Search Documents

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By C. L. Emery

The geology and early history of the discovery of potash in Saskatchewan as described by Heber Cole (1) and R. V. Thompkins (2) has dealt with the distribution of the salt beds and their potash content. From the many bore holes through the Prairie Evaporites the outlines and contours of the series have been well established. The thickest section of the salt beds lies to the north of the "barren" area and forms a belt running easterly to a point west of Yorkton. The "barren" area is a region where the salt has been redissolved and the strata have slumped down, to fill the voids. This area is of interest from the standpoint of rock mechanics. The potash-rich beds extend both east and west of the region. mentioned and the top of the Prairie Evaporite is at a depth below 3200 feet from the surface near Saskatoon and dips southerly at an average rate of about five feet to ten feet per mile.

Jan 1, 1966

By R. J. Roman

The results of column leaching tests on 3 different mixed oxide/sulfide ores from a Chilean deposit are presented. The 3 samples contained different ratios of oxide copper minerals to chalcocite and chalcopyrite. The results of the column leach tests are interpreted in light of the shrinking core model for coarse particle leaching. The copper recovery from the oxide minerals and the sulfide minerals each conforms to the shrinking core model with the total recovery equal to the weighted average of the individual minerals. The use of column test results to predict field heap leaching results using the multi-mineral shrinking core model is discussed.

Jan 1, 1993

By O. D. Staman

The risk assessment project examines the likelihood of inorganic contaminants from copper dump-leaching operations to contaminate domestic water supplies. The project examines contaminant transport by modeling contaminant movement from the base of a leach pile through the unsaturated zone and into the saturated zone. The modeling effort is unique in that it models infiltration, contaminant transport in the unsaturated and saturated zone combined with geochemical modeling of the unsaturated zone. The project incorporates probability theory to reflect the uncertainty of hydrogeologic parameters.

Jan 1, 1994

By D. H. Y. Tang

3-dimensional finite element modeling was performed to analyze the safety factors of stump pillars, 18 ft. x 18 ft., under a cover of 208 ft. using the Modified Drucker-Prager Theory. The results showed that they are safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and anlyze the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987

By Malcolm J. A. Swallow

In June 1997, Mount Polley Mining Corp., a division of Imperial Metals Corp., completed an 18-kt/d (20,000 stpd) gold-copper mine in central British Columbia. Fast-track construction and extensive off-site construction were combined with an aggressive project schedule to build the mine in one year. This was three months ahead of schedule and 7% below the original budgeted cost of C$123.5 million (US$86 million). The Mount Polley Mine was the first of a crop of new open-pit mines in British Columbia. The Mount Polley deposit has been explored since the mid-1960s when it was known as the Cariboo Bell property. From 1988, Imperial Metals completed drilling and metallurgical testing on the deposit. This led to a positive feasibility study and the issuing of a Mine Development Certificate in 1991. The project was later shelved due to falling metals prices and the strength of the Canadian dollar. In late 1994, Imperial merged with Bethlehem Resources Corp., bringing a strong project team to the company. The deposit was then re-evaluated, ore reserves revised and additional metallurgical testing was performed. The result was a revised project plan. It indi¬cated that a financially feasible gold-copper mining op¬eration could be constructed at Mount Polley operat¬ing at 18 kt/d (20,000 stpd). In May 1996, an agreement was reached with Sumitomo to jointly fund and develop the project. By early 1996, final plans and permits were being prepared for construction, scheduled to begin in June 1.996. On-site work commenced on May 28th, 1996 following lifting of the road restrictions. Mount Polley Mining acted as its own project manager. Construction was completed in June 1997. Plant runup took place in July and full production began in August. Through the use of off-site construction and the careful selection of contractors who cooperated to complete some 12 major contracts, it was possible to reduce the mine and mill construction time from 16 to 13 months. Off-site construction for all possible aspects of the work and the use of used milling equipment allowed significant savings in overall capital costs of construction. Total costs for the mine, mill and tailings dam equated to C$6,100/t/d of throughput. The mill design incorporates several innovative features that will aid maintenance and allow flexibility of operation. The operation is designed as a closed system and meets the latest environmental standards. Concentrate is shipped by truck to the port of Vancouver. Revenues for the mine come from the mine's production of about 3.1 t/a (100,000 oz/year) of gold and 10.8 kt/a (24 million lbs/year) of copper during the first four years of the 12-year mine life.

Jan 1, 1998

By S. A. McGhee

ASARCO Incorporated embarked on a modernization and expansion program to improve overall operating efficiencies and to more effectively develop the large mineral reserve at the Ray Complex Open-Pit Mining operation located near Kearny, Arizona. Major elements of this Ray Modernization and Concentrator Expansion Project included engineering and construction of a 54,400 MTPD (60,000 STPD) In-Pit Crusher and Overland Conveying System. and a 24,200 MTPD (30,000 STPD) Copper SAG Concentrator and Tailings Disposal System. Detailed engineering, procurement, and construction management were initiated in November 1989 under contract with Bechtel Corporation. Field construction commenced in May 1990 leading to mechanical completion and start-up during February 1992.

Jan 1, 1993

By L. Xu

Since the establishment of the standard dust concentration of 2 mg/m3, a strong effort has been made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines. Particular areas of success have been control of dust generation by better coal-cutting strategy, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomsky, 1983).

Jan 1, 1990

By W. R. Reed, J. P. Rider

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a medium-sized surface blasthole drill shroud with a dry dust collector system. CFD models were constructed in ANSYS FLUENT Version 15. Previously run experiments conducted in the NIOSH full-scale drill shroud laboratory were utilized to validate the models. The setup values in CFD models were calculated using experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for test scenarios, including 0.14 m3/s (300 cfm) bailing airflow with 2:1, 3:1, and 4:1 dust collector-to-bailing airflow ratios and 0.24 m3/s (500 cfm) bailing airflow cases with 2:1, 3:1 and 4:1 dust collector-to-bailing airflow ratios. For the 2:1 and 3:1 ratios, results showed the calculated dust concentrations from the CFD models were within the 95% confidence intervals of the lab experimental dust concentrations. This paper describes the methodology used to develop the CFD models, to calculate the model dust input, and to validate the models based on experimental data. Problem regions were identified and revealed by the simulation of a dry dust collector system. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. INTRODUCTION In surface mines, production drilling is an essential process in blasting which fractures the hard rock overburden for removal. Holes with a predetermined pattern, diameter, and depth are drilled into the overburden to introduce explosives. During the drilling process, considerable amounts of respirable dust are produced. Past research conducting area sampling at blasthole drills has documented time-weighted average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 [1] and 1.04 to 52.30 mg/m3 [2]. These high dust concentrations, which may contain silica, can lead to respirable dust over-exposures for the drill operator, drill helper, and other personnel in the vicinity. These over-exposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal. In order to prevent the development of silicosis to mine workers, the Mine Safety and Health Administration (MSHA) regulates the exposure to respirable dust. For metal/nonmetal (M/NM) mines, MSHA has adopted the threshold limit values recommended in 1973 by the American Conference of Governmental Industrial Hygienists (ACGIH) [3]. The total airborne dust standard is 10 mg/m3. However, if the sample contains greater than 1 percent quartz (the most common form of crystalline silica), a respirable dust standard is calculated with the following equation: Respirable dust standard = (10 mg/m3) / (% respirable quartz + 2)"

Jan 1, 2016

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2017

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By Indranil Roy

Gua supergene enriched iron ore deposit from Jharkhand, India has been geostatistically modeled. Population modeling shows a negatively skewed 3-parameter log-normal fit for Fe and positively skewed 3-parameter log-normal fit for Al2O3 and SO2. Semi-variographic studies for Fe indicate spherical function fit using point kriging cross-validation technique with Co=4.06(%)2, C5.11 (%)2, Co+C=9.1 7(%)2 and 'a'=348m. Kriging with 50mx50mx 10m block size at 740mRL led to a global mean kriged estimate of 61.98% and kriging variance of 4.04(%)2 for Fe with central 90% geostatistical confidence limits at 61.39% and 62.24% for that level. This led to an ore inventory at 740mRL as 7.29 million tonnes of ore.

Jan 1, 2002

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the National Institute for Occupational Safety and Health (NIOSH) developed a light-emitting diode (LED) area luminaire called the Saturn and conducted a laboratory study using a Fletcher High Dual-boom Mast Feed (HDDR) roof bolting machine. The Saturn luminaire was designed to (1) enhance floor illumination to enable better detection of trip hazards in the interior spaces of a roof bolter and (2) reduce glare that has typically been an issue of concern on roof bolters. This paper reports on the results of achieving the second objective. The existing roof bolter lighting was the baseline and was compared with three versions of the Saturn luminaire relative to light intensity (100%, 75%, and 50%). Discomfort and disability glare data were obtained from 30 participants that comprised three age groups. Discomfort glare perceptions were obtained using the De Boer rating scale, and disability glare was quantified by using Mars Letter Contrast Sensitivity tests. Discomfort glare was reduced at least 3 levels with all Saturn versions. Also, a predictive model was used to estimate discomfort glare, and the results were similar. Disability glare was the least for the Saturn’s 50% intensity, and all Saturn versions had significantly less disability glare than with the baseline lighting. Veiling luminance was calculated and used as another indicator of disability glare. Veiling luminance was 28 to 42 times greater with the baseline lighting as compared with that of the Saturn lighting. Lastly, visibility levels were calculated. The Saturn versions were 4 to 6.5 times better in terms of visibility level.

By Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources, and resistors. An analogous approach is outlined here for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The modeling technique proposed uses five basic (non-reducible) elements: the H element, the Q element, the D element, the R element, and the N element. These elements are characterized by their (a) pressure gain or loss, (b) air quantity, and (c) pressure-versus-quantity relationship, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine ventilation networks.

Jan 1, 1996

By Brendan Demich, Linda L. Chasko, Brendan Macdonald, Timothy J. Orr, Jessie J. Mechling, Cassandra Hoebbel, Jason Navoyski, William Helfrich, Jessica Cohen, Paul E. Schmidt, Jennica L. Bellanca

The National Institute for Occupational Safety and Health (NIOSH) in partnership with the Mine Safety and Health Administration (MSHA) developed VR Mine Rescue Training (VR-MRT). It is a training platform that allows mine rescue team members to explore virtual emergency scenarios collaboratively. Team members use a head-mounted display to visualize and interact together with equipment, hazards, and dynamic ventilation. All player actions are recorded and displayed for debriefing. Researchers at NIOSH demonstrated the training platform at various mine rescue competitions, including the International Mine Rescue Competition, and collected feedback. Participants’ responses were overwhelmingly positive. This paper describes the development of the software platform and the results of the usability surveys and interviews.

Jun 25, 2023

By J. Diao

In order to understand the flotation kinetic behavior of coal and associated mineral matter, a detailed investigation was conducted in a 2-liter Denver flotation cell using three high sulfur coals at three feed sizes, minus 28. 100 and 200 mesh. Subsequently. the flotation products were sieved into different size fractions and analyzed for their ash and pyritic sulfur content in order to delineate the effect of particle size on the rate at which each constituent floats. The results were tested with several different flotation kinetic models and the best model for coal was then chosen. The flotation rate constant and the ultimate recovery calculated from a kinetic model were used to delineate the effect of particle size, collector (dodecane) and frother (MIBC) dosages on the flotation kinetics of coal, ash and pyrite.

Jan 1, 1992

By J. Y. Lee, J. Kang

"A selective chlorination process using cuprous chloride (CuCl) was investigated for producing high-grade chalcocite (Cu2S) from chalcopyrite (CuFeS2) feed. The chalcopyrite feed was reacted with CuCl in the presence or absence of sulfur (S) at temperatures between 900 and 1,100 K for five hours under an argon gas atmosphere. The experimental results indicate that iron (Fe) was selectively removed from the chalcopyrite feed as ferrous chloride (FeCl2) at 1,100K and the mass percentage of Fe thus decreased from 31.5 percent in the feed to less than 0.05 percent in the residue, under certain conditions. As a result, high-grade Cu2S was obtained from chalcopyrite in a single step. This new selective chlorination of chalcopyrite using CuCl as a chlorinating agent is therefore feasible for producing high-grade Cu2S.IntroductionCurrently, blister copper (Cu) is commercially produced from sulfide ores by pyrometallurgical methods. These methods entail matte smelting and converting, with the removal of iron (Fe) and sulfur (S) as slag — mainly Fe2SiO4 — and sulfur dioxide (SO2) gas, respectively.In the pyrometallurgical method, as shown in Fig. 1 (Schlesinger et al., 2011), Fe is removed through two steps at high temperatures of around 1,500 K to reduce the loss of Cu during slag formation. However, the slag still contains 1 to 8 percent Cu. Therefore, Cu in the slag is recovered by slag treatment processes, after which the concentration of Cu in the slag decreases to around 0.4 to 1.3 percent. Although Cu is recovered, the slag that had undergone the treatment processes is difficult to use as a feedstock for ironmaking owing to the small amount of Cu remaining in the slag (Schlesinger et al., 2011).In addition, large amounts of SO2 gas are generated by the oxidation of S in the current Cu production process. The SO2 gas generated is captured and used to produce sulfuric acid (H2SO4). However, despite the development of SO2 gas-capture technologies, the emission of SO2 gas is still a problem in terms of environmental considerations.Several studies had been carried out in the past to overcome the drawbacks of the current process. The extraction of Cu from sulfide ores using a chlorination process is one alternative that had been investigated by several researchers. Most chlorination processes used chlorine gas (Cl2) as a chlorinating agent at temperatures between 573 and 1,023 K under an inert atmosphere (Donaldson and Kershner, 1962; Olsen et al., 1973; Kumar, Li and Warren, 1985, 1987; Kanari et al., 1999; Kanari, Gaballah and Allain, 2001)."

Jan 1, 2017

By Roger G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of Project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the Project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, developing geostatistical reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mecha¬nics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1983

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970