Search Documents

By M. A. Dayananda, R. E. Grace

Vapor-solid diffusion couples were employed in a study of ternary diffusion in the single-phase copper-rich corner of the Cu-Zn-Mn system Interdiffusion coefficients were measured at three different compositions corresponding to the intersections of diffusion paths determined at 850°C. Intrinsic diffusion coefficients were determined at two compositions by the Philibert-Guy method. New relations between the various intrinsic diffusion coefficients are also presented. MOST of the investigations of ternary diffusion have been made with "sandwich" couples formed by welding together two homogeneous solid solutions with or without markers placed at the interface. With such couples Kirkaldy and his coworkers1,2 have determined interdiffusion coefficients which describe ternary diffusion in the substitutional alloy systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy3 have reported intrinsic diffusion coefficients for Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.4 The use of semi-infinite diffusion couples, for example, vapor-solid couples, where the diffusing species are supplied from a vapor source in contact with a diffusion disk, has so far been confined to studies of binary diffusion. Balluffi et a1.5,6 have successfully determined the interdiffusion as well as the intrinsic diffusion coefficients in several binary metallic systems employing vapor-solid couples with markers initially placed at the vapor-solid interface. They have also discussed the general advantages and limitations of such couples. Vapor-solid diffusion couples can successfully be employed in ternary diffusion studies. The importance of such couples in ternary diffusion lies in the fact that inert markers lie close to the vapor-solid interface, and the composition of the marker plane is virtually known before experimentation begins. Another minor advantage is that the method of Philibert and Guy4 may be used with three alloys instead of four. Lastly, the diffusion paths need not be S-shaped, as pointed out by Meijering7 for "sandwich" couples. The Cu-Zn-Mn system is convenient for ternary diffusion studies because of the large single-phase field in the copper-rich corner. The vapor pressure of zinc above such alloys is known, and X-ray measurements indicate that the molar volume is nearly constant over a wide range of compositions.8,9 It is the purpose of this paper a) to extend the analysis of Balluffi and seigle5 to permit an evaluation of interdiffusion coefficients in ternary vapor-solid couples, b) to use the method of Philibert and Guy to determine intrinsic diffusion coefficients with such couples, and c) to present experimental data on both interdiffusion and intrinsic diffusion coefficients for the Cu-Zn-Mn system at 850°C. INTERDIFFUSION IN TERNARY VAPOR-SOLID COUPLES The analysis of Balluffi and seigle5 is extended in this section to a vapor-solid couple where two solutes diffuse from a vapor source into a ternary solid solution. To take into account the expansion of the diffusion disk caused by the absorption of mass from the vapor phase, the total fluxes are expressed on the basis of a coordinate system that moves with the velocity of the vapor-solid interface; thus. where D3ij are the intrinsic diffusion coefficients,4 v(x, t) is the local Kirkendall velocity of mass flow, and F(t) is the negative velocity of the vapor-solid interface (x = 0). Both these velocities are based on a fixed coordinate system far removed from the diffusion zone. Using the continuity relations and Darken's method1' for a ternary system in which components 1 and 2 diffuse from the vapor phase into a solid of negligible vapor pressure, one obtains

Jan 1, 1965

By J. F. Butler

Boron nitride, BN, has been identified in boron low-carbon steels by means of light microscopy, electron microscopy and diffraction, and chemical analysis. This boron nitride is responsible for strain aging suppression in these steels through the removal of nitrogen from solution; however, small oxidizing potentials which result in deboronization In the austenitic temperature range also result in boron nitride decomposition and the subsequent occurrence of nitrogen strain aging. THE addition of boron to low-carbon steels is an effective means of eliminating the detrimental effects of strain aging;',' however, the mechanism by which boron suppresses strain aging has not been established. In studying the effect of heat treatment on the strain aging of boron low-carbon steels, Butler3 found that no detectable nitrogen was present in the ferrite solid solution after various heat treatments even though the total nitrogen analyses of the steels were 0.003 pct N. Apparently the function of boron in suppressing strain aging is the removal of nitrogen from solution to form a relatively stable second phase. A clue to the identity of this phase was found by Speight4 who extracted from an aluminum-killed boron steel an acid insoluble residue which contained boron and nitrogen in proportions corresponding to the compound, BN. Shyne and Morgan5 found that the addition of nitrogen to a hardenable boron steel lowered its hardenability in a manner which suggest-d the presence of nucleating particles (presumably BN) even at high austenitizing temperatures. Although this indirect evidence for the presence of boron nitride in boron steels has been found, the compound was not identified metallographically as a separate phase in these steels. Because boron has an affinity for oxygen comparable to that of silicon,5 boron steels must be thoroughly killed with aluminum in order to prevent the reaction of boron with oxygen.7 The affinity of boron for oxygen also is demonstrated through the ease of deboronization of a boron steel in an oxidizing atmosphere. Digges, Irish, and Carwile8 found that a mixture of wet natural gas and air caused both deboronixation and decarburization of a boron steel at 1900°F. The boron content rose at the surface of the steel due to the formation of boron oxide. Shyne and Morgan9 encountered deboronization at much lower oxygen potentials; loss of boron occurred in steels treated at 1750o F under argon purified to 0.0014 pct 0, even though decarburization did not occur. Boron oxide, B2O3, is much more stable than the nitride, BN, as is indicated by the standard free energies of formation at 980oC: -235 kcal per mol of B2O3 (liquid) and -28 kcal per mol of BN (crystal). It is evident that the oxygen potential must be kept low in the presence of BN in order to prevent its decomposition and the subsequent formation of B2O3' The purpose of the work described in this paper was to identify the nitride phase responsible for the removal of nitrogen from solution and to study its stability under oxidizing conditions. IDENTIFICATION OF BN In order to identify the phase containing boron and nitrogen, several alloys high in boron and nitrogen were made up in a small vacuum furnace. In alloys 3 and 4, Table I, electrolytic iron was used as a charge material. Boron additions were made in the form of 18 pct B ferro-boron after the iron was molten. In the case of alloy 3, the charge was solidified at this point; for alloy 4, nitrogen at 1 atm pressure was admitted over the melt before it was

Jan 1, 1962

By Charles W. Carter, Alfred H. Bell

In 1943, Illinois produced 82,256,000 bbl. of oil, or 5.5 per cent of the total for the United States, and ranked sixth in the nation in oil production. This represents a decline of 23 per cent from 1942, when the total Illinois production was 106,ggo,o~~ bbl. and Illinois ranked fifth. The daily average production for 1943 was approximately 225,000 bbl. Daily averages by months were as follows: Jan......... 238,000 July......... 218,000 Feb......... 240,000 Aug......... 216,000 Mar......... 237,qoo Sept........ 220,ooo Apr......... 230,000 Oct......... 220,000 May....... 221,000 Nov......... 223,000 June......; . 222,000 Dec......... z18,ooo This shows that most of the decline during the year took place between March and May, and that for the last eight months of 1943 production has been essentially steady. This means that there has been enough production from new wells drilled to balance the natural decline of the Older wells. The trends of drilling and production are shown in Fig. I and Table 3.

Jan 1, 1944

By Alfred H. Bell, Charles W. Carter

In 1943, Illinois produced 82,256,000 bbl. of oil, or 5.5 per cent of the total for the United States, and ranked sixth in the nation in oil production. This represents a decline of 23 per cent from 1942, when the total Illinois production was 106,ggo,o~~ bbl. and Illinois ranked fifth. The daily average production for 1943 was approximately 225,000 bbl. Daily averages by months were as follows: Jan......... 238,000 July......... 218,000 Feb......... 240,000 Aug......... 216,000 Mar......... 237,qoo Sept........ 220,ooo Apr......... 230,000 Oct......... 220,000 May....... 221,000 Nov......... 223,000 June......; . 222,000 Dec......... z18,ooo This shows that most of the decline during the year took place between March and May, and that for the last eight months of 1943 production has been essentially steady. This means that there has been enough production from new wells drilled to balance the natural decline of the Older wells. The trends of drilling and production are shown in Fig. I and Table 3.

Jan 1, 1944

By Earl R. Hoskins, James E. Russell

The electrical resistivity of rocks has been studied quite extensively, in particular, the effects of temperature and confining pressure on resistivity. References 1 through 6 at the end of this chapter pertain to electrical resistivity of rock and contain further references on the same topic. The present study is motivated by an interest in determining the in-situ properties of rock as well as the stress state of the rock and how these quantities are changing with time. Most of the previous work on the electrical resistivity of rocks has been directed toward saturated rocks at relatively high confining pressures and temperatures. The present study was oriented towards air-dry surface rock that might occur in mine pillars. The mean stress and temperature under such conditions are comparatively low. It has been demonstrated that the resistivity of rock is highly dependent upon the porosity. In fact, for saturated rocks, a relationship referred to as Archie's law has been established between porosity and electrical resistivity. In the case of saturated rock, the property that is actually being measured is the resistivity of the solid/fluid system. Since the resistivity of the fluid alone is usually much lower than that of the dry rock, it is understandable that the resistivity of a saturated rock is in general several orders of magnitude lower than the resistivity of a relatively dry rocli. For dry rock, it seems reasonable that the electrical resistivity should increase as microcracks open within the material. Since microcracks open as material is stressed closer and closer to its failure point, it appears that there should be a correlation between electrical resistivity

Jan 1, 1970

By Robert E. Tally

A recorded in the account of the Annual Meeting, on another page, the report of the tellers showed that all men nominated by the committee, which included Messrs. Wilber Judson, E. DeGolyer, W. A. Weldin, J. A. Norden, J. D. MacKenzie, Wilfred Sykes and S. Skowronski, were duly elected to the offices for which they were nominated. Robert Tally, who was elected to the presidency for 1931-2, is well known to all our members not only because he has served on the Board of Directors since 1928, but through a brief outline of his great achieve¬ments in his chosen profession pub¬lished in our issue of December last. The vice-presidents, Howard N. Eavenson and H. A. Guess, are also well known to our members. Mr. Eavenson has not only been chairman of the Coal Division since its organization, but was also a Director during 1917, 1918 and 1919., Mr. Guess was Director in 1926, was elected a vice-president by the Board last year to fill the vacancy created by the election of Mr. Bassett to the presidency, and is now elected to the usual three-year term.

Jan 1, 1931

By T. A. Read, M. S. Wechsler, D. S. Lieberman

IN the formation of martensite in steel, it has been observed that the habit plane does not change continuously as the alloy content is varied. Instead, it appears that discrete habits correspond to certain ranges of composition. Greninger and Troiano' found that in low-, medium-, and high-carbon steels, the habits are approximately (1l1), (225), and (259), respectively.* The work of Mehl and Van Winkle2 indicated that the change from the (225) to the (259) habit is fundamentally a consequence of the lower transformation temperature rather than the higher carbon content. Also, Otte and Read3 observed that the habit plane orientation for a chrome-carbon steel scattered within a cone of semivertex angle of 5 deg, which was outside of the experimental error in the determination of the habit plane. These observations suggest the importance of investigating what factors in the crystallography of the formation of martensite account for the several types of habit and the inherent scatter in the precise orientation of the habit plane. A theoretical treatment of the austenite-martensite transformation has been given,4 which considers the total transformation distortion to be composed

Jan 1, 1961

By E. M. Wise

THE properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. GENERAL REQUIREMENTS In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should be good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depilatories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 lb. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800° and 1200° C.

Jan 1, 1928

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By T. A. Rickard

In a former paper* the writer has described the essential features of the general geology of the Cripple Creek region. In the present account it is intended to examine into the occurrence of the ores, the value of which has made this district the most important among existing American gold-fields. The production of Cripple Creek from its discovery, in 1891, to the close of 1901, has reached a valuation of fully $125,000,000. During the past year (1901) the output amounted to $17,285,470. In 1900 it was $18,174,681. The first discoveries, which led to the development of the district, were made in the spring of 1891, but it was not until 1893 that vigorous work was commenced. A great impetus was then given to the exploration for gold on account, of the sudden drop in the market-price of silver, caused by the closing of the Indian mints in the summer of that year. This induced an energetic population from the older silvermining camps of Colorado to go to the new gold-field, which was then beginning to attract attention. Prospecting, at first, was hindered by the comparative absence of outcrops, due to the fact that the surface of the hills is covered with a considerable thickness of shattered rock, resulting from the action of frost at a high altitude; but so much indiscriminate digging was done that a number of rich veins were uncovered, and this stimulated the search for others. The advanced condition of the mining industry of Colorado offered unusual facilities for exploration and reduction; progress was therefore rapid, with the result that the district soon achieved great prominence.

Jan 1, 1903

By F. H. Deily, H. W. Lownie, E. A. Loria, L. W. Ledgerwood, M. W. 207-000-000-012 Mallett, J. E. Eckel

MANY investigations have been made of the residual gas content of iron and steel. Very few, if any, quantitative measurements have been made on the oxygen content of cupola-melted iron.' The fact that cast iron is a complex alloy rather than

Jan 1, 1957

By N. J. Grant, Per Knudsen, J. T. Blucher

The fatigue behavior of three SAP alloys was studied in ternzs of strain rate and temperature, at high strains. The k values in the modified Manson-Coffin equation, Nk4 = C, were less than 0.5 under all test conditions, and change with strain amplitude for the lower-oxide alloys at about 2 pct strain. Lowest k values were near 0.25. Strain rate had no effect on life at 80 F, but had an increasingly greater effect with increasing temperature above 500". Life decreased with decreasing strain rate, above 500"F, and with increasing temperature. Ductility at fracture in a tension test was indicated to be an important factor in determining 1ife in these big+-strain tests with the SAP alloys. INEVITABLY, in the course of mechanical tests at elevated temperatures, particularly if significant time at temperature is involved, there are large changes in structure; these changes make it difficult to relate behavior patterns over ranges of temperature or strain rates at high temperatures. Such changes are to be expetted in low cycle fatigue at low strain rates and high temperatures. Accordingly, it was of great interest to examine the low cycle fatigue behavior of SAP / an aluminum oxide dispersion-strengthened aluminum, a type of alloy which had shown unusual structure stability to temperatures as high as 1000" to 1150°F and resisted recrys-tallization essentially to the melting temperature.'j3 Since the matrix is pure aluminum, there are no complications of averaging, agglomeration, or phase solution. It was also desirable to check the Manson-Coffin equation4?' for the SAP alloys, namely N~E~ = , where ep is the total plastic strain amplitude, k and C are constants, and N is the number of cycles to failure. Here, too, was an opportunity to check the roles of temperature and strain rate with a very stable material. Tavernelli and coffin6 had concluded that k had a value of about 0.5 for many alloys and C was equal to ~/2, where E is the fracture ductility determined from a static tension test. The results were obtained from low-temperature tests where creep and diffusion processes are unimportant. Manson7 found k = 0.6 fitted his data reasonably well; however, in later analyses of a large amount of low cycle fatigue data generated at room temperat~re@"~ he found k to vary from 0.6 for short lives to 0.21 for long-life fatigue tests. In the latter studies,89g Manson separated the total strain range into elastic and plastic components when he found that k was influenced by the nature of the strain. The use of EL (total strain) instead of EP (total plastic strain)4'5 makes a difference in the resultant k value. The ratio of changes with temperature, strain rate, and strain; further, there are the problems in the determination of the elastic strain. Based on these considerations, and the improved fit of points in a plot of by Wells and Sullivan,' is also utilized in these studies. Anderson and wahl,14 using commercial 1100 aluminum, and Blucher and Grant,15 using 99.99 pct pure aluminum, found an increase in life with increasing test temperature. Anderson and Wahl were the first to report low cycle fatigue results from SAP materials. With increasing temperature, the role of strain rate becomes more important. In this regard, care must be exercised to differentiate between frequency (wherein strain rate may vary from zero to a maximum in each cycle, sinusoidally, for example), and constant strain rate, as used in the present study, in a saw-tooth type cycle; in the latter case, the frequency is not specified but can easily be calculated from the strain and strain rate data. It has generally been found that life in low cycle fatigue tests decreases with decreasing frequency16 or with decreasing strain rate at elevated temperatures.15 Coffin,17 reviewing Eckel's work,16 also reported that k increased with decreasing frequency for acid lead, yielding values from 4.0 at a frequency fo 6.6 cycles Per day to 1-46 at a frequency of 7440 cycles per day; the value of k decreased to 0.58 at a frequency of 2.38 x lo6 cycles per day. EXPERIMENTAL PROCEDURE Three SAP alloys, of two nominal compositions, were tested. Alcoa supplied XAP 005 as 2-in.-diam extruded bar, of nominal composition A1-7 wt pct A1203. The Danish Atomic Energy Commission supplied SAP 930 (A1-7 wt ~ct Ala3) and SAP 865 (A1-13 wt pct Al&) manufactured by Swiss Aluminium Ltd., in the form Of $-in.-diam extruded rod. Metallographic comparison of the structures of XAP 005 and SAP 930 showed the former to have a more uniform oxide distribution. Button-head specimens were machined in the longitudinal direction of the bar with 0.4 in. gage length by 0.2 in. diameter, with a fillet radius of j-B in. After machining, the specimens were electropolished in a 1 to 4 mixture of perchloric acid to methanol to remove all machining marks. All test bars were in the as-extruded condition. The fatigue tests were performed on a hydraulically activated, axial strain machine, with complete reversal of strain.15 Test conditions were:

Jan 1, 1969

DEFENSE Materials Procurement Agency has been moving rapidly to encourage copper industry expansion programs. Although copper production is at a high level, a shortage exists on a world-wide basis as well as on the domestic scene. Projected expansion programs will not ease this current demand for most of them are 2 to 5 years off. Refining facilities are adequate but there is a shortage of ore and scrap, and it is for this reason that the expansion programs are directed at developing more sources of supply. The domestic expansion programmed thus far and understood to have been arranged with price escalation should the domestic price go to 271/20, were summarized by American Metal Markets as follows (dates of announcement are given in parenthesis: .1-Copper Cities Mining Co.'s, $15,000,000 expansion near Miami, Ariz., to be operating about 1954. DMPA will buy 22,500 tons of copper a year up to a given amount on an agreed price of 23¢ per pound, with some exceptions and depending upon salability at a higher price to other purchasers in the U. S. (September 25th). 2-An RFC loan of $60,000 to North Butte Mining Co. to be paid off on the basis of deliveries at a purchase price of 241/20 per pound (September 25th). 3-A $25,000,000 expansion program by Phelps Dodge to provide 38,000 tons per year by late 1954. DMPA would purchase it at a price of 22¢ per pound up to 112,500 tons providing other purchasers in the U. S. will not pay a higher price (September 26th). 4-Anaconda Copper Mining Co. $40,000,000 expansion in Nevada to provide more than 30,000 (might be increased to 45,000) tons per year. DMPA would purchase the copper at 250 per pound for a limited period of time if it is not salable to industrial users at above this price. Production would start around 1953 (November 14th).

Jan 1, 1952

Coal production during 1963 amounted to 446 mil- lion tons, an anticipated increase of about 6% over the 1962 production of 422 million tons. Electric consumption was 207 million tons, a continuation of its upward trend with an increase of about 7%. The metallurgical market consumed 77 million tons: the industrial market, 96 million tons; and the retail market, 26 million tons. Exports were 46 million tons. Modernization continues in the coal industry as it approaches the mid-1960's. The industry has shown a keen desire to explore and pursue new developments, new concepts and new managerial methods and techniques that have become so vital and important for industrial well-being.

Jan 2, 1964

By Colin Rae

THE absence of paraffin and other oil hydrocarbons in the soil, although they are concentrated in extensive deposits in some localities, the common distribution of plant remains through many formations that .are not productive for oil, and many other factors, seem to indicate the existence of an intermediate organic compound between the complex plant compounds and the petroleum hydrocarbons; and much evidence points to the humus acids or associated organic compounds, which are probably collected by surface waters and concentrated in certain areas by means of precipitation by electrolytes, which would be contained in sea water or possibly in various inland seas or lakes. PRESENT-DAY EVIDENCE There are many present-day evidences of the association of petroleum with humus acids. Binney, in 1912, made observations without explanations on the peat mosses of Down Holland, England, where he found petroleum being formed by decomposition, in the presence of an infiltration of sea water. The analysis of a typical peat will show its relationship to the humus acids under consideration. SAMPLE 'No. 1, SAMPLE NO. 2, PER CENT. PER CENT. Water : 20.0 29.5 Ash 3.0 3.05 Fiber 47.0 54.95 Humus acids 30:0 12.50 J. D. Haseman and others have noted the association of asphalt and hydrocarbons with the swampy, boggy areas, particularly adjacent to the sea.

Jan 2, 1922

By Harold Margolin, W. R. Hibbard, R. W. Fenn, H. P. Moore

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By Raymond M. Howe

Additional data have been secured on the disintegration of furnace linings and the spalling of stove brick. The first article on the disintegration of furnace linings appears to have been written by John Pattinson in 1876.l The furnace involved was 85 ft. (25.0 m.) higher and 27 ft. (8.2 m.) in diameter at the boshes; after being in blast five years, the top brick became contaminated with carbon and disintegrated. An examination of the lining showed that the discolored, disintegrated brick were in a zone found from 35 to 67 ft. (10.6 to 20.4 m.) above the hearth; immediately below, in a zone extending from 22 to 40 ft. (6.7 to 12.1 m.) above the hearth, the brick were hard and porcelain-like in appearance. Analyses of samples taken from the different sections are given in Table I. The water-soluble portion found in the sample taken 39 ft. (11.8 m.) above the hearth had a composition approximately as follows: silica, 0.50 per cent.; lime, 0.04 per cent.; potash, 0.78 per cent.; soda, 0.20 per cent.; potassium chloride, 6.19 per cent.; moisture, 1.03 per cent.; total, 8.74 per cent. The carbon Table 1.—-Analyses of Samples Taken from Diferent Sections of Furnace . I ii In Iv v Section 67 Section 45 Seotion 39 Section of Original ft Above ft above ft above vitrified Lining Hearth Hearth Hearth Portion Per Cent. per Cent per Cent per cent. per Cent Silica........................... 55.70 55.60 55.67 47.60 37.07, Alumina........................ 35.50 35.40 30.00 26.47 23.18 Ferric oxide..................... 3.00 1.32 0.96 Lime........................... 0.23 0.06 0.17 Magnesia....................... 1.22 0.95 0.86 0.00 Potash......................... 2.60 2.10 5.30 7.54 21.59 Soda.........,.................. 0.45 0.42 1.67 0-76 6.28 Ca1bon ......................... 2.05 3.24 5.97 Carbon dioxide.................................. 2.. 17 Water...................................... 7.70 Water-soluble........................... 8.74

Jan 1, 1920

By A. L. Sweetser

Experience has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorina-tion-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave: Fe,O,, 3.35; FeS, 1.5; MnO,, 0.75; ZuCO,, 4; A1,0,, 3.20; H,O, 0.7 ; SiO, and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size—a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Jan 1, 1908