Search Documents

By Donald O. Rausch, William E. Hawkes, Odin Jr. Strandberg

INTRODUCTION Kennecott Copper Corp.'s Tintic Div. Burgin mine is a 725 t/d (800 stpd) lead-zinc producer, located in the east Tintic mining district, 5.6 km (3.5 miles) east of Eureka, and 130 km (80 miles) south of Salt Lake City, UT. The Burgin mining complex includes three shafts, shop, dry, and office facilities, and a 454 t/d (500 stpd) flotation concentrator. Production and ser¬vice entry to the mine is through a 4.26-m (14-ft) diam concrete-lined production shaft, and a three-compart¬ment rectangular shaft. A connection with the Apex No. 2 shaft and the Burgin mine provides a second exhaust airway. Bear Creek Mining Co., Kennecott's exploration sub¬sidiary, began exploration of the Burgin mine area in 1957 with the sinking of the 335 m (1100 ft) deep No. 1 shaft. A station was cut at the 320-m (1050-ft) level of the shaft and extensive drifting, diamond drilling, and some winzing and raising confirmed the presence of a major lead-zinc ore body, the main portion of which oc¬curred below a hot saline water table. Surface facilities and the 4.26-m (14-ft) diam concrete-lined production shaft were completed in 1966. Ore production has been steadily increased to 725 t/ d (800 stpd) since 1966. The collar elevation of the No. 2 production shaft is 1731 m (5678 ft) above sea level. The mine's three levels, the 1050, 1200, and 1300 are at elevations of 1414.6, 1356.4, and 1338.1 m (4587, 4450, and 4390 ft), respectively. The approximate elevation of the hot saline water table is 1382.6 m (4536 ft). The earliest production on the east Tintic mining district was from the Eureka Lilly mine in 1909. Later, in 1916, the Tintic Standard mine was discovered, and pro¬duced ores with a gross value of $80,000,000 through 1956. The Eureka Standard mine located 1.6 km (1 mile) southwest of the Burgin mine produced ore worth $12,000,000 from fissures in the Tintic quartzite along the Eureka Standard fault. Ores produced from the east Tintic mining district through 1971 are valued at $151.3 million. The production from the entire Tintic district is approximately $500 million. GEOLOGY The Burgin ore deposit occurs as replacement bodies in limestone, dolomite, and shale. Numerous fault struc¬tures and rock formations make the mine geology com¬plex. The mineralization is strongly associated with sev¬eral major geological features, which include the Ophir formation, consisting of limestone, dolomite, and shale as the favorable host rock, and the structural influence of the east Tintic thrust, the Eureka Standard and sev¬eral other significant faults. Fig. 1 depicts the Burgin 1300 level workings, a generalized configuration of the ore body, and the main geological features. Covering the quartzite, limestone, dolomite, and shale facies enclosing the Burgin ore deposit are 183 to 274 m (600 to 900 ft) of andesite. The Burgin ore consists of massive sulfide and oxide lead-zinc ores with significant silver and cadmium val¬ues. The main ore minerals are galena, cerrusite, and spalerite. Extensive manganese oxide deposits are associated with the lead-zinc ore occurrence. A limited

Jan 1, 1982

By S. Bellec, P. Champagne, J. Châteauneuf, A. Berton, S. Fortier

"The start-up of new plants, extending from the commissioning of equipment to the production ramp-up, is a critical period where the processing circuit operation must be done in a structured and well controlled way to enable the gradual, safe and rapid achievement of production targets. The magnitude of the many risks associated with this pivotal period is accentuated in the actual context of low commodity prices. However, the implementation of a method that analyzes risks associated with a start-up, their probability of occurrence and their impacts leads to the identification of a series of preventive actions that can be applied in order to reduce potential negative impacts.Soutex has been involved in numerous start-ups over the last few years and has developed a structured methodology to assess this crucial period, maximize the pre-start-up preparation, ensure a smoother and safer ramp-up period and minimize the time needed before reaching commercial production.This paper describes a method to identify preventive actions to apply in order to reduce risks related to a plant start-up. Then, the various steps of the method are demonstrated using the industrial case study of the Canadian Malartic gold plant situated in Abitibi, Québec. The specific preventive actions, during start-up, the organisational measures and the ramp-up plan are detailed as they were effectively achieved. Finally, the post start-up actions are presented as well as some key results illustrating the achievement of their prior defined objectives.IntroductionPlanning a new plant or new circuit start-up in a mine installation involves various risks, both at the economical and safety levels. Unprepared staff and equipment can lead to safety issues that could threaten plant staff as well as the environment. Moreover, a poorly prepared start-up could often lead to equipment break-down, production stoppages and delays, leading to important economic impacts, delaying commercial production and therefore affecting directly the profitability of mining projects.It is common in the industry to have structured commissioning procedures for major equipment taken separately. Technical personnel from the equipment manufacturing company would usually come on site in order to perform the pre-operation verification, dry runs and the first hours of operations. This kind of assistance is usually focussed on one piece of equipment and neglects the interactions between the various equipment of the production chain. The commissioning phase is usually maintenance oriented and the information given by the manufacturing representative seldomly flows through the operation staff (in the case of this paper, the denomination “staff” refers to both managing and operating employees). The global process is usually not taken into consideration by the technical personnel sent on-site by the manufacturer during the commissioning phase. Many papers can be found describing the commissioning of new equipment focussing on the technology (Côté and Adante (2009), Wells et al (2007)) but without dealing with its integration process in the complete production chain."

Jan 1, 2016

By André R. Laplante

"This presentation reviews three continuous centrifuge separators, the Falcon-C, Kelsey Jig and Multi-Gravity Separator, two units with possible synergies with centrifuges, the In-Line Pressure Jig and InLine Leach Reactor, and two centrifuge prototypes, the continuous Knelson and the Altair Jig. Typical applications, potential problems, promising synergies and general concentration mechanisms are discussed. A general discussion on the sources of information, the nature of the fluidization water flow, test work for potential centrifuge separations and the early life cycle of new technology, using centrifuge separators as an example, follows. ResumeCette présentation fait le point sur trois appareils de séparation centrifuge, le Falcon-C, bac oscillant Kelsey et Multi-Gravity Separator; deux appareils qui présentent des synergies possibles avec les centrifuges, le bac oscillant In-Line Pressure Jig et le système InLine Leach Reactor; et deux prototypes centrifuges, le Knelson continu et le bac oscillant Altair. On y présente des applications typiques, les problèmes d’opération les plus usuels, les synergies les plus intéressantes. On discute également des sources d’information disponibles pour le minérallurgiste, de l’impact du mode d’ addition de l’eau de fluidisation, de la démarche expérimentale a faire avant d’installer un centrifuge, et du cycle de développement de nouveaux équipements, en utilisant les centrifuges comme exemple.IntroductionGravity separation has undergone a renewal in the past 20 years, much of it attributed to centrifuge units. The semi-batch Knelson Concentrator has probably received the most exposure, but it is rather because of the shear number of units sold than the width and breath of its applicability. It excels at recovery very dense minerals in very small concentrations, and has become a workhorse of the gold industry. Falcon’s Super-Bowl comes a distant second, with very similar applications. A number of copycats are available, and are generically identified as “Knelsons.” This presentation will not address these units explicitly, but as possible synergies."

Jan 1, 2000

By M. A. Trevits, A. Ozmet, A. C. Smith, J. B. Walsh, T. P. Mucho

Improvements in remote fire fighting technology are needed to reduce miner exposure to the dangers of fires and possibly save the lives of those who may become trapped. The National Institute for Occupational Safety and Health, in cooperation with U.S. Foam Technologies, Inc1., conducted a series of experiments at the NIOSH Lake Lynn Experimental Mine to study the stability, transport, control and fire extinguishing effectiveness of nitrogen-enhanced foam technology. This paper presents a description of the mine test configurations and experimental results

By C. N. Harman, N. S. S. Rama Rao

Production of Ferro-alloys through submerged electric arc furnace involves use of electric power as one of the major inputs. Hence the production by this power intensive process can be made economically more competitive if the specific power requirement for smelting each ton of the product is brought down. This becomes all the more necessary where the power cost is comparatively high, like in India. Since the day FACOR started production of Ferro Chrome in 1968, briquetted chromite fines along with lumpy ores were used as feed. Subsequently the increase in the proportion of briquettes and reduction in lumpy ore helped in increasing the use of chromite fines and also brought down the specific power requirement. Meantime FACOR had been closely watching the technical development of use of sintered pellets in Outokumpu and SRC Processes which need still lower specific power. But the high capital requirement for a pelletisation plant kept FACOR from introducing pellets feed to their Ferro chrome furnaces. So this was postponed to be adopted in future. In February 2004 in the ?1st Ferro-Alloys India?, a paper [1] was presented by Dr. Amit Chatterjee. In the questions period after the presentation of the paper there came up a discussion in which it was revealed that with the Indian high grade chrome ores it was not possible to make sufficiently strong pellets, unless a larger percentage of bentonite is used as binder. This is because the Indian high grade Chrome ores have different mineralogy of gangue content compared to low grade ores in Finland and South Africa. Higher usage of bentonite gives rise to higher slag volume and this would result in increased specific power. Since FACOR had plans to go in future for sintered pellets feed, this gave rise to a doubt on success of pelletisation for Indian high-grade chrome ores. This prompted FACOR to take up experimental production of sintered chromite pellets and use of the same in one of their existing furnaces for production of high carbon Ferro chrome. The results are encouraging and are summarized in the paper.

Jan 1, 2007

By Jessica Egan, Daniel Hodouin, Mohammed Reza Khalezi, Steve Bellec, Claude Bazin, Carl Duchesne

"A model for gold leaching was developed and implemented into a simulator. The simulator uses a description of the ore that is based on the mineral composition and precious metal content. The model accounts for the distribution of minerals and precious metals through the size intervals. An ore texture model based on precious metals and minerals grain sizes within the ore is used to predict the exposed surface of the species in the various size intervals. A model is proposed to predict the rate of dissolution of any species dissolution using the exposed surface, particle size, cyanide and oxygen concentrations, temperature, pH and agitation. The flow of slurry through a leaching tank is modelled using a parallel arrangement of perfect mixers to simulate a bypass and a Cholette-Cloutier mixer model. The simulator can be used for circuit optimization but was developed to provide an environment for learning the basic concepts of process analysis methods. Examples are given to illustrate the application of the simulator for planning tracer tests and sampling campaigns.INTRODUCTIONThe constant pressure to improve the operation of processes that are already close to optimum imposes to plant engineers to be aware of the available process analysis tools and to be able to use them to assess process operation and make a diagnosis to possible problems. Some of these tools are:•,Sampling the streams of a process;•,Data reconciliation;•,Analysis of mixing in reactors;•,Estimation of rate parameters;•,Optimal tuning and flow sheet modification;•,Automatic control and real time optimization.Although some of these tools are part of the curriculum of many university engineering programs, the students are not exposed to actual process analysis problems. In addition the complexity of the ore dressing processes compounded with unavoidable measurement errors and plant disturbances can discourage many motivated engineers. These factors often lead to an incomplete valorization of the collected data and a poor return on the investment associated with the sampling, testing and analysis of the samples.Simulators are readily available for process optimization (Yalcin and Shang, 2006) by allowing:•,The simulation of various flow sheet configurations;•,The simulation of a change of operating conditions;•,The simulation of various control strategies;•,The training of plant operators.However few simulators have been developed with the objective of providing an environment for training plant engineers and technicians to the use of tools for process analysis and optimisation."

Jan 1, 2008

One of the most important goals of the experiments is to determine deformation and strength of the rock specimen under applying triaxial load, the status of failure condition is one of the subjects which can be used in soil mechanic and foundation engineering applications. To investigate the effect of confining pressure on the triaxial test, the rock has been considered as bonded-particles method and has been simulated by particle flow code three dimensions (PFC3D). This model, does not have pre-existing microcracks and all the particles have the same size (2 mm diameter), equal to the real specimen shape. To compare the mechanical behavior and failure pattern of the numerical and experimental results at uniaxial and triaxial tests at the same conditions, the Young's modulus, Possion's ratio as well as maximum axial stress have been considered. On the other hand, the microcracks growth and change of failure pattern at the modelling of the uniaxial and triaxial tests with different confining pressures up to failure point were reported. According to the experimental work, the number density of microcracks decreases from starting value and remains almost constant up to the failure beyond that point. The comparison of the numerical and experimental results of maximum axial stress and the Possion's ratio revealed good accordance. The initial number density of microcracks at the model was zero and increased while microcracking. Also, the sudden increment around the maximum stress was observed which is because of unstable growing of microcracks near the maximum stress. In all uniaxial and triaxial tests with different confining stresses, the number density of microcracks during the failure remains almost constant which can be considered as a proof of failure occurring in the model. The experimental results indicate the similar trend as well.

Nov 25, 2010

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

By Willie M. NeSmith

Conventional augered, cast-in-place (ACIP) piles were introduced into the New York City area as a result of the damage to existing structures caused by pile driving operations. ACIP piles are often specified where deep foundations are to be installed adjacent to transit facilities, sensitive underground utilities or in close proximity to existing structures. However, loss-of-ground issues associated with the installation of ACIP piles have prevented the wide-scale use of these systems. Beginning in 2002, Berkel & Company Contractors, Inc. began using its augered, cast-in-place displacement (ACIPD) system in the New York City area. Like conventional ACIP piles, this system produces almost no vibration. Also, as almost no material is brought to the surface, there is no opportunity for loss of ground. This paper presents a description of Berkel's displacement pile system and a brief discussion of six projects in the New York City area that have been executed with this system over the past two years.

Jan 1, 2004

By Daniel Su

Approximately 90% of the primary roof bolts used in CONSOL?s Pittsburgh seam coal mines is 2-piece, 8-foot long, 7/8? (or ¾?), high-strength, resin assisted, mechanical shell tensioned bolt. The remaining 10% is the 2-piece, 8-foot long, 7/8? combination bolt, which employs 4 feet of fast resin to anchor the deformed rebar at the top of the hole. In either system, a 1-3/8? hole is required to accommodate the mechanical shell and the coupler. The cheaper torque-tension rebar system, which is typically fully-grouted with 2-speed resin and which typically provides low bolt tension, is not used in CONSOL?s Pittsburgh seam mines. Rather, it is used in CONSOL?s Central Appalachia mines, where the roof rocks have CMRR rating of 50 or higher. Fully-grouted headed rebars, on the other hand, are used in CONSOL?s room-and-pillar mines. The selection of tensioned versus non-tensioned, fully-grouted bolts for coal mine primary roof support has been debated for the past thirty years. Many researches have been conducted to understand the theoretical bases behind the two systems. This paper describes CONSOL?s experience of using a new fully-grouted, mechanical shell tensioned bolt in the Pittsburgh seam with the development of low insertion force resin.

Jan 1, 2007

By J. A. McLennan

Geological uncertainty is an unavoidable characteristic of all mining projects since only limited information is available from sampling. Mine planning and development decisions with significant economic consequences are made when the geological heterogeneity is inherently uncertain. Geostatistical simulation is preferred over kriging because the methodology provides alternative property realizations that can be combined into a model of geological uncertainty. Geological uncertainty can be transferred into production uncertainty, which can help characterize the economic risk of the project. This paper presents a case study for the Pogo property, being prepared for development near Fairbanks, Alaska. The exact dimensions, grades and production predictions have been modified; however, the methodology is illustrative. The geostatistical methodology consists of (1) assembling the relevant drillhole data and establishing a suitable coordinate system, (2) calculating the target distribution, (3) creating a model of spatial correlation, (4) generating multiple realizations at a small scale and (5) linearly averaging all the realizations to the chosen selective mining unit (SMU) support size. The geostatistical model is then used to calculate production uncertainty.

May 1, 2004

By Manuel R. Lastra

Critical to successful dump and heap leaching for gold, silver, copper and uranium are factors such as permeability, solution delivery to the ore, and solution recovery. This paper deals with possible techniques for successful accomplishment of these three factors. New developments as well as older techniques are discussed, together with rationale for use of some techniques in reference to others. The authors hope to present a checklist so that the ideal application to individual mine situations can be achieved. This involves a discussion of the merits of each different method and the situations for most logical application. It is hoped that such discussion will broaden the geographic areas where dump and heap leaching can be applied to include greater winter cold and tropical regions of large amounts of rainfall.

Jan 1, 1984

By Jason J. Crowder

Presentation Outline ? Introduction ? Costs of ground support and rehabilitation ? Why post-failure rock mass properties are necessary ? The Rock Mechanics Problem ? Present State of Modelling and Instrumentation in Mining ? Case Study Background ??Williams Mine ? Deriving Parameters for Modelling from Instrumentation ? Results from Case Study ??Back Analyses ? Discussion of Research Impact t Summary

May 1, 2006

By H A. Myburgh

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities. Background The Kumba Resources Sishen Iron Ore Mine in South Africa produces 26.5 Mt iron ore per annum from its beneficiation plant. The ore body consists mainly of laminated and massive type hematite ore that is crushed down to ?90mm before being beneficiated by means of a combination of Wemco drums, Larcodem and dense medium cyclone separators. The need for higher densities When the percentage of high-density gangue2 is higher than normal in the run-of-mine (ROM), a higher separation density is necessary to produce a product to specification. Certain ore types of this quality in the Sishen reserves require a separating density higher than 4000 kg/m3, whereas densities would normally average 3600 kg/m3 when beneficiating ores of normal high-density gangue content. Sink and float tests conducted on the ROM material at Sishen revealed some interesting characteristics. In the waste fraction, (density < 3600 kg/m3) it was found that the %Fe was <21% (Fig. 1). Similarly, for the product fraction (density >3000 kg/m3), the percentage Fe varied between 35% and 67.2%. The bulk of the material (88%) actually had a density greater than 4000 kg/m3 and a Fe content that varied between 63% and 67.2%. At a density interval of 3600 to 4000 kg/m3, the Fe content varied from 37% to 60% with an average of 45%.

Jan 1, 2006

Sequential and evolutionary changes through time are recognizable in many, perhaps most major families of ore deposits and their geological environments. These changes are additional useful indicators of the evolutionary history of the earth and its tectonic processes. They are important in mineral exploration because they involve consideration of time as a fourth dimension, thereby indicating the most favorable ages, rather than types of rock for investigation. Many of the changes are analogous to those recognized in faunal evolution. Some primitive, unspecialized types of ore deposits occur nearly unchanged through rocks of widely differing age. Others diversify into several, more specialized variants, whereas still others become extinct. The place of these is taken by new, younger types, some of which undergo sudden proliferations and later diversifications of their own. In Archean greenstone belts irrlportant iron, nickel, gold, and base metal deposits occur co-regionally, but in different stratigraphic positions in the same, thick volcano-sedimentary successions. Here their close temporal and spatial associations suggest common genetic exhalative hydrothermal processes. The massive base metal sulfide family of ore deposits provides an excellent example of evolutionary changes, exhibiting distinct variations through both time and space. Deposits belonging to this family span the entire range of time, occurring in rocks of ancient Archean to Recent age, and specific types within the family also span the entire range of spatial environments from ensimatic to ensialic. Moreover there are possible evolutionary metallogenic links between certain types of massive base metal sulfide deposits and other important base metal ores, noteably Mississippi Valley-type and porphyry copper deposits.

Jan 1, 2013

By L. Tonc

In 2004, the engineers at the Deer Creek Mine located near Huntington, Utah initiated the ventilation planning to exploit a remote area of the mine?s reserves. This area was located under a mountain which would not allow for the incorporation of an additional shaft or portal access near the proposed longwall panels. With this constraint along with the desire to maintain a two entry gate road system and the expected condition of frequent coal wash outs a ventilation plan was established. Different options were examined that included; increasing the current exhaust fan power, adding another exhaust fan installation, converting the ventilation fans in the active portion of the mine to a forcing system, and modifying the ventilation system in the active area of the mine to a push-pull system. The push-pull ventilation system was ultimately selected. This paper details the design process of the ventilation system upgrade, the procurement process for the new fans, and the new fan startup testing.

Jan 1, 2009

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By Philip J. Daynes

As part of the regeneration of the centre of Dublin, a multi-functional development is being constructed on the site of the historic Smithfield Fruit Market. The site is being developed in three phases, and includes one of the deepest basements (10m) constructed in Ireland to date. Until the recent improved economic climate, there has been little requirement for deep basements in Dublin, and this is the first to be constructed entirely within fluvio-glacial gravels and boulders. The difficult ground conditions led to the adoption of a diaphragm wall solution to ensure a watertight construction. Tie-back anchorages are utilised in the temporary case, and the wall is propped by floor slabs in the permanent case. Where required by high bedrock levels, the diaphragm wall is dowelled into limestone bedrock to ensure toe stability. The recorded lateral movement of the wall is significantly below that calculated by numerical analysis. Temporary bentonite cut-off walls were installed to divide the site into discrete sections. The basement was constructed as a tanked structure, and is subject to uplift water pressure. Passive tension minipiles provides an innovative alternative to the standard stressed anchorage solution. This paper describes:- design and construction aspects of the diaphragm wall, tie-back anchorages, and anti-flotation minipiles, together with recorded lateral wall movements,

Jan 1, 2003

By J. Greg Sanchez

The New South Ferry Terminal in the New York City Transit system represents an important milestone for the city. This is the first station designed and built in the 21st century. The design of the fire safety system included relying on Computational Fluid Dynamics to analyze the dispersion of heat and smoke, and modelling of people egress to determine the egress requirements. The project also looked into how to protect the structure from the heat exposure in order to meet the fire rating requirements. This paper provides an overview of the fire safety design approach taken to design the new South Ferry Terminal station in lower Manhattan and looks into fire modelling, structural fire protection, and station evacuation.

Jan 1, 2008