Search Documents

23.1-SOURCE, POWER-SYSTEM ELEMENTS A. J. T HUM Basic considerations in providing power for mine production and collateral operations are: 1. Mining operations of any size normally use electric motors for driving all equipment except mobile service units. 2. The electricity for power may be purchased or self-generated, depending on the location, size and specific operating circumstances of the individual property. 3. The major elements of the power system will be the source, either an incoming transmission line from a utility in the case of purchased power or the power plant if self-generated. Energy for the power plant may be water, hydrocarbon fuels, waste heat or nuclear, which will govern the type of prime mover selected. 4. The electricity normally is generated in the form of alternating current and must be distributed to the points of usage. This usually requires a primary substation for transformation to suitable voltages and secondary substations at points of usage throughout the operations, The power is delivered from the primary to the secondary substations over transmission lines or cables, depending on distances, voltages and local conditions. 5. At the points of use, there will be starting and protective devices for each motor. In some instances, direct current will be needed and rectifiers of various types can be used to provide it. 6. The entire electrical system requires suitable switching and protective devices to prevent damage to the equipment in case of power failues or faults; also, in most cases, sufficient metering to establish the demand and amount of electrical energy consumed. 23.2-PURCHASED POWER A. J. THULI 1. Where public-utility or government-generated power is available, it usually is advantageous for the mine owner to purchase rather than generate. Purchased power generally will be cheaper and more reliable than operating a small generating plant except in some cases where waste heat is available as the source of energy and can be used to supply all or a portion of the power requirements. 2. If it is decided to purchase power, the owner usually must participate in the cost of constructing the connecting line from the closest existing utility line to his point of usage. If the connected load is less than 1,000 lip, it probably is best to let the utility provide the primary substation. For larger connected loads the owner can obtain a more favorable "primary voltage" rate if he provides the primary substation to receive the incoming power and transform it to the distributing and usage voltages. 3. The cost of purchased power usually is made up of a demand charge, deter¬mined by the maximum amount of power the customer takes during any 15-min period throughout a month, and a graduated energy charge for the kilowatt-hours consumed-that is, so much for the first block of energy based on the demand,

Jan 1, 1973

By L. Yuan, A. C. Smith

MFIRE, the mine-fire simulation program of the U.S. National Institute for Occupational Safety and Health (NIOSH), is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines. MFIRE has been used by U.S. and international companies to simulate fires for planning and response purposes. It is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence, such as changes in ventilation parameters; external influences, such as changes in temperature; and internal influences, such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the former U.S. Bureau of Mines in the 1970s, several updates have been released. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated Fortran programming language was replaced with an object-oriented C++ language and packaged into a dynamic-link library. However, the MFIRE 3.0 release included no change or improvement to the fire-modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire-modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of the t-squared fire as a new fire-source model and the ability to include available heat-release-rate versus time data, the addition of a moving fire source for conveyor-belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke-rollback phenomena. All of the improvements discussed in this paper will be included in MFIRE 3.1 and released by NIOSH in the near future.

Jun 1, 2016

By H. J. Chen

In recent years, it has been recognized that the high horizontal stress is an important factor that contributes to a cutter roof. When the immediate roof is thinly bedded, the presence of a high horizontal stress may first cause failure on the bedding planes or weak planes, and then a cutter roof develops as the individual stratum crushes and buckles progressively layer by layer. In this study, the stress distributions in the bedding planes of the immediate roof are analyzed for an entry-pillar system in the multiple longwall panels by using the finite element method. Then the roof failure is analyzed based on the rock failure criterion and the stress distributions.

Jan 1, 1998

By G. Plenge, M. Diaz

Silver-bearing, bulk sulfide concentrates from several Peruvian mines were autoclaved in a l9-L (5gal) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates, following a hot lime jarosite destruction step, extracted more than 98% of the silver and more than 95% of the gold. Autoclave operating parameters, such as time, temperature, pulp density and autoclaved solids recycle, were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to provide reliable scale-up data for a 50 to 100 t/d (55 to 110 stpd) facility.

Jan 1, 1994

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific, and NIOSH have combined efforts to evaluate an in-situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an Aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was pre-loaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both real-time and time-weighted-average approaches. The real-time measurements were performed with the model AE33 Aethalometer® made by Magee Scientific. The results of the NIOSH 5040 method analysis were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82%-89%. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the Aethalometer were higher, possibly due to differences in the performance of the size-selectors used for the two methods (impactors versus cyclones). More research is required to develop a robust correlation between the two methods, to support the use of the Aethalometer for future mining applications. The advantage of the Aethalometer is that it can measure and record DPM levels for weeks at a time, and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in-situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise at reducing DPM concentrations in the mine environment.

Jan 1, 2016

By J. Sulaiman Lubis

Indonesia is a developing country in Southeast Asia with a population of some 180 million people. It has a stable political environment and currently enjoys high rates of economic growth. Indonesia has abundant reserves of natural resources, ample for its own needs and for export. Energy resources include oil, gas and coal. The oil and gas industries are well established domestically and for export. In the last few years, though, coal industry development has been rapid. Coal resources from bituminous to lignite amount to more than 30 Gt (33 billion st). That is more than enough to meet domestic needs and provide significant amounts for export. Figure 1 shows coal basins in Indonesia. Coals in Indonesia are generally young steaming coals. They are very low ash and sulfur, high volatile, bituminous B and C. The Indonesian government's state coal company is called Perum Tambang Batubara. The company has actively promoted the development of its coal for domestic and export markets. In particular, the government has placed priority on non-oil exports of which coal is a major element. The government strives to honor all contractural commitments for the export of Indonesian coal from contractor, private and government mines. From 1987 through 1989, coal production has increased from about 3 Mt (3.3 million st) to 9 Mt (9.9 million st). Exports have grown from I Mt (1.1 million st) to 3 Mt (3.3 million st). These are significant increases for a small industry with limited infrastructure. But with growing investment and development, these production and export levels will increase substantially, and Indonesia will be a significant world supplier of coal in the 1990s.

Jan 1, 1990

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By W. A. Hockings

This report describes a computer program for the solution of material balances in complex mineral processing flowsheets. The program, which is entitled MBS Metallurgical Balance System), evolved as the culmination of a series of material balance programs whose development began in 1967 at the Institute of Mineral Research, Michigan Technological University. The need for such a program became evident when the Institute became heavily involved in a large number of short-term pilot plant projects. Calculating material flows from analytical data by means of the standard two-product formulas grew increasingly difficult and time-consuming as the complexity of the flowsheets increased and as choices between conflicting analytical values had to be made. It was recognized that what was needed was a program that would assimilate all of the available data and calculate mass flow rates so that steady-state inputs and outputs would balance at each point in the flowsheet. Such a program should be capable of handling underdetermined, overdetermined and mixed systems, and when the given data are inconsistent, the program should adjust the data in such a manner that the adjustments are minimized. Missing analyses should also be calculated whenever possible. In addition to solving material balances, the program should be convenient to use and print out the results in a useful form. Thus, the inputting of data should be simple enough to be handled by relatively untrained personnel with diagnostic messages being printed out to identify errors and anamolous data when they occur. Most importantly, the program should produce well-formatted output which can be directly included into a report without the necessity of retyping. The proper spacing of table titles, column headings and the ability to control the columns being printed are important features in this respect.

Jan 1, 1977

Coal-derived flue gases contain CO2/SO2 and these contaminants preferably have to be captured by cheap sorbents. This remediation approach is from the standpoint of addressing issues such as global warming, acid rain and development of Advanced Power Generation Systems and to realize the economic gain as well. Conventional and existing dry scrubbing technologies use regenerable sorbents which are pollutant specific and require expensive stabilizers in order to attain versatility. This paper discusses the use a novel class of sorbents prepared from the heavy metal contaminated Berkeley Pit water (Butte, Montana) by a proprietary process developed at The University of Nevada, Reno. These sorbents are activated mixed spinel ferrite (MxFe,_X04)' Preliminary experimental results show that the sorbents have good desulfurization and CO2 decomposition capacities. The decomposition effectiveness of these mixed spinel ferrites was studied at 300°C and compared against the synthetic magnetite obtained from ferrous sulfate solution in our laboratory. The results indicated that the mixed spinel ferrite had good affinity for the adsorption and decomposition. The CO2 decomposition data of both sorbents fitted the first order reaction kinetics. Even though the surface area of the magnetite was higher than that of mixed spinel ferrite, the CO2 decomposition rate of the mixed spinel ferrite was estimated to be 2.5 times higher than that of magnetite under identical conditions. The carbon analysis deposited on the sample indicated that the CO2 was 100% decomposed into carbon and other carbon! hydrogen compounds by the mixed spinel ferrite whereas the conversion was 43% by the magnetite. In terms of specific adsorption of carbon, ferrite was 3-5 times more efficient than magnetite.

Jan 1, 1996

By Wolfgang Pietsch

DR iron') is a generic term for metallized product that results from the direct or solid state reduction of iron ore. In direct reduction, iron oxides are reduced to metallic iron in the solid state without an intermediate melting step. MIDREX ® Iron is the DR iron material produced in the MIDREX ® Direct Reduction Process. Except for some thermal and mechanical degradation, the external physical form of as-reduced DR iron is the same as the feed material. Chemically, oxygen associated with iron is removed leaving a very porous structure. Figure 1 is the scanning electron micrograph (SEM) of the internal surface of a MIDREX Iron pellet obtained from a Swedish oxide pellet during reduction at 760 °C. Figure 2 is the SEM of a polished and etched cross-section through the same pellet showing the amount of intraparticle porosity. As a result of this high porosity, apparent density of DR iron is relatively low, typically a¬round 2 g/cm3, and specific surface is extremely high, typically around 1.0 m2/g or more. Both density and specific surface depend on the raw materi¬al and the operating conditions of the direct reduction plant. Normally, more than 97% of the available iron is reduced into metallic iron with the rest mainly in the form of wustite (FeO). During direct reduction, the gangue in the iron remains essentially unchanged. Removal of oxygen and the corre¬sponding reduction in weight result in a slightly higher percentage gangue in the product than in the raw material.

Jan 1, 1976

By Neil D. Policow

Dewatering of the fine clean coal fraction, - 28 mesh (595 microns) represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the Screen Bowl Centrifuge has offered an economical alternative to filtration/thermal dryer combinations. The performance of Screen Bowl Centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Actual test comparisons with alternative methods show the Screen Bowl Centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1982

By F. Calizaya

A booster fan is an underground ventilation device installed in the main airstream to handle the total quantity of air circulated to one or more working districts. It is installed in a permanent stopping and equipped with airlock doors, a monitoring system and interlocking devices between the main fan and the booster fan. When adequately installed, a booster fan can be used to reduce the main fan pressure, reduce leakage and decrease the power consumption. However, an inadequate installation can increase the likelihood of mine fies and recirculation of air contaminants. This study identifies hazards associated with the operation and maintenance of booster fans. It analyzes the accompanying risks and recommends control measures to reduce those risks to acceptable levels. The ventilation network of an existing coal mine was updated to include a booster fan. The hazards associated with the operation of this fan were identified, the risks analyzed and the esponse to each failure mode established.

Mar 1, 2014

By Robin P. Gardner

The mechanistic approach to comminution consisting of incorporating particulate breakage functions into a suitable population balance equation has been developed by a number of researchers over the past decade or so. (1) To date this approach has been developed and demonstrated primarily for batch-operated, laboratory or small-scale ball mills. However, since industrial mills are mostly quite large and operated in the continuous mode; suitable population balance models and methods for obtaining the necessary breakage and other model parameters must be developed. This paper describes and investigates a radioisotope tracer technique for this purpose, Population balance models previously developed(2,3) are adapted for this study.

Jan 1, 1974

By Paul D. Tomlingson

An effective maintenance program ensures the adequate availability of production equipment. In turn, this availability enables production to maximize utilization and successfully meet production targets. An overall production strategy is necessary to draw all departments toward this common effort. Only then will production targets be met. From the maintenance view this means that production must comply with PM and repair schedules. Purchasing must supply parts and materials on time. Mine engineering must not overwhelm maintenance with non-vital construction. Accounting must provide correct, timely cost information - - etc. This strategy - - its content, effectiveness and enforcement is the responsibility of the mine manager . . . his alone. This paper describes a successful approach to maintenance within this strategy.

Jan 1, 1979

By Henry Rumfelt

Strip mining in the domestic coal industry is contributing a greater proportion of overall production than at any time in the past. U. S. Bureau of Mimes statistics show that the percentage of total production mined in 1958 by stripping methods in- creased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically, Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating over- burden and dumping it in the spoil position where it remains indefinitely). Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically, Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely).

Jan 1, 1960

By CASSANDRA L. HOEBBEL, PATRICK L. YORIO, Emily J. Haas

This study revealed significantly less favorable perceptions of the existing organizational safety climate among workers in the underground coal-mining sector compared with those in the industrial-minerals and sand, stone and gravel (SSG) sectors. Consequently, it is important to consider pragmatic ways in which health and safety management systems (HSMS) in coal mines can alter processes to improve these perceptions. Given the interdependencies of safety climate factors and HSMS elements, researchers explored mineworker perceptions of the supportiveness of organizational safety climate factors among mineworkers and identified significant differences in perceptions across sectors. In this paper, we suggest that health and safety professionals in underground coal mining and organizations with fewer resources or less mature HSMSs focus on these factors to bolster support for proactive safety performance. Potential barriers to implementing or improving relevant HSMS elements and ideas to help foster more favorable perceptions of organizational safety climate are also discussed.

By Thomas Hard

A description is given of a new facility processing blast furnace slag into a high quality cementitious material to be used as an ingredient in concrete for general construction purposes. A brief history of the process is given, followed by a detailed discussion of the water granulation system and the methods used to transport and dewater the granulate. Environmental advantages of handling slag away from the blast furnace by water granulation are included.

Jan 1, 1983

By J. A. Mielczarski

An infrared external reflection spectroscopy (ERS) technique has been developed to study the structure of the adsorbed layer of ethyl xanthate formed on copper and natural chalcocite (Cu2S) electrodes. The infrared technique provides information concerning the identity and the orientation of the adsorbed species at monolayer and submonolayer coverages. X-ray photoelectron spectroscopy (XPS) studies have also been conducted to monitor changes at the surface. The results show that the first oxidation peak on the voltammograms for copper and the first and second oxidation peaks on the voltammograms for chalcocite electrodes are not characteristic of a chemisorbed xanthate species, which is contrary to what has been reported by other investigators previously. As evidenced by the XPS spectra, there was an increase in sulfur relative to copper on the copper and chalcocite surfaces over the potential region where these oxidation processes occur. The spectroscopic results (ERS, XPS) indicate that the second and third (on copper) and the third and fourth (on chalcocite) oxidation processes recorded on the voltammograms are due to cuprous ethyl xanthate adsorption. The orientation of the adsorbed molecules of xanthate was observed to change with increasing surface coverage. Therefore, it has been concluded that xanthate can modify the copper and chalcocite surface in two different ways. At lower potentials, xanthate is a source of sulfur for the formation of a sulfur-rich surface. At higher potentials, an adsorption layer of cuprous ethyl xanthate is formed. Contact angle measurements show that both of these processes of xanthate surface modification lead to an increase in the hydrophobicity of the substrates.

Jan 1, 1990

By F. Seymour

A modified 3D Lerchs-Grossmann (LG) graph tree algorithm is presented that generates the complete set of nested maximum valued pits in a single run. This modified LG algorithm looks at the relative strength (average value) of the branches (groups of blocks). Pointers are allocated and pruned until there are no members of weaker (lower average value) branches overlying members of stronger (higher aver-age value) branches. The final set of strong branches are listed in order of decreasing strength. The pits they represent form the maximum valued convex hull for a single variable pit limit parameterization. A description of the algorithm is given along with examples of how it has been applied at Newmont.

Jan 1, 1995

By Ronald J. Vance

One of the key elements of change in the mining industry has been the ever-increasing integration and coordination of previously highly segregated business disciplines, the extent to which the marketing and finance functions have evolved and merged within the mining industry. If one listens to the language of mine product marketers today, one hears terms like contango, backwardation, forwards, options, min/max, synthetics, swaptions, caps, collars, FRA's, spot deferreds, double bottom, head and shoulders. The list is endless and a glossary may be out-of-date even before the ink is dry. No longer can a marketer of mine products get through the day and, more importantly, keep his or her job merely by reciting statistics on supply, demand, prices and the jargon of quotational periods, delivery and payment terms. Walk into the office of any marketing department today, and computer terminals spewing on-line market prices and instantaneous news retrieval command the attention of all who enter. Traditionally, mining companies, particularly those in North America, took a passive view toward marketing their products and an even more passive view toward management of price risk. The typical, albeit simplified, gold producer of the 1970s and early 1980s spent all of its energy exploring, delineating, developing and producing a product that was placed by the mine gate. Like magic, anonymous buyers took it away and left piles of dollars in its place. No fuss, no muss and nothing to get in the way of more exploring, delineating, producing etc. The typical copper producer, meanwhile, was slightly more creative. Copper producers still spent most of their energy exploring, producing etc., but they at least acknowledged the identity of their customers. Many even went so far as to fabricate finished mine products into shapes and sizes that their ultimate customer needed. Wire, cable, sheet and extrusions were all in forms ready to be purchased by power companies, motor manufacturers and telephone companies. But, while production and costs steadily increased, research and development into new expanding markets was funded by little more than lip service. Competitors and competitive products steadily eroded market share and realized prices. The now-famous Business Week magazine cover that proclaimed "The Death of Mining" was an imminent reality.

Jan 1, 1993