Search Documents

By C. T. Christensen

The paper gives an outline of the design, installation and performance of a series of mooring and berthing dolphins for a major ferry berth outside the port of Elsinore, Denmark. The Dolphins are large cylindrical bottle shaped and open ended steel piles vibrated into the sandy seabed. They are subsequently equipped with prefabricated fender units. Vehicle access to the ferry is via a fixed ramp and a semi-submerged linkspan. Supplementary passenger access is via a covered gangway steel bridge from an existing gangway facility to a midship door in the ferry«

Jan 1, 1989

By V. M. Troughton

Further pile load testing has been carried out at Canary Wharf to compare the performance of base grouted and ungrouted bored piles founded in the Thanet Sand. The testing regime included three preliminary test piles and two working test piles. The results of these tests are summarised in Table 1 below. Two of the preliminary test piles were located only 14m apart to compare the performance of a base grouted and ungrouted pile in similar ground conditions. The load/settlement behaviour of these two preliminary test piles are compared on Figure 1. All the piles were drilled under bentonite with a drilling bucket. In the base grouted piles four grouting tubes were placed with the reinforcement cage to within 500mm of the pile toe. After the pile had been concreted these grouting tubes were then extended to the pile base by drilling and packers were installed. Grout was then injected into the four tubes simultaneously.

Jan 1, 1991

By Sridhar Krishnan

This paper presents the results of a comprehensive pre-production pile testing programme for the US$ 800 million 1400MW Coal-Fired Jimah Power Plant Project in Negeri Sembilan, Malaysia. The testing programme included high-strain dynamic testing and fully instrumented static axial and lateral load testing of driven prestressed concrete piles and bored cast-in-place piles. A highlight of the testing programme was the pioneering use of the Global Strain Extensometer (GloStrExt) Method, a deformation monitoring system that uses advanced pneumatically- or hydraulically-anchored extensometers and a novel analytical technique to monitor loads and displacements down the shaft and at the toe of driven prestressed concrete piles. The experience with the testing programme for the Jimah Project also demonstrates the possibility of achieving notable breakthroughs, not only in the monitoring, evaluation and reporting of pile foundation behaviour dynamics but also in our understanding of the mechanisms that underpin such behaviour. These significant gains are undeniably a direct result of the committed and co-operative relationship among the project owner, design/builder, specialist piling subcontractors, pile suppliers and pile instrumentation and testing specialists.

Jan 1, 2006

By Louis Donolo

New buildings in today's urban environment, especially in down-town areas, invariably involve the construction of multiple level basements. Used for parking, storage and commercial space, these underground structures normally extend 30 to 50' and more below grade and, to make optimum use of expensive land, they usually occupy the full site right up to street/sidewalk and property lines. SOIL SUPPORT SOLUTIONS Building these basements requires vertical excavation, and consequently, a temporary soil support system which will eventually be replaced by the permanent foundation walls of the structure.

Jan 1, 1987

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By P. B. Kelleher

Most of the piers and other pile-supported marine structures in the New York City Harbor area were constructed prior to the widespread use of currently available pile protective systems. As a result, the support piling of many existing marine structures have experienced deterioration to an extent that their structural sufficiency is impaired long before the useful life of the structures they support is over. This situation presents special and unique problems of how to restore the structural integrity of these piles while at the same time allowing full use of the structures they support. Spearin, Preston & Burrows is a 100 year old New York City-based marine construction firm specializing in waterfront and foundation construction. In recent years it has undertaken and successfully completed several unusual projects in the New York City Harbor area involving the rehabilitation of existing, deteriorated piling underneath major, economically important marine structures. This work was accomplished using techniques that permitted full use of these structures. Several different pile rehabilitation systems were used, each having their own particular application to the deterioration problems of the piles supporting each structure.

Jan 1, 1989

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By Larsson Lars-Erik, Rani Isa, Martin Jönsson, Håkan Bredenberg, Mats Larsson

"IntroductionSteel Core Piles are used extensively in Scandinavian countries, where hard rock is found within reasonable depths. A steel core is cast into a drilled steel tube casing and a rock hole is extended below the casing. This pile type is considered a very reliable type of pile, and for urban environment it has several advantages compared to other types of piles. One critical phase of the installation is the drilling of the casing. Usually a DTH (Down The Hole) hammer is used. Drilling in fine grained soils, e g silt, below the ground water level, may give rise to an excessive volume of soil material flushed up from the point of the casing, resulting in unacceptable settlements around the pile installation area.Using a new method for drilling of the casings, the ELEMEX-method has proven to significantly reduce the risk for such problems. In the paper a case record from a ground improvement project in central Stockholm is described. Ground settlements around the drilling area were carefully monitored over a longer period. Both the new drilling method and the conventional DTH casing drilling method where used, so that the corresponding ground settlements could be compared. Settlement records and comments are included in the paper.The paper also gives a description of the project. The installation of new piles and foundation constructions cover a whole city block in Stockholm downtown. The reason for the replacement of the old, damaged wooden piles were due to their destruction caused by a long time lowering of the ground water table. The paper gives a description of the new drilling method as well as an overview of usual urban foundation issues and their solution in Sweden, Finland and Norway.Drilled Foundation MethodDrilled Foundation, using drilling methods originally developed for drilling of large diameter rock holes, is today a standard method for the installation of piles, tiebacks, drilled pile walls and other foundation components, especially in urban built up areas where other techniques as drop hammers, augers, vibratory hammers and other equipment fail to meet the requirement, se ref(1). Drilled foundation is for example used for"

Jan 1, 2014

By M. A. El-Sohby

The paper describes some problems encountered with the foundation of a deep drainage caisson constructed on the Nile Bank in Cairo. The use of suction dredging while sinking the caisson led to a piping failure of the sandy soil in the base which was loosened during the process of pumping. A study was carried out to investigate the problem and a procedure was adopted to retain the stability of the caisson.

Jan 1, 2010

By D. G. Bishop

This paper is intended as a review and update of the use of Pressure Injected Footings as deep foundation units in North America. We will discuss various aspects of this pile and then discuss a particular project - the Mobile Alabama Convention Centre which is currently under construction. Pressure Injected Footing is a generic name used to describe a foundation unit that has been in use around the world for some 80 years. It has been used on all types of structures. It is an excellent pile in both compression and tension. It is particularly economic where a layer of granular soils can be found at relatively shallow depths. Other types of piles would penetrate these layers. Caissons are often difficult to construct in these soils because of their lack of cohesion and the often present water table. PIFs can density these shallow layers and carry relatively heavy building loads on them.

Jan 1, 1992

By David C. Lager

While not a new construction technique "top/down" construction is seeing increased use in high rise building construction. Using diaphragm wall, drilled shaft and mining construction techniques, top/down construction enables construction of both the below grade basements and high rise structure simultaneously. To date the top/down method has been used on at least four major building projects in the United States. This paper will review the economic, engineering, construction and schedule issues associated with top/down technology on two projects -Olympia Centre, Chicago, and One Westwood, Los Angeles. Top/Down construction is currently under consideration on several additional projects in the United States.

Jan 1, 1987

By Tomohide Takeyama, Yuki Yoshida, Masaki Kitazume

"Abstract A series of centrifuge model tests was conducted to investigate the failure pattern and stability of cement treated clay ground having an unsupported vertical slope. The model ground was subjected to monotonically increasing centrifugal acceleration until it failed due to the enhanced self-weight. The test results were compared with the numerical analyses in which the treated soil was simulated by the Smoothed Particle Hydrodynamics (SPH) method. In the simulation, the Dracker- Prager model is employed as the constitutive model. In order to simulate the brittle behavior of the cement treated soil, it is assumed that the unconfined strength is gradually reduced to a certain value which corresponds to the residual strength due to accumulated plastic strain. It was found that the simulation by using SPH method can express the brittle failure observed in the centrifuge model tests.IntroductionBecause of economical and environmental concerns it has become more difficult in recent years to obtain enough soil to construct reclaimed land for airports, electric power plants, manufacture plants and so on. On the other hand, it has become difficult to find and construct disposal sites for waste subsoil or dredged soil. These circumstances have encourage geotechnical engineers at present to use these poor quality materials as filling materials more than they were used one or two decades ago. Several soil admixture methods have been developed to improve their properties and to manufacture high quality fill materials.The deformation and strength characteristics of cement treated soils have been investigated in Japan, which have revealed that the treated soil is characterized by a brittle behavior with quite high compressive strength and quite small strain at failure, and the treated soil with relatively high strength shows tensile failure instead of shear failure. Regarding to evaluate the stability of structures adjacent to or buried in the treated ground, Kitazume (1998) and Kitazume et al. (2003) investigated the earth pressure of cement treated ground by the centrifuge model tests. And they emphasized that the failure pattern of the cement treated ground was much different from that of ordinary ground. After the Hyogoken- Nambu earthquake in 1995, many design codes for the seismic stability were revised in Japan, so that seismic stability must be evaluated more precisely. The dynamic earth pressure of ordinary grounds is usually calculated by a pseudo-static limit equilibrium method based on the Mononobe- Okabe’s method (Okabe, 1924; Mononobe and Matsuo, 1929). This calculation method is also applied to the cement treated ground, although its applicability has not been thoroughly clarified."

Jan 1, 2014

By William G. Ryan, David S. Graham, Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"The St. Croix River Crossing project on the Minnesota-Wisconsin border has been in the process of planning and public debate for two decades, with several changes in alignment. During the course of the earlier planning process in 1995, a drilled shaft load test was performed to obtain preliminary design information. There were some difficulties in maintaining stability within the weak sandstone bearing formation, and the measured axial resistance was relatively low. Subsequent experience by the Minnesota Department of Transportation with similar weak sandstones on the I-35W project suggests that improved construction techniques using modern drilling fluids may offer opportunities for improved performance. During final design in 2012 a second load test program was performed of a full scale test shaft constructed using polymer drilling fluids. The stability of the socket excavation in the weak sandstone appeared to be greatly improved and the measured axial resistance significantly higher.This case history illustrates the excellent performance that drilled shafts can provide in even relatively weak sandstone bedrock as well as the profound influence on axial resistance associated with the construction techniques used. The improved resistance values obtained by the new load test with more recent construction technology allowed the foundation scheme to be substantially optimized with respect to the number and size of required drilled shafts, reducing the size, cost, and risk of the coffercells and footings.IntroductionThe Minnesota Department of Transportation (MnDOT) has awarded the first phase of a bridge construction project that will cross the St. Croix River between Oak Park Heights, MN and St Joseph, WI. The first phase construction contract involves building the river pier substructures including groups of drilled shafts beneath each tower leg. A general location of the bridge project is provided in Figure 1.Prior to award of the construction contract, two separate design-phase axial load tests were performed on non-production drilled shafts with rock sockets. Both tests were static, bottom-up tests using the Osterberg Cell (O-cell). The first test was performed in 1995 when final design and construction was thought to be imminent. After years of public debate and literally, an act of Congress, design of the project was finally restarted and a second load test performed in 2012. The 1995 test was conducted on the Minnesota bank approximately 900 ft southwest of the St. Croix River bank. The 2012 test was conducted in the river about 2,100 ft northeast of the1995 test location. A plan-view of the project indicating the test program locations relative to the bridge alignment is provided in Figure 2."

Jan 1, 2015

By A. Boominathan

The behaviour of single piles under lateral dynamic loading is very critical and the study is still a current field of research since 1950's. Though many methods have been developed analytically to estimate the dynamic lateral stiffness, very limited dynamic testing on full scale piles were carried out to study the response of piles under lateral dynamic loading. Hence, field lateral dynamic vibration tests are conducted on driven precast concrete square pile of 400mm size and driven cast in-situ concrete piles of 400mm and 500 mm diameter at a petrochemical complexes site at Haldia (India). The results of steady state and free vibrations tests are discussed herein and compared with the response of the piles estimated from PILAY.

Jan 1, 2002

By Chris D. Shewmaker

So you want to install 2,600 augered cast-in-place piles, about 155,000 lineal feet, in 33 working days? It can be done. The Public Service Enterprise Group (PSEG) decided to build a combined cycle power plant in Lawrenceburg, Indiana. PSEG selected Fluor Constructors Indiana, L.P. to design and build the plant. Fluor Constructors, in turn, selected Richard Goettle, Inc. to install the piles. The initial plan was to install the 2,600 piles in 33 days, working six (6) ten hour days per week. After successfully installing and performing four pile load tests - up to 300 ton capacity - we set out to complete the work and meet the aggressive schedule. After three weeks of installing an average of 75 piles a day with three drill rigs, Fluor relaxed the schedule because we were so far ahead of their projected construction sequence. We elected to continue drilling on a ten-hour day, five days a week schedule. In all, we installed nearly 2,800 piles, totaling 175,000 lineal feet, in about 47 days.

Jan 1, 2004

By David E. Albus, Ahmadreza Mortezaie, Bidjan Ghahreman

The structural evaluation of seismic performance of an existing hospital in Long Beach, California, required spring constants of foundation elements. The structure included support by deep foundation elements comprised of belled (underreamed) caissons. The available relationships in the governing building code (ASCE41-13) to compute axial stiffness is not applicable due to the belled configuration of the caissons. The large diameter of the bells required consideration of the foundation medium to the axial stiffness; a detail not clearly described in ASCE 41-13. Furthermore, prescriptive equations in ASCE 41- 13 used to estimate lateral stiffness only consider pile groups with the assumption that the only source of lateral stiffness is the axial reaction of individual piles. These assumptions were invalid for the project at hand where all caissons are configured as single foundation elements, not a pile group. In the present work, the approach taken to estimate seismic stiffness of single-belled caissons is described which accounts for the elastic behavior of the foundation medium below the bell base and lateral behavior of single-pile shafts. Results of the work provide a more satisfactory derivation of the spring constants consistent with current modeling methods. INTRODUCTION Seismic evaluation of an existing hospital in Long Beach, California, required geotechnical investigation followed by site-specific ground motion analysis. This evaluation was required by the Office of Statewide Health Planning and Development (OSHPD) in order to meet the requirements of the Structural Performance Category 4D (SPC-4D) published as a part of the 2016 California Building Code, CBC (Section 3412A). SPC-4D utilizes ASCE41-13, as modified by OSHPD, and involves two seismic performance objectives: BSE-1E (20% probability of exceedance in 50 years) and BSE-2E (5% probability of exceedance in 50 years). Spring constants and capacities of foundation elements were needed for evaluation of the structural performance of the building subjected to these two performance objectives. Our review of the as-built foundation plans indicated that both shallow footings and caissons were used for support of the structure. The plans demonstrated that all caissons are belled (under-reamed) and are individual, i.e. not part of pile groups. In this paper, the subject site condition and foundation elements are described first. This is followed by details of assessing spring constants and vertical capacities for belled caissons. The new requirements of the 2016 CBC concerning the evaluation of critical facilities will likely entail evaluation of other structures with belled caissons due to the more extensive use of these foundations in the past. This paper proposes a method to address the conditions of individual belled caissons not explicitly considered in the current code provisions.

Jan 1, 2018

By Jean Balech

This paper presents some results of dynamic loading tests performed on concrete piles driven in soft clay formation. The load transfer mechanism, measured in the dynamic increasing energy test (DIET), under blows of growing energy, is described in terms of mobilized normal forces diagrams and unitary local friction and displacements. It was observed that the lateral skin friction grows up to a maximum, in the soft clay layer and, gradually diminishes to a residual value when the system presents the maximum mobilized resistance. It may be concluded that the rupture load is not equal to the maximum mobilized point resistance plus the maximum mobilized local friction as suggested by most of static bearing capacity formulae.

Jan 1, 2002

By Donald A. Bruce

The paper reviews aspects of the construction and performance of prestressed ground anchors installed in soils and weak rocks. Attention is focused on good practice for drilling, tendon fabrication and handling, grouting, stressing and testing. Regional variations - not always logically justified - are described. The performance of anchors in a variety of geological conditions is illustrated with reference to recent full scale test programs. 1. Introduction In the United States there has been steady growth in the use of prestressed anchors in materials other than competent or hard rock, in the years since their introduction in the late 1960's. This expansion has to a large extent been driven by specialty geotechnical contractors who both imported foreign developments and conducted their own basic researches, in locally prevailing conditions. With such data and experience, these engineers have had the confidence to promote "alternative solutions" for difficult earth support problems to receptive designers and owners. In turn, being engaged in the details of design and performance monitoring has given these parties the close exposure necessary for the real transfer and understanding of the technological concepts, and this knowledge has generated positive feedback for the contractors.

Jan 1, 1991