Search Documents

By L. A. SCHOLL, J. K. CLEMENT

Among the problems investigated by the Bureau of Mines the coal- dust problem has received much attention. Several of the bureau's publications deal specifically with the subject. Bulletin 20° contains an account of preliminary experiments of the bureau to determine the explosibility of coal dusts as well as a review of pertinent literature. Bulletin 50 is a report of a laboratory study of the inflammability of coal dust. The first series of coal-dust explosion tests in the bureau's experimental mine at Bruceton, Pa., is described in Bulletin 56, and Technical Paper 56 presents notes on the prevention of dust and gas explosions in coal mines, and Technical Paper 84 discusses the causes of such explosions and describes methods and apparatus devised by engineers of the bureau for preventing and checking them. The present paper is a report of a detailed study of the bituminous dusts of Illinois mines, and is a part of the investigations conducted by the bureau in cooperation with the Illinois State Geological Survey and the department of mining engineering of the University of Illinois./ It is well known that bituminous coals like those found in Illinois yield dusts that may give rise to explosions of great violence. In order that proper methods might be devised for preventing dust explosions in Illinois mines it was considered desirable to obtain accu- rate information on the quantity and character of these dusts. Ex- periments and tests of dust explosions in an experimental mine as well as in a large steel gallery comparable in area of cross section to mine entries have been made by the Bureau of Mines. Similar experi- ments have been made in Austria, England, France, and Germany. Experiments under conditions similar to those of actual mining prac- tice are obviously more conclusive than tests made in a laboratory. On account, however, of the expense, time, and quantity of dust re- quired, it is not practicable to conduct large-scale tests in studying a large number of dusts and recourse must be had to laboratory apparatus and methods. Laboratory,devices for the study of coal-dust explosions have been devised by a number of investigators. Most of these were intended for qualitative tests only. Quantitative methods have been devised by investigators of the English and French mining-experiment stations." In the experiments described in this report, laboratory tests of inflam- mability were made with an apparatus devised by Dr. J. C. W. Frazer, formerly a chemist of the Bureau of Mines. Laboratory tests of inflammability have been made on more than 500 samples of dust from 100 representative Illinois mines. As a result of these tests it may be stated that: 1. The coals of Illinois when ground fine enough yield highly inflam- mable dusts which when suspended in air may give rise to violent explosions. 2. In the majority of the mines of the State the dusts adhering to the ribs are inflammable. In about one-fourth of the mines the quantity of rib dusts present in the entries is sufficient to form an explosive mixture with air. 3. Most of the road dusts are inflammable when ground to a suffi- cient degree of fineness.

Jan 1, 1916

By Ivette E. Torres

The series summarizing the prices of the major nonferrous metals on the stock exchanges of the United States and the United Kingdom (London Metal Exchange) has been continued this year in tables 22 and 23. Time constraints have prohibited preparation of other price information that has appeared in this study in previous years. Users are urged to consult the 1993 U. S. Bureau of Mines publication Metal Prices in the United States through 1992, which gives an analysis of historical price series and trends, or the 1993 edition of Mineral Commodity Summaries for current U.S. prices on non fuel commodities, and to utilize U.S. Department of Energy sources for information on fuel material costs.

Jan 1, 1994

By Lloyd A. Morley

This report details the continuation of mine power systems transient research under USBM Grant G0155003. The purpose of the work, which commenced under Grant G0133077, is the elimination of safety hazards created by transients" and the objective is to provide knowledge about transients existing in a-c and d-c coal mine power systems. The report chapters cover theoretical background, instrumentation, and experimental investigations. The instrumentation discussion scans measurement problems and considerations plus the development of a low-cast peak-detector. Transient data from in-mine measurements are presented and include high-voltage distribution and d-c trolley systems. Extremely unique field exercises are described involving actual power equipment connected on the surface to duplicate typical underground coal mine system arrangements. Here, transients on high-voltage distribution resulting from vacuum circuit breaker operations could be observed under controlled conditions, and work centered around how surge capacitors effect transients. Using the in-mine and staged transient data, specific conclusions and recommendations are made with emphasis on high-voltage distribution.

Jan 1, 1977

By C. M. K. Boldt

This report summarizes five separate Bureau of Mines contract studies on the use of aerial photogrammetry, satellite transmission of in situ instrumentation information, and satellite imagery to monitor and update mine waste embankment data. The equipment used, methods applied, results, recommendations, and cost analyses are presented along with a bibliography of related investigations.

Jan 1, 1987

By Oliver C. Fursman

The Bureau of Mines undertook this investigation to study methods of utilizing red mud residues from production of alumina from bauxite. Pilot-plant tests were conducted using Jamaican and Surinam red muds. Both the carbon-lime-soda sinter process and electric-arc smelting with coke and limestone were employed to recover iron and alumina. Alumina recoveries of 85 to 90 percent were obtained by the sinter process; although iron recovery was about 80 percent, the magnetic product was finely divided and difficult to separate from the gangue. Smelting red muds in the electric-arc furnace produced a pig iron with 98-percent recovery of iron; up to 84 percent of the A1203 was recovered by leaching the calcium aluminate slag with Na2C03 solution. A titania product assaying 96 percent TiO2 was recovered from the nonmagnetic portion of Surinam red mud sinter by extraction with H2SO4. Leached calcium aluminate slags and brown mud (from the combination Bayer process) are possible raw materials in the manufacture of portland cement.

Jan 1, 1970

By Joseph N. Harstead

This Bureau of Mines report provides information on the first 49 water-flood projects (or units) in Nebraska. All injection was in the ?D? or "J" Cretaceous sands of western Nebraska. Specific data presented include location, map, discovery and development, water supply and injection, oil and water production, estimates of oil in place, primary and secondary recoveries. The 49 projects studied) including four dual-zone projects, should recover about 126.5 million barrels of oil. Eighty-six percent of the estimated oil had been recovered by the end of 1966. Abundant water was found near most projects.

Jan 1, 1967

By Ruth F. Brinkley

This circular summarizes the research and technologic activities and publications of the Federal Bureau of Mines Division of Explosives Technology4/ during fiscal year 1959 (July I) 1958-June 30, 1959). Part I briefly describes the programs that were active during the report period and presents a summary of some of the information not published elsewhere. In many instances the results are only preliminary and are subject to revision on the basis of continuing investigations. Detailed reports of all programs not security classified will be made later. Part II lists and describes briefly the publications of the Division during fiscal year 1959. If the published material has some bearing on activities still current during the report period, this is indicated by references in Part I.

Jan 1, 1961

By David C. McHuron

The U. S. Bureau of Mines in their continuing research into sealants, selected MBAssociates to design, build, and test equipment and evaluate sealant as to its effectiveness is shale degradation. There were 20,050 sq.ft. of coal mine roof sprayed with a mine sealant and as a result, it has been estimated that the sealant coated roof has from 50% to 95% less roof falls than that roof which was not coated with sealant.

Jan 1, 1980

By J. D. Sargent

Selenium might be described as a paradoxical element, being a metal or a nonmetal, a conductor or nonconductor, amorphous or crystalline, colorant or decolorant, and a hydrogenator or dehydrogenator. Selenium was discovered in 1817 by the Swedish chemist, Berzelius, while studying flue dust from the lead chambers of the sulfuric acid works at Gripsholm, Sweden.

Jan 1, 1954

By Andrew B. Cecala

The Bureau of Mines conducted laboratory and in-mine tests on the Racal airstream helmet (Model #AR21) to evaluate its protection efficiency. Laboratory tests indicated that as ambient air velocity increased, the protection offered by the helmet decreased. In tests conducted at several coal mine long-wall sections with face velocities under 400 fpm, the helmet was 84 pct effective at reducing respirable dust in the miner's breathing zone. However, at a high-velocity section, 1,200 fpm, the efficiency of the helmet was significantly reduced, confirming our laboratory results.

Jan 1, 1981

By F. W. Cox

Exhaust emissions were measured from 25 aircraft turbine engines using Jet A fuel. Analytical apparatus, procedures, and results are described. Carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and aldehydes were measured at engine operating modes representing power levels used in airline operation. Carbon monoxide, hydrocarbon, and aldehyde emissions were highest at idle and lowest at takeoff; oxides of nitrogen were lowest at idle and highest at takeoff. Of the total oxides of nitrogen emitted, nitrogen dioxide constituted from 10 to 100 pct, depending on the exhaust gas temperature. Engines retrofitted with smoke-reducing burner cans produced less carbon monoxide, hydrocarbon, and aldehyde emissions, and slightly more oxides of nitrogen then engines with standard burner cans.

Jan 1, 1972

By Terry J. Close

The highly-mineralized 43,700-ha Rapid River study area, on the southeast side of Hells Canyon Wilderness and west of the village of Cuprum, in Adams County, western-Idaho, was investigated in 1992 by the USBM (U.S. Bureau of Mines) in conjunction with its Idaho Land Assessment Program. The 1992 study updated data gathered during the USBM's 1974-76 Wilderness investigation. The studies consisted of the evaluation of 61 mineralized sites and the estimations of tonnages, grades, and minability of these sites. Most of the sites studied are in two mineralized locales--Windy Ridge and Jackley Mountain. A few isolated sites, peripheral to the two locales, were also examined. The 61 sites contained more than 340 mine and prospect workings, including about 10,300 meters (34,000 feet) of underground workings, plus 134 drill holes.

Jan 1, 1993

By Vernom F. Swanson, George E. Fish

A study was made during 1959-60 of reported nelsonite occurrences in Nelson and Amherst Counties, Va. The investigation was limited to core drill- ing on one deposit and beneficiation studies on three deposits. Three diamond-drill holes totaling 562 feet were drilled on the E. M. Hughes property to determine subsurface continuity. Although outcrops as much as 30 feet wide were present on this property, the only nelsonite intersected in the holes ranged from 4 to 18 inches thick. The ilmenite content of the core ranged from 50 to 75 percent. These nelsonite deposits are of secondary importance as a source of titanium, being small, rarely exceeding 1,500 feet in length and 30 feet in width, but they are high grade. Due to the proximity of some of the bodies it might be possible to mine several of them as one operation feeding one mill. Electromagnetic separation on composited samples recovered 83.0 percent of the Tio as an ilmenite concentrate in 68.5 percent of the weight. Two flotation procedures were developed. The first method, using oleic acid as a collector and fluo silicic acid as an apatite depressant on deslimed feed, produced an overall recovery of 59.3 percent in batch tests. The second procedure eliminated desliming. Laurylamine hydrochloride removed silicates in an acid pulp followed by an alkaline apatite flotation with oleic acid as the collector and dextrine as the ilmenite depressant. The ilmenite-rich tailing represented a 66.2-percent recovery of Tio in the batch tests.

Jan 1, 1964

By L. D. Tracy

The first study of this subject hits been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal-mining industry to standardize the forms of leases, and so avoid some of the abstruse and ambiguous clauses which slay be found in many of them and the consequent liability of costly litigation. In some of the publications of the Illinois Mining; Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the 'State have been divided into eight geological districts, each district being treated separately. This report covers District No. VI of that classification, and it is hopped that studies of the other districts will be completed in the near future and similar results published.

Jan 1, 1926

By M. L. Odenbaugh

The viscosity reduction effect of varied concentrations of leonardite (a naturally oxidized form of lignite) and leonardite-caustic on the rheological properties of a standard bentonite drilling fluid was studied and evaluated. The minimum plastic viscosity was found to occur at application rates of 4 lb of leonardite and 1.33 lb of caustic per barrel of drilling fluid. Leonardite-caustic treatment was not beneficial in treatment of salt-contaminated drilling fluids. Although filter loss rate was reduced; both yield values and gel strength were increased. Compared with other viscosity control agents) including quebracho) ligno-sulfonate) humic acids extracted from leonardite) as well as other reaction products of lignite) leonardite is less effective at low application rates but is an effective treating agent at rates of 2 Ib/bbl or more. Considering the comparable merits of the substance tested) the major factor in determining which agent to use should be based on cost consideration.

Jan 1, 1967

[ ]

Jan 1, 2012

By J. H. Heginbotham

As part of the total metallurgical system to recover metals from secondary resources, the Bureau of Mines conducted froth flotation research, using cationic reagents to recover glass from urban refuse. Batch flotation tests showed that high-quality cullet can be obtained from glass-rich aggregates derived from municipal incinerator residues and unburned refuse. This was confirmed by pilot plant operations treating 350 pounds of flotation feed per hour. Aggregates containing 85 to 90 percent glass were wet-ground to minus 20 mesh, deslimed in two stages, and fed to flotation cells. The glass was selectively floated using an amine collector, usually in an amount under 0.2 pound per ton of solids in the feed. The glass concentrates from the rougher cells were cleaned by refloating two or three times. Over 90 percent of the glass in the deslimed feed was recovered in the cleaned concentrates.

Jan 1, 1978

By M. J. Ackerman, C. R. Waine, W. M. Merritts, L. P. Mokwa

Tests were conducted in the Pocahontas No. 4 coalbed in southern West Virginia to determine if successful degasification techniques, developed during an earlier study in the Pittsburgh coalbed, would be effective in removing methane from those usually more gaseous coals. Specially designed long-hole drilling equipment and Bureau of Mines continuous recording devices were used to measure the quantity and methane content of the ventilating air during the investigation. Infusions were made with water at normal waterline pressures ranging from 200 to 220 psi or at pump pressures ranging from 400 to 650 psi. Results of the tests showed that methane emissions from free-flow bleeder holes were as much as 131 cfm. Infusions of some of the holes increased the methane emission from other holes and from the exposed coal surfaces near the working areas as much as 1,540 cfm. The methane content in the main return-air currents after infusion was reduced more than 86 percent of the amount recorded before tests were made.

Jan 1, 1963

By C. P. Lazzara, Y. Miron, A. C. Smith

This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, utilizing the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2)

Jan 1, 1992

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977