Search Documents

By Negar Elhami Khorasani, Anthony Tessari, Nan Hua

Fire hazards can cause severe and irrecoverable damage to reinforced concrete (RC) tunnel linings, threatening the serviceability and resilience of transportation networks. This paper first examines the existing methodologies that are used to classify damage to tunnel linings from fire. These approaches are then supplemented with the results of advanced modeling and inputs from industry experts to propose new fire damage/ repair classifications with the associated thresholds. The results of the presented research can be used to guide fire risk assessment as well as the performance-based design of tunnel fire protection.

Jun 13, 2023

By J. L. Sloughfy

The size distribution and mechanical strength of the iron ore pellet burden are important parameters in determining the efficiency of the blast furnace. From the very outset, the guiding principle of our pellet quality improvement program was that these parameters are also the key to improving productivity and cost control at the pellet plant. Recognizing the need for improved blast furnace burdens and for higher productivity and lower costs at the pellet plant, Carol Lake operators, in conjunction with the IOC Pellet Quality Committee, established the following goals for the improvement of Carol pellets: [ ]

Jan 1, 1981

By Andrew H. Merritt

INTRODUCTION The prediction of the engineering behavior of a rock mass depends upon the systematic analyses of the results of an exploration program, and upon the recognition of the significant rock properties in the early stages of excavation. The variations in rock properties in different geologic terrains and the state of the geotechnical art preclude complete success in the former case, and we therefore must rely heavily on the experience gained in the latter phase. The geotechnical information obtained from these two phases is only of value to the design engineer when applied to the rock behavior during excavation and subsequent plant operation. Pertinent questions which must be answered include: how does the joint orientation and frequency effect tunnel support and overall cavern stability; how does the depth of surficial soil or weathering effect foundations or slope stability for portal cuts; are there permeable zones within the rock mass that could lead to leakage problems around penstocks and is the material in these zones soluble or likely to pipe in the long term; and does the proposed engineering structure fit the terrain, or will it inevitably lead to problems requiring extensive remedial treatment. During the early stages of construction there are two types of geotechnical information required; actual rock behavior with respect to the original design assumptions,

Jan 1, 1997

By William Hodder, Lisa Smiley, Ehsan Alav

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km and be lined using a precast concrete segmental tunnel liner with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT liner was grouted through ports drilled in the segments. The Westerly Storage Tunnel (WST) in Cleveland will extend approximately 2.93 km long and will be lined by using a similar precast concrete segmental tunnel liner with an internal diameter of 7,620 mm and external diameter of 8,230 mm. The WST liner was grouted using both grout ports built into the tail can of the TBM and through segments. Each tunnel was mined primarily in shale with varying levels of weathering and both tunnels had dry and wet sections. This paper will document the means and methods for grouting in each tunnel as well as the methods utilized to proof grout and the results found.

Jun 13, 2021

By Robert L. Llewellyn

The Wharton No. 2 Mine of Eastern Gas and Fuel Associates is located about 60 miles south of Charleston, West Virginia in Boone County. Daily production is 6,000 T.P.D. on a two-shift basis. The Hernshaw Seam is mined by conventional equipment with one continuous miner in areas where conditions are suitable. The plant is on Cow Creek .Branch of Pond Fork, which in turn flows into the Little Coal River at Madison, West Virginia. When the mine was opened in 1948, plans were developed to build a dual Baum jig plant complete with mechanical and thermal drying, and because full production would not be reached for several years, it was decided to install only one Baum jig setup although the complete structure was erected. This phase of the plant was placed into operation early in 1949, The rated capacity was about 300 T.P.H. of 5" x 0 raw feed to the jig. Being a drift mine, the 10-ton mine cars are dumped at the Headhouse, crushed to 8" in a double roll crusher, conveyed 780 feet downhill to the picking .house where the +5" slate is removed by pickers. All coal is crushed to 5" and 5" x 0 is conveyed 150 feet to the cleaning plant. Further describing the plant growth, the second jig setup was installed in 1954 to clean the increased production. During this operating period, exhaustive tests had ,been run on the plant bleed which was an overflow from the large sludge tank located inside the plant, When the second jig addition was undertaken, 5-14' diameter and 12-8" diameter cyclones with a 9-disc filter were installed for the solids recovery and water clarification system, However, the circuit was not closed and a bleed of part of the overflows from the 8" diameter cyclones was still necessary, To comply with the State Water Commission regulations on stream pollution abatement, four pumps in series were installed to discharge the waste water behind the refuse pile.

Jan 1, 1959

By John W. Graham

To start my talk, I thought it might be helpful for us to define the term "aggregate", so I went to the dictionary. Webster has several listings under "aggregate", and I found the following: "1. A mass or body of units or parts somewhat loosely associated with one another." Well, I didn't like that term "loosely" so I read on. "2. Crystals of one or more kinds of mineral or rock fragments." That sounded better, but I still read on. "3. Any of several hard inert materials used for mixing with a cementing material to form concrete or mortar." That sounded even better, but it should be a little broader. So I would like to define "aggregates" for you as follows: "Hard, inert fragments of rock or minerals used alone or with cementing agents to form products essential to nearly all types of construction." Usually aggregates are sand, gravel, or crushed stone, but other minerals such as clay or shale can be heated and become aggregates. What are some of the construction uses? Well, we've already mentioned concrete, as used in streets and highways, sidewalks and parking lots, airports and all kinds of building construction, not to mention bridges and swimming pools, and docks and breakwaters, just to list some of the uses. Our way of life couldn't exist without concrete. And you can't have concrete without aggregates,

Jan 1, 1977

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By Yi Luo

Simulation of the multi-entry and multi-crosscut (MEMC) ventilation systems commonly employed in U .S. underground coal mines can be very tedious, due to the large number of crosscuts with stoppings to be represented in the network models. In order to reduce the amount of work needed to build the models, a common practice is to represent a number of crosscuts with one equivalent airway. However, this introduces certain errors into the simulation results. In this paper, algorithms have been proposed to simplify the ventilation networks of common MEMC systems encountered in panel development operations. The algorithms can be used to reduce a MEMC system into one airway with an equivalent resistance and to determine the airflow distributions in the system and the leakages through the stoppings.

Jan 1, 2011

By C. Y. Kao, Roger Y. Cheng, C. S. Hsieh

The mushroom-shaped Minghu power cavern located in central Taiwan is 21.2 m (W) by 40.5 m (H) by 127.2 m (L) and is designed to house 4 units of power generating-pumping equipment with a total capacity of 1,000 MW. This paper presents an introduction to the geological conditions at the cavern site; the rock mechanical tests undertaken; the design approach adopted; the construction method and sequence followed; and the instrumentation provided in the roof arch to monitor the behavior of the surrounding rocks. The measured data collected from the embedded instruments will be compared with those obtained from theoretical analyses and presented in this paper. Several technical problems encountered during the construction stage are covered and the solutions of these problems are also described therein.

Jan 1, 1983

By E. A. Domínguez

La Espingarda kaolin deposit was formed by ?in situ? alteration of volcaniclastic rhyolitic rocks belonging to Jurassic Marifil Formation. Three volcanic lithofacies were identified: porphyric biotitic ignimbrites (PBI), a coarse lithic ignimbrite (ILG), a fluidal intrusive rhyolite (RFI), all kaolinized in different degrees. The alteration covers an ellipsoidal area of ~20,000 m2, with its alteration decreasing downwards and disappearing at 8-12 m from the surface. The length to thickness ratio of alteration is 60:1. An erratic silicification was found as small zones (<3 m2) of quartz stockwork. The mineralogy is kaolinite + quartz + feldspars + Fe-oxyhydroxides ± halloysite ± illite and interstratified I/S, although the relative proportions change in each rock type. Due to coarse grain size and high quartz content, natural kaolin is unsuitable for slip cast ceramics, unless beneficiated. Washed ILG kaolin has the best rheological properties and behavior in casting and drying for its mineralogy, particle size distribution, thin texture and surface activity, as well as a certain fusibility and firing kinetics. PBI and RFI kaolins, due to finer texture, smaller grain size, lower surface activity, and higher halloysite amount, have worse slip viscosity and thixotropy that are due also to soluble salts. For the same reason, they have good casting and drying properties, but their purity brings about higher softening temperatures and water absorption. Several parameters are used to discriminate between hypogene or supergene kaolinite genesis. The hydrothermal genesis is mainly sustained by fluid inclusion temperature (150-180ºC) in quartz veinlets, while weathering is supported by deposit morphology, simple mineralogy, kaolinite stable isotopes (d18O ? 18, 13; dD ? ?59; ?85) and paleoclimatic record. It is concluded that a weathering process formed the main alteration with some participation of steam-heated meteoric waters. Neither the contents of Au, Ag, As, Sb, Hg, nor drill data support the existence of any epithermal gold mineralization at the kaolinite bottom.

Jan 1, 2010

By Robert T. Beckman

Education of inspection and operating personnel is essential to protection from radiation hazards in the mining industry. For over 10 years, MSHA has presented the only formal course on radiation measurements and control available to the mining community. Course objectives and content are described in this paper.

Jan 1, 1981

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

The main purpose of mine ventilation design is to provide sufficient quantity and quality of air to the workers and to dilute methane and other contaminants. It is generally perceived that the additional air along the longwall face will improve methane dilution on the face and in the tailgate. However, computational fluid dynamics (CFD) modeling efforts at the Colorado School of Mines (CSM) under a National Institute for Occupational Safety and Health (NIOSH) funded research project have found that higher flow velocities along the longwall face are shown to increase the pressure differential between the gob and longwall face allowing more methane to be entrained in the active face and tailgate (TG) area, thereby negating the dilution effect. The increased face ventilation causes an increase in pressure along the headgate side which allows more oxygen to ingress into the gob area, thereby increasing the amount of oxygen available to form explosive methane air mixtures in the gob and to support spontaneous combustion of the coal. Two things are happening at two different locations along the longwall face, increase in pressure as the flow enters the active area cause an increase in pressure which forces more oxygen into the gob, but as the flow is developed along the longwall face, the higher velocities causes greater pressure drop allowing methane to enter the active face further downstream from the headgate (HG) towards the tailgate side. In this paper, a parametric study will be presented to discuss the effect that varying the face air quantity has on methane concentrations in the tailgate and formation of explosive gas zones (EGZs) in the gob. Counter to conventional wisdom, it appears that increased longwall face air quantities may increase the explosion hazard as they result in increased EGZ volumes in the gob, along with increased methane quantities in the tailgate return.

Jan 1, 2015

By H. Braun, T. Kind, K. Gloe, D. B. Dreisinger, H. Stephan, O. Heitzsch, G. A. Kordosky

Municipal garbage incineration processes with coupled wet flue gas cleaning systems generate effluents containing toxic heavy metals such as mercury, zinc, cadmium and copper. The separation of these metal ions from the obtained scrubbing solutions is possible using liquid-liquid extraction. Extraction studies has been performed both with commercial extractants Aliquat 336, di(2-ethylhexyl) phosphoric acid and novel chelating agents as acyl thiourea and lipophilic oxathiaaza alkanes. Advantages and disadvantages of the investigated extraction systems are discussed. The paper reports on the basic research as well as on the testing in a laboratory scale.

Jan 1, 1993

By A. T. Yu

Two key components make up the core of a rapid excavation operation. They are: the breaking up of the rock and its removal. Owing to the complexity inherent in mechanical rock-breaking and the relative infancy of the art, for a number of years the first of these two components has received virtually undivided attention from the industry. Only recently has some concern been expressed about the technology and the economics of the much ignored second component: muck removal. As the continuous boring machine&apos;s percentage downtime continues to trend lower in the future, the need for adequate and more effective materials handling systems in rapid excavation will become increasingly more acute. (1) Recognition of the need for a broader and more far-sighted approach to our problem has been eloquently underscored in the conclusions of the Committee on Rapid Excavation sponsored by the National Research Council: "Ultimate attainment of the desired cost and speed improvements is significantly dependent on recognition of the excavation process as a system whose subsystems are critically inter-related. Substantial amounts of full-scale field testing of integrated driving, muck removal, and support subsystems are required." (2)

Jan 1, 1997

By A. K. Sheik, W. G. Pariseau

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine opening stability. Laboratory test data, borehole measurements and geological mapping assisted in constructing a coupled finite element model of the rock mass. The model was used to make quantitative estimates of: 1) rock stress, strain and displacement changes, and 2) water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. Stability of crown pillars between stopes was of particular interest. The relatively low effective stress and high rock mass strength showed that water pressure changes were of no great consequence in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific input data.

Jan 1, 1999

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

In this study, various rib bolting scenarios were investigated to better understand the effectiveness of the support systems. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid banded bright coal were considered. Different scenarios such as rib bolt length and number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength-reduction method in DEM code with the coal-mass model can aid in the development of practical primary sup- port charts, which can help in the rib support design process.

Feb 1, 2024

By Robert A. Irvine

Traditionally, cost effective gains in the capacity of material handling systems were a result of increases in equipment size. In general, the use of maximum capacity components in a system optimizes the production "costs per ton." The trend-"Bigger is Better" will continue in material handling equipment. Since it is rare for plant operators to lament an over abundance of screening capacity, one can safely predict that vibrating screens will follow this trend. Large Vibrating Screens - The Challenge Large vibrating screens represent a unique challenge for Manufacturers, Plant Designers, and Plant Operators. The inherent mode of operation for vibrating screens is self-destructive. More often than Manufacturers admit, Designers plan for, or Operators staff for, a vibrating screen succeeds and self-destructs. This is a problem. It can magnify with larger vibrating screens.

Jan 1, 1983

By John W. Stevenson

At the No. 4 Mine of Jim Walter Resources in Tuscaloosa County in the North Central part of the State of Alabama, the Mary Lee and Blue Creek coal beds lay 2000 feet below the surface. The quantity of methane gas stored within the coal bed reservoir at this depth and released during development mining necessitates that each coal producing section be ventilated using large air quantities approaching 100,000 cfm. In order to meet coal contractural commitments in the early stages of mine development by installing the necessary number of continuous mining machine units and to develop the mine to projected air shaft sites, high pressure, large volume mine ventilating fans were required. This presentation discusses the installation start-up and changeover procedures when two size GAF 31.5-28-1 TLT-Babcock 3500 Horsepower fans with adjustable pitch in flight blades were put on line while phasing out two Jeffrey Mining Machine Company 8HUA 117 Fans. A graph will be presented to depict the most economic diameter shaft size under 2000 feet of cover with different air quantity requirements.

Jan 1, 1982

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority&apos;s (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974