Search Documents

By Fadeela Saloojee, Frank K. Crundwell

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidising agent. This work shows how the performance of pressure leaching circuits may be improved by optimising the configuration of autoclaves and the heat-removal method. The objective was achieved by creating an autoclave model by combining mass balances, energy balances and population balances. A base-case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity–increase options include circuits in which the additional autoclave is added in parallel, in series and in series with thickening between the two autoclaves. The copper extraction, productivity and cooling requirements for these options are compared. The series circuit with inter-stage thickening has the highest extraction and productivity, however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water and flash recycling. The flash-recycle option results in the highest copper extraction, and the quench-water option gives the lowest copper extraction. INTRODUCTION Background Copper sulfide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work. In the pressure leaching process, sulfide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidising agent, usually oxygen, is required to oxidise sulfide ions to sulfate ions. The oxidation of sulfur to sulfate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2015

By A. Fredriksson, R. Christiansson, I. Staub

A theoretical model based on DFN models and 2D DEM numerical modelling has been developed for evaluating the rock mass mechanical properties. The description of the methodology is non-site related and can be applied in any site for this type of characterisation. The methodology was developed in the frame of the Site Investigation programmes for a Deep Repository for spent fuel in Sweden, and validated on sets of data coming from the Äspö Hard Rock Laboratory. Un modèle théorique base sur des modèles probabilistiques de réseaux de fractures et sur un modèle numérique DEM 2D a été développé dans le but de déterminer les propriétés mécaniques de la masse rocheuse. La méthodologie développée peut être appliquée à tout type de site pour ce genre de caractérisation. Le modèle a été élaboré dans le cadre des programmes de recherche d’un site d’enfouissement des déchets nucléaires en Suède, et validé par une application au laboratoire de recherche souterrain à Äspö. Ausgehend von DFN-Modellen und 2D DEM numerischen Modellierungen wurde ein theoretisches Modell für die Auswertung von mechanischen Eigenschaften von Fels entwickelt. Die Methodikbeschreibung ist nicht standortspecifisch sondern kan überall für diesen Typ von Standordkarakteriserung angewendet werden. Die Methodik wurde in Schweden im Rahmen der Standortuntersuchungsprogramme für die Endlagerung von verbrauchten Brennelementen entwickelt und ist mit Hilfe von Daten des Äspö Hard Rock Laboratory validiert worden

Jan 1, 2003

By G. F. Vander Voort

The accident at Unit No. 2 of the Three Mile Island nuclear reactor (TMI-2) on 28 March 1979 was the worst nuclear accident in US history and crippled the nuclear industry. An international Vessel Investigation Project was formed to assess the integrity of the vessel. However, it was not possible to remove specimens from the lower head until January?March 1990. Fourteen of the fifteen specimens removed by electrical discharge machining were from under the debris pile that accumulated on the lower head due to melting of approximately 19 000 kg (45%) of the core. Specimens were previously cut from the lower head of a cancelled reactor of very similar size and design destined for Midland, Michigan. These specimens were subjected to controlled heating cycles with peak temperatures from 800°C to 1100°C for periods of 1 to 100 minutes. The initial study qualitatively compared the structures in the 15 specimens from TMI-2 to the control specimens from the Midland lower head. The writer used the same specimens and employed microindentation hardness traverses, electron microprobe analysis, and selective etching followed by quantitative metallography (by image analysis) to obtain a far more detailed description of the thermal exposure experienced.

Jan 1, 2013

The development of 3D multi-parametric models facilitate the provision of resource information well in advance of the mining face. Using the model, one can evaluate mining areas not only for grade and tonnage predictions but also for predictions of rock mass quality. Blast design and milling requirements can be derived from the rock mass quality predictions. This information can be used for overall mine planning and evaluation, costing, production optimization and slope design. This allows the full range of mining activities and costs to be interconnected, thereby lowering costs and improving efficiencies through the application of the multi-parametric model. Feasibility studies for new projects require an expected budget expenditure estimate to within 5% of actual costs. This level of accuracy is expected by mining companies and investors but cannot be achieved without a sound knowledge of the rock mass variability. By developing a 3D multi-parametric model as part of the feasibility study and using the same geological model exploration boreholes, a significantly better understanding of the rock mass conditions can be obtained. This rock mass information can be used for equipment selection, economic pit layouts, processing plant design, underground mining layouts and support requirements, to name but a few design parameters that depend on rock mass conditions. The initiative at Anglo Platinums, Potgietersrust Platinum Ltd.?s (PPRust) operation, has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. The ore reserve model has gained international acceptance as an invaluable tool for a mining operation. Certainly most financial organizations will not invest in a mining project that does not have an ore reserve model. There is the potential for multi-parametric models to be recognized as vital tools in the mining process, as is the case with ore reserve models.

Jan 1, 2007

By J. -C. Tricket, W. A. Düweke, S. Kock

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological model seven further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip.. Keywords: 3D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; Seismic Micro Technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2004

By K. Osburn

South Deep Gold Mine, owned by Gold Fields Ltd., is situated near Westonaria in the Gauteng Province of South Africa and mines the conglomerate bands of the Upper Elsburg reefs (Mondeor Conglomerate Formation) of the Witwatersrand Supergroup and the Ventersdorp Contact Reef (VCR) of the Ventersdorp Supergroup. The stoping and underground developments are mechanized. The Upper Elsburg reefs are mined by a variety of mining methods, including mechanized drift and fill, modified drift and bench, longhole stoping, and low-profile mining. Optimal mine design and scheduling for deep-level mechanized mining are complex, and success is highly dependent on detailed, robust, and accurate geological and geostatistical models. Geological structures significantly influence the sedimentological characteristics, distribution, and preservation of the Upper Elsburg reefs and VCR. Accordingly, particular emphasis is placed on the generation of a mine-scale structural model that accommodates the relationships between the older north-trending fault systems (West Rand and Panvlakte faults) and younger east-trending dextral wrench faults. Results from underground mapping, borehole intersections, and highresolution three-dimensional seismic data have been integrated to produce coherent three-dimensional geological models. The Upper Elsburg reefs suboutcrop against the VCR and comprise an easterly diverging clastic wedge, thickening from the suboutcrop position, to approximately 130 m at the mine?s eastern boundary. The Upper Elsburg reefs are characterized by conglomerate and quartzite bands forming multiple, stacked, upward-fining unconformity-bounded couplets. Palaeocurrent directions are dominantly from west-northwest to east-southeast, indicating that the more proximal deposits are preserved close to the suboutcrop, with distal facies to the east. Sedimentological modelling is applied to individual stratigraphic units and caters for facies definition. This is achieved through channel width (CW) kriging and fitting of type sections to borehole and mapping data. Homogenous geological geozones for each stratigraphic unit are thus defined within individual structural blocks on the basis of those sedimentological parameters that have been found to have a positive spatial correlation to gold concentration. These geozones then serve as constraints to the evaluation of the orebody. This contribution presents a summary of the modelling processes that are currently applied in the development of high-confidence, timeously produced geological models that are essential input for mineral resource estimation and mechanized mine planning and scheduling.

Jan 1, 2014

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

Gravity-driven rock falls account for a large proportion of all fatalities and injuries in underground mines. Potentially unstable blocks of rock are found in the hanging wall of excavations, which may be delineated by natural joints or stress fractures. These blocks, referred to as keyblocks, will fail if their weight exceeds the support capacity or if they are located between support units. This paper describes a computer program which simulates blocks in the hanging wall of an excavation based on measured properties of fractures and joints. Keyblocks are identified and placed at random locations in a predefined excavation. The keyblocks are tested against the support to determine whether they fail the support, drop out between the support or are stable. By repeating the procedure several thousand times, statistics of the probability of failure of the keyblocks are obtained. This approach allows the relative hazard associated with different types of support or excavation orientations to be obtained. It is concluded that a probabilistic approach is suitable for the evaluation of supports effectiveness in situations where large numbers of discontinuities or stress fractures are exposed in excavations.

Jan 1, 1998

By H. Yavuz

Closed form solutions assume opening shape to be circular to simplify the calculation of the ground response curve for the design of underground openings. However, in mining and civil engineering works, non-circular openings are commonly excavated. Therefore, there is a need to estimate the ground response curve for such openings. In this respect, a simple model for circular, arch and rectangular shape underground openings subject to a hydrostatic stress field is the aim of this study. A comprehensive numerical modelling, using the finite difference method, based on numerical modelling code FLAC version 4.0, was carried out. In addition to shape of an opening, the effect of rock mass strength, opening size, in situ stress on strain (tunnel deformation to tunnel radius) of the opening in response to applied support pressures was investigated parametrically by developing models for each specific condition. The strain results for each excavation shape obtained from this large number of models against the normalized strength of rock mass and internal support pressure with in situ stress magnitude were evaluated by multiple regression analysis. As a result, a model that was well correlated to data was developed for an overall estimate of the ground response curve depending on relevant effecting parameters. The regression coefficients of the model were given for estimating both roof and sidewall response curve of each excavation shape. The model was verified by statistical tests and by an analytical solution. Diagrams were also established to highlight the influence of relevant parameters and to estimate the support pressure for a stable opening staying within the acceptable limits of strain. Strains occurring in a rectangular opening are found to be larger than those in the arch and circular openings for the other fixed parameters. In the mean time, larger strains occur around an arch shape opening than a circular opening.

Jan 1, 2006

By D. M. MacHunter, T. Lawson, D. K. Henderson

The development and commercialization of new generation high tension electrostatic separators has provided a basis for simplifying mineral separation plant circuitry. The inclusion of new design features including insulated plate electrodes that have resulted insignificantly improved separation efficiencies in electrostatic separators are described. The increase in separation efficiency has resulted in a reduction in the number of treatment stages required to produce final high grade mineral products. Comparative performance data on different feed types are presented. A comparison between mineral separation plant flowsheets using both conventional and new generation high tension electrostatic separation technology is presented. A 55% reduction in the number of installed electrostatic separators and a 36% reduction in plant area was achieved through the use of this new electrostatic separation technology.

Jan 1, 2003

By K. J. Oliver, A. G. Meyers, S. P. Hunt

Deformation Rate Analysis (DRA) and porosimetry have been used to demonstrate the “stress memory” effect in rock and to estimate the vertical in-situ stress in samples of fine-coarse grained sandstone and carbonaceous mudstone. The results of this study indicate that the stresses predicted using both methods are similar to those determined from depth and density of the overburden rocks. The results confirmed that DRA was still applicable even when the core had been sampled 18 months prior to testing. Additionally, the DRA results were modelled using the software PFC2D. A uniaxial test was modelled using the same rock parameters as those observed for the actual core samples. This numerical technique can be used as an aid for DRA results analysis, and can also be used to predict the minimum stress level at which the DRA technique is applicable. The results confirm that any rock mechanics laboratory having standard test equipment could apply the DRA method combined with standard UCS testwork to determine the in-situ stress. Mit der Analyse der Deformationsrate (DRA) und der Anwendung der Porosimetrie wird der Spannungsgedaechtnisseffekts (Stress Memory Effect) im Fels demonstriert, und es werden Abschaetzungen fuer die vertikale in-situ Spannung einer Probe aus mittelgrobem Sandstein und carbonierten Lehmstein getroffen. Die Ergebnisse dieser Untersuchung zeigen, dass die mit Hilfe dieser beiden Methoden ermittelten Spannungen sind vergleichbar. Die Ergebnisse bestaetigen, dass DRA noch anwendbar ist, wenn die Proben schon 18 Monate vor Untersuchungsbeginn gesammelt worden sind. Darueber hinaus wurden die DRA Ergebnisse mit Hilfe des Sofwarepakets PFC modelliert. Ein einaxialer Test wurde mit genau die gleichen Felsparametern, die fuer die eigentliche Probe gelten, modelliert. Diese numerische Methode kann sowohl als eine Unterstuetzung fuer DRA Ergebnisanalyse als auch zur Ermittlung der minimalen Spannung, bei dem die DRA Methode noch anwendbar ist, herangezogen werden. Die Ergebnisse bestaetigen, dass jedes Felsmechaniklabor, das mit den ueblichen Testgeraeten ausgestattet ist, die DRA Methode in Kombination mit dem Standard UCS Testarbeit zur Bestimmung der in-situ Spannungen anwenden kann. L'Analyse du Taux de la difformité (DRA) et les porosimetry ont été utilisés démontrer le " effet de la mémoire " du stress dans roc et estimer le stress dans - situ vertical dans échantillons de grès du grained fin grossier et mudstone carbonifère. Les résultats de cette étude indiquent que les insistances ont prédit utiliser les deux methods est semblable à ceux déterminés de profondeur et densité du surchargez des rocs. Les résultats ont confirmé ce DRA était encore même applicable quand le coeur avait été goûté 18 mois avant tester. En outre, les résultats DRA étaient des modelled qui utilisent le logiciel PFC2D. Une épreuve de l'uniaxial était modelled qui utilise les mêmes paramètres du roc comme ceux observé pour les réels échantillons du coeur. Cette technique numérique peut être utilisée comme une aide pour DRA résulte analyse, et peut aussi être utilisé pour prédire le niveau du stress minimum à que la technique DRA est applicable. Les résultats confirment que tout laboratoire des mécaniques du roc qui a le matériel de l'épreuve standard pourrait appliquer la méthode DRA combinée avec testwork UCS standard pour déterminer le stress dans - situ.

Jan 1, 2003

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

By S. Kamalpour

It has been observed that the productivity of ferromanganese furnaces, and the stability of metal and slag compositions, vary considerably according to the type of coke used as reductant. However, the desired properties of coke for optimum furnace performance are not well understood. In this investigation, the behaviour of four cokes, which exhibited a wide range of performance in ferromanganese production, was investigated by means of laboratory simulations of reducing conditions in the furnace. The Stationary Charge in Controlled Environment (SCICE) technique was used to simulate the conditions in the furnace shaft. Batches of raw materials, mixed in the same proportions as used in practice, were heated at fixed rates to 900, 1100 and 1300°C then cooled. The mass loss was used as a measure of the degree of reduction. Conditions in the lower part of the furnace were simulated by means of melt-reduction experiments in which lumps of coke were drilled out to form crucibles in which enriched ferromanganese slags were reduced at 1500 and 1550°C then cooled. An examination of the raw materials and the cooled, reacted charges using a variety of analytical and characterization techniques enabled the sequence of reaction and changes in morphology of the raw materials to be followed. This enabled an understanding of the behaviour of the cokes during reduction to be developed, which was then used to explain the observed performance of the cokes in practice. By relating the observed behaviour of the cokes in the laboratory tests to measurable properties of the unreacted cokes and to their observed performance in practice, it was shown that to achieve high productivity and good furnace performance, cokes should be selected to have moderately high reactivity towards CO2 (Boudouard reactivity) relative to conventional iron blast furnace cokes.

Jan 1, 2004

By C. D. K. Gauert

High-pressure waterjet technology is proposed as an alternative tool for selective underground mining of high-grade ore sections in stratiform orebodies showing a preferred ?bottom? or ?top? enrichment such as the Witwatersrand reefs and the Bushveld Complex platiniferous reefs. This technique, utilizing known mining technology together with more advanced machinery and additives as used in industrial and cleaning applications, may lead to an increased life-of-mine (LOM) for mining operations. A series of experiments was successfully carried out in a laboratory on Witwatersrand quartzite material, indicating acceptable cutting performance. Mining volumes by selectively cutting of reef portions are considered to be comparable to traditional drilling and blasting. Economic advantages of waterjet mining include energy savings due to the lower quantity of gangue rock to be hoisted to surface, as well as savings by a decrease in the usage of blasting materials. Capital expenditure of waterjet cutting, if applied on a broad scale, could be lower in the long term than that of conventional drilling and blasting methods. Mining by the application of high-pressure waterjet technology could become a competitive ?green technology? improving the economics and safety of labour-intensive mining operations. This paper suggests that waterjet cutting at an industrial scale can become a routine hard-rock mining technique in the future. Keywords waterjet cutting, high pressure, mechanized narrow reef mining, abrasive agents, costs, selective mining.

Jan 1, 2013

The Skorpion process comprises three processing steps, atmospheric leaching in sulphuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the route causes of the crud formation in the solvent extraction circuit and optimisation strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica

Jan 1, 2007

By M. Bhandari, D. Norval

The bulk of plain carbon steel is produced through conventional Basic Oxygen or Electric Arc Furnace routes where the development of the AC Ladle Furnace has made it possible to also produce alloy steels. Smaller Ladle Furnaces have limitations such as lower efficiency; high electrode consumption and diminutive yields rendering them uneconomical to operate and making the processing of low carbon steel grades difficult due to carbon pick up. The demand for special steels and alloys with strict specifications is increasing while commodity prices remain competitive. The production of special steels and alloys have specific process control requirements and the development of the induction melting furnace (IMF) has made it possible to produce smaller batches economically. Refining and alloying of the melt in the IMF further enhance the efficiency. The INDUREF furnace offers increased productivity and flexibility through increased thermal efficiency and can be utilised for holding molten metal for further processing such as granulating, atomising, nitriding, alloy additions and desulphurisation of Ferro-alloys and steels. The system utilises a specially engineered ladle which is placed in an induction-heating assembly comprised of a stationary water-cooled copper coil and lamination packs. The addition of equipment for vacuum degassing and decarburisation of steels and alloys is also feasible. Benefits are: ? No electrode consumption or carbon pick-up ? Lower installation, operation and maintenance cost. ? No line-flicker facilitates operation on a weak power grid. ? Good power factor and balanced load ? No skull formation and reduced refractory consumption ? Higher yield of Fe-alloys ? Automatic controlled stirring

Jan 1, 2004

This paper reviews the history of refractory materials, highlights the development of refractory technology over the years, draws attention to the technology behind these materials, and comments on future developments in this field. By walking the path with refractory materials, from their initial uses in BC times, to the composite materials that are used nowadays, and the nanotechnology developments that are currently taking place in this field, the reader will come to agree that refractory materials are indeed very ?cool?! Keywords: refractory materials; bricks; monolithic materials.

Jan 1, 2008

Virtual Reality (VR) simulations are excellent tools for training, education, simulation of abnormal and dangerous conditions in mines and solving complex problems. Although the concept of VR has been around for nearly half a century, it has taken recent advances in hardware and software to bring this technology to within the budgetary reach of ordinary users and researchers. VR is now successfully being used in the minerals industry for: data visualization, accident reconstructions, simulation applications, risk analysis, hazard awareness and training. The Institute of Sustainable Minerals Industry, Advanced Computer Graphics and Virtual Reality Research Group (SMI-VR) at the University of Queensland, established in late 2000, has been involved in developing VR applications for the minerals industry in conjunction with various research centres. This paper illustrates the benefits of using advanced computer graphics and VR techniques in the minerals industry with some examples of applications developed.

Jan 1, 2003

By G. J. de Korte

Dense-medium beneficiation of fine (minus 0.5 mm) coal is not a new concept and has been used in South Africa previously. The dense-medium fine coal plant at Greenside Colliery operated for almost 18 years and, despite proving a difficult plant to operate, did succeed in producing a fine coal product with a low ash content of 7%. No other beneficiation process available could achieve this. Dense-medium beneficiation of fine coal was also used in other countries, of which the plants at Homer City in the USA and Curragh in Australia were the best known. The first application of dense-medium cleaning of fine coal was, however, at the Tertre plant in Belgium1. This plant was built in 1957. About nine years later, a second fine coal dense-medium plant was built at the Winterslag Mine, also in Belgium. According to reports, this plant operated satisfactorily for a period of some 17 years.

Jan 1, 2002

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007