Search Documents

By T. Kozuka, K. Sassa, S. Asai

"A new atomization process is developed. The principle of this process is completely different from that of conventional processes. This process uses electromagnetic energy induced by direct electric current and direct magnetic field instead of kinetic energy produced by fluid impingement or disk rotation.Experimental work of this process was carried out using pure tin, and it was found that the crucial factor for a stable operation is the contact state of molten metal with the electrode. In order to control the condition, a delay time controlling unit was developed and combined with this process. It is noticed that this controller works well to produce uniformly sized particles.A linear relation between the impulse and the momentum of atomized particles is found by use of experimental data and is explained by theoretical analysis.IntroductionIn atomization processes prevailing in metal powder technology, kinetic energy is currently employed for atomizing molten metal. That is, molten metal is broken into small particles by other fluid (e.g. water, argon gas, etc) or by impinged upon a rotating solid disk. This splashing process is always accompanied with uncertain factors for shape and size of the particles. The diameter distribution of products, therefore, comparatively spreads over a wide range. From another standpoint, the restriction of atmosphere is inevitable in some of these processes. As a pulverizing technology, the process which can produce uniformly sized particles and permits the choice of atmosphere is strongly desired.On the other hand, a great attention has been paid to the spray casting process as a new near net shape casting. In this process, a small size spraying device is favorable."

Jan 1, 1988

By Michael Altepeter

Big River Zinc Corporation, located in Sauget, Illinois, operates a neutral leach residue circuit. The residue produced in the circuit is sold to lead smelters for subsequent recovery of valuable metals. A research program was initiated several years ago to find a means of treating the residue at Big River Zinc to recover the valuable metals. The Ausmelt submerged lance reactor was selected as the best alternative for the first step of the process. Pilot scale tests were conducted at Ausmelt's facilities in Melbourne, Australia. Separations were excellent. 99%+ of the Zn, Pb, Cd, and Ag contained in the residue reported to the oxide fume. 99%+ of the SiO2,, Fe, Mg, and Ca in the residue reported to the slag which passed the EPA TCLP test. Subsequent leaching of the oxide fumes and purification of the leach solutions using conventional procedures produced solUtions suitable for zinc electrowinning and an upgraded lead sulfate cake for sale.

Jan 1, 1992

By R. Winand, M. Degrez, C. Temmerman

"The influence of the copper electro crystallization inhibitors (mainly thiourea, gelatin and chloride ions) is studied in a new fully automatic pilot plan. This paper describes the conception and the building of this plan. The new approach is to reproduce the experimental conditions observed in the industry with the three additives present simultaneously in the electrolyte and secondly to study the influence of a slight modification of the concentration of one inhibitor, the others being present in the electrolyte with their industrial nominalconcentrations.1. INTRODUCTIONDespite the fact that gelatine, thiourea and chloride ions have been used in copper electrorefining for a long time, precise knowledge concerning their influence on the cathode deposit, metallographic structure and associated properties is still lacking.Many authors studied the influence of each additive separately, or of two added at a time. Only a few authors studied the combined influence of the three additives added simultaneously. The general conclusion that can be drawn is that the combined influence is far from that forseen from the influence of each additive separately, or even from two additives used at a time. Moreover most of the experiments described in the literature were performed by adding all additives at once initially. It is however, well known that gelatine looses a great part of its activity during the first half hour due to degradation by sulfuric acid (as shown by the cathode overpotential drop). Thiourea is rapidly replaced by a number of degradation mole,cules and complex ions including cations from the solution, changing even the equilibrium between Cu, Cu(I) and Cu(II).Chloride ions are consumed by precipitation.A number of successive research projects [1-9] led pregressively to the concept that, in order to obtain reproducible results representative of industrial cathodes, it was necessary to simulate as far as possible industrial conditions. It was essential that all additives were added continuously during the electrolysis, with, as consequence, a continuous bleed.The purpose of this paper is to describe the concept of a new fully automatic pilot plan for copper electrorefining and to present the first results."

Jan 1, 1997

By M. Tamura, K. Fujita, K Shinozuka, H. Daimon, H. Esaka

"In-situ observation of unidirectional solidification using transparent substance has been performed to investigate the growth direction of solid phase. Cell or dendrite of which preferred growth direction is not parallel to the heat flow direction was observed with various solidification conditions. Dimensionless growth direction (p) changes from 0 to 1 with increasing growth velocity at a constant temperature gradient. Introducing the dimensionless growth velocity, the relation between p and growth condition could be correlated.IntroductionTransition in macroscopic solidified structure from chill to columnar zone which is found in normal castings takes place via grain selection1). Cast products such as turbine blades are unidirectionally solidified, grain selection plays an important role to choose suitable crystals which have reasonable orientation in the region called ""starter"", which is a very initial part of casting2). Therefore, grain selection is a very important process in the formation of casting structure. The present authors have been studying on the process of grain selection using succinonitrile, which is a transparent organic substance and have found that the growth distance necessary for grain selection depends upon the solidification condition3-5). When the solid/liquid interface is dendritic, the grain selection occurs quickly. On the other hand, when the solid/liquid interface is cellular, it occurs slowly. We supposed that the growth direction of dendrite is different from that of cell when the substance is unidirectionally solidified. Indeed, Kurz and Fisher wrote in their text book that dendrite grows along its preferred growth direction, <100>, regardless of heat flow direction and that cell grows along heat flow direction regardless of its preferred growth direction1). However, there is no quantitative description about the growth direction when the solid/liquid interfacial morphology is cellular. Furthermore, there have been little works6) to study the growth direction of cell and dendrite."

Jan 1, 2000

By Heimo Thalhammer

During the refining of lead, copper or other metals the furnaces used in the process · often produce waste gases. This paper illustrates how these waste gases can be successfully treated and destroyed by CTP 2-bed or multi-bed compact systems, modified for the additional reduction of dioxins and furans. The CTP regenerative thermal oxidizer also destroys voes (organic compounds and odours) using ceramic blocks as a heat exchanging media. The raw gas is forced through the ceramic beds where it is heated up to the oxidation temperature level. The voes, dioxins and furans are destroyed in the combustion chamber, subsequently generating water, eo2 and heat. The hot purified gas heats up a second ceramic bed, which is used to preheat the raw gas after the valves have been switched. This process does not produce any secondary waste such as contaminated water, polluted air or any other products that have to be disposed of.

Jan 1, 2000

By Demaerel. J. P.

Arsenic plays a major role during electroreflning of copper. Both the arsenic content in the anode and the arsenic concentration of the electrolyte have, in conjunction with other impurities such as lead, antimony, bismuth and oxygen, a direct influence on the quality of the cathode. The mechanisms are currently slime. inclusion and precipitation of insoluble compounds in the bulk of the electrolyte. Arsenic has also been reported to have a depassivating effect on the anode. An influence on the anode slime adhesion has also been found. A literature survey is given and these data are compared with and completed by our own results based on lab and pilot scale experiments as well as on Olen tank.house practice.

Jan 1, 1987

By K. Sanjay

Factorial optimisation technique has been used to develop regression equations at different time intervals for extraction of manganese from precipitated manganese oxide/hydroxide in sulphuric acid using charcoal as the reductant. The three parameters chosen for a 23 full factorial design were : acid concentration, amount of carbon and temperature. The regression equations were used to predict >> 90% extractions as well as kinetic data.

Jan 1, 1996

By Jing Zhan, Gui Li, Wei-feng Li, Li-Hua Jiang, Chuan-fu Zhang, Jian-yang Hwang

Thermodynamics analysis for processing the charge with lead concentrate and lead sulfate-containing materials in bottom blowing smelting furnace was conducted. The results show that the technology of large-scale processing PbSO4- containing materials with PbS concentrate in bottom blowing furnace under the condition of using high-iron slag type, batch heat supplement, high temperature and rich oxygen is thermodynamically feasible. The exploration test and industrial experiment confirm the results. When S content in mixed ore is 16~17% with coke foam content of about 5%, the lead paste amount can be increased up to 40%.

Jan 1, 2015

By D. R. Spink

A partial desulfurization roasting (PDR) technique has been developed for use on zinc concentrates whereby the sulfide sulfur associated with the iron content is selectively removed over a very short residence ?time in the roaster. The resulting PDR product is then leached for the selective removal of the iron. The resulting leach restdite is an upgraded zinc sulfide concentrate which has a very low iron content. The up-graded zinc concentrate can be subjected to a conventional dead roast without formation of deleterious zinc ferrite so that hot acid leaching and jarosite (or other) iron precipitation steps are obviated. Examples are presented for the treatment of three very different types of zinc concentrates.

Jan 1, 1990

By Jian Li, S. Penttila, W. Zheng

"Materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. Beside high-temperature mechanical properties, SCC and general corrosion resistance of commercially available materials are also major focuses in recent research. Recent reports suggest that certain types of surface modifications are beneficial to SCW corrosion resistance. In this study, the effects of surface modifications are investigated, and possible mechanisms for improved corrosion performance are discussed.IntroductionThe current Canadian pressure-tube supercritical water reactor (SCW) design specifies a core outlet temperature of 625°C under 25 MPa of pressure, with peak cladding temperature as high as 850°C. Challenges in materials selection include high-temperature mechanical properties, corrosion resistance, SCC resistance and radiation damage. Most of the SCW corrosion test results available are below 730°C. Early work by Allen [1] summarized the corrosion resistance of alloy groups including Ni-based super alloys, stainless and ferritic/matensitic (F/M) steels that can potentially be used for SCW reactors. F/M steels can only be used at low temperature sites (e.g. down stream piping). At 500°C and 25 MPa, F/M steels develop a thick but mechanically stable oxide layer. However, the long term stability of the surface oxide layer is largely unknown. Ni-based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of some intermetallic precipitates [2-5], and dissolution of major alloying components could pose significant problems for down stream piping [6]. In addition, concerns of Helium formation due to Ni transmutation prevented this alloy group to be used as fuel cladding. The corrosion resistant austenitic stainless steels (e.g. 316L) are found to be susceptible to localized corrosion such as pitting, intergranular attack and stress corrosion cracking (SCC) [7]."

Jan 1, 2012

By Kazuyoshi Sato, Keizo Uematsu, Nozomu Uchida

"Confocal fluorescence scanning laser microscope was applied to characterize the surface flaw of ceramics in great detail. A high potential -of the characterization technique is presented first. Then the technique was applied to clarify the relationship between the flexural strength of ceramics and the surface flaw. This kind of direct information of surface flaw should be essential for the fundamental study in this area, but has been lacking. The examination revealed that large defects are present on the machined surface of ceramics. Their size is consistent to the flexural strength measured on the material. The characterization tool was also applied to examine the formation of surface flaw in machining of ceramics.IntroductionClarification of fracture origin should be the starting point in the study on strength in ceramics. However, this task has been extremely difficult in some ceramics, such as an alumina ceramics. It may break from both internal and surface flaws. The former should reflect the quality of production process and the latter the machining. Examination of surface flaws should be very important for developing a better machining method for ceramics. The knowledge may valuable for establishing a better production process also.ExperimentAlumina Referceram (JFCC) was used as samples. They are cut to size of 3x4x40mm, and the surfaces were ground to meet the requirements of testing method for flexural strength of fine ceramics, JIS R 1601. They were soaked in an aqueous solution of fluorescence dye and evacuated with an aspirator for an hour to allow the solution penetrate into surface flaws. After excessive solution remained on the surface was removed by gentle washing, the specimens were dried at 120°C for 48 hours. The 4 point bending mode was applied to measure the fracture strength."

Jan 1, 2000

By Mario H. Castro-Cedeno

"A design for a handheld MEMS chemical detector is proposed. The detector will be used to detect trace amounts of chemicals in air. It can detect drugs, toxic chemicals and/or explosives. The proposed detector will use ion mobility spectrometry (IMS), a technique that is well known for accuracy and has been used in the past in suitcase sized chemical detectors. The separation and detection of the chemicals occurs in the drift channel and the process was modeled using the finite element method and CoventorWare modeling software. A manufacturing process sequence for the drift channel is proposed and was demonstrated.IntroductionThe goal of this effort is to design, mode~ and prototype a MEMS chip that will be the key component in an ion mobility spectrometer (IMS). This technique uses and asymmetric potential to separate the various ion species in a stream of incoming air [1-4]. One advantage of IMS is its ability to separate chemical species from air at atmospheric pressure and temperature. This is a requirement for a simple to use handheld drug or chemical detector. IMS can be used to detect drugs, toxic chemicals and explosives and it is well known for accuracy in detecting very small amounts of chemicals. This chemical detection technique has been used in the past, but not in handheld detectors.One variant of IMS is the high-field asymmetric waveform ion mobility spectrometry or FAIMS [3]. The FAIMS process, shown in Figure l, works as follows: a gas sample is admitted into the instrument where gas molecules are ionized, typically by a weak radioactive isotope source, ultraviolet light source; and more recently through field emission. The ions move along the length of a channel while they are separated in the transverse direction by an asymmetric electrical potential. The potential, in the form of an asymmetric waveform, causes relative motion between the various chemical species. The species that hit the charged top and bottom plates are neutralized and only those ions that move along the center are detectable as charged chemical ions at the end of the channel."

Jan 1, 2004

By D. T. Smith, L. M. Hsiung, J. J. Schmitt, J. W. Golz, R. L. Lankey, H. N. G. Wadley, J. Z. Zhang, B. L. Halpern

"The microstructure and mechanical properties of Al/AI2O 3 metal-oxide nanolaminates fabricated by' a novel Jet Vapor Deposition (JVD) process at substrate temperatures of ~25° and -250°C have been investigated using transmission electron microscopy (TEM) and nanoindentation methods. The thickness of the oxide layer was held constant between 2 and 5 nm, whilst the Al layer thickness was systematically varied from -3 to -50 nm. Continuity of the Al layers was significantly improved when the nanolaminates were deposited at an elevated substrate temperature (-250°C). The yield strength of the nanolamintes with Al layers greater than -25 nm follows a Hall-Petch type relationship, whereas that of the nanolaminates with Al layers less than -25 nm is better predicted by a Koehler-Lehoczky strengthening model. IntroductionAluminum-aluminum oxide (presumably A12O3) nanolaminates have been recently fabricated using a novel Jet Vapor Deposition (ND) process developed and patented by Jet Process Corporation [1-4]. ND uses sonic, high purity helium (He) gas jets to entrain atomically dispersed vapor and deposit films. It is of interest here because it can deposit multilayered structures (laminates) inexpensively at high rates. Materials with a thin, multilayer structure are of interest because they potentially offer novel mechanical and physical properties [5]. Koehler in 1970 used an image force model to investigate the strength of laminated materials and proposed the use of alternating layers of high and low shear modulus metals to produce high strength composite materials [6]. He predicted that dislocations would have to overcome a large repulsive image force in order to move from metal layer B of lower shear modulus (uB) into metal layer A of higher shear modulus (uA)' The image force (F) is given by the relation:"

Jan 1, 1994

By C. Lupi

Zinc impure solutions as spent electrolytes, leach liquors coming from aqueous treatment of both minerals and solid waste, need to be purified before undergoing the treatment to obtain the final product. Solvent extraction is one of the most selective operations particularly when many metallic ions are present in solution. Zinc pure solutions are frequently obtained using DZEHPA as extractant. In this work an investigation on zinc extraction effectiveness of naftenic acid was carried out. After determining the best diluent and the optimal extractant concentration, the partition coefficient was determined as a function of temperature, equilibrium pH and zinc concentration. Finally same batch tests to determine the equilibrium curves at room temperature on exhausted electrolyte coming from zinc cell were carried out by using naftenic acid, D2EHPA and TBP. The pH giving, for each extractant, the best extraction yield was selected in order to compare the equilibrium curves. Experimental results show that all the examined extractants are very effective in zinc extraction if the process conditions are appropriately selected. In order to avoid an impure solution pre- treatment and to obtain the maximum ertraction yield the appropriate solvent can be chosen.

Jan 1, 1998

By Darryl Lovato, Ramiro Pereyra, Daniel S. Schwartz

"During an annual inventory of nuclear material, a plated steel container which contained plutonium oxide failed. The container had been packaged for temporary storage but had been overlooked and remained in storage for more than 23 years. Although it was determined that the failure occurred through the slip-top rim, a metallurgical evaluation was requested to help to determine the integrity of the container.Optical metallography and scanning electron microscopy were used to analyze the character and degree of corrosion in the container. The depth of corrosion, measured at approximately 10 µm, did not pose a threat to the integrity of the container. However, the corrosion morphology and chemistry did suggest that a galvanic cell had developed between the tin and steel from the condensation of water. The morphology also suggests that the attack of the steel took place over a series of cycles due to changes of the environment.IntroductionMetallographic analysis was requested as part of the investigation into the mechanism of the failure of a slip-top container (#38621) containing plutonium oxide (PuO2) powder. The container had leaked during a special nuclear material (SNM) annual inventory causing contamination and closure of the vault. A photograph of the container and interior container is shown on the right in Figure 1. An initial investigation established that the source of contamination was the consequence of the failure of multiple layers of containment. Initially by the deterioration of the interior plastic bottle and polyvinyl chloride (PVC) bagout bag, and finally through the lid and steel container interface at a location where tape had not adhered properly [1]. Although the source of the breach was established, it was determined that metallographic analysis was important to establish the extent of deterioration of the steel container."

Jan 1, 2008

By Bora Derin, Sertac Yazici, M. Seref Sonmez

"In this study, the recycling conditions of waste liquor obtained after the production of tungsten boride powder from calcium tungstate by self-propagating high temperature synthesis (SHS) and the following hydrochloric acid leaching were investigated in detail. Environmentally unfriendly and extremely acidic (pH~ -0.3) liquor consisting of calcium, magnesium, and boron ions was treated with 1 M sodium carbonate solution to precipitate magnesium carbonate and calcium carbonate phases. The obtained amorphous precipitates were heated up to the temperature of 400°C for re-crystallization. As a result, MgO, CaC03 and CaMg(C03)z phases were obtained, while sodium, boron, chlorine ions were remain in the solution. The present study is still in progress.IntroductionSelf-propagating high temperature synthesis (SHS) is one of the techniques used in the production of a variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers [ 1, 2]. The reaction becomes selfsustaining and propagates in the reactant mixture, after initiation in SHS process. SHS products may contain the mixture of several unwanted compounds and elements. Therefore following acidic leaching process may be needed to purify the target product. In the previous study, calcium tungstate (Ca W04), magnesium (Mg) and boric acid (B20 3) mixture were reacted to produce tungsten boride powder by SHS process according to the Reaction 1. Then, magnesium and calcium containing byproducts (i.e. MgO, Mg3B206 and Ca3B206) found in the SHS product were leached out by using concentrated hydrochloric acid (HCl) solution to obtain pure tungsten boride powder [3].Ca W04 + 0.5B203 + 4.5Mg = WB + 4.5Mg0 + Cao (1)After the leaching, filtrate solution consisting of different amounts of magnesium, calcium, and boron requires additional treatment for the environmentally acceptable disposal.Several works were carried out about magnesium precipitation conditions and kinetics from brines. Rabadzhieva et al. investigated the precipitation of Mg(OH)z from brines by using NaOH as well as caustic soda [ 4]. Turek ve Gnot investigated the precipitation efficiency of Mg(OH)z for the temperature range between 10-40°C, while the reaction was kinetically experimented by Alamdiri et al [5, 6]. Homogeneous precipitation of nesquehonite (MgC03.3H20) by the reaction of MgCli with (NH4)2C03 in supersaturated solutions and factors that influence the precipitation of MgC03.3H20, such as reaction temperature, initial concentration, stirring speed, titration speed, equilibration time, have been studied by Wang et al [7]. The precipitation of Mg(OH)z by calcium hydroxide from aqueous solutions was studied by Baird et al. [8]. Stratful et al. focused on conditions influencing the precipitation of magnesium ammonium phosphate from wastewaters [9]. 1031"

Jan 1, 2011

By Shiwei Sun, Hongxu Li, Xiangxin Hao, Xie Yang

"Environmental impact assessment of copper metallurgical processes will soon become a compulsory activity in the future. The goal of this work is to analyses the copper metallurgical processes including pyro-metallurgy and hydrometallurgy based on the life cycle assessment method implemented in GaBi software. The evaluation indicators such as global warming potential (GWP), acidification potential (AP), photochemical ozone creation potential (POCP) and human toxic potential (HTP) are taken into account. The results show that the major environmental impact phase in pyro-metallurgy derives from beneficiation because of the largest material and energy consumption. It is also shown that copper hydrometallurgy has significantly lower environmental impact than pyro-metallurgy. Based on the evaluation results, some corresponding optimization methods are recommended to reduce environmental impact.IntroductionCopper is an important metal in modem society due to its wide variety of uses, including electrical wiring, heat exchangers, piping and roof construction and increasingly consumer electronics. Demand for copper has increased dramatically over the past decades, driving production rates almost exponentially. Annual production of copper was estimated to be 20 million tonnes in 2012 with Chinese production at about 6.06 million ton in 2012P1. The production process of copper has environment impacts that often go unnoticed by the producer. Higher production, coupled with declining ore grades, is placing increasing pressure on the natural environment.Sound environmental management helps producers improve their manufacturing technique. LCA is a well-established tool for assessing environmental impact potential and can be readily adapted to map impact potential over time, which can be used to quantify the environment impacts of a product or a process [21. This is achieved by creating an inventory of all the energy and material flows used in the process's life cycle. The results of an LCA can be used to improve the operation of a process so that they have less impact on the environment."

Jan 1, 2014

By Motoyasu Sato

Highly pure pig irons were produced in a multimode microwave reactor from powdered iron ores with carbon as a reducing agent in the nitrogen atmosphere. The grains in compacted powder absorb microwave energy selectively. Microwave-matter interaction creates thermal non-equilibrium state microscopically and enhances chemical reactions and the phase mixing at the grain boundaries very rapidly. The visible light spectroscopic techniques was used to monitor the progress of the reactions. Up to 650°C, the heated powders radiate the continuous spectrum of blackbody emission. The small non-equilibrium hot spots rise, move and finally burst in to brighter light emitting from all over the surface at 650°C. CN molecules and Fe (I) atoms were identified in the recorded spectrum. These bursts are similar to the ?ignition propagation? normally observed in chemical reactions. The line spectra originated from CO molecules have not been detected yet. The solid-solid reaction could be expected between the iron oxides and carbon to produce CO2 directly. A loss in the sample weight was accelerated during the excess-emission. These are the clear evidence that microwaves cause thermally non-equilibrium state and accelerate reduction process. The reduction of iron ore is completed at 1380°C and relatively very pure pig iron was produced. It should be noted that the impurity level of Mg, S, Si, P and Ti is only 5-10% of what is found in the pig irons produced by modern conventional blast furnaces in the steel industries. The necessary amount of carbon needed was 1/2 compared to conventional blast furnace to produce the unit weight of steel, if we applied renewable energy or nuclear power for the microwave excitations.

Jan 1, 2006

By J. M. Figueiredo, A. R. Silva, M. C. Coelho, R. M. Guedes

"With the continuous depletion of conventional sources of non ferrous metals, low grade complex sulphide deposits have been regarded as an alternative source of supply of zinc, copper, lead and also silver and gold. In spite of very important efforts in research in this domain it is still a long way to go in order to achieve reliable technological solutions both in ore dressing and metallurgical treatments which enable these complex materials to be regarded as commodities. The RLE process to treat bulk concentrates such as those obtained from portuguese ores, under development at LNETI and QUIMIGAL premises, combines experienced unit operations and innovative configurations and is an effective contribution for the future use of these materials. The results of three years of experimental work and main conclusions on the overall feasibility of the process are presented.IntroductionIn spite of the very well-known problems associated to the development of complex sulphide deposits, the economical importance of the enormous reserves of these materials, widespread all over the world, is so evident that its future use as source of supply of basic and precious metals and other minor elements is almost unavoidable.Critical steps in that direction are mainly concerned with favourable economical conditions and sound metallurgical practice for the treatment of nonferrous metals concentrates, which are nowadays still considered as non-conventional raw materials.Since Portugal is one of the countries where these orebodies occur more extensively, Portuguese authorities have dedicated since the beginning of the seventies, a big effort on finding economical and reliable processes for the recovery of copper, lead, zinc and also gold and silver, and for this purpose, several alternatives on ore dressing and metallurgical processing were studied, however without full sucess.Five years ago LNETI, a research laboratory, and QUIMIGAL, a chemical company, both state owned, decided to launch a research programme for the development of a metallurgical process for the treatment of NFM concentrates, which received financial support from NATO under its programme ""Science for Stability""."

Jan 1, 1988

By Leonid N. Shekhter, Corby G. Anderson, Esra Cankaya-Yalcin, Daniel G. Gribbin, Joseph D. Lessard, Larry F. McHugh

"A new process for smelting copper, Looping Sulfide Oxidation™ (LSO™) significantly and positively alters the smelting energy balance. This process uses copper oxide in conjunction with air for the desulfurization of copper and chalcopyrite concentrates. Copper oxide is regenerated in a flash type furnace and then ""looped"" back for the oxidation of the copper concentrate. Heat and material balances show that the Looping Sulfide Oxidation™ process requires significantly lower net energy than conventional technology. This process produces anode copper and higher S02 content off-gases for efficient formation of sulfuric acid. Additionally, the process yields slags with lower copper solubility as compared to the conventional technology.IntroductionBased on the positive results from LSO™ investigations [1], further lab investigations into co=on sulfides and metal oxides were performed. It was discovered that chalcopyrite (CuFeS2) is oxidized with copper (II) oxide. In this reaction over 98.5% of sulfur was removed as S02, while a significantly improved energy balance was observed. This paper intends to analyze both the conventional flash smelting process and the newly developed Looping Sulfide Oxidation™ process, comparing heat and material balance results. LSO™ yields improvements to the energy footprint for copper, opening the door to new copper processing opportunities."

Jan 1, 2013