Search Documents

Swedish sulphide mining is presented. Dry filling is described. Fill properties with and without cement addings are dis- cussed in relation to various studies in la- boratory and in situ.

Jan 1, 1973

By Bof J, Lowe S

BHP's newest colliery on the Southern Coalfield Is Tower Colliery. It is situated near Wilton some 60 kms south west from Sydney. It commenced its operations in 1978 and since that time has experienced considerable roof problems. In its eight years of operations, production has been 936 687 tonnes to December 1985. To a certain extent this is a reflection of the ground control r,,b1cros present in the colliery. paper out Iines the signif mt g,, logical features that are known to exist in the colliery and their influence on roadway development. Faulting has hindered the mine's development and an igneous intrusion has had outhursting associated with it. The prevailing roof rock has also had an impact on the roadway conditions. The paper will look at intersection deformation in present workings. Extensometers have been installed in these areas and provide measurements to verify visual observations. The results show a significant increase in roof movement as the roadway is developed from a single heading, to a T-intersection and then Into a four-way intersection.

Jan 1, 1986

By Szymanski J

In the first part of this paper, the principal sources of dilution during underground evaluation and mining are discussed, then definitions of ore dilution currently in use are analysed. These definitions vary depending on the authors. Ten different analytical expressions of dilution percentage currently exist. It is demonstrated, with the help of a numerical example for a given mining condition, that dilution percentage results vary considerably and that they depend on the definition used. This situation makes it difficult to compare different results regarding the dilution problem, often because some of the terms used are contradictory. A new ore dilution evaluation methodology is proposed, replacing the ten different analytical expressions by only two: the planned dilution factor related to the stoping selectivity, done at the mine planning level, and the additional dilution factor related to the efficiency of the dilution control measures during stoping operations. The conclusion shows that the use of this methodology would be a definitive asset in planning, in stoping operations follow-up, and in future costs comparison studies between mining operations.

Jan 1, 1995

By Schon RW, Stephens CJ

The Whitsunday Volcanics occupy most of the offshore islands from the Whitsunday Group, southeastwards through the Cumberland and Northumberland Groups, possibly extending to the mainland adjacent to Shoalwater Bay, a distance of 370 km. Some of the islands of this group are granitic, but preliminary Rb-Sr data indicate these to represent Permo-Triassic basement. Cretaceous volcanism is interpreted to have occurred during initial rifting prior to the continental breakup of northeastern Australia and subsequent development of the Tasman Basin.The volcanics comprise mainly lithic ignimbrites, with local development of inter-bedded surge and bedded tuff, accretionary lapilli tuffs, lithic concentration zones, and lag deposits. Isolated fluidual rhyolite and dacite domes occur. The deposits are considered subaerially emplaced. A Rb-Sr isochron age for volcanism of 110 Ma is determined from new data. The total thickness of the volcanics is unknown, but a minimum thickness of 4-5 km on Whitsunday Is. is suggested. Eruptive centres are inferred to be distributed throughout the volcanic zone. The volcanics are cut by numerous, dominantly near N-S, dykes ranging from dolerite through to rhyolite in composition.Chemically, the volcanics and dykes exhibit a continuous range of compositions from basaltic andesite, through andesite, dacite, to rhyolite, with minor more alkalic compositions. Phenocryst mineralogy in the silicic rocks is mainly plagioclase, augite, and Fe-Ti oxides, with less frequent quartz and hornblende occurrence. Sr and Nd isoptic compositions for volcanics and dykes are close to mantle values. These data are tentatively interpreted in terms of a lower crustal magma arc source separated from the mantle only a geologically short time prior to Cretaceous magmatism.

Jan 1, 1990

By Hatherly P, Holt GE, McNally G

The current methodology for delineating and subsequently evaluating coal reserves is based on the use of vertical drill holes and surface based geophysics/geology. These techniques have three major problems, these being respectively:-a) Vertical drill holes can only provide a small sample of the coal seam and stratigraphy. Therefore the planar variation in coal reserve and environment parameters can only be approximated.b) Although surface based geophysics has had its fair share of success in recent years, there are still environments which have masked the finding of major structures.c) Access to drill sites is difficult at some locations due to mountaineous terrain, standing water and environmental impact.

Jan 1, 1985

Design of cemented fill in mining is often carried out without any consideration of the structure of the fill. The composition of cemented fills varies in the stopes due to the placement method, and the strength of the fill in the laboratory depends on the density, orient- ation, moisture content and drainage conditions. Within each stope there are definite zones and the structure of both cemented rockfill and cemented hydraulic fill has to be defined for each zone and the field conditions simulated in the laboratory. Structure also affects fill permeability and compressibility. From a study of the cemented fill in place, the effect of changes in the placement methods can be seen and then controlled to improve fill performance and economy. These features of cemented hydraulic fill and cemented rockfill behaviour are discus- sed and illustrated through reference to field and laboratory work undertaken at Mount Isa.

Jan 1, 1973

By Ostrea AM

Aqueous oxidation in an autoclave at ele- vated temperatures and oxygen partial pres- sures is applied to Philippine gold-bearing sulfide ores and concentrates which respond poorly to conventional cyanidation. The gold concentrates are recovered from ores and tail- ings material using the patented OMLI Process (the OMLI Process is able to upgrade tailings material analyzing 0.50 g/t Au to a concen- trate with a grade of 5 g/t Au or better). The results show that with aqueous pre- oxidation of the concentrates ahead of cyani- dation a four-fold increase in gold recovery is obtained compared with straight cyanida- tion. The observed differences in response to the pre-treatment step between various mate- rials are correlated with their mineralogical composition. The chemistry of aqueous oxida- tion is also presented.

Jan 1, 1986

By Lynch AJ, Musgrove NH

The behaviour of chalcopyrite and pyrite in the rougher-scavenger and regrind-retreatment circuits in the Warrego concentrator is discussed. The effects of change in xanthate addition on the separation of chalcopyrite and pyrite is described. The effect of the regrind mill on the (flotation rate of particles containing chalcopyrite and pyrite is discussed with particular reference to the importance of removing sub-mesh particles from the feed to the regrind mill.

Jan 1, 1975

By Hustwick I

New Zealand Steel Mining Limited operates two independent sand mining operations on the West Coast of the North Island of New Zealand. (Fig. 1)Waikato North Head 30km south of Auckland supplies ironsand concentrate as the raw feed for New Zealand Steel's works at Glenbrook, and Taharoa 70km further south, exports ironsand concentrate to Japan. Taharoa uses two sets of six low pressure Warman centrifugal pumps in series to load bulk ore carriers 3km off shore through two underwater pipelines.Waikato North Head delivers the ironsand to Glenbrook l8kms through a 200mm ID buried pipeline using two stages of high pressure positive displacement (HPPD) pumping.A high level of operating and maintenance expertise has been developed since commissioning the two systems which are proving to be reliable, efficient and of minimal impact environmentally.

Jan 1, 1990

By Jensen B, Ofori P, He Y, White E, Stanmore B, Brien M, O&apos

As part of a large AMIRA project, an on-line moisture meter was installed at two mine sites in Central Queensland. This project investigated the factors which control the moisture content of coarse (>0.5 mm) coal from the centrifuges used in conventional coal preparation plants. It was placed immediately after the first centrifuge to isolate the factors pertaining to one machine and its feed.The meter was found to be accurate and precise when compared with manual and mechanical sampling methods. The Grubbs estimator technique indicated that its precision is better than 0.3 per cent at the 95 per cent confidence limit.It has been identified that:1. the variability of the measured moisture contents of coarse coal can be described by normal distributions. Standard deviations of about 0.6 per cent are common; and2. the treatment of the coarse coal on the drain and rinse screens immediately prior to the centrifuge can affect the final moisture content.

Jan 1, 1995

By Thompson IR, Solomons SS

Underground mining with the cut and fill method has been declining during the past decade or so, being replaced mostly by sublevel open stoping methods. During 1983 the Australian Mineral Industries Research Association Ltd. (AMIRA) commissioned a review of the method, with the aim of compiling the state-of-the-art, indicating future trends and recommending topics for research that would be needed to support this future mining. Mines using the cut and fill method in Australia and three other countries were visited to compile current practices and expected developments.Cut and fill is mostly used where geological and ground conditions are unsuitable for open or caving methods. These range from narrow, irregular orebodies to wide, massive orebodies where pillars are retained in ore. There is significant potential for improvement and further development of the method. It may then be used in a broader range of conditions and for orebodies that may not otherwise be viable to mine.

Jan 1, 1985

Western Mining Corporation, managing partner of the Windarra Nickel Project are in- stalling a raise-bored haulage shaft and under- ground crushing system at the Mt. Windarra Nickel Mine. The system will be the second of its type installed by W.M.C., the first being in- stalled at the Otter-Juan mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limi- tations, and escalating costs of a deep decline mine. The Windarra haulage system required a single 3m diameter vertical raise drill hole to a depth of 470 metres. Two five tonne skips in balance will hoist crushed ore and mullock to the surface, at a design rate of 200 tonnes per hour, effectively reducing truck haulage leads by up to 50%. It is expected the project will be in full operation by mid 1982 and will enable the mine to achieve an annual production rate of 600,000 t.p.a. by 1983.

Jan 1, 1982

By Alwan M

At Binebase mineralisation is hosted within an andesitic Neogene volcaniclastic succession on Sangihe Island, Indonesia. Two major alteration types occur; an initial widespread phyllic assemblage of quartz -illite with chlorite, smectite, gypsum and pyrite, and a superimposed quartz - barite - sulphide assemblage. The phyllic alteration arose from a neutral to weakly acidic hydrothermal solution of greater than 200 degrees C, and the quartz - barite - sulphide assemblage arose from a cooler slightly more acidic fluid. This second alteration event is interpreted to have selectively replaced permeable volcaniclastic breccias and coarse lithic tuffs within the altered sequence. Gold and silver mineralisation is associated with the latter alteration, and is locally controlled by the degree of silicification and sulphide abundance. The sulphides present are pyrite, covellite and chalcopyrite. The sulphides are very fine grained with colloform and framboidal textures and were deposited contemporaneously with the bulk silicification of the coarse sediments. A large portion of the mineralised rock has been oxidised to a quartz - barite -limonite - goethite - jarosite assemblage.Coincident gold, silver and antimony geochemical soil anomalies gave the best correlation with anomalous gold and silver grades in bedrock as identified by drilling. Resistivity proved a reliable geophysical method for delineating zones of silicification.

Jan 1, 1990

By Takeuchi T, Matsugaki K

We have developed a new shotcreting which is suitable for the primary support of TBM tun- nelling in soft rock. This spraying compound is made from cement, a special accelerating agent and glass fiber. It can be sprayed on to a rock surface using a specially designed gun similar to paint-spraying equipment. Some of the characteristics of this method are as follows: 1) If spraying is done keeping the distance between the gun and the rock surface be- tween 0.2 and 3.0 m, the rebound losses are small and there is little dust. 2) This method can be used on excavated rock surfaces under inflowing water conditions of up to 10 i/m2òmin. 3) After 1 day the compressive strengthes of the sprayed material is greater than 250 kgf/cm2.

Jan 1, 1987

Structural geological information is widely used at the Mt Whaleback Mine, Newman, WA. Recent improvements in the structural understanding of Mt Whaleback are providing a very cost-effective way of reducing geological risk, improving the economics of mining, optimising pit design and addressing safety problems. The structure of the Mt Whaleback orebody is highly complex and has a significant influence not only on iron ore genesis but also on pit wall stability. A team approach between the Structural Geology and Geomechanics Groups has been providing excellent results to reduce geological risk at Mt Whaleback.

Jan 1, 1994

By Boyd D. M

Minor magnetic anomalies which may be un represented on a magnetic contour map can be extracted from the original survey data and plotted by the described method to provide a rapid interpretation of the magnetic survey, provided that the data has been recorded digi- tally on magnetic tape. The example used comes from 40 kilometers south of Charters Towers, Queensland.

Jan 1, 1977

By Hayward SB

The Maragorik prospect is an example of high sulphidation, Cu/Au mineralisation occurring at a high level in the hydrothermal system. As extensive ash deposits blanket the region, controlled-source audio magneto-tellurics (CSAMT), in conjunct-ion with bulldozer trenching, have been used to delineate subsurface geology. Fluid upflow has occurred along EW structures dilated by rotation on the bounding major NW lineaments. Rising hydrothermal fluids have exploited permeable horizons in contact with the upflow structures. This lithological control is evident as ledges of silicification and peripheral clay alteration, at high levels in the system. As is typical of high sulphidation systems, a two phase fluid consists of an initial rapidly moving vapour-dominated phase, followed by a liquid-dominated phase. Much of the zoned and overprinted silica to clay alteration is developed from the vapour-dominated fluid. Mineral deposition occurs as a result of brecciation of the competent silic-ification by liquid phase fluids. Such mineralisation is of restricted volume in ledges proximal to the feeder structures.The style of alteration and mineralisation are indicative of a very low temperature and hence a high level system. Thus, although high sulphid-ation systems are inferred to develop from porphyry-related magmatic fluids, such a source at Maragorik is interpreted to be very deeply buried.

Jan 1, 1994

I am very pleased to be here at this seminar on carbon-in-pulp (CIP) technology for the extraction of gold as I am always interested to hear about any new development in any aspect of gold ore processing. We can expect to learn a great deal from the papers to be presented over the next few days. It is not my purpose to give a detailed description of the CIP process nor to give a complete historical review. However, in this opening address it was thought appropriate that I should mention some historical features and some technical factors to set the scene for subsequent papers. HISTORICAL NOTE Table 1 shows some interesting dates of the use of carbon in gold metallurgy in Australia. Mount Morgan used carbon after chlorination TABLE I Carbon precipitation in Australia 1891 Mount Morgan 1917 Yuanmi mine (Edmunds) 1934 Sons of Gwalia (Edquist) 1975-1980 Various pilot plants and small companies 1980- Various large and small plants

Jan 1, 1982

The Northwest Territories (NWT) of Canada has emerged as a major new province for diamond mineralisation in less than three years. This is primarily the product of a diligent search in the form of a scientifically based exploration effort. However other factors, including positive aspects of the business and the legal environment have also been identified as assisting the exploration process. In my view these have increased the likelihood of diamond mining becoming a major new industry for Canada. The supportive role of various government agencies has been important. In addition, the character of many of the joint venture deals that have been done has provided an attractive setting for the capital intensive evaluation and development work that is now required to bring the diamond discoveries into production. Perhaps of equal importance is that with the recognition that is being given to the success of the NWT diamond ventures, Canadian explorers are continuing to attract new risk capital for further exploration. This paper attempts to model and quantify the probability of exploration success translating into successful mine development.

Jan 1, 1994

By Rigby D, Gould K. W, Hart G. H

The variation in chemical and isotopic composition of hydrocarbon gases generated from humic source rocks in the Cooper Basin, the orth West Shelf, the agoorin oil shale deposit. ollinsville and the southern Sydney Basin is reviewed, discussed and interpreted.The primary composition of gases generated in and released from such source rocks appears to be very largely controlled by the degree of dispersion of the organic material. For example in eoaly shales, where the degree of dispersion may be high, products as generated may escape into surrounding inorganic structures where further maturational reactions may proceed. On the other hand, when the organic materials occur in massive form, as in coal seams, the hydrocarbons generated tend to be retained within the coal. Further cracking to the stage of methane generation is usually required before release of hydrocarbon products is significant.Secondary factors of importance in determining seam gas composition in the Bowen (Collinsville) and southern Sydney Basins are the invasion of coal measures by carbon dioxide from external magmatic sources and/or the vertical diffusion and loss from the surface ofgases generated at depth.Isotopic measurements of gas composition have been particularly valuable in determining the origins and histories of the gases examined, in demonstrating when gases are of mixed origins and in the prediction of gas quality in exploration.

Jan 1, 1985