Search Documents

By Batric Pesic

Calcium silicate slag (Di-Cal) and magnesium oxide condensate (MgO) are the by-products of magnesium smelting operations, As these oxides have acid neutralizing and metal precipitating properties, it was decided to examine their reactions with (a) individual heavy metals and (b) with a mixture of metals in solution, The resulting solid reaction products were further tested with respect to the stability of the contained metals, The stability of the solid precipitates were examined as a function of the method of precipitation and as function of the solution pH With respect to the method of precipitation, the performance of Di-Cal and MgO was compared to the performance of lime, an industry standard for heavy metal precipitation, Four different pH solutions (4,0, 5,0, 7,0 and 1 LO) were used to study the effect of pH on the stability of the precipitates. It was found that Di-Cal, in most cases, produced the most stable precipitates and thus, outperformed lime, Metal precipitates prepared by the addition of MgO were the most soluble for each metal studied, except for Se,

Jan 1, 2001

By Huimin Lu, Liyuan Zhao, Zhijiang Gao

The aluminum matrix composite reinforced by graphene was successfully fabricated using high pressure torsion (HPT). With only 0.5wt% graphene, the grain size was reduced to 100nm while that of pure Al was about 500nm. The hardness of the composite increased from the center (64HV) to the edge (120HV) of the sample. Moreover, the tensile strength of this composite reached 197MPa, while that of pure Al was 157MPa. The enhancement in mechanical properties was induced by grain refinement, load transfer from the matrix to the reinforcement and dislocations piled up at the grain boundaries.

Jan 1, 2015

By C. M. Dentan

Conventional testing of crude kaolin ores emphasizes physical properties as they relate to end uses of kaolin products. This approach to evaluating crude ores does not reveal the basis of behavioral differences between typical coarse and fine kaolins from central Georgia. Optical and scanning electron microscopy in combination with XEDS have been employed to characterize both coarse Cretaceous and fine Tertiary kaolin in order to shed light on the reasons for the gross differences in their properties. Routine evaluation of various parameters was also carried out. Bulk densities were 1.48 g cc-l for the coarse clays and 1.53 g cc-1 for the fine clays. Surface areas were 15 m2 9-1 and 25 m2 9-1, respectively. Brookfield viscosities were low for the coarse clays at 70% solids, and high for the fine clays. The situation was reversed for Hercules viscosities. Sixty percent of the coarse clays had particles of less than 2 um and the fine clays had 90% less than 2 cm. Micrographs of thin sections prepared from blue-dyed epoxy-impregnated crude ores and of SEM fabric samples demonstrated vivid differences in texture. Cretaceous kaolins appeared to be completely recrystallized residual products of former aluminous sediments, while Tertiary kaolins retained their essentially sedimentary character. Differentiation of the coarse and fine kaolins is rapidly accomplished by both optical and scanning electron microscopy, and should be considered a valuable analytical technique in evaluating kaolin ores.

Jan 1, 1981

By Dan Wang, Yuanbo Zhang, Guihong Han, Guanghui Li, Tao Jiang, Yanfang Huang

"Hematite concentrates are characterized by bad high-temperature reactivity and poor balling index, which restrict their large-scale application in the production of oxidized pellets. An organic additive, namely MHA, was authorized and used as binder recently in China. Compared with bentonite, the effects of MHA on compressive strength of hematite pellets at various firing conditions were investigated in this study. Experimental results showed the compressive strengths of preheated pellets with different binders were increased with increasing the preheating temperature and time. The compressive strength of preheated pellets with MHA binder was lower than that of pellets with bentonite, which can be ascribed to the high porosity of pellets with MHA binder. However, the compressive strength of roasted pellets with MHA binder was higher than that of pellets with bentonite. The compressive strength of finished pellets balled with MHA binder 1.0 wt% could meet the operation requirements of grate-kiln process.IntroductionHematite concentrates are characterized by bad high-temperature reactivity and poor balling index, which can lead to the appearance of those problems with increasing the energy consumption, shortening the useful life of equipment, and finally increasing the operation cost of oxidized pellets plants [1-2]. Some investigations have been conducted based on improving the pelletizing technique of hematite concentrates, such as pretreatment of raw materials [3-7], optimization of ore proportioning [8], addition of solid fuels [9-16], and so on. Employing high pressure grinding roller for the treatment of hematite concentrates revealed that the mechanical strength of wet green pellets could be improved. However, the mechanical strength of fired pellets was not improved obviously [7]. Huang, et al., pointed out that the preheating and roasting temperature may be decreased and the compressive strength of fired pellets could be increased by blending a certain proportion of magnetite concentrates with hematite [8]. Nevertheless, there are a variety of magnetite ores different in physical and chemical properties in China, resulting in the instability operation [17]."

Jan 1, 2012

By Junfu Chen, Jiann-Yang Hwang, Yong Zhou, Lijun Lu, Likun Lia, Jixiong Liu

The sheet-like NiS-ZnS heterostructured composites were prepared by the microwave hydrothermal. The fabrication of the heterojunctions broadened the range of light response of ZnS. The photoexcited electrons of ZnS migrated to the redox potential of NiS/Ni2S under visible light irradiation, which can facilitate the effective separation of photogenerated electrons and holes in space. The visible photocatalytic activity towards hydrogen production for NiS/ZnS nanosheet heterostructed composites without co-catalyst achieved 0.28 mmol h–1, and the quantum efficiency was up to 18.6% under the wavelength with 420 nm visible light irradiation.

Jan 1, 2015

By A. V. Tarasov

Investigations of thermodynamic properties of Cu-Ni and Cu-Ni-S systems and mattes have been conducted with the aid of a MC-130 I mass-spectrometer designed for studies of processes of vapor formation of hardly volatile substances. The instrument comprised a combination of an evaporator of Knudsen chamber type with a mass-spectrometer for analysis of the vapor phase. In the process of studies of molten Cu-Ni-S systems and commercial-grade mattes within a temperature interval of 1400-1800 K the partial pressure of sulfur was measured by means of complete isothermal evaporation and the partial pressure of copper and nickel by comparison of ionic currents. The partial pressure values of the components above the molten Cu-Ni-S were used for calculation of activities of the respective components in the melt. The copper and nickel activity data obtained was used for assessing the amount of dissolved losses of these metals in autogenous smelting slags.

Jan 1, 2003

By Tae-Hyun Kim, Kang-In Rhee, Jeong-Soo Sohn

The synthesis of Mn-Zn ferrite powder from spent zinc-carbon batteries was investigated using a series of physical treatment, sulfuric acid leaching and coprecipitation. Physical separation methods such as crushing, magnetic separation and sieving were applied to generate a non-magnetic material of 8- mesh undersize for subsequent leaching process. The 8-mesh undersize of the spent zinc-carbon batteries was assayed 23.9% Mn, 14.9% Zn, and 4% Fe. Metal extractions obtained in sulfuric acid leaching at the solid/liquid ratio of 1:10, 2 M H2SO4, and 60? with 6 vol.% H2O2 addition were 97.9% Mn, 98.0% Zn and 55.2% Fe. The leach liquor was finally adjusted to the Mn:Zn:Fe mole ratio of 1:1:4 suitable for producing MnZnFe4O8 ferrite powder by the addition of Mn, Zn and Fe sulfates followed by pH control. A co-precipitation test for Mn-Zn ferrite powder was performed at 80?, O2 gas flowing at 1.3 L/min. As a result of co-precipitation, Mn-Zn ferrite nanoparticles in 20 nm size with spinel structure were successfully synthesized. The saturation magnetizations of Mn-Zn ferrite powder (Mn1-xZnxFe2O4) were determined to be 39-91 emu/g with various zinc contents (X=0.2-0.8).

Jan 1, 2008

By Keiji Toyabe

Several purifying techniques have been developed for controlling the impurity levels in the copper electrolyte at Niihama Copper Refinery. These have been carried out as follows; i ) the study of the reaction in liberation made it possible to raise the current efficiency for arsenic removal by more than 50% and to decrease generation of arsine sharply. By applying this method, a good performance was attained at commercial operation. li) the antimony in the electrolyte can be successfully removed by contacting it with activated carbon. This procedure is applicable particularly when there is a large amount of antimony in the copper anode. lli) for the nickel sulphate recovery from the electrolyte, an electric evaporating system was developed. The characteristics of this process are, capability of continuous operation with less manpower, the high recovery ratio of nickel sulphate (more than 85% as nickel) and no black acid formation in the treated solution.

Jan 1, 1987

By D. Pradhan, R. G. Reddy

"Electrorefining of aluminum scrap was investigated from AlCl3 –1-Ethyl-3-methyl-imidazolium chloride (EMIC) (Molar ratio 1.65) chloroaluminate electrolyte using copper cathodes at temperature of 90±3°C and cell voltage of 1.5 V. The deposits were characterized using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The study was focused to determine the effect of electrode surface modification as well as deposition time on dendritic depositions of aluminum. Their effect on current density was investigated also. It was shown that the surface modification of electrodes reduced the dendritic depositions of aluminum. Pure aluminum (>99%) was deposited for all experiments with the current efficiency of 94-97%. The use of ionic liquids not only reduced the energy consumption but also minimized pollutant emissions (CO, CO2 etc.) compared to the commercial high temperature aluminum production.1. IntroductionAluminum electrorefining/recycling from aluminum scrap using ionic liquid electrolyte is an attractive process today because of the unique chemical and physical properties such as wide temperature range for the liquid phase, high thermal stability, negligible vapor pressure, low melting point and wide electrochemical window. But in conventional practice, melting of aluminum scrap and high temperature molten salt electrolysis makes this process more expensive and less energy intensive (average 13 kWh/ kilogram of aluminum) [1] . Although recycling scrap aluminum requires only 5% of the energy used to make new aluminum [1-2], but the green house emissions like CO2, CO and HF have to be counted for environmental reason. Approximately, 5.31 kilogram of CO2 emitted per kilogram of aluminum production in most of the US industries."

Jan 1, 2009

By Åke Saudström

An EAF dust sample generated in a scrap based steel mill was treated by a combination of hydro- and pyrometallurgial techniques. The EAF dust contained mainly ferritic spinels forming solid solution phases according to the general chemical formula (MnxZnyFe1-x-y)Fe2O4 and other oxide phases such as ZuO. CaO and Ca2Fe2O5. The EAF dust was first treated by hydrochloric acid leaching at p8=3 which dissolved 63% of the zinc. The pyrometallurgical treatment of the leaching residue was studied using an induction heating system to simulate some important operations of EAF smelting of the residue in combination with steelmaking. The leaching residue was mixed with carbon powder to obtain a mixture with 52.1% ZnFe2O4 and 175% carbon. The mixture, scrap, and slag former were charged together in a crucible and heated to attain a melt temperature around 1650°C. The effects of different amounts of mixture on the zinc balance and iron recovery were examined. Based on the test results, suggestions are made for the EAF recycling procedure of the leaching residue.

Jan 1, 2003

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000

By G. Kyle Green

Zirconium chlorinator residues contain an array of rare earths, scandium, unreacted coke, and radioactive thorium and radium. Because of the radioactivity, the residues must be disposed in special waste containment facilities. As these sites become more congested, and with stricter environmental regulations, disposal of large volumes of wastes may become more difficult. To reduce the mass of disposed material, the U.S. Bureau of Mines (USBM) developed technology to recover rare earths, thorium and radium, and unreacted coke from these residues. This technology employs an HCl leach to solubilize over 99% of the scandium and thorium, and over 90% of the rare earths. The leach liquor is processed through several solvent extraction stages to selectively recover scandium, thorium, and rare earths. The leach residue is further leached with an organic acid to solubilize radium, thus allowing unreacted coke to be recycled to the chlorinator. The thorium and radium waste products, which comprise only 2.1% of the original residue mass, can then be sent to the radioactive waste facility.

Jan 1, 1995

By Yi Tan, Kazuki Morita, Yaqiong Li

Molten Si-Al alloy, with the addition of Sn, was used for metallurgical grade Si purification by a low-temperature solidification method, with the aim of improving the recovery rate of Si. In this ternary melt, bulk Si was grown with a planar front by a directional solidification process under a well-controlled thermal gradient and growth rate conditions, thereby reducing the contamination of solvent metals. Effects of cooling rate, amount of Sn addition, and temperature gradient on the quality of bulk Si were determined. The criterion for constitutional supercooling for single-phase growth from multicomponent melts was employed to evaluate the growth process.

Jan 1, 2015

By S. P. Rivers

The stainless steel industry re1ies on nitric-hydrofluoric acid (HNO,/HF) pickling solutions to remove surface contaminants and maintain the corrosion resistance of the steel. More stringent environmental guide1ines are expected to be placed on the disposal of these solutions which could significantly increase processing costs. The U.S. Bureau of Mines has been conducting research to develop a process for recycling depleted pickling solutions, thus reducing the quantity of by product acids generated. Research has shown that F- can be liberated from the predominant iron fluoride species (FeF,') by using oxalic acid in an electrodialysis cell. Ion selective membranes allow dissolved metals in the depleted solution to be replaced with hydronium ions by metathesis, thereby regenerating the HF. The regenerated HN03/HF is then retained in the pick1ing solution. This paper reports on the research effort at the U.S. Bureau of Mines Rolla Research Center to apply electrodialytic recycling to HN03/HF pickling solutions.

Jan 1, 1993

By Milance Mitovski, Milorad Cirkovic, Vlastimir Trujic, Dragana Živkovic

"In this article, it is analysed the possibilitis and the effects utility waste energy of process sulfuric acid production in the existing technical-technological conditions. The utility second process energy, reduction the fuels consumption, reduction environment pollution and its effects are shown, too. High heat quantity is produced as the result of exothermal reactions in the production process of sulfuric acid in Bor. A part of this heat is sufficient for the process development, and significant part of this heat presents low-temperature heat energy that is irretrievable lost. Investigations were carried out based on production of 485 t of monohydrate/day of sulfuric acid. By recovery of this heat quantity for heating purposes, about 20.000 – 25.000 t of coal/year would be saved, what would significantly improve the power efficiency of the smelter copper production. IntroductionTechnological process of copper production in RTB BOR (Serbia) produces a significant quantities of high temperature secondary (waste) heat energy that is uncontrolled “lost” in the vicinity. Secondary heat energy is produced in pyrometallurgical copper production in quantity of 1,621 kWth/kg of dry concentrate or existing heat (that presents a difference of heat at furnace outlet and heat at temperature over temperature of dew point of sulphuric acid gases) in quantity of 1,315 kWth/kg of dry concentrate. For designed capacity of Copper Smelter in Bor, the existing heat power of secondary energy is 92,111 MWt, what is an equivalent to the power of steam-turbo plant where the Rankine-Clausius heating cycle is done, and that is 28,334 MWe."

Jan 1, 2008

By Kurt Westerlund

Three. years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm /h at Boliden Ronnskar Sweden on a TBRC smelting palena (PbS). Operating experience from the Kivset flash WHB 11.900 nm /h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3 /h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By Jordan Mayorga, Joseph Kopp, Robert Boehm, Daniel P. Cook

"Solar generated power has long been considered a useful energy source only for low-energy density and non-mission critical use, such as providing electricity for residential applications. The success of Concentrating Solar Power (CSP) facilities, such as the 64 MW Nevada Solar- 1 near Las Vegas, have demonstrated that solar does have application to high energy density industries such as materials and chemical production. This paper will discuss the current operating con_guration of the Solar-1 facility and show how proposed modi_cations, such as addition of thermal storage and use of liquid salts as the working uid, can further improve the e_ciency and energy production of the plant.IntroductionThe United States as a nation is the largest consumer of energy in the world at an estimated 29 trillion kWh per year[1], which is roughly 15% of total global energy consumption[2]. On a per capita basis, the United States also leads most of the world, using an average of 96,000 kWh per person[3]. Roughly 40% of the energy consumed in the United States was produced from petroleum, 23% from coal, 23% from natural gas, 9% from nuclear and the remaining 5% from renewable sources such as solar, geothermal, wind, and hydroelectric[1].Energy demands associated with the industrial-scale production of chemicals and materials is a signicant portion of the United States total energy consumption. Roughly 33% of the energy consumed in the United States is used by the industrial sector, with 22% of this amount used in chemical production, 16% used in petroleum rening, and 14% used in the smelting and rening of metals[1]. Energy costs are also a signicant, if not the most signicant, portion of the total production costs for many materials. For example, roughly 30% of the cost of producing aluminum is the electricity used in the Hall-Heroult process [4], while the cost of energy is roughly 15% of the total cost of producing steel products [5].The primary sources of power for the industrial sector have been coal, petroleum, hydro- electric and nuclear. The use of alternative energy sources, e.g. solar, wind, geothermal, for industrial materials production has been slow in coming because they are intermittent and low-energy density sources, i.e. no solar power at night, no wind power when the air is still, etc. The success of Concentrating Solar Power (CSP) facilities, such as the 64 MW Nevada Solar-1 (NS-1) near Las Vegas, have demonstrated that solar can have application to high energy density industries such as materials and chemical production.This paper will discuss the current conguration of the NS-1 facility, and potential modications to the facility that will increase both its power e_ciency and power density."

Jan 1, 2010

By Lawrence L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P2O5 is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pet P2O5 and a P2O5 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1982

By H. A. F. de Souza, Dana S. Mills, P. E. Burgener

"ICP-MS has moved from a laboratory curiosity to a functional analytical tool. This paper discusses how ICP-MS has been used to solve difficult analytical problems encountered when analyzing various mine materials. Comparisons between analytical techniques applied to the analysis of gold and the platinum group metals illustrate the advantages and problems of ICPMS when. applied to trace levels of some metals iri the presence of ore grade metals. Interferences and matrix effects are compared to ICP, AA and Neutron Activation. The necessity to select chemical extractions which are compatible with ICP-MS are also discussed.The ICP-MS techniques explained in the examples on Au and precious group elements (PGE) have validity in analytical problems encountered in testing of trace metals in the presence of major elements found in mine materials. Exploration and environmental testing are other areas that require the same analytical approach to quantify trace levels in the presence of major interfering elements normally associated with mining environments."

Jan 1, 1999

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. The effects of feed matte grade, matte particle size, oxygen-to-matte mass ratio, oxygen content of the process gas and temperature on the particle oxidation rate, quality of conversion, particle size change and particle morphology were determined. The converting quality was highest (~68) with the 58% copper matte at 1100°C. At similar conditions, the 72% copper matte was more likely to produce copper oxides and leave unoxidized particles rather than directly produce sulfur dioxide at 1100°C, resulting in an average converting quality of 55. The quality of conversion was poorest for the 72% matte at 920°C (~45); the sulfur removal was extremely low even with a relatively high degree of oxidation. Fragmentation of the particles was significant in all cases with the 72% matte. A higher O2/matte .ratio and higher temperature, in general, resulted in increased fragmentation while oxygen enrichment had no significant effect. With the 58% matte, particle size was found to increase for the finest fractions rather than to decrease due to particle expansion.

Jan 1, 1998