Search Documents

By Frank Agyemang, Zainab Nasrullah, Richard LaDouceur, Mehran Saddat

To sustain the circular economy, defence applications, and other renewable technologies, recycling rare earth elements (REEs) and other critical elements from their secondary resources is important. This cause has resulted in rigorous research and development for viable extraction and separation of REEs. Previously, Sm-Co recycling has been done with technologies, which fall under the categories of pyrometallurgy, physical separation, and hydrometallurgy. All these methods have limitations associated with energy, cost, and environment. Reportedly, the chemical leaching technology has successfully recovered and separated Sm-Co. Still, it has limitations associated with slow mass transfer and leaching kinetics, and there is a need to intensify the process to make it time efficient. This approach has also adversely impacted the environment by an extensive use of toxic, corrosive, non-selective, and expensive reagents. In this research study, chemical leaching of Sm-Co was performed using this new class of solvents, Deep Eutectic Solvents (DESs), which fall under the category of ion metallurgy. Four different DESs were used, proven to be green, non-toxic, biodegradable, cheap, and selective for cobalt over samarium by 82% leaching conversion. To improve the slow mass transfer and leaching time, this new technology of resonant vibratory mixing (RVM) was also tested. RVM intensifies mixing by establishing near instantaneous, low energy mixing conditions through resonance. It has been shown to improve the adsorption kinetics and was tested for the leaching kinetics. Four combinations of DESs were prepared, which are made up of two quaternary salts: Choline Chloride and Tetra Butyl Ammonium Chloride, and three organic compounds: Oxalic Acid, Urea, and Ethylene Glycol. These combinations were used for chemical leaching of Sm-Co with leaching factors of time, temperature, and type of DESs. After leaching, the samples were tested with and without resonant vibratory mixing with conditions of time, intensity (%), and type of DESs. Samples were analysed with Induced Coupled Plasma - Optical Spectroscopy (ICP - OES). Future work will involve a life-cycle assessment to assess the RVM technology with other conventional mixers, and an extensive study of DES properties to improve selective leaching.

Feb 1, 2025

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jason Navoyski, Jennica L. Bellanca

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos using the Unity game engine. The simulation videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories using graphic simulation. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Jun 1, 2023

By B. G. White

Traditional interpretations of vein ore deposits in the Coeur d' Alene Mining District, such as the view that these deposits formed in a transcurrent tectonic regime during the Precambrian, are being supplanted by the view that the deposits (1) formed in low-grade metamorphic shear zones similar to those that host an important type of gold deposit, (2) display features, such as wall rock carbonate zoning and vein zoning, that are common to ore deposits elsewhere, and (3) are probably Mesozoic and possibly related to emplacement of the Idaho batholith. In recent years, new interpretations have led to major ore discoveries that are likely to extend the life of the district for decades.

Jan 1, 1998

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs.Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By Douglas G. Brookins

Clay mineralogic studies of ore versus barren rocks in the Grants mineral belt show that some combination of chlorite (rosette form), illite, mixed layer illite-montmorillonite, (- Mg-montmorillonite) are penecontemporaneous with uranium minerals in trend ore; these same clay minerals plus kaolinite are related to the roll type ore near the main redox front of the Grants mineral belt. Clay minerals from barren rocks are characterized by a greater abundance of Na-montmorillonite, kaolinite, and face-to-edge form chlorite. Chlorites from ore zones contain much more vanadium than do chlorites from barren rocks. Trend ore probably formed from southeasterly flowing waters following paleochannels in the Late Jurassic. These deposits are found almost entirely in reduced rocks, and organic carbon may have been an important reductant to remove U-V-Se-Mo from solution as carbonate from ore zones contains some organic carbon based on stable iso¬tope studies. Uplift, remobilization and reprecipitation of some of the trend ore resulted in the formation of redistributed ore, some of which possesses a roll type geometry. Mineralization for the roll type ore was apparently controlled by sulfide-sulfate equilibria at or near the main redox front in the Grants mineral belt. Trend and roll type ore possess different assemblages of clay minerals and different trace element abundances. Laramide faults cut both trend and some roll type ore. Stack ore is found in Laramide fault zones. Limited oxygen isotopic data from clay minerals in two mines at Ambrosia Lake in reduced rocks indicate probable preservation of ancient, formational waters and no evidence for infiltration by young meteoric waters. This information, plus the pre-Laramide faults, suggest, but do not unequivocally prove, that the main redox front has been relatively stable since its formation, probably some time in the Cretaceous. Younger encroachment of the redox front in post-Laramide is proposed by others, however, and the problem is unresolved. Uranium for the deposits was most likely carried in solution as an oxyion, probably as (UO2(CO3)2.2H2O)2- or (UO2(HPO4)2)2-, although organic transport cannot be entirely ruled out. Oxyions of vanadium, selenium, molybdenum and possibly arsenic and antimony, are interpreted from Eh-pH diagrams to have been segregated and transported with U6+ soluble species and precipitated when a chemically reducing environment was reached. The rare earth elements are also enriched in ore zones, but it is not clear if they were transported with the U-V-Se-Mo-(As)-(Sb) suite or derived from a more local source.

Jan 1, 1980

By Marko Oosthuizen, Charl P. Botha, Lidia Auret, Annelette Malan, Marthie de Leeuw

Flotation performance is affected by upstream disturbances (e.g., mineralogy, water quality, flow rate) and controlled variables (e.g., pulp level and air addition). Process disruptions can lead to undesired conditions, such as pulp overflowing flotation cells (with insignificant/absent froth, and thus no valuable mineral concentration). Early detection and appropriate intervention of pulping events improves concentrator performance. An approach to real time flotation pulping event detection by means of convolutional neural networks is presented, including a case study of the industrial application of this technology on three flotation banks.

Feb 22, 2026

By William A. Riggs

Salt, a non-metallic mineral whose use dates back to earliest history of mankind, and whose uses cover the widest range for any mineral raw material, is generally of widespread occurrence in commercially recoverable quantities in the oceans, in certain sedimentary rocks, in certain lakes, and in certain underground waters. Passing over geological detail, it may be said that, generally, all of the salt in the world has, at least once in geological history, been in solution in the oceans. The total salt content of today's oceans, said to equal 4.5 million cubic miles of rock salt, dwarfs the tremendous volume of salt in the sedimentary rocks. In 1958, United States production of salt was about 22 million net tons and world production about 82 million. About 3 percent of United States production is table salt, with chemical, municipal, industrial and agricultural uses taking the remainder. Mississippi River. Figure 1 has been expanded sufficiently to show also those salt occurrences and producing points which might economically ship salt into these states. Although widespread in occurrence, salt deposits and possible production areas generally show very sharp local boundaries. Salt-for non-table use is susceptible to ?place value?, a common problem in low valued raw materials, where transportation costs often exceed the value of the material f.o.b. the production point. Generally only large capacity mechanized salt producing operations can compete in United States markets, as contrasted to the many small local salt evaporators in less industrialized Mexico.

Jan 1, 1962

By D. A. Shock

Utilizing the technology developed for oil well stimulation by hydrofracing, a disposal system which permanently fixes the waste has been proven. Large quantities of radioactive waste can be processed by a single well system making this method an attractive method for permanent radioactive waste disposal. The system depends on locating a relatively thick formation of impermeable, but easily fracturable rock such as a shale, creating a horizontal fracture, pumping the waste into the fracture in a form which will subsequently solidify and seal the fracture from the well system. The paper presents the theoretical considerations from creating and extending horizontal fractures and how these considerations were used in designing a waste disposal system which is now operating.

Jan 1, 1964

By E. Baliktsis

We have searched and analyzed several modern technologies aiming at the best applications of environmental management, the studying of quarrying ? mining as well as the excavation sites ? utilization ? rehabilitation. We have used long-range reflectorless laser surveying systems, so as to achieve the fastest and most accurate surveying of the extractive work sites. We also used them, in order to collect field data, measure distances, surveying monitoring stations and environmental parameters ? data. Furthermore these systems can make the field work quite faster, more reliable and credible and have low cost in collecting data even in dangerous and non-approachable areas. We have used and processed on the field data in G.I.S. applications, in order to create 2-D and 3-D digital ground models. These G.I.S. applications present the existing relief and the management of the final stage of the area. The suggested techniques and works needed, for reclamation and utilization of the areas, could be tried, evaluated and well presented. The evolution and utilization of these ?smart? modern tools for the effective environmental management of quarrying ? mining ? extractive activity sites, will be presented by using case histories from the Hellenic territory.

Jan 1, 2002

By Matthew Grzelak, Gulsah Erinc, David R. Chapman

"The third phase of the Bagram Drainage System project at Bagram Air Force Base in Afghanistan included construction of a shallow, 540-m long, 1.8-m inside diameter drainage tunnel. The tunnel penetrated mostly stiff to hard clayey and silty soils. The contractor’s Value Engineering Change Proposal (VECP) to use pipe-jacking with a microtunnel boring machine (MTBM) instead of the specified two-pass Earth Pressure Balance method was evaluated and supported using hand calculations. Contractor support was provided throughout the project by providing design reviews and instrumentation monitoring during construction. This paper compares the value-engineering proposal to the specified method and describes the construction conditions encountered. INTRODUCTION As part of a larger improvement project at the Bagram Air Force Base in Afghanistan, a shallow, 540-m long, 1.8-m inside diameter drainage tunnel was constructed to provide additional capacity for Coyote Creek to pass below several critical structures, including taxiways and the main runway, for mitigation of recurring flooding (see Figures 1 and 2). Overburden over the tunnel crown ranged from about 3 m to 5.5 m. An existing cast-in-place twin barrel concrete culvert runs approximately parallel to the new tunnel and is within about 8 m at its closest point. The contractor’s Value Engineering Change Proposal (VECP) to the specified two-pass Earth Pressure Balance (EPB) method (steel ribs and lagging or steel liner plate with a carrier pipe later grouted in-place) called for installation of the required drainage pipe by pipe-jacking (one-pass installation) using a slurry microtunnel boring machine (MTBM). The critical nature of the operations at the air base resulted in significant construction coordination challenges and a greater than usual need to avoid excessive settlements. Substantial restrictions were placed on drilling of investigative borings and installing instrumentation near runways and taxiways due to drill mast height. The prime contractor was SERKA TAAHHUT INSAAT A. S. (SERKA), the microtunneling subcontractor was Ludwig Pfeiffer Microtunnel GmbH & Co.KG (Pfeiffer), the jacking pipe designer was Gollwitzer Pipe and Shaft Technology GmbH (Gollwitzer), and the contractor’s tunnel engineer was Lachel & Associates, Inc. (Lachel). Lachel provided contractor support throughout the project including preparation of a VECP/Design Summary (including interpretation of existing and new geotechnical information), design reviews for jacking pipe, estimating settlement of an existing drainage structure above the new tunnel, and instrumentation planning, monitoring, and analysis during construction."

Jan 1, 2016

By Oliver W. Marsden, John O. Marsden

This paper presents the results of a hypothetical case study that evaluates the potential transition of a large copper mining and extraction operation to 90% renewable energy. The case study considers three phases to accomplish such a transition; phase I considers installation of renewable power generation at the site to meet a portion of the current electric power needs, phase II considers conversion of diesel combustion mining equipment to electric equipment, and phase III considers implementation of renewable energy generation coupled with energy storage systems to provide approximately 90% of the total mine site energy requirements. The paper evaluates the results in the context of a range of purchased electric power unit costs ($0.065, $0.100, and $0.135/kWh) as well as various carbon tax scenarios ($0, $5.00, and $37.30/t CO2). While the case study is hypothetical and considers a range of assumptions, it clearly identifies a pathway to potentially economically viable transitions to a renewable energy platform for mining companies. This represents an approach that mining companies can use to help to meet emissions targets, as well as social responsibility and reporting requirements.

Jun 4, 2021

By W. R. Reed, G. W. Luxbacher

Mine worker exposure to respirable coal dust and silica dust can result in coal workers’ pneumoconiosis and silicosis which are occupational respiratory diseases that have no cure and are ultimately fatal. In 2021 the Mine Safety and Health Administration reported just over 11,000 operating metal/nonmetal mines with the potential for silica dust exposure for just under 200,000 miners. The National Institute for Occupational Safety and Health (NIOSH) conducts respirable coal and silica dust research associated with mining through its Office of Mine Safety and Health Research. NIOSH respirable coal and silica dust research began under the U.S. Bureau of Mines (USBM), which initially examined silica dust, progressing to include coal dust, with a stronger focus after 1969 with the passage of the Federal Coal Mine Health and Safety Act. A review of extramural research to develop real-time respirable silica dust monitor is presented along with a brief history of silica dust regulation.

Feb 1, 2024

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By E. B. Graves

I have been asked to talk to you this morning about phosphate marketing and distribution. In discussing this I will attempt to answer such questions as: What is phosphate? Where do we get it? What form is it and how do we sell it? How do we distribute it? How is it applied? And last, but not least, What about the future? To start with, phosphate is one of the three primary plant nutrients. It is the element essential for root structure of plants. Plants, like humans, need a balanced diet. Thus, the amount of phosphate required by individual plants is, in part, related to how much of the other nutrients are used. Virtually all soils contain a certain amount of available phosphates. Back at the turn of the century the most common source of additional plant nutrient, including phosphates, was from cattle manure. The use of chemical fertilizers is something that has grown significantly during the last half century, and in particular, the last 20 years.

Jan 1, 1977

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open-pit and underground mines of all sizes are regularly collecting point cloud data as laser scanning (LiDAR) and photogrammetry surveying devices have become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely and safely, rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing. This article specifically focuses on digital outcrop modeling and digital terrain engineering. Point clouds. The high-resolution and increasing availability of point cloud technology is rapidly improving open-pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations and typically the reflective intensity and/or the visible three-band color of each point (Fig. 1).LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device.Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles and even in a mobile backpack shown in Fig. 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds,” but this article does not address these due to their higher cost and lower versatility and mobility."

May 1, 2016

By Serdar Aktaş, Burcu Nilgün Çetiner

According to critical statistical studies, antimony is one of the rarest elements in the world, and global resources could be exhausted by 2050. In light of these observations, its extraction will be costly due to poor-quality ore, deep mining, remote locations, and high energy consumption. In the present study, an alkaline leaching process was carried out on stibnite concentrate to evaluate the effect of reaction parameters on the percentage of antimony extraction. The leaching efficiencies of different sulfur and hydroxide sources were studied and compared to one another to create a better understanding of the reaction process. Kinetic models were investigated to identify the reaction pathway and calculate the activation energy. The activation energy of the stibnite dissolution was assessed as 19.13 kJ/mol using a two-dimensional diffusion-reaction model. The value of activation energy indicates the quantity of energy necessary for a reaction to proceed. As expected, potassium hydroxide leaching was significantly more successful than was sodium hydroxide; however, in terms of economics, the use of sodium hydroxide was found to be more cost-efficient. Interestingly, this finding indicated that caustic leaching is still the most effective method for stibnite extraction.

Jul 23, 2020

By Trevor R. Ellis

In August 2011, the Southern African Institute of Mining and Metallurgy (SAIMM) contacted mining institutes and related societies internationally to assess their interest in participating in coordination of the review of the South African Code for Mineral Valuation (SAMVAL) with reviews of other mineral valuation standards. The main mineral valuation standards are the CIMVal Standard of The Canadian Institute of Mining, Metallurgy and Petroleum (CIM), the VALMIN Code of The Australasian Institute of Mining and Metallurgy (AusIMM), the SAMVAL Code, and the extractive industries? guidance note of the International Valuation Standards Council (IVSC), Valuation of Properties in the Extractive Industries, GN 14, designed for application within the full set of International Valuation Standards (IVSs). By January 2012, SAIMM had concluded that the level of respondent interest was adequate to organize a meeting. A meeting was scheduled for April 18, 2012 in Brisbane, Australia in conjunction with a VALMIN mineral valuation conference organized by the AusIMM. The stated purpose of the meeting was to develop an accord on terms of reference for pursuing harmonization of mineral asset valuation standards adopted by the participating mineral institutes. SME decided that, although it has not developed its own mineral valuation standard, it should participate in the Brisbane meeting and the harmonization process, as also did the American Institute of Minerals Appraisers (AIMA).

Jan 1, 2012

By Shailendra Chawla, Ashok Jaiswal, B. K. Shrivastva

The study aims to evaluate the pillar behavior during the depillaring operation by continuous miner (CM) technology. A panel with five headings developed as per the coal mine regulation of Indian coal mines [2] has been selected for the study. The depillaring operation has been carried out using CM technology after widening and heightening the original entries. An extensive field investigation has been carried out throughout the depillaring operation to access the mining conditions. Depillaring operation has been performed smoothly up to the middle of the panel (fourth row out of eight rows of four pillars each). Advanced blinking of the auto warning tell-tale (AWTT ) has also been observed on some of the instruments during the splitting of pillar no. 18. The panel shows extremely difficult mining conditions at this stage. The case has been numerically simulated using three-dimensional numerical techniques. The simulation result has indicated the high stress and yield condition on the working and the barrier pillar (surrounding goaf from both sides) after the extraction of pillar no. 18. The analysis has also indicated the marginal stability of the 2nd barrier pillar (namely “pillar B”). The failure of the barrier pillar could be the responsible for global instability of the panel as observed in the field. Understanding the importance of the barrier pillars, panel design has been modified by incorporating an additional row of barrier pillars. The stability of the modified panel has been evaluated. Both working and barrier pillars have been observed stable in the modified panel. This could be an alternative layout considering safety at the working face.

May 8, 2022

In 2011, the value of mineral production increased in the United States for the second consecutive year (Table 1). Production increased modestly for most mineral commodities mined in the United States, and price increases, especially for precious metals, resulted in increases in the value of production. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates. U.S. apparent mineral consumption (industrial) of 11 mineral commodities decreased substantially from 2005 to 2010 (aluminum, cadmium, cement, copper, iron, lead, salt, soda ash, steel, tin and zinc). Data for 2011 were not calculated, but the data show a sustained decrease (especially for the metals) preceding the recession through 2010, so consumption seems to be behaving differently than production and GDP. After continued decline following the 2008?2009 recession, the construction industry began to show signs of improvement during 2011, with increased production and consumption of cement, construction sand and gravel, and gypsum ? mineral commodities that are used almost exclusively in construction. Crushed stone production, however, continued to decline.

Jan 1, 2012

By Scott Rosenthal, Dave Gilkey, Theresa Stack, Daniel Autenrieth, Ciara Kremer

Jackleg drill operators are exposed to harmful levels of hand-arm vibration (HAV). Anti-vibration handles and gloves provide modest reductions in HAV exposures and forearm muscle exertion from the use of anti-vibration handles and gloves by jackleg drill operators. The goal of this pilot study was to investigate changes in HAV with the use of anti-vibration gloves and handles compared to forearm muscle exertion experienced by operators and measured with surface electromyography (EMG). Five subjects operated the drill under four different cases: no anti-vibration controls, anti-vibration gloves only, anti-vibration handle only, and simultaneous anti-vibration handle and glove use. Muscle exertion was expressed as a percent of maximum voluntary contraction (%MVC) and was compared using Welch’s ANOVA with Games-Howell post hoc comparisons. The case with both anti-vibration controls in use simultaneously (largest grip diameter) was associated with a mean %MVC of 36.13% during operation for all forearm muscles combined, which was significantly higher than that of the other cases (p < 0.05). There were no statistically significant differences in mean HAV exposures. The anti-vibration handle with anti-vibration glove case only increased the maximum allowable exposure time by 8 min as compared to the control case without any anti-vibration controls. These results suggest that the modest HAV exposure reductions from the use of anti-vibration handles and gloves may pale in comparison to the increased muscle exertion resulting from their use, and this trade-off among jackleg drill operators is a potential concern that warrants further investigation.

Jul 12, 2021