Search Documents

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By Dale S. Preece, Ruilin Yang

Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidly attenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that the resulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of the explosive. The induced air blast reflects from the bottom of the borehole and this reflected pressure, even though doubled, is still approximately two orders of magnitude less than the detonation pressure. Air-shocks will ring back and forth in the air-deck for a few tens of milliseconds while the adjacent explosive column(s) are detonating. Transmission of the initial shock through the air along with reflections is an intensive energy consuming process. Energy balance results in shock heating of the air and a temperature increase. However, the increased temperature of the air is also orders of magnitude less than that of the explosive detonation products immediately behind the detonation front. Replacing high energy explosives with zero energy air-decks in a blasthole will always have a negative impact on the adjacent rock fragmentation and movement.

Jan 1, 2016

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

Active avalanche control is the intentional triggering of avalanches while people are kept out of the hazard area. Explosives are frequently the most effective tool for triggering avalances. In a highway setting an avalanche control program will reduce total highway closure time, while providing greater safety to motorists and maintenance personnel. Avalanche control with explosives is effective when the snow is somewhat unstable and almost ready to slide naturally. Forecasting this condition involves having a network of local meteorological stations, examining snow structure, using mountain weather forecasts, doing snow strength tests, and having the results of ski and explosive tests. The method of delivery of explosives to an avalanche starting zone is governed by the accessibility of the starting zone. Common methods include; hand placing or throwing charges, remote delivery cableways, or "trams", surplus military weapons, and a compressed gas charge launcher, or "Avalauncher". Charges dropped from helicopters are also occasionally use. We have increased the effectiveness of our program by use of large elevated charges. Efforts are being made around the world to develop and utilize better methods for the safe, remote initiation, but procedures have varied dramatically between individual control programs. There is now a movement to review and standardize operational guidelines for avalanche control. Highway avalanche control is often done at night, during winter mountain storms. Heavy rain or snow, high winds, and high avalanche hazard, are common work site conditions. Commercial and economic pressures are increading, so methods that redice highway closure time are important. There are also many safety issues to be addressed in avalanche control work.

Jan 1, 2002

By Mark Fritzen

Drilling and blasting near residential or business inhabited areas may expose people to blast induced vibration. Many of these people have never been exposed to blast vibration and airblast which can cause a variety of reactions ranging from indifference to anger. Blasting contractors seeking to minimize the impact of blasting to neighbors of the project will plan for a public relation plan which begins at bid time. The public relations plan cost will be included in their proposal and a variety of methods may be included including, door to door contact, letters, pamphlets, telephone calls, and the use of an independent consultant to conduct a pre-blast survey. By raising the awareness of neighbors to a blasting project the blasting contractor may reduce the anxiety and stress of unannounced blasting vibration and airblast. This helps everyone associated with the project from the project owner(s) to the blasting contractor.

Jan 1, 2000

By Carlos Enrique Arroyo Ortiz, Jadir Pedro Alves

This paper presents some of the results obtained during the research work about the use of technologies and digital transformation in the process of rock drilling in open pit mines. The use of automation presents itself as a disruptive factor and a driver of improvements that provide sustainability in rock drilling. Seven main operational parameters were utilized to combine measurement while the drilling (MWD) with other information generated by the equipment during hole drilling, in six different lithologies in an iron mine, located in the central region of Minas Gerais in Brazil. Adjustments and corrections were made to the data collected in order to minimize external influences other than the rock itself, to ensure the effectiveness of the analyses. Finally, we sought to compare the performance of the drilling process in manual and automatic operation modes. Thus, making it possible to show the efficiency and impact on the sustainability of rock drilling operations in open pit mines.

Feb 6, 2023

By Keith Maki

This paper details a simple substitution of precise electronic timing in the holes for standard pyrotechnic delays. In addition, we wanted to use two electronics in bottom and top to test the colliding shock wave theory. It also discusses the difficult loading conditions on the Iron Range of Northern Minnesota. No preliminary analysis (Signature Hole waveform analysis) was done to determine the most favorable blast timing for fragmentation increase or vibration reduction.

Jan 1, 2007

By Randy Wheeler

In recent years the issue of seismograph calibration and accuracy has been a major focal point of the ISEE Blast Vibration and Seismograph Section. In fact, questions concerning the consistency and reliability of seismograph measurements essentially led to the development of this ISEE section. One of the early actions of the section involved the development of “Field Practice Guidelines” for the use of seismographs. These guidelines specifically state that “Placement and coupling of the vibration sensor are the two most important factors to ensure accurate ground vibration recordings.” This paper will address the results obtained from using different coupling methods to record vibration and airblast levels generated from production blasting in a limestone quarry. The data obtained clearly indicate that seismometer burial provides the best coupling for recording ground vibrations. Microphone height has also been an issue regarding the accuracy of recorded airblast levels. The data we obtained indicates that microphone height is not a significant factor.

Jan 1, 2004

By Clara Godoy, Álvaro Dapía, Paulo Couceiro, Håkan Schunnesson, Juan Navarro

This paper applies geostatistical tools in Measure While Drilling (MWD)data to estimate the probability distribution of values in all the points of the studied domain in order to assess the continuity of rock classes between boreholes. The analyses carried out by Ghosh et al.(2018) and Navarro et al.(2019) have been used as starting point of this work to classify the geotechnical rock condition in four classes: solid rock, fractured rock, cave-in rock and cavity. From it, an application for the geotechnical rock condition of ore bodies have been developed, aiming at characterizing the rock before the charging the holes to minimize unexpected rock conditions and to address issues associated with charging and blasting operations. Such problems are closely related with non-optimal rock fragmentation after blasting. The procedure has been applied in the geotechnical block model results obtained from Navarro et al.(2019)’s work in the Luossavaara-Kiirunavaara AB’s (LKAB) Malmberget underground iron ore mine, Sweden. Navarro et al.(2019)’s model was developed based on102 fan-holes from five ore bodies and extrapolated to the full-scale in20 drifts with 5600 fan-holes from two orebodies. A multi-step transformation of the MWD parameters was carried out in order to minimize external influences other than the rock mass. The study shows the calculations of the variogram and kriging estimation in the 3D domain for six ring-blasts, from one of the ore bodies studied in Navarro et al. (2019)’s work to assess the continuity of the rock classes along the six ring-blasts in a 3D mapping model. For that, intermediate rings between the measured ones from the MWD have been estimated. The probability distribution of values in the entire domain of rings with measured samples has been plotted together with the rock classes identified by the blasthole paths. The results show high accuracy in the matching between the kriging and the values given by the MWD data, allowing to visualize smooth trends of different rock classes along the ring. The representation of the 3D mapping model for the six ring-blast shows clear fractured and cave-in zones developed along the drift that correspond to zones with geotechnical problems found, as from internal reports.

By Ruilin Yang

The vector sum peak particle velocity (PPV) of blast vibrations describes the blast vibration intensity more completely than the PPV of a single component waveform. It is more logical to use a vector sum PPV as a vibration limit than using a single component PPV. In 1980 the USBM recommended the frequency related peak particle velocity criterion. So far this method has been only applied to single component waveforms, but not to the vector sum PPV since there is no method available to associate a frequency to the vector sum PPV. The present paper describes a method to define a principal frequency associated with vector sum PPV. The method is based on the weighted average of the principal (zero-crossing) frequencies of the three tri-axial components at the time of the PPV.

Jan 1, 2015

By Daodu Opeyemi

This paper describes several damages of blasting operations on some case studies, analyzes causative factors, and emphasizes preventive measures. Due to several complaints from some host mining communities as a result of blasting operations; two quarries from Nigeria suburbs were visited for study. The blasting design parameters in the mining companies were examined. Also, the history and existing conclusion of the neighboring buildings were studied using structured questionnaire, personal contact and visual examination. From the study carried out, it was discovered that varying negative environmental and socio economic problems resulted from the effects of vibration and flyrock on the nearby agro mining communities. The consequences are not limited to distortion of landscape but also include extinction of some animals, poor agricultural productivity; such as damages to economic trees and reduction in the yield of crops, health problems as a result of shock resulting to psychological disturbances, communal conflicts, blast induced cracks of structures and sometimes total collapse of host agro mining buildings, thus indicating that most mines did not comply with the safety concept of the existing environmental laws and regulations. Based on the results of the study it was recommended that proper blast design of quarries/mines should be conducted and the compulsory use of seismograph will be crucial in developing predictions. Environmental impact assessment should always be conducted before, during and after each blasting operation. Other possible control of vibration, flyrock and airblast, are also discussed in the paper

Jan 1, 2009

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

By James T. Ludwiczak

Drilling and blasting in a Karst (sinkholes and mud seams) environment has long been a problem for blasters, miners, quarry operators, contractors, and developers. While one cannot change the geological conditions, one can take some measures during the bidding process and the initial preparation of the blasting program to help reduce some of the problems. During the geotechnical investigation and developing the test/core drilling grid, the owner/developer needs to take some additional measures that will provide important data to the blaster to help reduce the problems associated with blasting this type of geology. The owner/developer must also understand that, due to the geologic conditions, the results of the blasting will not be ideal and there may be additional blast-related costs. If provided the proper geologic data, the blaster can develop drilling patterns and blast designs that will help reduce some of the more problematic areas.

Jan 1, 2005

By Paul McAnuff, Alastair Grogan

In Canada, the only vibration regulations which apply across the entire country are intended to protect fish spawning areas. The Provinces and Territories regulate mines and quarries, and are responsible for setting vibration and airblast regulations. Some Provinces have set specific regulations, while others leave these restrictions to the mines inspectors who can set limits on a case by case basis. For the most part, it is left to individual municipalities to regulate blast vibrations and airblast from other blasting activities, which differ from jurisdiction to jurisdiction, and in some cases are not enforced. Blasters working in different jurisdictions have to be aware of the applicable regulations for the area they are working.

Jan 1, 2005

By Steve Kane

Lightning is a very real problem in the surface mining industry. Today, as adverse market conditions continue to influence the surface coal industry, it has become necessary that all functions of the surface mining process become as efficient as possible. High production with reduced manpower is the winning combination of staying competitive in the market place. We at AMAX Coal are committed to staying in the coal business, but we have always been committed to providing a safe work environment for our people and will continue to do so in the future. Approximately two years ago, our Midwest mines installed state of the art lightning detection and warning systems at our mines. This paper will cover its application at Delta Mine; the benefits and problems encountered, and the impact this system has had on Delta Mine.

Jan 1, 1992

By Ron Woolf, Corry Goumans

This paper describes rock slope remediation performed along America’s first Superhighway, the Pennsylvania Turnpike and in particular, the specialized drilling equipment designed and built by Pacific Blasting to complete this work. This S-month project was performed on an existing rock cut slope within the Bedford Narrows, a gap formed by the Juniata River through Evitts Mountain. These rocks are in the folded Juniata and Tuscarora Formations within the Valley and Ridge Province and strike northeast with near vertical to slightly overturned bedding.

Jan 1, 2001

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In-hole detonation pressure measurements are unusual in the production environment of a mining operation, partly owing to the hostile conditions to which recording equipment and pertinent probes must be subjected and, partly by the constraints of the production cycle. In recent decades, detonation pressure measurement techniques have been developed using low carbon resistors (LCR)-based gauges. They are cheap, relatively easy-to-operate, robust and with a high percentage of success in both open-pit and underground mining. Detonation pressure measurements are extremely important when carrying out numerical modelling to simulate explosive induced vibrations, since simulation results are highly dependent on the pressure-time history applied on the blasthole wall. Analytical equations have typically been used to model the pressure-time history; however, they usually do not adequately represent the behaviour of the explosive in terms of: peak pressure reached, rise time, mean frequency, decay and shape of the signal. Experimental records may be directly used instead of utilizing synthetic signals if they are available. In this work, (LCR)-based gauges are used to measure detonation pressure inside a production blasthole. The operation principle of the gauges utilized and the instrumentation layout is described in detail. A flexible resolution USB oscilloscope with high sampling rate has been used to catch the elusive pressure peak event. Measurements were carried out in production blasts fired with ANFO (0.86 g/cm3) in an underground mine––this also includes velocity of detonation (VOD) records––. A procedure based on the shock impedance matching has been developed to calculate the detonation pressure due to the characteristics of the gauges prevent its direct measurement. Detonation pressures obtained range from 1.71 to 2.97 GPa (248.01 to 430.76 ksi) which are in line with pressures calculated from the VOD records. Mean frequency and rise time analysis shows that 2 of 3 signals cannot be described using typical analytical equations.

Feb 6, 2023

By Catherine L. VanOmmeren

Emulsion quality characteristics such as shelf life, handling, and sensitivity are critical to the end-user. It is therefore important that the consumer be prepared to ask his suppher specific questions. To do so, he needs to have a basic understanding of what an emulsion is and how emulsion properties can affect safety, performance, and environmental impact. The criteria to be covered include: energy, velocity, sensitivity, minimum priming, shelf life, pumpability, effect of AN quality, over-the-road handling, and formulation. The consumer will learn how each of these properties can directly affect him. The information will enable him to set minimum standards in product selection, blending, and application.

Jan 1, 1992

By Joshua Hoffman, Braden Lusk, Kyle Perry

Despite its porous and lightweight characteristics, aluminum mesh is believed to have blast mitigation properties. The current use of the mesh includes fuel tanks for airplanes, boats, and fuel stations as well as light armored vehicles for the military. The mesh acts as an explosion suppressant by preventing fuel tanks from exploding when exposed to an ignition source. More recently, work has been performed to assess the ability of the mesh to mitigate blast pressures produced by high explosives.

Jan 1, 2009

By Sayantan Chakraborty, Kaushik Dey, SaKaushik Dey tyabrata Behera

Drilling and blasting is a popular excavation technique in the drift of underground mine. Faster completion of drift reduces the gestation period and thus longer blast pulls are attempted with longer drill holes. This compels the blasters to initiate higher charge quantity with higher confinements and ultimately results into blast-induced cracks beyond the desired periphery line of excavation. Assessment of the extent of these crack networks is difficult and often neglected. Near-field ground vibration models are often used as damage predictors (Dey, 2007, Yang et.al 1993, Holmberg et. Al 1979) but not necessarily deals with the positions of the cracks. Qualitative measurement of actual damage extent often measured using some geophysical tools, namely, P-wave velocity (Tezuka, 1995), seismic imaging (Dey, 2011), bore hole pressure monitoring (Brent and Smith, 1996), electrical resistivity (Grady and Kipp, 1993), GPR (Adams et.al, 1993) etc. Ground Penetrating Radar (GPR) is a similar geo-physical tool, which uses Electro-magnetic (EM) pulse for characterizing the medium. Similar to other geo-physical tools, GPR also comprises of a transmitter and one/multiple receivers to generate the EM pulse and receive the same after reflection/refraction from the medium(s) respectively. After its development in 1970s, GPR gained increased popularity due to its application in many important fields, namely, identification of buried objects, geological characterization, identification of geological disturbances etc. Thus, it is felt that GPR technique can be used to detect the invisible cracks inside the rockmass from the rock surface (wall and roof) itself. Understanding the same, field experimentations are carried out in an underground manganese mine in Central India, which operates on the ‘cut and fill’ method of mining at a depth of around 300m from the surface. Wedge cut blasting is carried out in the horizontal drifts of the mine using suitable blast design. A 1.6 GHz antenna was used for the GPR scanning, in which GPR transmitter transmits signals predominantly of the said frequencies. The signals get reflected back from any type of interfaces between materials in the target area, with different dielectric properties and is received by the receiver part of the ‘trans-receiver’ antenna and memorized in the Data Acquisition Unit (DAU). The data acquired is processed using a software. Ground vibration monitoring of the blasts are also carried out to develop a vibration predictor. The numerical analysis of near-field vibration predictor model results into the estimated vibration levels at the point of identified cracks. Introduction

Jan 1, 2019

By Rohan Stevens, Katsuhiro Kameyama, Osamu Iwata, Jinming Liao

In densely populated cities such as Hong Kong, where unoccupied space is becoming more valuable as the population grows, city planners are more often looking to underground space to meet the increasing need for transportation and services. Given the dense population of people, amenities and high-rise buildings above or near such underground space, it is essential to minimise any disturbance and potential damage during construction. Hence, the excavation of hard rock to develop such underground space can be highly restricted, expensive and time consuming. This is the case for many of the tunnels currently being excavated by drill and blast directly underneath Hong Kong’s busiest business districts and most popular residential areas.

Jan 1, 2013