Search Documents

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By O. Moselhi

Material can be seen as the fuel needed to execute the project from inception to completion. Material installed provides good indicators of progress achieved onsite vis-a-vis project schedule performance. It correlates well with the role of the schedule performance index (SPI) of the earned value method (EVM). Material is recognized to have a significant impact on achieved progress for physical completion of project activities. This paper presents a study on the development of material status index (MSI) in support of the EVM. Unlike the SPI, the newly developed index account for the criticality of project activities. This is carried out considering the total float of each activity, percent float (i.e. the ratio of float to activity duration) and the total float of the path on which the activity is located. MSI, can independently and jointly with SPI provide root causes behind problems encountered during project execution. In turn MSI can reveal material related factors behind the performance detected by joint interpretation of the two indices. MSI serves to provide added value in alerting management to take corrective actions. While SPI and MSI may have different values, they can jointly augment and enrich the captured project status based on EVM. To demonstrate the capabilities of the developed MSI method, it is implemented on a case study. The case encompasses the construction schedule of a hydro power station constructed in northern Quebec. Different scenarios are adapted from the real case to demonstrate a set of practical aspects of the developed index. The results generated from the analysis of the case study illustrate the useful features of MSI beyond those of the traditional SPI on two fronts; causation and the considerations of criticalities of actives.

Aug 1, 2013

By Gordon. I. M., J. Blackshaw

"The wet part of the Hollinger mill is housed in two buildings, the grinding plant and the treatment plant. In the grinding plant there are four 7xl5 ball mills which grind the ore to 60 per cent through 200 mesh. There is also one 7xl5 ball mill which grinds table concentrate to 9 5 per cent through 200 mesh.The primary classifier overflow is pumped to the treatment plant where it passes over shaking tables, producing a concentrate and a tail. The concentrate pulp is pumped to the grinding plant for secondary grinding. The secondary classifier overflow is pumped back to the treatment plant where it is thickened in two 40xl 5 tray thickeners and agitated in four 20x24 mechanical agitators arranged in series of two (with 2 spares).The table tail pulp is thickened in nine primary 40xl5 tray thickeners (with 2 spares). The thickened table tail pulp and the concentrate agitator discharge pulp are mixed and pumped to four rows of 15x45 pachuca agitators, arranged in series of five tanks.The pachuca discharge pulp is divided. The smaller part goes to two rows of 3-step decantation using 40xl5 tray thickeners (with 2 spare rows). The larger part goes to six 14xl6 drum filters. The repulped primary filter cake and the thickened pulp discharged from the decantation rows are fed to eight 14xl6 drum filters. The secondary filter cake is mixed with water and pumped to the tailing line."

Jan 1, 1968

By J. Clark

Erosion control during the mining cycle can be more effectively planned using Erosion and Sedimentation Control Plans (ESCPs). This raises the issue of who should develop an Erosion and Sedimentation Control Plan Guidance document (ESCPG) to standardize the content of ESCPs. A search for ESCPG documents in Canada revealed no examples for mine sites. In the U.S. there are a number of regulatory authorities who developed such documents for mine sites, including EPA. An ESCPG is expected to result in: (a) plans will be more standardized (b) more clarity and efficiency for those generating ESCPs; (c) assisting regulators tasked with reviewing/approving ESCPs; (d) providing guidance for the mine effluent permitting process relative to sediment control; (e) providing a basis for developing and including ESCPs in the Environmental Assessment (EA) phase and the mine economic assessment; (f) applying and optimizing ESCPs above the ?watersheds? of sediment ponds; (g) utilizing the ESCPG document for ?exploration? sites; (h) lowering the risk of adversely impacting water quality downstream of mining activities; (i) providing a methodology for determining the need for sedimentation pond(s) during the construction and production phases; and (j) providing a clear environmental sustainability message relative to sediment control if the mining industry takes the lead in developing an ESCPG. ESCPs will proactively create increased administrative (regulatory) efficiency in the EA and sub-EA reviews relative to erosion control and sediment release from mine sites. This also assists the new initiative in BC, One Project, One Process (OPOP) and synchronous permitting (a variation of concurrent permitting): as an example, enhanced erosion control planning at the EA phase then allows the synchronous permitting initiative to proceed efficiently, particularly for the mine permit (Ministry of Energy, Mines and Natural Gas) and effluent permit (Ministry of Environment). Approximately twenty more management plans (e.g. ARD/ML, explosive management, emergency response, hazardous waste, sediment pond operation, environmental effects, environmental sampling, etc.) may also be entered into the EA process to create increased efficiency, and then feed into the synchronous permitting effort. The BC OPOP initiative also adds support to the Canadian Federal ?One Project, One Review Process? approach. The ESCP and a sediment pond management plan will also address the Canadian Metal Mining Effluent Regulations requirement for all discharges from mine sites to meet a grab sample of 30 mg/L Total Suspended Solids.

Aug 1, 2013

By S. Broda

Waste rock piles (WRP) are made of heterogeneous, coarse grained waste rock, with inclined layers due to segregation along the slopes and haul traffic compacted layers, creating highly contrasted hydrogeological conditions. The internal structure of the pile has a major impact on water and oxygen movement and pore water pressure distribution. In the presence of reactive minerals, this influences the production of acid mine drainage (AMD) or contaminated neutral drainage (CND) with metal leaching from the WRP. Water flow and distribution may also affect slope stability, particularly following major infiltration events (rain/snow melts).The prediction and interpretation of water distribution in WRP is a challenging problem. Numerous numerical investigations of short and long term forecasts have been conducted, and many of these were found of limited reliability. The shortcomings of existing approaches are typically due to difficulties in representing preferential flow processes in macropores. Such phenomena are in fact often neglected in the assessment of water flow in WRP because these are unattainable with the classical porous media approach typically used in this field. This paper focuses on the use of modeling techniques originally designed for massive fractured rock media to simulate flow in WRP. Waste rock properties used in this study are retrieved from large scale laboratory permeability and water retention tests and from in situ infiltration tests. The effect of WRP configurations on water flow into potentially reactive zones is examined with the numerical 3D fully-integrated surface/subsurface, variably saturated flow model HydroGeoSphere. Material properties retrieved from the laboratory tests are represented by means of stochastic facies distribution generated within a probability framework. Modelled soil water contents and hydraulic head distributions, as well as fluxes within a simple waste rock pile, with compacted layers, are compared with results retrieved from simulations based on the classical equivalent porous medium approach. Results indicate significantly increased flow towards the looser waste rock zone by considering heterogeneous material distribution, causing weak or absent capillary barriers and preferential flow paths. Practical implications for the design of waste rock piles are also discussed.

Aug 1, 2013

By H. Stocker, C. E. Makepeace

"This paper presents the statistical analyses of several sets of data acquired in several programs of sampling of radon daughters in uranium mines. The measurements were taken over periods of days or weeks for given locations or location occupations within these mines. Because the sampling applies to specific intervals of time and specific locations, a method is suggested f or the eventual application of a monitoring program which would be suitable on an annual basis for these locations. The present data and analyses thereof are not justifiably applicable to a monitoring regimen on an annualbasis, without a number of additional assumptions.The aim of the present analyses of concentration measurements is the determination of the minimum number of measurements required to achieve an annual radon daughter exposure estimate, for individual workers, having an error no greater than 50% at the 95% confidence level. The criterion of accuracy is taken from a statement in the American National Standard, Radiation Protection in Uranium Mines (ANSI NI3.8-I973), and is currently used, in somewhat modified form, as a guide to uranium mining licensees in Canada. Uncertainties associated with occupancy time are ignored in the present analysis. IntroductionOne of the principal aims of any scheme of radiation protection is that of improving the accuracy of exposure estimation for workers. The example presented here is from the area of radon daughter exposure estimation for uranium miners. The conventional means of estimating workers' exposures is grab sampling of radon daughter concentrations combined with occupancy time weighting in the various work and travel locations. Uncertainties exist in each of these components, and in an environment of highly variable radon daughter concentrations (such as an active uranium mine) one is always uncertain as to the representativeness of the grab sample (compared to the average concentration) unless a sophisticated monitoring scheme has been implemented based on previous experience in such an environment.Improvements in the accuracy and precision of employee radon daughter exposure records depend, primarily, on three factors;"

Jan 1, 1980

By Rafic Moubarac

FRP (Fiberglass Reinforced Polyester) equipment has been used in different and several applications during metals processing and extraction, and the hydrometallurgical process. Case histories of such equipment will be shown of major projects worldwide.

Jan 1, 2015

By J. Gray, J. Peck

As the turn of the century approaches, traditional open pit mining methodologies and processes are being modified through the introduction and use of new technologies. As in other industries, the personal computer is dramatically changing the traditionally conservative mining industry by allowing mines of varying size and capacity to increase their productivity and efficiency through the use of easy to use, office software. Computer-based monitoring and control systems are also being used more frequently to measure and optimize, in real-time, the performances of operating equipment. When communicated to an end-user, this information can provide accurate and timely answers to questions of how much, where, when, and by whom. This capability forms the foundation of a more comprehensive, proactive management and planning facility where, ultimately, information acquired from the producing equipment will be used to optimize and control machine and human activities. As these technologies mature and become essential tools in a mine, they will eventually serve as the basis for more robotic and autonomous mining operations.

Jan 1, 1999

By A. Torkian

Process water from production of concentrates in Meydook copper sulfide mine is transferred to the 8.3 million m3 tailings dam and a water retention pond after initial thickening. Elevated concentrations of heavy metals, sulfate, and TDS and decrease in pH as well as seepage into the aquifers have been the concern of the regulatory agencies since the start of activities. In this paper the results of a 6-month monitoring program from 4 wells are presented. The wells were located approximately 1.5 km from downstream of tailing dam (0.4 km from water retention pond) as well as upstream background well (2.28 km from water retention pond and 1.27 km from tailings dam). The objective was to study possible effect of accumulated tailings on the groundwater resources. Water levels in sampled wells were on average between 20 and 40 m. Results showed high levels of lead (5 ppb), copper (0.17-0.46 ppm) and selenium (73.1- 29.1 ppb). High levels of selenium and lead were partly due to natural geological settings of the area with high levels present in unaffected soils in the vicinity including water wells of villages upstream of mining operations. High copper levels were attributed to both mining operations as well as deposition from particulate air deposition onto the soil and transport to ground water by rain.

Aug 1, 2013

"THE GOLD MINING REGION of Timmins - Val d'Or, astride the Ontario-Quebec border, has long suffered the effects of rising costs during the period when the U.S. price of gold was fixed at $35 per ounce. The federal government, through such assistance programs as that set up under the Emergency Gold Mining Assistance Act (E.G.M.A. ) in 1948, has subsidized the gold mining communities of Canada for a total of over $300 million to March 31, 1972. Of this, the Timmins - Val d'Or ""gold belt"" has received more than twothirds, almost $220 million. In spite of these continuous subsidies, only 12 gold mines are still producing in the Timmins - Val d'Or belt, whereas 71 mines have received subsidies for some period since 1948. The vital question is how the communities previously supported principally by the mining of gold will survive in the long run, as many of the older mines either are already depleted or are quickly becoming so. With the rising price of gold on the 'free market in recent months, prospects look a little brighter for the time being. Even with the increased official price of U.S. $38, which made the maximum government subsidized price about $48 per ounce, gold mines have not sold any gold to the government since January 1972 and some stopped doing so months before that. The populace of the region has not been enthusiastic about relocation nor about extensive retraining programs in the past and probably will not be in the future. So, when the remaining gold mines become depleted, the old problems of community depression will remain."

Jan 1, 1973

By J. Fox, K. Kocsis

"Planning for sustainable cooling potential requires protected space to successfully maintain chilled propylene glycol in storage until needed. Stored propylene glycol should be judiciously cared for, safely kept from the ill effects of heat, in order to remain useful for bulk air cooling. Minimizing the chilled temperature of the propylene glycol reservoir tanks means that atmospheric conditions will be monitored closely during the chilling phase. Storage facilities would maintain restricted airflow while minimizing possibilities for heat transfer during the storage phase. Sustainable cooling systems could reduce or eliminate the need for mechanical cooling if installed with favorable conditions. Storing the cooling potential from the winter months is what this new design is all about.INTRODUCTIONIn most subsurface, bulk air-cooling methods, the main source of potential cooling energy comes from cold-water applications. This paper investigates the practical use of harvested, chilled propylene glycol as the source of cooling potential. Propylene glycol is chosen as the cooling storage liquid refrigerant since its chemical make-up is intrinsically safe to fresh water supplies and will not harm underground workers should a leak occur in the closed cooling circuit. Harvesting the cold of winter is a meaningless endeavor without proper thermal planning for the storage of the cooling potential in cold refrigerant.PROPYLENE GLYCOL STORAGE RESERVOIRA new design for a closed refrigerant bulk air cooling system employing propylene glycol as the refrigerant is presented as the main design topic of this paper. Given that a deep and hot mine will need to be considered safe and productive, a cost-effective cooling system is desired in order for the mining operation to be considered sustainable. For underground mines at northern latitudes, cooling applied to fresh air is only required 3 to 4 months of the year. During winter, ambient atmospheric conditions can be harnessed and stored for use at a later time.The basis of this sustainable design uses very cold ambient air that is circulated around galvanized steel refrigerant reservoir tanks. The propylene glycol reservoir tanks are arranged in a concrete walled pit, or tank farm, excavated in bedrock. During the coldest months, the tank farm will be exposed to the open air. As the seasons change the tank farm will be covered with insulation to maintain the maximum cooling potential for use during the warmest months of the year."

Jan 1, 2019

By K. E. Waters, N. Brodusch, R. Gauvin, H. Demers

"Rare earth elements are becoming increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. The characterization of the composition, morphology and volume fraction of the various phases that have valuable rare earths in the ores are needed to find the optimal industrial process to extract the ores containing the rare earths. Rare earth-bearing minerals contain many elements with the M-and L-lines overlap, requiring a high degree of resolution, pushing the boundaries of scanning electron microscopy quantitative analysis. Enhanced microscopy at a high spatial resolution with improved x-ray quantitative analysis enables the accurate determination of the distribution of the desired rare earths in various mineral phases. INTRODUCTIONRare earth elements are becoming increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. From batteries (lanthanum and cerium), to magnets (dysprosium and neodymium) and lighting (yttrium), the rare earth elements are crucial to the advancement of technology, and to energy saving devices (Crow, 2011). The goal of this project is to characterize the composition, morphology and volume fraction of the various phases that have valuable rare earths in the ores in order to estimate the economical VALUES (of the ores and to find the optimal industrial process to extract the ores containing the rare earths. High spatial resolution imaging and x-ray microanalysis are needed to reach this goal. In this work, the results obtained with a cold-field-emission scanning electron microscope (FE-SEM) and a silicon drift detector (SDD) energy dispersive spectrometry (EDS) detector at low accelerating voltage are compared to experimental conditions typically used with electron probe microanalysis (EPMA) instrument.With this improvement, a detailed scientific analysis of the composition of these, and other, ores will become possible with a SEM/EDS system. This will help to better understand how such ores were formed, hence assisting in finding them, and to better understand how to process them in preparation for high end industrial applications, namely through mineral processing."

Jan 1, 2012

By R. L. Christie

"THE ISLANDS lying north of the Canadian mainland, and the large Boothia and Melville peninsulas, form one of the great archipelagos of the world; this sparsely vegetated and nearly unpeopled region extends about 1,500 miles east to west and 1,200 miles from the mainland to the northern tip of the northern-most island. Sea access to most of the islands is restricted by ice to the summer season, and the 'polar pack' ice of the Arctic Ocean presses the year round against the northwest margin of the archipelago. Although the region is remote, the accessibility has greatly increased through a network of weather stations, airfields and air routes connecting with southern centres.The area considered in this paper is that part of the island region underlain mainly by sedimentary rocks. In broad terms, this includes the land and sea areas of the archipelago and the adjacent continental shelf, but excludes the dominantly 'Shield' terrain of Baffin Island, and of Melville and Boothia peninsulas. An impression of the size and potential of this sedimentary region may be gained by comparing some areas: the land area of islands underlain mainly by sedimentary rocks is over 300,000 square miles or about 50,000 square miles greater than the area of Alberta. The total area of the region, including the continental shelf and the inter-island areas, may be double this figure, and may approximate one-seventh of the land area of Canada."

Jan 1, 1970

By Samuel O. Akande

"Gold occurs as native metal, in electrum, and in a telluride mineral in quartz carbonate veinlets of three vein systems at the Ross Mine, northern Ontario. The 14 Vein System is made up predominantly of concordant veinlets within layered ankeritic dolomite stratabound by, and conformable with, andesite tuff Individual veinlets contain pyrite, sphalerite, galena, chalcopyrite, tennantite, pearceite, proustite, native gold and electrum in a matrix of quartz, dolomite, ankerite and calcite. The 2B Vein System is made up of both concordant and discordant veinlets within andesite tuffs. The veinlets contain pyrite, chalcopyrite, sphalerite, bornite, tennantite and free gold in quartz, calcite and dolomite. The 18 Vein System is comprised of stockwork veinlets in and around intrusive syenite which has both sharp and gradational contacts with enclosing andesite tuff The veinlets contain pyrite, chalcopyrite, bornite, chalcocite, native gold and calaverite. Sulphide and silicate minerals in veinlets and wall rocks are stable assemblages for the regional metamorphism of greenschist rank. ,The 14 Vein System is interpreted as a metalliferous siliceous carbonate chemical sediment, the components of which were leached from the underlying volcanic rocks by convecting sea water and subsequently deposited on the sea floor between the extrusion of flows and pyroclastic rocks. Subsequent regional metamorphism and intrusions remobilized and redistributed the syngenetic stratabound material into dilatant fractures in adjacent tuff, as in the 2B and the 18 vein systems."

Jan 1, 1982

By W. F. J. Cosser

AN agreement having been arrived at in 1935 whereby McIntyre Porcupine Mines would purchase gravel for back-filling purposes from Hollinger Consolidated Gold Mines, the aerial gear as described below was installed. As originally discussed, the plan called for installation of a loading bin at the junction to the Hollinger tram, so making the McIntyre tram an entirely separate unit. The experience of the Hollinger engineers, however, went to prove that the operation of a bin (remote from sources of heat) should be avoided if possible, owing to the severe winter conditions (35° to 40° F. below zero).

Jan 1, 1938

By J. W. McCammon

CRANGES in construction ideas and the continually rising costs of labour and conventional building materials, particularly since World War II, have prompted widespread investigations into the development and adaptation of new materials to meet the new requirements and to help reduce costs. Lightweight aggregates have been prominent in these investigations. The lightweight aggregates most commonly used today are foamed slag, cinders, pumice, diatomite, exfoliated vermiculite, expanded perlite, and bloated clay or shah. Lightweight aggregates contribute to the building industry in several ways: ( 1) in large structures the reduction in deadweight effected by the use of lightweight materials reduces the amount of reinforcing and structural steel necessary to support the structure; ( 2) the decrease in weight of lightweight blocks makes handling easier and faster; (3) pre-fabricated floor and roof slabs and tilt-up walls of lightweight concrete have become feasible and popular; ( 4) lightweight aggregate concrete has good nailability and is easily channelled; (5) concrete and plaster made with lightweight aggregate have good heat and sound insulation properties.

Jan 1, 1957

By F. Mackay, S. A. B. da Fontoura

"The theoretical solution for a viscoelastic well was presented by Gnirk and Johnson in 1964. From this an exercise was executed to validate the numerical simulation of a cemented salt well. The exercise comprised the geomechanical behavior through time of a cemented salt well, this was achieved using a finite element commercial software. This simulation showed the accuracy of the theoretical solution for viscoelastic materials such as salt rock. The theoretical solution presented elastic and viscoelastic analytic equations for the tangential and radial stresses. The equations for the elastic material (casing and cement) and for the viscoelastic material (salt rock) are presented here: Where equations 1a & 1b are the radial and tangential stresses of the elastic material; equations 2a & 2b are the radial and tangential stresses of the viscoelastic material; and a, r and b are the geometrical parameters explained in Figure 1. These equations are function of Pb, a stress time dependent factor that comes from the Burgers model of viscoelasticity. This is well explained in Gnirk and Johnson (1964) and for the sake of simplicity is not disclosed here. Po is the stress at section A-A’ dependent of the depth h."

Jan 1, 2015

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By N. W. Xu, C. Sha, F. Dai, Y. G. Zhu, B. Li

Underground caverns stability and excavatability of rock masses are of significance in geotechnical engineering, in both design and construction stages. Risks associated with underground group caverns of Houziyan hydropower station in southwestern China are growing as a result of continuous excavation-induced unloading. To improve our understanding of the underground caverns instability and resolve the complex subsurface conditions of the highly fractured rock mass, a high resolution microseismic monitoring system was established in the deep underground caverns, pursuing the relationship between the measured data about microseismic activity and excavation damage zones of surrounding rock mass. Through analyzing the tempo-spatial distribution of microseismic activity, excavation damage zones and potential risk regions in underground caverns were identified. Furthermore, the correlation between microseismic activity and pre-existing geological structures, as well as traditional monitoring was analyzed. In order to validate the correlation between seismicity and potential slip surface of underground caverns, a model was implemented into numerical code to further evaluate the deformation and stability of surrounding rock mass. The monitoring results demonstrate that microseismic events mainly occur at high stress concentration regions, which coincides with the results obtained from numerical analysis. Therefore, the comprehensive method incorporating microseismic monitoring and numerical analysis, as well as traditional monitoring and filed observation has been proven to be very promising in deformation and even instability prediction of surrounding rock mass in underground caverns subject to delineation of potential slip surfaces and excavation damage zones.

Jan 1, 2015

By M. Fairclough, B. Moldovan

Insights into uranium mining projects of the future can be gained by a careful statistical analysis of past and present deposits, as well as an examination of recent trends for uranium resource evaluation and primary uranium production. The International Atomic Energy Agency (IAEA) provides the necessary data and corresponding mechanisms as inputs for methodologies that enable strategic and scientific evaluations of long-term security of supply uranium required to sustain the demand for nuclear fuel. Sustainability of the uranium mining industry and subsequently new uranium mines of the future requires innovation and expertise to lower operating costs, maintain or improve uranium recovery while meeting the requirements of stakeholders in regard to protection of the environment and safety of the workers and general public.

Jan 1, 2020