Search Documents

By D. Lauzon, H. de Ruiter

"In 1988a decision was taken to design and install a computerized mine monitoring and control system. This system had to monitor and control all pumping and ventilation underground. The operation of the mine air heating, using waste heat from the mine water and compressors, was to be part of the system. It ultimately also had to interface with the four existing Canadian General Electric Series 3 PLC's which controlled the No .3 shaft loading pockets. Beside operational control and trouble shooting, the system is a valuable tool in energy management and ultimate savings are estimated at $50,000 per year.The final equipment selection was a General Electric Series Six PLC on surface with a total of 17 Series One Plus and Juniors PLC located underground. Data is transferred through a two-pair shielded cable using modems. Both analog and digital functions are being utilized.The basic monitoring and control system was commissioned during 1989and, due to a higher level of technology today, further improvements have been planned for the future. The system was designed by Walter Dow together with Gordon Champion of D.G. Champion Engineering Ltd. of Toronto. Advice for the ventilation part of the project was obtained from Maurice White, Independent Ventilation Consultant.The Ministry of Energy, Mines and Resources and the Ministry of Energy of Ontario approved this project together with the waste heat recovery project to qualify for a grant of$135,000 under the Enerdemo-Canada program.IntroductionThe Macassa mine is a narrow vein gold mine situated about 2 km west of the town of Kirkland Lake in northeast Ontario. The mine has been in continuous operation since 1933 and a total of about 3.0 million ounces have been recovered out of 6.6 million tons of ore ."

Jan 1, 1991

By B. Huffman

This paper examines several new trends in the design and application of linings for copper melting shaft furnaces including the use of large shapes, monolithic back-up linings and improved refractory engineering to significantly reduce refractory installation time, diamond saw blade costs, fuel and down-time. The net results are shown to be dramatically increased refractory service life, reusable safety linings, elimination of hot spots and lower refractory disposal costs.

Jan 1, 2007

By Norman Lecuyer, Jacque Nantel

"The Chadbourne Project, located within the limits of the town of Noranda, Quebec, will make use of backfill materials to fill the voids left by the mining of stopes and pillars. A series of tests were conducted on different mixtures of slag and pyrrhotite tailings materials to evaluate their properties. The tests are described and some pertinent results are given in the paper.IntroductionThe Chadbourne Project is located in the centre of the Town of Noranda, Quebec, with houses as close as 120 m from the blasting operations. The ore is mined using the vertical crater retreat method. The voids left by mining activities will be filled. A program of pillar recovery will follow.Considering the proximity of houses and the need to recover pillars, the backfill program must be carefully laid out. No subsidence can be tolerated on surface.With these objectives in mind, a test program was undertaken by Nantar Engineering Limited and Queen's University to evaluate the possible ba ckfilling alternatives available to Chadbourne. One of the possibilities retained was the use of a backfill composed of broken slag material from the Horne Smelter and pyrrhotite tailings deposited on the Horne's pond a number of years previously.The back fill used at the Horne Mine until the mine closed in 1975 was composed of a mixture of 97% granulated slag and 3% pyrrhotite tailings. The tests leading to its use underground at the Horne Mine were described by Patton in 1952. The structural properties of the Horne backfill were ""intuitively"" known; it was agreed by all at the Horne Mine that the backfill was behaving remarkably well. Some were labeling it ""the best backfilling material in the world"". Its strength was said to be that of a weak concrete. All of the preceding indicate that the Horne backfill had never had its structural and other properties determined in the laboratory."

Jan 1, 1983

By F. Rosenblum, P. Spira

"A correlation has been established between the oxygen demand of Brunswick Mining and Smelting ore and flotation results at the bench, pilot plant and operating plant scale. A method of dete""1llining the aeration requirement of sulphide ores on the basis of this correlation is presented. It is shown that abraded iron from grinding media plays an important role in aeration and flotation. Laboratory grinding must therefore be conducted under controlled conditions with suitable grinding media in order to obtain the true aeration requirement of the ore.A method of evaluating aerator efficiency, also based on oxygen demand measurements, has been used successfully at Brunswick Mining to design pilot plant and full-scale aeration systems.1. IntroductionPre-flotation aeration of sulphide pulps has been practiced in the Noranda Group for many years to help in the depression of pyrite and pyrrhotite and to promote chalcopyrite and/or galena. Recently, two out of three parallel circuits at the Brunswick Mining and Smelting Corp. Ltd. concentrator have been converted on a test basis to a new flowsheet incorporating aeration as a basic step. Among other benefits, a substantial decrease in the middlings load has been achieved as a result of improved pyrite rejection. There has been increasing interest in other organizations in the potential advantages to be derived from' aeration in terms of improved metallurgy and/or decreased reagent consumption."

Jan 1, 1978

By Sergio Romo, Gerardo Fuentes, Adriana Garcés

Refractory ores with gold entrapped in a sulfide matrix, must be processed in a first stage with chemical or physical treatment in order to liberate the gold for a subsequent step with cyanide. The goal of this research was to compare the refractory behavior of a gold concentrate treated using two pretreatment methods: pressure oxidation and fine grinding. Gold concentrate from Viacha Mining in Bolivia, assaying 50.11 gpt, with a P80 of 131 ?m was used. The concentrate contains arsenopyrite and pyrite as main sulphides in the matrix. A preliminary test with cyanide resulted only 13.5% of gold extraction with 4 hours of stirred leaching. Using an autoclave oxidation with sulphuric acid and 12 bar oxygen pressure at 220°C pretreatment, the cyanide gold extraction increased to 69.0% in 4 hours. When material was ground in a pulverizer, producing a P80 of 20 ?m and the product directly cyanided, stirred leaching gave a gold extraction of 65% in 4 hours. For both techniques, the effect of temperature, sulfur produced in autoclave oxidation, optimization of the cyanide and the nature of residues were also studied.

Jan 1, 2014

By H. Lee

Recently, the effects of global climate changes have become top concerns for governments? decision making regarding infrastructure investments. Extreme weather events that exceed the capacity of existing systems have considerably increased in frequency, and the potential effects of changing trends in temperature and rainfall on infrastructure are difficult to ignore. It is essential for governments to estimate the costs and benefits of adaptation to climate change to properly assess the financial feasibility of infrastructure adaptation strategies. This paper proposes a framework for estimating the economic aspects of infrastructure adaptation to climate change. The framework is composed of three steps of implementation: establishment of alternatives for infrastructure adaptation, performance prediction of infrastructure using future climate scenarios, and asset valuation based on costs and benefits. The first step specifies target assets, their adaptability to climate change, and applicable adaptation technologies. The second step evaluates the effects of climate change on the performance of infrastructure. The last step determines the optimal adaptation strategies among various alternatives based on their net benefits. The framework reasonably incorporates future climate scenarios into the estimation processes for climate change effects and provides a basis for budget allocation for governmental infrastructure investments. The framework is expected to assist government decision makers in establishing adaptation strategies in a rational manner under uncertain future climate change.

Aug 1, 2013

By J. Stachulak, M. Scobie

"This paper addresses the occurrence and indicated causes of conveyor fires in North American and European underground mines. Some significant convey or fires which have been experienced in recent years in Canadian hardrock mines are then reviewed. The nature of existing conveyor monitoring technology is considered in the context of such fire hazards. Experiences with new monitoring technology recently installed at several conveyor sites at Inca Ltd. mines are then reviewed.IntroductionFires associated with conveyors have long been recognized as a serious hazard in underground coal mines. Recently, however, there have been some significant conveyor fires in Canadian underground hardrock mines. These offer important evidence as to the nature and causes of potential hardrock mine fifes. They also warrant attention with a view to improving over-all mine design, ventilation and emergency preparedness.In addition, a new era in mine communications and monitoring technology has been entered which should offer improved capability to protect against such fires. This paper was motivated by the need to understand the causes and mechanisms of conveyor fires in order to improve their safety. This should be possible through implementing more effective monitoring systems, as well as improving conveyor design. Underground mines are becoming more intensively mechanized, with less human surveillance of equipment and a greater dependency on remote monitoring systems."

Jan 1, 1992

By T. Macpherson

Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By T. Kawai

Japan Oil, Gas and Metals National Corporation (JOGMEC) has started an exploration program for Seafloor Massive Sulfides (SMS) in the EEZ of Japan, and launched an investigation program for mining, processing and environmental impact on SMS development. With regard to the mining aspect, the mining system consists of three units: a mining unit on the sea floor, an ore lift-up unit to surface, and a mining support vessel unit which has an ore unloading system that unloads onto a shuttle ship. Regarding the mining unit, JOGMEC and certain Japanese mining and machinery companies developed two types of state of the art mining testing tools. Excavation tests on the actual SMS site in the Okinawa Trough, south-west of Japan, were conducted in 2012. In these tests, the functions of the testing tools, such as cutting ore, moving on the seafloor and climbing up slopes having steeper than a 25 degree gradient, were confirmed. The physical characteristics of the ore, which are key parameters for establishing a mining system, are yet to be fully understood as the exploration program has been undertaken simultaneously. Hence, those examinations have been carried out by ground cutting experiments, analysis of drilling core data, and the like. This paper describes the outline of a proposed mining system, mining testing tools and results of the on-site mining testing.

Aug 1, 2013

By N. Moelans, I. Bellemans, K. Verbeken

In this work, we present a phase field model to simulate the facetted crystallization of Fe3O4 in a quaternary FeO-Fe2O3-Cu2O-SiO2 melt under different partial pressures of oxygen. An important focus in creating more realistic phase field models is the incorporation of the thermodynamic driving forces in multicomponent multiphase-field models by coupling to thermodynamic databases. The diffusion of FeO, Fe2O3 and Cu2O is considered. The ratio of FeO/Fe2O3 at the upper boundary is in equilibrium with the oxygen fugacity of the atmosphere, while conserving Fe. Two-dimensional simulations are performed with different varying oxygen fugacity in the atmosphere. For the considered composition range, the growth velocities of the spinel crystals increase with decreasing oxygen fugacity. INTRODUCTION Crystallization of silicate melts has its applications in geology, pyrometallurgy and glass making. In pyrometallurgy, the solidification of slags influences the freeze lining behaviour (Campforts et al., 2007) and the cooling of slag after tapping (Durinck, Jones, Blanpain, & Wollants, 2008). Modeling of silicate melt crystallization is frequently done on the macroscopic level, using thermodynamic equilibrium calculations to determine the fractions of all phases as a function of temperature. The Factsage software and database package (Bale et al., 2016, 2009, 2002) already proved its usefulness in pyrometallurgical applications, for example to model the phase mixture after solidification of a stainless steel slag (Durinck et al., 2008). Crystallization of phases typically results in complex morphologies on the mesoscale, e.g. dendrites or facetted growth. On this mesoscale, the phase field concept has proved to be a very powerful tool (Moelans, Blanpain, & Wollants, 2008) for modeling crystallizing microstructures, because it can treat arbitrarily complex interface shapes with minimal mathematical complexity. In contrast to macroscopic models, the diffusion profiles and crystallization kinetics can be described as well as the morphology of individual crystals. First, Kobayashi (Kobayashi, 1993) simulated a growing dendrite in a pure undercooled metallic liquid. Then, Warren and Boettinger (1995) simulated a dendrite in an isothermal system considering a binary alloy. The extension to multi-phase systems was done by Steinbach et al. (1996). This was further extended by Tiaden, Nestler, Diepers, and Steinbach (1998) to a framework with coupled diffusion and phase field equations in multi-component systems.

Jan 1, 2019

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By Z. Zhao, B. Li

"Fractures are the key channels for fluid flow and mass transport in fractured rocks of low/negligible matrix permeability. In single rock fractures, surface roughness causes fluid flow in tortuous paths, and reduces the overall fracture conductance. A number of empirical models have been proposed to relate the reduced hydraulic aperture to the mechanical aperture due to surface roughness, which were revisited and compared. Using two of those relationships between hydraulic apertures and mechanical apertures, we studied the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks. The results show that fracture roughness can affect the flow rates and residence time to varying extent, mainly depending on the empirical models between hydraulic apertures and mechanical apertures. However, fracture roughness has negligible influences on the general patterns of fluid flow (channeling) and solute migration (e.g., travel paths and shape of breakthrough curves). This is because the connectivity of a fracture network is mainly determined by other geometrical parameters (fracture positions, orientations, and lengths), rather than roughness or apertures. INTRODUCTIONIn fractured crystalline rocks of low or negligible matrix permeability, fluid flow and contaminant migration mainly occur within the connected fractures. An understanding of fluid flow and contaminant migration in fractured rocks is a crucial issue in many deep underground projects, e.g. underground repositories for radioactive waste, CO2 sequestration, enhanced geothermal systems, oil and gas production, etc. Rock fractures are typically rough-walled, and surface roughness appears to have first order control on the mechanical and hydraulic behavior of single rock fractures (Boutt et al., 2006).It is well known that the mechanical aperture of a rock fracture is usually larger than its hydraulic aperture, due to fracture surface roughness (Tsang and Witherspoon, 1983). However, for naturally fractured rocks including numerous discontinuities, the effects of this reduced hydraulic aperture in local fractures on macroscopic fluid flow and solute transport in complex fracture systems still remain unclear. Many previous studies assumed identical hydraulic and mechanical apertures in discrete fracture network models for simplicity (Min et al., 2004; Zhao et al., 2011). Therefore, the main objective of this study is to evaluate the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks, by employing the empirical models that relate the hydraulic aperture to the mechanical aperture."

Jan 1, 2015

By Maria Agostina Cinellu

Some aspects of the reactivity of the two different kinds of gold(III) oxo complexes [Au2(N,N)2(?-O)2][X]2 [N,N = 2,2'-bipyridine (bipy) (1), 6-alkyl-2,2'-bipyridine (bipyR) (2), R = Me a, CH2Me b, CHMe2 c, CMe3 d, CH2CMe3 e] and [Au2(C,N,N)2(?-O)][X]2 [HC,N,N = 6-benzyl-2,2'-bipyridine (bipyR') (3), R' = CHMeC6H5 a, CMe2C6H5 b] (X = BF4, PF6) have been studied. Treatment with water converts the unsubstituted bipyridine complex [Au2(bipy)2(?-O)2][PF6]2 (1) and the cyclometallated derivatives [Au2(C,N,N)2(?-O)][PF6]2 (3) into the water soluble monomeric hydroxo species [Au(bipy)(OH)2][PF6] (4) and [Au(C,N,N)(OH)][PF6] (5), respectively. These hydroxo species, likely the intermediates in the formation of the oxo complexes, are quantitatively reverted to the latter ones by reflux in anhydrous solvents. Both kinds of oxo complexes react with PPh3 to give OPPh3, the gold(I) complex [Au(PPh3)2][PF6] and the free bipyridine ligands. The reaction of the dioxo complexes [Au2(bipyR)2(?-O)2][PF6]2 (2a, 2b, 2c, 2e) with different alkenes gives the unprecedented alkene complexes [Au(bipyR)(?2-alkene)][PF6]. The styrene adduct [Au(bipyip)(?2- CH2=CHPh)][PF6] (7) (bipyip = 6-iso-propyl-2,2?-bipyridine c) has been characterized, inter alia, by X-ray diffraction analysis. Organic products arising from olefin oxidation are also found in the reaction mixture.

Oct 1, 2003

By R. Tessier, R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. The paper presents findings in the on-going testing of various sizes and shapes of grinding media. Breakage rates are used as an aid to assess the effect of grinding media. Results of empirical and phenomenological analyses demonstrate the importance of adequate selection of media sizes on the milling operation.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mine near Bathurst, New-Brunswick. The No. 12 ore body is an extremely fine grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite. The operation is currently processing 10,500 tonnes of ore per day in conventional crushing, grinding, differential flotation and dewatering circuits. Details on the circuit can be found elsewhere (e.g. Hendriks and Ounpuu, 1985; Grant et al., 1991).The mill has operated for more than 25 years and despite the past milling experience, there has been much disagreement as to the required grind size. Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37µm) and averaged slightly over 71%in1992. Results from mineralogical analysis (Petruk and Schnarr,1981; Coleman, 1988), Brunswick metallurgical laboratory (Grant et al., 1991; Shannon et al., 1992) and Lakefield pilot plant tests (Hendriks, 1984; Hendriks and Ounpuu, 1985) clearly indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15-25µm range."

Jan 1, 1993

By A. Welty, T. Garn, K. Lyon, B. Jakovljevic, R. S. Herbst, M. Greenhalgh, Cytec Solvay Group

"Industrial rare earth separation processes utilize PC88A, a phosphonic acid ligand, for solvent extraction separations. The separation factors of the individual rare earths, the equipment requirements, and chemical usage for these flowsheets are well characterized. Alternative ligands such as Cyanex® 572 and the associated flowsheets are being investigated at the pilot scale level to determine if significant enhancements to the current separation processes can be realized. These enhancements could be defined as higher separation factors, reduced stage requirements, or reduced chemical consumption. Any of these enhancements can significantly affect the costs associated with these challenging separation proccesses.A mid/heavy rare earth element (REE) separations flowsheet was developed and tested for each ligand in a 30 stage mixer-settler circuit to compare the separation performance of PC88A and Cyanex® 572. The ligand-metal complex strength of Cyanex® 572 provides efficient extraction of REE while significantly reducing the strip acid requirements. Reductions in chemical consumption have a significant impact on process economics for REE separations. Partitioning results summarized Table 1 indicate that Cyanex® 572 offers the same separation performance as PC88A while reducing acid consumption by 30% in the strip section for the mid/heavy REE separation."

Jan 1, 2016

By M. Tadie, J. Wiese, K. Corin

The use of potential control in the flotation of ores has been applied in a variety of operations and presents an opportunity for improvement of selectivity and recovery of valuable minerals. Although it is possible to vary the redox potential (Eh) using chemical additives such as sodium hypochlorite or hydrogen peroxide this is more commonly done by varying the pH and dissolved oxygen (DO) concentration. The present study involves an investigation into the effect of varying dissolved oxygen concentration, ionic strength (IS) and pH on the flotation response with the aim of application to a South African lead-zinc ore. In all cases the Eh is measured as a function of the different DO, IS and pH values. The main objective was to achieve selective flotation of galena from sphalerite. The first part of the work was micro-flotation tests conducted on single minerals with galena used as the basis for effect of the factors studied on redox potential and ultimately recovery. The DO was varied by alternating between the use of air and nitrogen as the gas source to the micro-flotation cell. PH was varied between pH 9.2 and pH 11.8 using sodium hydroxide. In the first part of this study a factorial design approach was used to determine the interactive effects of the variables tested, viz. DO, ionic strength and pH, on the Eh and on the recovery. Redox potential was measured using a combination electrode made up of platinum wire and Ag/AgCl reference combination. Recoveries indicated that pH had the most significant effect on recovery and Eh. The influence of redox potential on recovery was found to be of relevance to the condition of high dissolved oxygen concentration and less so at low dissolved oxygen concentrations. It was also noted that that the combined interaction between ionic strength and dissolved oxygen concentration had a positive effect on recoveries, however this was not so with Eh. The chemistry of the ions in solution was observed to play a dominant role on the recovery due to changes in solubility arising to pH modification. The longer term objective of this work is to determine the optimal Eh conditions for the separation of galena from sphalerite.

Jan 1, 2016

By Harvey McLeod

M3 -Technology HOWEVER:In practice we have limitations ?Clients: aggressive or cost based; inexperienced ?Consultants: ?expanding market w/training limitations ?Prescriptive designs ?Lack of senior oversight ?Regulators: difficult to retain technical capacity ?Stakeholders: perceptions and expectations ?Physical settings: challenging terrain, climate, soils/rock Do M3?s Perform? YES?Generally M3?s since mid-1960 do perform ?BC Closed Mines: Afton, Highmont, Trojan, Bethlehem, Cheni, SNIP, NO?ARD/ML issues?e.g. Equity Silver, Samatosum; selenium, cadmium, sulphate

May 1, 2010

By B. Das

"Computers have been used extensively in the mineral industry in exploration, reserves calculation, mining technology, mineral processing, etc. With respect to coal mining, there are also various applications for evaluating rock slope stability of open pits, design of open pits, underground operations, mine ventilation, ground control, data processing and management information, operations control and certain technological applications. Mine ventilation appears to be the field in underground coal mining touched on most; on the other hand, underground coal mining methods evaluation is represented only sparingly.It is therefore essential to review the status of the computer in underground coal mining methods evaluation in order to define its scope for further application. The paper discusses the roles of the mining engineer, programmer, computer operator and analyst as well as that of the computer. The important parameters will be identified and discussed along with their application for different underground coal mining methods, with their individual unit processes. Mainly, longwall face operations have been covered. Although many models have been of academic interest, they can be considered as important steps in a transition stage which will be followed by more practical applications for computers for underground coal mining method evaluations in the future. This calls for a coordinated effort from all concerned."

Jan 1, 1981

By R. G. Eggert

"A critical element, as the term has come to be used, provides essential properties to a modern engineered material and is subject to supply risk. The rare-earth elements became perhaps the most prominent of the critical elements in recent years because of their important uses in permanent magnets, advanced lighting, and military materials; the geographic concentration of production in China; and the dramatic run-up in prices in 2010-2011 followed by price collapse between 2011 and 2016. Yet criticality extends beyond the rare earths. What is critical depends on your perspective – who and where you are, and when you ask. This paper reviews the many perspectives on, or faces of, critical elements. It compares and contrasts perspectives of industry (General Electric), national or regional manufacturing sectors (Japan, European Union), emerging energy technologies (as seen by U.S. Department of Energy and, separately, Joint Research Centre of the European Commission) and the world as a whole (as evaluated by academics). This comparison reveals a diversity of not only perspectives but also methodologies and time frames of concern.INTRODUCTIONRare-earth elements appeared prominently in the news in 2010 and 2011 because of the dramatic increase in their prices; their important uses in permanent magnets, advanced lighting, and military materials combined with the geographic concentration of production in China, which reduced export quotas significantly. Rare earths became the most prominent of what have become known as critical elements or materials – that is, those that provide essential properties to modern engineered materials and yet are subject to supply risks.Yet criticality, the state of being both essential and subject to supply risks, extends beyond rare earths. What is critical depends on your perspective. This paper begins by reviewing a little history and presenting a general conceptual framework from which to think about critical materials. It then reviews the many perspectives on, or faces of, critical elements – corporate, national, and global, as well several that focus on emerging energy technologies. The paper concludes with thoughts on what to do to mitigate the potentially negative effects of the supply risks associated with criticality."

Jan 1, 2016

By Bhawani Singh, Mahendra Singh, N. K. C Samadhiya

"Inherently anisotropic rocks occur in abundance at many rock engineering project sites in Himalayan region. These rocks pose difficulty in analysis and design due to their direction dependent strength behaviour. Moreover the strength varies in a non-linear manner with confining pressure. Mohr- Coulomb strength criterion is widely used by geotechnical engineers for defining strength of rocks subjected to given confining pressure. However, the conventional Mohr-Coulomb (MC) criterion suffers from the limitation that the strength is treated to be linearly dependent on confining pressure. In the present article, the MC criterion has been modified by incorporating non-linear term while retaining the original parameters c and ?. The non-linearity with confining stress level has been imbibed through critical state concept (Barton, 1976). The criterion has been applied to a triaxial test data base comprising of more than 1140 triaxial tests conducted world-wide on anisotropic rocks. Statistical evaluation of the goodness of fit of the proposed criterion to the data-base has been carried out. Further the predictive capabilities have been evaluated by determining the error in estimation of triaxial strength if only few triaxial test data are available for determining the criterion parameters. The data base has also been back-analysed to assess the critical confining pressure for anisotropic rocks. Statistically the critical confining pressure, for the present criterion, may be taken nearly equal to 1.25?cmax, where ?cmax is the maximum value of the UCS out of all orientations of planes of anisotropy. It is concluded that reasonably good estimates of the anisotropic strength are possible through the proposed criterion.INTRODUCTIONMany rocks encountered in Himalayan region like shale, slate, schist and phyllite are inherently anisotropic and exhibit direction dependency in their strength behaviour. In addition, the strength of the rock also depends on the confining pressure and, the strength response is non-linear especially when the confining pressure may vary over large range. Conventionally, Mohr-Coulomb criterion is the most widely used criterion for rocks. However, the limitation of this criterion in its present form is that the strength is treated to be linearly dependent on the confining pressure. The present study attempts to address the following two main objectives: i) Include nonlinear response in the Mohr-Coulomb criterion while retaining parameters c and In their original form; and ii) consider anisotropic response of the rock for a given confining pressure. A nonlinear strength criterion, which uses shear strength parameters c and as per Mohr-Coulomb criterion, has been suggested based on critical state concept for rocks."

Jan 1, 2015