Search Documents

By G van Niekerk, M Wortley

Screening is a critical part of many mineral processing circuits and keeping the aperture of the screening media within specification is vital to ensure efficient performance of the processing plant. Typical ways of estimating and/or measuring the wear of the screening media vary from very subjective methods (for instance, using the human eye) to manually checking the width of a few of the more severely worn gaps with a measurement device. Subjective methods can be flawed by human error while manual checking can distort the polyurethane or rubber materials that are used in several types of screening media. All of these errors can cause either premature replacement of panels or, even worse, poor screening of the material.Metso Process Technology and Innovation (PTI) and Metso Screening Media Solutions (SMS) have developed an innovative method that measures screen aperture using advanced image processing techniques. Field trials of the device are presented in this paper, which shows the comparison between the different methods of measuring apertures. Case studies demonstrate how the system, when combined with ScreenTrack, MetsoÆs industry leading maintenance system, and screening media, is providing users with the best possible screening solutions.

Sep 26, 2011

By JOHN G. RAYNER

An examination was made of the filtration characteristics of a haematite slurry using a range of polyacrylamide based flocculants in solutions containing up to 3 per cent sodium chloride. The polymers used were "high" and "Iow" molecular weight and had from 0 to 40 per cent charged groups.Increasing charge density tends to reduce the dose required to achieve optimum performance measured by filtration rate and by cake moisture. In general increased salt addition tends to increase the dosage required to achieve these optima. Both these observations result from the change in polymer extension and accord well with the bridging theory of flocculation.The dose required for optimal cake moisture is up to three times greater than that required for optimal filtration rate. This effect is reasonably consistent for all polymers studied and appears to be non-linearly dependent on salt concentration, with the difference being small at 0 and 3 per cent but quite significant at 1 per cent.

Jan 1, 1987

By S Shafiee, N Abbate

The evaluation of mining projects requires a methodology that will give flexibility and manage the existing uncertainty within the projects. The discount cash flow (DCF) and other traditional evaluation approaches, which are widely used in evaluating a significant number of mining projects, have simply assumed that the main variables remain constant in their evaluation; elements such as discounted rate, mine life, operating cost and production rate. The DCF ignores managementÆs flexibility to adapt and reforecast and revise decisions. Real options valuation (ROV) is one of the modern evaluation methodologies that provide a tool to adapt and revise mining projects under uncertainty and future variables movements. ROV brings more variables into the evaluation model compared to DCF and assumes them as uncertain and dependent. Finally, ROV provides a range of solutions that can assist in managing this flexibility.This paper endeavours to compare ROV and DCF for mining projects comprehensively and applies these two techniques in the model. The paper shows that ROV will be inclusive of extra value in mining projects due to variables not allowed for, or even ignored, when the DCF model alone is used. One of the significant advantages of the ROV method is being able to evaluate mining projects under different scenarios from the inception of the projects. Furthermore, ROV gives the ability to evaluate the mining project while allowing for abandonment, temporary suspension, or expanding the mining project. In other words, the ROV evaluation process creates an analytical environment, which allows for optimisation of the mining plan within the mining project, as well as the ability to change the capital structure dependant on existing circumstances over the life of the project. The ROV is a new evaluation method that can add value in mining project analysis and offers opportunities to amplify gains, or to mitigate losses. This paper also discusses some of the reluctance to use ROV instead of DCF in current project evaluation.CITATION:Shafiee, S and Abbate, N, 2012. Now, this is the time for mining companies to choose - Real option valuation or discount cash flow, in Proceedings Project Evaluation 2012 , pp 225-234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By C J. Greet, S Jacques

In most instances, the application of high-chrome grinding media results in an increase in the recovery of the valuable mineral(s). The authors have published data from a number of plant-based case studies, which indicate that it is not unreasonable to expect a recovery increase in the vicinity of 1.5 to 2.0 per cent for a copper ore. It is of interest to understand where the increase in recovery is coming from. That is, is the additional copper recovery the result of improved fine particle flotation or is it due to an improvement across all size fractions?This paper aims to answer this question. Laboratory flotation tests were completed using forged steel and a high-chrome alloy on a volcanogenic massive sulfide copper ore. The unsized data indicated that the application of high-chrome grinding media to this ore resulted in an improvement in both copper recovery and copper concentrate grade. A detailed kinetic analysis of both the copper sulfide and gangue minerals was completed that clearly shows that the change to a more inert grinding media produced significant increases in the flotation rate constants (both fast and slow) across all size fractions. It is also possible to observe that the change in pulp chemistry has resulted in a decrease in the flotation kinetics of the -20 micron pyrite, while the coarse pyrite recoveries have increased, presumably because of an increase in the flotation of the chalcopyrite/pyrite composite particles.CITATION:Greet, C J, Jacques, S and Kinal, J, 2014. Recovery-by-size kinetic analysis to determine where metallurgical improvements occur when converting to high-chrome grinding media, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By C J. Greet

Oil can enter a flotation circuit from a number of sources (for example, from mining equipment, oil leaks from the grinding equipment and coatings on the grinding media, but to name a few). Folklore generally states that any oil that contaminates the ore entering the flotation circuit is considered to have a negative impact on flotation. That is, a loss in concentrate grade and recovery.This represents a dilemma for some grinding media suppliers, who use a variety of quenching medium (air, polymer, oil or water) to achieve the desired physical properties of the ball. In the case of high chrome grinding media it is necessary, in some instances, to quench in oil to give the ball the right degree of toughness, which invariably leads to these balls having a thin film of oil on their surface. Once the grinding media arrives on site and site personnel recognise that the balls are “covered” in oil, they generally insist that the oil will have a deleterious impact on flotation performance.Obviously, any supplier “worth their salt” would take remedial action at the point of manufacture to minimise this problem. However, does quenching oil actually present a significant “threat” to the flotation process? This paper provides both laboratory and plant data describing the effect quenching oil has on the flotation of copper sulphide ore, with surprising results!

Aug 8, 2011

By T Ireland, S Eratne, W Newns, P Spies

The approach to risk management during the procurement of major projects often has a significant outcome on the ultimate delivery of a project. The NZ$1.4 B Waterview Connection project is the largest and most complex project yet undertaken by the New Zealand Transport Agency (NZTA) and the procurement process for an alliance contract was refined to provide compliance with the International Tunnel Insurance Group (ITIG) Code of Practice for Risk Management of Tunnel Works (TCoP). The principle of shared risk within an alliance incentivises a common understanding of project risks prior to finalising the alliance agreement and therefore enables superior risk management through design, construction and beyond. Risk management practices need to be instigated well in advance of commercial phases, so that commercial competition does not lead to a significant elevation of project risk. In particular the practice of gaining commercial advantage by taking on a potentially unmanageable level of risk is one of the outcomes to be avoided by the TCoP.During the procurement phase the NZTA placed high value on design and construction mitigation measures proposed in order to address ground risks, as is appropriate for a major tunnel project. In order to achieve alignment on the level of geotechnical risks an Alliance Geotechnical Baseline Report (AGBR) process was developed.This paper describes the measures taken during the procurement process to achieve certainty with respect to outcomes and minimise project risks whilst also achieving value for money. Refinements to the procurement process to ensure compliance with the TCoP prepared by the International Tunnel Insurance Group (ITIG) are described along with the AGBR process applied as part of a suite of measures to achieve a successful procurement outcome.CITATION:Ireland, T, Spies, P, Eratne, S and Newns, W, 2014. Risk management and use of a geotechnical baseline report for a competitive alliance procurement?process, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 553–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

By A Kondratiev, A E. Moiseev

Viscosity of oxide melts is one of the fundamental physicochemical properties that plays a crucial role in important technological and natural processes like slag flow, slag/metal separation, volcano eruptions etc. However, many oxides melt at extremely high temperatures and are highly corrosive in the liquid state, which makes experimental measurement of melt viscosity by traditional experimental techniques a difficult and expensive, if not unachievable, task. In this case it might be useful to employ other methods of viscosity determination such as modelling or simulation. In the present paper the shear viscosity coefficients of selected pure refractory oxides (CaO, MgO, Al2O3 and others) have been simulated at temperatures above their melting points via the classical molecular dynamics and compared to the available viscosity data (eg experimental viscosities, other model predictions) collected by the authors. The simulation has been carried out using the noncommercial molecular dynamics simulation package LAMMPS and the Born-Mayer-Huggins potential, which parameters for the selected oxides were taken from the literature. Several viscosity calculation techniques (the Stokes-Einstein and Green-Kubo equations, the so called Einstein relations, and the non-equilibrium molecular dynamics methods) have been applied to ensure a more reliable viscosity calculation. It has been demonstrated that the simulated viscosity of the selected melts agrees with the available experimental data. It has also been shown that the simulated viscosity of a number of the oxide melts investigated is close to that calculated by phenomenological viscosity models, which supports viscosity extrapolation from the corresponding binaries and ternaries, if no experimental data is present for unary systems. In general, it has been demonstrated that the molecular dynamics simulation could provide a reasonable estimation of viscosity if no other viscosity data is available.

Jun 19, 2024

By R Whittering, C Greet

High chrome grinding media has been used in the mining industry for quite some time, as it often proves economical on a wear basis. However, it is unusual for an operation to change to high chrome solely due to its metallurgical benefits. KagaraÆs Mount Garnet operation made the change from forged steel to high chrome media after laboratory testwork indicated that copper grades and recoveries would improve. The outcome was remarkable with positive changes in pulp chemistry throughout the circuit accompanied by marked improvements in copper, lead and zinc grades and recoveries. Reagent dosage rates were reduced, often by more than half, and the grinding media wear rate dropped to less than a third of the wear rate of the forged steel media. The economic analysis showed that out of the total increase of revenue and savings from metallurgical improvements and reagent and media consumption reductions the metallurgical improvements made up approximately 73 per cent, the reduced reagents saved 25 per cent and the savings through reduced media wear contributing by just over one per cent. This indicates that the popular view of high chrome media only being trialled in the plant for wear economics is outdated and the focus of operations should be shifted to using high chrome media for the metallurgical benefits.

Jan 1, 2006

By L Bergin, D J. Williams, S Islam, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. Once mud has formed, typical handling techniques include its costly removal by mechanical means, or its isolation and capping.There are little data available on the moisture state and shear strength of the capped mud. To investigate the effectiveness of isolation and capping, research has been conducted using a large slurry consolidometer (150 mm in diameter by up to 410 mm in height) to simulate capping in situ. Once consolidated, the mud was subjected to shear strength testing in a direct shear box measuring 60 mm by 60 mm by about 20 mm high. The shear strength of the consolidated mud was compared to that of competent, fresh spoil, a mixture of spoil and mud, and to completely degraded spoil (mud alone).These results have been used as inputs in stability calculations using the commercial computer program Slide 7.0, which demonstrates the strong influence of consolidation of the mud on overall low wall slope stability. The results provide insight into the design and construction of capping to isolate in-pit mud.CITATION:Vangsness, T A, Williams, D J, Islam, S, Smith, A and Bergin, L, 2018. Consolidation and shear strength testing and stability analysis of coal mine spoil degraded to mud, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 97–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

The Marvel Loch Operations (MLO) plant was treating ores from up to six MLO sources and in addition needed to blend externally sourced ores with its own ores. This presented a metallurgical accounting dilemma, which was subsequently addressed by the design, implementation and testing of an automatic sampling system. The MLO automatic sampler was well designed and has been the subject of previous internal and external reviews. The sampling action is fully automated and the unit is essentially self cleaning particularly when sampling primary ores. The purpose of this paper is to document the rationale behind the design, the specific details of the sampling station, its use for ore purchase purposes and an assessment of the sampling system to meet the needs of the operator.

Mar 1, 2010

By H Y. Niu

The coal left in the goaf is easily submerged by groundwater damage. During the mining process of the underlying coal seam, it is necessary to drain the water in the overlying goaf. The coal sample is prone to spontaneous combustion after being soaked in water and air-dried. To explore the effect of micro-functional group transformation of water-immersed coal samples on the spontaneous combustion characteristics of coal samples during the low-temperature oxidation process. Using the experimental method of infrared spectroscopy, the migration law of special functional groups under different oxygen concentrations of water-soaked coal samples was analysed. By means of thermal analysis, the endothermic and exothermic properties of the functional groups in the water-soaked coal samples were studied. The results show that: the higher the oxygen concentration, the more oxygen-containing functional groups in the water-soaked coal sample, compared with the 18 per cent oxygen concentration, the 14 per cent oxygen concentration has a small increase, and the chain length is shortened. The temperature increase together with the oxygen concentration content determines the functional group content, the pyrolysis process produces some functional groups. The lower the oxygen concentration, endothermic rate decreases and endothermic temperature increases, the higher the ignition temperature of coal oxy-combustion, the lower the total heat release, the higher the burnout temperature, and the faster the oxygen-absorbing weight gain and the conversion of functional groups. Below 14 per cent oxygen concentration, the oxidative combustion process will be greatly reduced. The results provide a theoretical basis for preventing long-term water-soaked coal body oxidative spontaneous combustion in shallow buried coal seams.

Oct 12, 2022

By A D. Caccioppoli

Grade control systems within Rio Tinto Iron Ore have proven to be robust, when mining full benches. The Hope Downs 1 operation hosting two Marra Mamba Iron Formation deposits (North and South Deposits) presents a new challenge, where increased mining selectivity due to moderately plunging N-verging folds has made flitch mining necessary in the South Deposit. Poor flitch blasthole sample duplicate results in South Deposit over a 12 month period, compared to North Deposit, have highlighted concerns with grade predictions. In contrast a new grade control methodology (grade splitting) was proposed to alleviate blasthole sampling bias, utilising geological mapping and mineralogical logging, currently practised throughout Rio Tinto Iron Ore Pilbara operations, to estimate theoretical grades for each flitch from a single blast cone assay. To assess this method, reverse circulation holes (RC) were twinned to blastholes establishing an ‘actual’ grade. These blastholes were assayed using current flitch sampling techniques where: flitch positions were estimated, flitch positions were marked with paint, and a full cone sample was taken for ‘grade splitting’. Using these data sets multiple grade predictions were produced, then analysed using Half Absolute Relative Difference (HARD) statistical analysis. In addition to testing these grade control methodologies two other findings were ascertained: an inherent bias in blasthole assays exists particularly in the top flitch, where an average absolute difference of 0.6 per cent in SiO2 and 0.42 per cent Al2O3 was measured; and assays derived where kaolin rich soft shales are intersected were less representative. This is likely to be due to these materials not being properly represented in blast cones. Grade splitting accurately estimated block chemistry, except for a slight under-prediction in Al2O3 and P compared to current grade control methodologies. This method is a viable alternative where grade distribution is stratigraphically controlled.

Aug 22, 2011

By G Stovpchenko, G Jianjun, L Medovar

Electroslag remelting (ESR) today and into the future, will still be the main process for producing high-quality ingots by suppressing segregation, not just refining chemical composition from impurities. This paper analyses state-of-the-art electroslag refining with a focus on ESR with consumable electrodes, and recent technology with liquid metal supply (ESR LM) in view of their refining abilities and development trends, taking into consideration that the size of the ingots required by industry continues to grow, and the composition of new materials sophisticates to withstand increasingly higher mechanical and temperature loads . The yield of suitable metal in large ingots produced by conventional casting is low due to problems of element segregation by height and crosssection. For example, conventional ingots for nuclear powerplant rotors today reach nearly 700 t in weight. Attempts to directly replace such giant ingots with big-diameter ESR ingots weighing approximately 400 t were also unsuccessful because of growing segregation. Modern ESR equipment and technologies produce 200–250 t of ingots of satisfactory quality, reaching 2.5 m in diameter, implementing the change of consumable electrodes during remelting to increase ingot length. Another way to mitigate segregation is to enlarge the smaller diameter ESR ingot by a 500– 800 mm coaxial layer to the desirable diameter by ESR in the current-supplying mould (CSM). Modelling and experiments prove that refining from impurities and non-metallic inclusions at ESR most effectively occurs at the slag bath and liquid metal pool interface because the ESR LM has provided the same desulfurisation. ESR’s special refining capabilities in CSM come from the much longer time of LM residence shown at titanium purification from hard-melting nitride inclusions that are unremovable in vacuum arc remelting (VAR) and electron beam melting (EBM). Implementation of ESR technologies in CSM, especially with LM supply, is prospective to produce heavy enlarged and hollow forging ingots with prevented development of segregation due to dividing cross-section and reducing overheat of solidifying metal.

Jun 19, 2024

By A Parbhakar-Fox, S C. Dominy

The prediction of acid and metalliferous drainage (AMD) from mine waste materials is critically important during all stages of the mine value chain. However, to determine such geoenvironmental characteristics static and kinetic testing of individual waste units must be performed on representative samples. The importance of sample selection cannot be underestimated; it is the single most critical aspect of any geoenvironmental investigation. Poor sampling techniques and inadequate sample selection will contribute to excessive variance, difficulties in interpretation and incorrect assessment. By undertaking mesotextural characterisation based on hyperspectral mineralogical data (with sulfur assay data if available), opportunities to improve sampling strategies are presented. Such data will inform the selection of samples for low-cost total sulfur, paste pH and geoenvironmental logging, which collectively will allow for accurate AMD forecasting and improved sampling practices to be achieved. Once sampled, robust quality assurance/quality control (QA/QC) protocols must be developed where the use of international certified reference standards become obligatory. This is currently not practised, resulting in inter-laboratory discrepancies when undertaking waste classification. Further improvements in geoenvironmental characterisation testing lies in the adoption of blended static testing protocols, whereby blends of waste materials can be efficiently tested so as to give an early forecast as to whether they will produce acidic or metal-laden drainage. Such information is integral in developing a waste schedule that will allow for a non-acid forming waste landform to be constructed right from the start of the operational phase. Ultimately, improvements in this discipline lie in technological innovations with regards to mineralogical characterisation, and by offering geoscience and minerals engineering students a competent education in the discipline. Collectively, this will empower a step-change in AMD prediction and waste handling, and will make the realisation of the United Nations Sustainable Development Goals a reality, rather than a dream.CITATION:Parbhakar-Fox, A and Dominy, S C, 2017. Sampling and blending in geoenvironmental campaigns – current practice and future opportunities, in Proceedings Eighth World Conference on Sampling and Blending , pp 45–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By G Gilchrist, S C. Dominy, T Jashashvili, R C. A Minnitt

The grouping and segregation error is one of Gy’s seven errors that cannot be measured in any qualitative manner because of its transient and changing characteristics each time the sample is handled mechanically. Attempts to calculate the mean and variance of the segregation error is considered by some as ‘an exercise in futility’ that would not help us achieve representative sampling. This research is aimed at understanding the process of segregation of dense, finely divided and dilute particulate materials supported in a clean quartz substrate during intense agitation. Several mixtures of fine-grained materials including steel, tungsten carbide and gold grains were used in these experiments. Four hundred grains of each of the minerals and metals at a top size of 2 mm were mixed with approximately 600 g of finely ground quartz material (95 per cent passing 2000 microns) in a 500 ml plastic jar with a sealable lid. The mineral–?metal mixtures were analysed in three steps using microfocus X-ray computed tomography. Step one consisted of rolling the containers on a flat surface in an attempt to concentrate the mineral and metal grains in the core of the supporting substrate; this is a base case that can be reconstructed after each session of analysis. The second step involved gentle and vigorous shaking of the mixtures in order to segregate the denser minerals and metals from the supporting quartz substrate. In some cases, a third step involved splitting the sample through a riffle splitter. Three-?dimensional images of the surface of each grain, its volume and its X-, Y- and Z-coordinates, before and after intense agitation of the container, were interpreted from the reconstruction of the tomographic X-ray data. The spatial analysis of grains using cell declustering and 3D variography provided a useful means of characterising the distribution of the grains in space and the extent to which they had become segregated during the process of agitation. Spatial analysis indicates that in general, grouping and continuity of grains is weakly developed. The modelled nugget effect remains high for most tests, indicating that grains of similar size did not group together strongly. Agitation through rolling provided the best continuity, although not consistently in the long axis of the plastic jar. The nugget effect was consistently highest, and the range of continuity shortest in samples that had been split, indicating that the grouping and continuity were reduced through splitting the sample. Initial results indicate that very little segregation of the minerals and metals occurs in the quartz substrate. This is somewhat counter-intuitive, but suggests that the effects of agitation on mixtures of dense minerals and metals in substrates of lower density do not lead to excessive segregation. Differences in behaviour between dense materials in response to agitation are evident. Grains of different composition and shape did not group and segregate in a predictable manner in response to the agitation methods. Initial results indicate that the degree to which a material groups and segregates relates more to the characteristics of the denser material itself, rather than the agitation method employed.CITATION:Minnitt, R C A, Jashashvili, T, Gilchrist, G and Dominy, S C, 2017. Quantifying segregation of minerals and metals in particulate materials using computed X-ray tomography and variography, in Proceedings Eighth World Conference on Sampling and Blending , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By A L. de Ambrosis, S J. Clarke, R Bertuzzi, J Redelinghuys

The M2 Upgrade Project involved widening 15 km of the existing M2 Motorway, which is a key route in Sydney’s road network. The Norfolk Twin Tunnels in North Epping convey traffic over a 460 m length of the motorway. The project involved widening the twin tunnels to provide a third lane and breakdown lane in each direction.The widening of the tunnels was fundamentally different to other ‘greenfield’ tunnel projects in that the operation of the tunnel was maintained throughout construction, with motorway traffic permitted close to the excavation faces on a daily basis. The widened works had to integrate with the existing tunnel support, construction details, and mechanical and electrical infrastructure.The existing tunnel afforded the opportunity to review existing ground conditions in the tunnel. Exposures were mapped within the tunnel, and key design parameters were back-analysed from the original monitoring data to provide increased confidence in the assessed impact from the widening works.Traffic capacity of the tunnels was maintained by detailed staging of the works, and included the ability to reopen the tunnels at short notice.A permit to tunnel system was developed to manage the risks associated with re-opening the tunnel to traffic. A comprehensive suite of instrumentation was maintained to provide reliable monitoring data to support this process. Emphasis on the robustness and reliability of tunnel instrumentation provided increased confidence in the adequacy of the tunnel support being installed. The monitoring was routinely compared with design predictions to check the adequacy of the support measures being installed and confirm the design.The approaches and methodologies developed for the widening of the Norfolk Tunnels were effective in maintaining the safe operation of the tunnels throughout the two years of construction, and provide a framework for increasing the capacity of existing tunnel infrastructure in the future.CITATION:Clarke, S J, de Ambrosis, A L, Bertuzzi, R and Redelinghuys, J, 2014. Design and construction for the widening of the M2 Norfolk Twin Tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 591–602 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Readett

The most critical variable in the successful establishment of the Murrin Murrin Heap Leach plant was the effective agglomeration of the Ni laterite ore. This paper describes the test work undertaken to establish the key agglomeration parameters including state of the art testing and analysis procedures. These parameters were then utilised to establish the key design and operational concepts for the world’s first commercial scale Ni laterite heap leach. Following the technical and economic success of the operation, the actual operational data is compared back to the original test work data.

Aug 8, 2011

By Lightfoot BW, Foo KA, Conochie DS

Aberfoyle Limited operated a matte fuming pilot plant, incorporating a SIROSMELT furnace in 1980/81. This plant was a significant advance in both smelting and tin extraction technology. Important design, construction and commissioning aspects are discussed and some of the key points to emerge from this phase of the work are reviewed.

Jan 1, 1984

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015