researchers have applied various thermo-mechanical processes on 6000 series aluminum alloys and have found an improvement in the mechanical properties of these alloys, For a formed and painted automobile panel, the final mechanical properties involve a combination of strength components arising from cold work, strain aging and precipitation minus recovery. In this study, the evolution of microstructure resulting from the interaction of cold work and precipitation in AA6111 has been studied by means of transmission electron microscopy (TEM) after subjecting samples to various heat treatments, tensile testing and differential scanning calorimetry (DSC), This has been done to understand the evolution of microstructure and its influence on the properties of the alloy, The results show a considerable improvement in strength with a corresponding increase in strengthening precipitates with increasing level of cold work in the alloy. DSC results following the application of various levels of cold work also show acceleration in the precipitate phase formation, as precipitates are observed to form at lower temperatures, with increasing level of cold work/

Jan 1, 2005

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By H. Salomon-de-Friedberg

The amount of pyrite in copper concentrates fed to the CESL Process can vary appreciably. The fraction of pyrite that oxidizes influences both capital and operating costs and is therefore an important variable. The present paper explores operating conditions that influence the extent of pyrite oxidation and the probable overall reaction chemistry under CESL conditions.

Jan 1, 2014

By Robert L. Tremblay

Dans le but de voir si une région comme la Gaspésie, qui a subi la derniere glaciation , se prête avantageusement à la méthode de prospection alluvionnaire, environ 800 concentrés de minéraux lourds furent prélevés dans les districts électoraux de Matane et de Gaspé-Nord. Les différentes phases minérales présentes dans les concentrés ont été examinées à la loupe binoculaire. Afin de mieux valoriser ce type d'inforrnat ion, nous avons été arnenés à expérimenter et à mettre en oeuvre des techniques multivariables adaptées au traltement d'une information semi-quantitative en utilisant le principe d'un codage logique préalable. La structuration des résultats de la Gaspésie a conduit à l'élaboration de cartes de synthèse qui constituent un support nécessaire à l'interprétatlon des répartitions plus ponctuelles des minéraux "utiles" sur le plan de la recherche minière.

Jan 1, 1978

By B. Fang

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment, The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate, The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB?s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By A. M. Abdel-Rehim

The present work reports a study of production of thorium concentrate from Egyptian monazite by decomposition of ammonium carbonate solutions containing ammonium thorium and uranyl carbonate complexes. These solutions were obtained from the processing of monazite by alkaline leaching in ball-mill autoclaves, followed by selective separation of thorium and uranium from lanthanides by autoclave leaching of the hydroxide cake obtained with ammonium carbonate - bicarbonate solutions. The separation of thorium and uranium in the form of thorium concentrate from their carbonate complexes was achieved by different methods, including neutralization of solutions at pH = 6.7 by acid, addition of alkali at pH = 11.5, heating of solution at 100°C and processing of carbonate solution with steam under pressure in steel autoclaves. Processing of solutions of thorium and uranyl carbonate complexes in an autoclave with steam causes their decomposition. Complete recovery of thorium 99.8% and 98.4% uranium recovery in thorium concentrate was attained at 120°C and steam pressure 2 atm, within 10 min. Meanwhile, the recovery of lanthanides was low and did not exceed 1.1%. The thorium concentrate produced contains 67.82% Th, 4.6% U and 3.14% REE. All methods achieve complete separation of thorium and uranium from their carbonate solutions, but the first two methods are unfavourable for the industry due to the high cost of reagents and their inability to regenerate the ammonium carbonate. The decomposition of ammonium thorium and uranyl carbonate complexes with steam under pressure is recommended for industrial application for its simplicity and the ability to regenerate the ammonium carbonate.

Jan 1, 2004

By H. J. McQueen

Mineral and energy resource consumption were continuously reduced by process improvements as chemical understanding was developed and applied. During the past two centuries, technological improvements increased human productivity that was accompanied by social advances and labour saving products; however, these sometimes proliferated to endanger sustainability, e.g., automobiles. In the steel industry, precisely controlled rolling of HSLA steels required little extra mineral consumption but reduced weight and heat-treating energy. Continuous casting of slabs reduced scrap compared to ingots and energy for the homogenizing soaking pit. Al alloy extrusions were improved by retaining the strengthening in the near-surface substructure, of high strength textures and of press quenching that is suitable for direct age hardening. Continuous bar casting of Al-0.65Fe, coupled with rod rolling and followed by wire drawing with only a final recovery anneal, yielded electrical wiring for households to replace less plentiful Cu and later for light-weighting use in autos and aircraft Looking backwards, the 1970 decade saw the first oil crisis and inspired Ottawa to undertake a campaign to develop an energy strategy that would decrease dependence on imported fuels. One significant undertaking under Energy Mines and Resources was the organization of industrial energy conservation, managed by each industry association,that collected detailed current statistics and set the goals for a 2-year campaign. The metal producing industries, as compared by E.C.N. Perryman to about 7.2 exajoules (EJ) for the nation, consumed about 0.8 EJ, being about one third of all heavy industries. While manufacturing consumed 30.2% of total energy, it created 87.3% of total national dollar value. Within the industrial envelope, smelting and refining utilized 28% (0.67 EJ, mining beneficiation 6.7%, 0.16 EJ); there was a significant contribution to exports: 80% of iron ore and 70% of aluminium in 1973. A general concern was that decreases in ore grade would lead to a rise in energy expenditures countering benefits from processing efficiency.

Jan 1, 2012