Search Documents

By Claude Bazin, Patricia Obiang

"The slurry density (pulp percentage of solids) and the size of the grinding media are often used for the optimization of an operating ball mill. In many cases a change of ball size is made at the slurry density used with the original ball size. But is the optimum slurry density changing with grinding media size? Laboratory grinding tests were conducted to answer that question and results indicate that more than likely there is no need to adjust mill slurry density when adjusting the size of a grinding media in a ball mill. Full scale behaviour could be different because slurry density affects the slurry transportation through the mill and the classifier operation.INTRODUCTIONOre preparation begins with a fragmentation step that liberates valuable minerals or exposes mineral surface to the environment. The size reduction step of a mineral processing operation is energy demanding and the optimisation of this process should always be an objective for the plant metallurgists. Various approaches could be considered for improving the operation of a grinding circuit. For a close grinding circuit an adequate tuning of the classifiers operation may lead to substantial savings (McIvor, 1988). Once a grinding mill is in operation, few variables remain to be considered for process optimization. The ball charge is usually maintained to achieve a target power drawn by the grinding mill motor. The rotation speed is seldom considered (McIvor, 1983; Bazin and Lavoie, 2000) as a change of mill speed usually implies a costly pinion change. If the liner and lifter configuration is critical for SAG and AG mills (Latchireddi et al., 2005), few discussions are available for ball mills (Fuerstenau and Abouzeid, 1985; McIvor, 1983). The mill feed size distribution can also be adjusted but this implies changing the upstream processes, which transposes the optimization process to another level. Modification to grinding media shape is a possible avenue (Cooper et al., 1994), but it remains that slurry density and grinding media size are probably the most frequently considered variables for the optimization of a ball mill."

Jan 1, 2007

By D. B. Dreisinger, M. Rasouli

"Developing technology to address the environmental hazards associated with selenium in mine-impacted waters has been a serious challenge. Ion exchange (IX) has been identified as a potential treatment technology. This paper begins with a review on selenium adsorption with commercially-available basic anionic exchangers (BAS). It then looks at the use of resins for selenium removal via modification with the addition of -O, -N, or -S-containing chelating ligands and chelating polymeric ion exchangers pre-loaded with immobilized metal cations. The synthesis of chelating exchangers requires a final product with a highly stable metal in the ligand-metal complex. The nature, oxidation state, size, and affinity of the metal for the target oxyanions and the size, degree of protonation and space configuration of the oxyanion are among critical factors affecting the oxyanion uptake. There is a limited number of studies on the critical parameters affecting the selenium affinity for chelating exchangers. Such a study could fill in the gaps of our understanding of selenium-metal-chelating ligand interactions and assist in developing a new ion exchanger. In addition to commercial IX resins, layered double hydroxide materials (LDH) have received attention for oxyanion removal from waste water. The adsorption capacity of the LDHs are affected by the crystallinity of LDH, the nature of metal components, the ratio of metals, charge and type of anion, and the space between the layers. In particular, the Friedel phase (FP), a member of the LDH family, showed high adsorption capacity for selenate removal from synthetic solution. A study is currently underway at the University of British Columbia to investigate the effect of different synthesis methods and aging on the suitability of FP for selenium removal from mine waste water."

Jan 1, 2017

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By R. L. Bailey

"The Acheson D-3 Pool was discovered in August 1950, and contains 88 producing oil wells on 40 acre spacing. Initial oil-in-place was 118 million stock tank barrels and initial well potentials averaged 2,000 barrels per day.In early 1956 studies of hydraulic interference between the Acheson and Leduc D-3 Pools were conducted on the Carter Petroleum Reservoir Analyzer. These studies indicated that the natural water drive to Acheson would be incapable of replacing reasonable withdrawal rates over the life of the pool. To avoid shrinkage losses a scheme of pressure maintenance by water• injection was therefore instituted in March 1957.This pressure maintenance scheme is notable because pressure is being effectively maintained by high volume injection through one well located on the flank of the pool. Close control on reservoir behaviour is maintained by regular bottom-hole pres-sure surveys and observation of water cuts on producing wells. No evidence of pressure gradients or channelling of the injected water has been observed to date, and the water-oil contact has remained level over the whole field. It is possible to control the average reservoir pressure within very close limits by varying the rate of fresh water injection.Ultimate recovery estimated from the rise of the oil-water contact and calculated water influx to December 31, 1958, is 335 barrels per acre foot, or a total of 91.4 million barrels from the pool. This compares to 217 barrels Per acre foot or a total of 59.4 million barrels indicated from laboratory test data."

Jan 1, 1961

By Guoqiang Lan, Jun Song, Bin Ouyang

Rare-earth pyrochlores, commonly exhibiting anomalously low lattice thermal conductivities, are considered as promising topcoat materials for thermal barrier coatings. However the structural origin underlying their low thermal conductivities remain unclear. In the present study, we investigated the phonon properties of a group of RE pyrochlores, Ln2Zr2O7 (Ln = La, Nd, Sm, Gd) employing density functional theory and quasi harmonic approximation. Through the relaxation time approximation (RTA) with Debye model, the thermal conductivities of those RE pyrochlores were predicted, showing good agreement with experimental measurements. The low thermal conductivities of RE pyrochlores were shown to largely come from the interference between the low-lying optical branches and acoustic branches. The structural origin underlying the low-lying optical branches was then clarified.

Jan 1, 2015

By Ivor da Cunha

Ontario Mining Association (OMA) represents 57 members that are engaged in exploring, producing & processing mineral resources in an environmentally responsible manner. Conservation Bureau at the Ontario Power Authority (OPA) develops, coordinates and stimulates commitment to electricity conservation and demand management programs ? OMA selected compressed air optimization for high impact cost savings and energy efficiency potential ? Ontario Power Authority (OPA) provided $218k funding for $532k project ? Commenced summer 2006, Final Report June 2007 ? Three representative sites participating: ? Williams, CVRD Inco & FNX McCreedy ? Different levels of energy management ? Small, medium and large mining operations ? Different corporate practices and culture

May 1, 2007

By Scott G. Honan, Wayne F. Luinstra

"Since 1992, the concentration of gold using gravity methods has progressed to become an important part of production at Hemlo Gold's Golden Giant Mine. Currently, the gravity circuit accounts for approximately 25% of the Golden Giant Mine's Gold production. This circuit consists of a 30 inch Center-Drain Knelson Concentrator and a Shaking Table. The evolution of gravity concentration will be discussed with an emphasis on the economic justification for a gravity circuit as well as the practical aspects and metallurgical impact of operating such a circuit. It will be demonstrated that the operation of a gravity circuit has definite benefits to the operation of the Golden Giant Mill and will continue to play an important role in future gold production.1.0 IntroductionHemlo Gold Mines Inc. Golden Giant Mine is a 3000 TPD underground gold mine and milling facility located 40 km east of Marathon, Ontario. Mining is accomplished by means of sublevel longhole open stoping. The ore is processed using conventional crushing, 3-stage ball milling, conventional cyanidation and CIP processes. The mill and concentrator are described in more detail in other publications1,2.Since July of 1992, the Golden Giant Mine has been using a gravity circuit for gold recovery in the mill's grinding circuit. Despite the fact that gold recovery averages over 96% using conventional cyanidation and carbon-in-pulp processes, the gravity circuit has become an integral part of milling operations. This paper will discuss the economic justification for a gravity circuit as well as the practical and metallurgical aspects of its operation."

Jan 1, 1996

By Derek H. C. Wilton

"The Nain Province (NP) of northern Labrador is a >600 km long by =100 km wide Archean craton that has undergone relatively little mineral exploration until economically signifcant concentrations of orthomagmatic nickel sulphide were discovered by Diamond Fields Resources (DFR) at Voisey’s Bay. Due to the great time span between crust formation andfnal intrusive activity (ca. 3.9 Ga to 1.27 Ga),there were, however, numerous metallogenic events within the NP.The NP was intruded by the ca. 1.3 Ga to1.2 Ga Nain Plutonic Suite (NPS) composite anorthosite-granite complex. The NPS dividesthe NP into the southern Hopedale Block (90 km by 150 km) and the northern SaglekBlock (375 km long by =50 km wide). These two blocks appear to represent two distinct Archean cratonic nuclei, each with its own distinct metallogenic history. The NPS is a coalesced assemblage of composite intrusions which include anorthosite, troctolite, norite, gabbro and granite.The Hopedale Block contains the Hunt River and Florence Lake greenstone belts, and the Weekes Amphibolite which represents remnantsf the older Hunt River greenstone belt. Geologically, these belts have some potential to host komatiitic Kambalda-style nickel, volcanogenic massive sulphide (VMS) and meso -thermal lode gold mineralization. The unconformity between Paleoproterozoic cover sequences and the trondhjemite-tonalite-granodiorite (TTG)suite which engulfed the greenstones was the locus for lead-zinc-bearing quartz-carbonate veins. Minor fracture-hosted uraninite showings are also present in the TTG.The Saglek Block is a high-grade gneissterrane with deformed Archean supracrustal sequences but no greenstone belts. Within the gneiss are variably-sized enclaves that range in composition from anorthositic to ultramafic; some of these latter xenoliths contain abun-dant fuchsite. There are also three small anorthositic to ultramafic meta-igneous complexes present in the gneiss near Okak Bay.Some Archean meta sedimentary and maficgneiss supracrustal sequences contain iron-oxide and sulphide members. The sulphide-bearing Tasiuyak parag neiss defines the cra-tonic suture between the NP and Churchill(Rae) Province. Along the cratonic suture between the NP and Churchill Province from Ramah Bay north are remnants of the Archean(or Paleoproterozoic) Hutton Anortho site Suite. Ultramafc layers within the suite contain chromite and elevated Ni values.Three ca. 2.0 Ga supracrustal sequenceswere deposited in small fault-bounded basins within the NP. The Snyder Group contains pyrrhotitiferous massive sulphide horizons. TheMugford Group contains SEDEX-like massive sulphide blocks in a debris fow and ultramafic sills with unusual PGE concentrations; alaskitic granite cutting basement gneiss to the group contains stockwork-like pyritiferous quartz veins. The Ramah Group contains numerous MVT-style zinc-lead sulphide occurrences.The Reid Brook Intrusion of the NPS contains enormous and high-grade nickel-copper-cobalt massive sulphide bodies at the Voisey’s Bay deposit. Exploration in the northern portions of the NPS in 1995 has indicated the presence of other potentially economic nickel sulphide horizons."

Jan 1, 1996

By Dale A. Sketchley

The objective of Quality Assurance and Quality Control programs on advanced exploration projects is to ensure that data from sampling, assaying, and recording of geological observations are of high integrity for the purpose of obtaining reliable mineral resource and reserve estimates. National Instrument 43-101 Standards of Disclosure for Mineral Projects states that all scientific and technical reports must be prepared and certified by a Qualified Person in accordance with professional and industry standards following Mineral Exploration Best Practices Guidelines and Definitions, and Guidelines of the CIM Standards on Mineral Resources and Reserves. Additional information is given in Companion Policy 43-101CP and Technical Report Form 43-101F1. Although the Qualified Person must discuss and describe the Sampling Method and Approach; Sample Preparation, Analyses, and Security; and Data Verification; there is little specific information in the guidelines on Quality Assurance and Quality Control programs. Examples from the Oyu Tolgoi Cu-Au Project are given for optimizing sampling protocols, following proper sample preparation procedures, safeguarding sample shipments through chain of custody, ensuring quality of assaying with Round Robin monitoring programs, verifying transcribed data, and validating data with check assays to ensure high integrity for resource and reserve estimation. Oyu Tolgoi, also known as Turquoise Hill, is in the South Gobi desert, Mongolia, about 550 km south of the capital city of Ulaanbaatar, and 875 km northwest of Beijing, China. The project covers a major copper-gold system, which consists of the South West, South, Central, and Far North deposits, comprising high sulphidation and porphyry mineralization with oxide, supergene, and hypogene ore types. Exploration is done by multiple diamond drill rigs, and samples are prepared on-site and shipped to laboratories in Mongolia, Canada, and Australia for further preparation and analysis.

May 1, 2003

By Karl Hoover, Cassandra Spence, Brent Bachewich, Jaakko Levanaho

"Since year 2000 the gold recovery into copper concentrate at Hudson Bay Mining and Smelting has reduced considerably during the summer months. This initiated a testwork program in the fall 2003 to find reasons and solutions for such change. During the testwork mineralogical factors, water quality effects and different reagents were evaluated. The reason for the lower recovery appeared to be the sensitivity of some collectors to pulp temperature. As a result of the work different collectors are being used in the mill in the summer than in the winter. A modification to the water system was also made to provide cooler water to the mill in the summer months.INTRODUCTIONHudson Bay Mining and Smelting (HBMS) is located in Northern Manitoba, just on the border of Manitoba and Saskatchewan. The complex consist of four different mines, Callinan, Trout Lake, Konuto Lake and 777 mine including copper smelter and zinc hydrometallurgical plants producing metallic copper and zinc. Gold is a very important byproduct providing about 30% of the mine revenue. In early 1990s when the company was facing declining ore reserves and was starting to gradually close down the operations, the 777’th exploration drill hole discovered a new orebody, which initiated a $0.5 billion expansion program. The main projects were a new 777 hoist with underground development and a new zinc cell house. About $30 million was used to increase the mill throughput to the present 2.27 million tonnes or 2.5 million short tons per year. The expansion programs were finished by the end of the year 2003.Historically the gold recovery at HBMS has varied between 60 and 70%. The recovery has been somewhat lower during the summer months. Gold recovery improvement projects were conducted throughout the 1990s, but were not focused on the seasonal gold recovery variance. However, since 2000, when the water system modifications to meet the increased water demand were completed, the gold recovery during the summer has been much lower than in the past. In August 2003 gold recovery fell below 30%, which initiated a metallurgical research program to discover the reasons behind the low gold recovery in the summer."

Jan 1, 2005

By T. Yalcin

"This paper describes the development of a mathematical model for determining the liberation of an ore at various grinding sizes, based on the combined results of microscopic counting, grinding tests, and chemical analysis.The method is illustrated with an application to the magnetite ore of Sherman Mine in Temagomi, Ontario. For this ore, a degree of liberation of 98.7% was determined at a grinding size of 90% passing 44 microns, which closely corresponds to the final grinding size employed at the Sherman Mine Concentrator.Introduction Liberation characteristic of ores have direct and significant bearing on overall economics of concentration processes.Target grades and recoveries can be achieved only it minerals are adequately liberated prior to separation. Degree of liberation depends on the extent of size reduction. However, due to the high costs associated with size reduction processes, it is important to keep size reductions within limits of satisfactory liberation. Prevention of excessive size reduction is also necessary because of inefficient mineral separations in very fine sizes. Hence, a study of reduction size — liberation relationship is essential for optimum profit from milling operations.A number of procedures have been developed for liberation studies (1-12), but there is lack of method for universal adoption.A new approach is presented in this paper that might provide a realistic estimate of liberation and give a practical guidance as to the degree of size reduction required for satisfactory liberation."

Jan 1, 1985

By A. F. Brock

Introduction During the past ten years, shaft sinking has been going on continuously at Inco and new shafts and shaft extensions have been sunk under a broad diversity of conditions. The Murray mine and the Stobie section of the Frood-Stobie mine have?been opened and a main hoisting and supply shaft has been sunk at each of these mines; No. 2 shaft at Murray was sunk initially from surface to 1,960 feet and is now being extended; No. 7 shaft at Stobie was sunk from surface to 3,105 feet. No. 2 shaft at Garson has been extended from 2,200 feet to 3,200 feet in depth. At Levack, No. 2 shaft is being extended from 1,860 feet to 2,850 feet for ore hoisting from the 2,650 lev el. At Creighton, No. 6 shaft, collared on 52 level, was sunk 1,740 feet to a total depth of 5,563 feet below surface. It is the deepest Inco working. At Creighton, also, No. 7 shaft is being sunk from surface to the 30 level to handle the ore from caving operations. Ail Inco main hoisting and supply shafts sunk during the past twenty years have been vertical rectangular shafts equipped with two cages and two ore skips. The cages are standard and interchangeable for all shafts except Garson No. 2; they are single-deck, 13 ft. 4 in. by 5 ft. 2 in. inside and are designed to carry a maximum material load of 16,000 lb. The man load is 48 men. Skip capacities at the several shafts vary from 8 to 15 tons. Forty-two hundred feet bas been established as the standard vertical lift, and the permanent hoisting equipment at each shaft is designed for eventual hoisting from that depth.

Jan 1, 1950

By C. Stamberg, W. McGuire, R. C. Carlson, L. W. Vollmer

"The selection of materials and pre-cautionary measures for handling natural gas and condensate containing aqueous hydrogen sulphide are presented. Based on the results of a pilot production test and laboratory studies, together with several years . of operating experience, it was found that the behaviour of materials in sour gas environments can be predicted sufficiently accurately for engineering purposes.The selection of proper materials is essential for preventing sulphide-stress cracking. Where high strength materials are not required, low car-bon steel is used. Components requiring high tensile strength and hardness characteristics should be made from K-monel or properly heat-treated carbon-manganese-molybden-um and AISI 4140 steels. Welded connections are a potential source of sulphide-stress cracking. Consequently high quality welding and strict inspection are suggested as the most economical precautionary measures available.A maintenance program based,. where possible, on visual inspection of equipment and/or test spools located at strategic points should be used to follow weight loss and putting corrosion in sour gas environments. If severe weight loss or pitting corrosion is encountered, inhibitors have been found to be an effective deter-rent."

Jan 1, 1960

By P. Kostuik

"Recent interest in the pipeline transport of solid mate-als has been sparked by the idea that, in an inflationary onomy, pipeline costs are more stable than the costs of any other transport systems. Pipelines have proved over 1e years to be dependable, records indicate that main-•nance and operating costs are comparatively low, and 1eir amenability to automation is of considerable im->rtance.The concept of hydraulic hoisting of solids from under-round, or cross-country hydraulic transportation of con-~ntrates and ores, is currently of prime interest to the ining industry. In general, this paper deals with a preliminary investi-ation of energy losses incurred while transporting a rela-vely heavy, crushed mine product, namely magnetite, oth vertically and horizontally. The basis and validity of everal equations derived by other experimenters to com-ute these losses is discussed. A theoretical analysis of ydraulic hoi:,,ting is made, and, based upon test results, calculation of horsepower requirements for hoisting an re under a given set of conditions is presented. Results indicate that:n vertical transport, the friction head losses are identical to those of clear water, and the total energy requirement for hydraulic hoisting then becomes a function of height of lift, concentration and specific gravity of the solids being hoisted. .-In horizontal transport, friction head losses can be calculated with reasonable accuracy using Bonning-ton's correlation curve. Losses computed utilizing Durand's correlation (K = 85) result in estimates which are too low by 10 to 30 per cent, an<l those calculated using Newitt's correlation (K = 1,100, K = 66) give friction loss values which are too high by 10 to 30 per cent . . -The theoretical horsepower (RMS-hp.) required for hoisting hydraulically is approximately half of that required for conventional double-drum skip hoisting."

Jan 1, 1966

By Tsuyoshi Adachi

Photovoltaic (PV) system is especially taken notice as one of important renewable energy resources, because PV has potential to provide a certain amount of energy supply as well as without greenhouse gases emission. Considering recent rapid increasing demand for PV system, more expansion of PV system is expected in the future. However, some precious metals and minor metals such as silver, indium and others are used as component materials of solar cell in PV system. Even if energy supply would become renewable, strict limitation of these metals still remain because amount of natural resources and recycling of metals has restrictions intrinsically. The aim of this study is to reveal the possibility of materials supply restrictions for Photovoltaic system quantitatively and to propose several measurements to assess supply risks for materials. Especially, silver supply potential which is used as wire line in PV system as well as PV demand forecast to estimate material use in the future are focused on. We divide underlying supply risk into 5 measurements and analyze them by time series, i.e. price volatility, resource potential, recycling ratio, production type and supply concentration are investigated. Comparing these factors of silver with other metals, the potential of silver supply for PV is presented. In addition to it, we propose another method to quantify country risk applied an insurance pricing model in finance pricing theory and combine it with the supply concentration measurement. As a result, supply risk of silver will increase gradually in the near future because of its resource constraints and supply-demand balances although silver market is sufficiency competitive one. From the country risk analysis, Peru is not only a significant supply country but also has the highest country risk. Some higher risk countries will increase the level of supply risk even if the concentration ratio of supply indicates moderate level.

Aug 1, 2013

By George W. Bain

Summary During the last three years the discovery of gold in the belt of volcanic and sedimentary rocks extending eastward from the Porcupine and Kirkland Lake gold-fields has caused a great deal of excitement in mining circles. The area is heavily drift covered, and every aid to the location of veins is eagerly grasped. A knowledge of the physiographic history of the area is of the utmost importance in the application of many of these aids. Evidence is presented to show that glacial erosion has lowered the general elevation very little below the pre-glacial level, and that many glacial erratics have been carried less than three miles southward. Probably a knowledge of the general geology of a: region was never more necessary to the understanding of the distribution and continuation in depth of the mineral veins than in this area. Four distinct granites occur in the region, and gold-bearing veins are genetically associated with only one of these. Two types of quartz-feldspar porphyries have been found, only one of which has any bearing on the locus of the mineral veins. Many other examples of this complexity of associations might be cited, but everyone goes to show that in most cases the economic importance of the deposits can be realized only after the regional geology is understood. A series of sandstone, limestone and shale intruded by granite lies unconformably below the Keewatin lavas. The latter are intruded by a gneissoid granite and are overlain unconformably by the thick series of Timiskaming greywackes and silts. These are intruded by carbonated syenites and syenite porphyries which have since been rendered somewhat schistose.

Jan 1, 1927

By D. S. Case

"Following a brief explanation of the land arrangements under the Alaska Native Claims Settlement Act, this paper will examine both a mineral exploration agreement and a mining development agreement negotiated between two large mining companies and two different Alaska Native institutions. One of the institutions is a village corporation involved with an exploration agreement and the other is one of the Alaska Native regional corporations, which is party to a mining and development agreement with Cominco Alaska for the development of the Red Dog lead and zinc mine.Special attention will be given to the factors to be considered when dealing with small aboriginal owners with few resources in the context of an exploration agreement, including development issues which must be considered early in the process. The paper will also discuss the unique royalty and taxation structures developed for the Red Dog Mine Agreement as well as environmental issues. The paper will also consider the ways in which the cultural and differing economic interests of an aboriginal owner and a large mining company have been accommodated in the both the exploration and development agreements"

Jan 1, 1998

By M. Myllymäki

"Pre-treatment of mill feed in a minerals processing plant enables for higher production efficiency per ton of product, reduction of consumables and diverting mineral feed types. Sensor based particle sorting allows for pre-concentration of the run-of-mine (ROM) material prior to other concentrating process. Various sensors provide different responses from the minerals in measured particles. The capability of “accepting” or “rejecting” particles based on sensor responses is investigated in specific test work for each project. Modern sorting machines use pneumatic actuators to divert the reject particles from the material stream. This paper discusses the incorporation of ore sorting test work in processing and plant design. When taking the effects of a sorting circuit into account early in the process planning phase, the downstream process can be adequately sized and impacts evaluated. Potential benefits include but are not limited to increased head grade, lower tonnage to the mill, increased mining operations, removal of deleterious elements and changed properties in the process feed. In a case study we present the Keliber lithium project in central Finland. The plant will produce 9000 tons of lithium carbonate per year from a spodumene ore. Ore sorting and flotation tests were carried out in laboratory and pilot scale. Process models were designed and simulations performed using Outotec’s HSC Chemistry Simulation software. Changes in the flotation performance (grade, recovery, impurity levels) were simulated with and without the pre-concentration of the ROM material. The metallurgical performance and mine economics of the different operational scenarios were evaluated using the Ore-Met optimizer module of the simulation software.INTRODUCTION Challenges in the recent years such as declining ore grades, increasing energy prices, scarcity of water and increasing environmental regulations raise the demand for more efficient processing technologies. Sensor based sorting offers a method for pre-concentration or waste rejection at an early process stage. The technology analyzes each rock particle separately for their unique physical and chemical properties, and diverts the particles into separate material streams by high pressure air jets. Successful implementation relies on ore heterogeneity, differential sensor response and suitable feed preparation."

Jan 1, 2018

By W. G. Johnson

"As we move into 1983, Canada is not only in a deep recession, there are major changes taking place.International competition is growing fiercer.Major core industries such as automobile, steel, mining, oil, agriculture, forestry, fishing, major manufacturing and others are just not expanding.If and when recovery comes starting in mid-1983, as many predict, don't expect industries to suddenly resume former growth patterns. It's just not possible.Companies, by necessity, are becoming lean and mean, and they are still in the process of reducing staff to meet changing times and conditions. Many of the staff now being released may never return to fulltime work with a single employer, particularly if they cannot measure up to more exacting performance standards and management expectations.There are clear cut instances of people who lose a job for reasons beyond their control. A merger, the loss of function, or a major reorganization sometimes creates casualties of people who were excellent performers. Such people can survive well, based on the tongue of good report and with some help from associates or others. However, even good performers often have difficulty in adjusting to the rigors of finding a new job and to become their own personal salesman."

Jan 1, 1983

By S. Yadav, T. G. Murthy, C. Saldana

"An experimental study has been carried out in order to study the deformation of porous brittle materials under plane strain indentation. Gypsum, which is well known model system for understanding the behaviour of soft rocks, is used in this study. The effect of wedge angle is investigated in this research through this series of experiments, using wedges of 3 different apical angles. High-speed, high-resolution images are captured using a CMOS camera during the experiment. The images obtained are analyzed using a Particle Image Velocimetry (PIV) algorithm in order to obtain the evolving velocity, strain-rate and strain fields.INTRODUCTIONThe problem of indentation, which is usually referred to in the context of hardness testing is ubiquitous as a material characterization technique for a large class of solids. Mechanical properties of materials such as yield stress, flow stress, fracture toughness, elastic moduli etc. can be related to the hardness of a given solid. The indentation problem involves a given material or solid (whose properties are to be determined) indented by a relatively harder material (indenter) allowing the solid to undergo plastic deformation, which is then related to the yield stress of the material. The problem of indentation and its variants see many applications ranging from mining and petroleum industry, infrastructure industry, manufacturing, and biomedical sectors. Indentation has been extensively studied in metals, with accurate measurement of deformation parameters, stresses and comparison with analytical solutions. On the other hand, understanding of indentation in other class of solids such as cellular solids, porous solids, rocks, and soft solids is still nascent. In case of rocks, a comprehensive understanding of the indentation problem is very crucial because of the obvious applications in mining, petroleum and infrastructure sectors. The inherent porosity, the brittle nature of the rocks, adds to the complexity of indentation in these porous brittle solids. Various theoretical models with degrees of simplifying assumptions have been proposed to study the indentation in rocks. The most common model used in the study of indentation in rocks is a cavity expansion model, wherein a blunt indenter indenting into a rock is approximated with the expansion of cylindrical or spherical cavity in an elastic-plastic material. Complementary studies in understanding fracture initiation and propagation due to indentation has been largely based on the studies of traditional brittle materials such as glass."

Jan 1, 2015