Search Documents

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982

By W. P. Yant

Canister-type gas masks Pave become an essential part of the equipment of many industries, not only for use in .emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau bas become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By S. R. Borrowman

This investigation by the Bureau of Mines was undertaken to develop information on the extractive metallurgy of thorite ores because potential ore bodies of this mineral have been found recently in Colorado, Idaho, and Montana. Basic information on thorite ore treatment that would be useful in appraising the potential of these and other domestic thorium resources was developed. The work was done mainly on thorite ore containing 3.87 percent ThO2 from the Powderhorn district, Colo., and on a composite sample containing 0.52 percent ThO2 from the Wet Mountains district, Colo. Limited tests of d corroborative nature subsequently were made on a sample containing 2.30 percent ThO2 from the Lemhi Pass area on the Idaho-Montana border.

Jan 1, 1962

By Martin Hertzberg

This Bureau of Mines study concerns the use of the tube bundle method as a sensitive and reliable detector of mine fires. The method involves the pneumatic, sequential sampling of many points in a system through branching tube bundles that lead to a single analytic station of high sensitivity, good reliability, and convenient location. Two serious limitations inhibit its use: the relatively slow response times for long lengths of narrow sampling tubes and the wall-diffusion losses for submicrometer smoke particulates. These limitations were quantitatively evaluated by measuring tube transit times and smoke particulate transmissions as a function of tube length, diameter, and pressure drop. The comparison of the data with theory offered the challenge of extending the classical, incompressible flow solutions to the two compressible cases: isothermal and adiabatic. New equations were derived for these cases, and the measured transit time data gave reasonable agreement with calculated solutions in both the laminar and turbulent regimes. The measured transmission losses of smoke particulates from several combustion sources compared favorably with those expected from Brownian diffusion losses to the interior walls of the sampling tubes. Traveltime and smoke transmission graphs are provided and, pump power requirements are estimated.

Jan 1, 1976

Objective: On-the-job training (OJT) is a common means of training workers. By definition, it seems relatively simple. However, to be effective, training must go beyond the simple process of following an experienced worker around the workplace— sometimes called the "follow Joe" method. NIOSH researchers spoke with human resources personnel, safety and health specialists, supervisors, experienced miners, and new miners and found that OJT was of high interest, but was rarely part of a formal or standardized program. Various training methods have evolved to ensure that a trainee will absorb the information presented rather than simply emulate what the instructor is teaching. These methods have been brought together into a published guide for developing an effective formalized OJT program. The guide (Information Circular (IC) 9479) is called "Coaching Skills for On-the-Job Trainers." It contains materials and suggestions for your company or mine to conduct a 1-day workshop for teaching OJT trainers how to be better coaches to less experienced workers. The guide was created by the NIOSH Pittsburgh Research Laboratory and a safety professional from a private mining company.

Feb 1, 2006

By Walter W. Kaufman

This report summarizes a study conducted to determine the state of the art of various rock removal systems and their capabilities. The objective of the study was to determine if currently manufactured equipment can adequately accomplish rock removal in surface mine reclamation applications. Evaluations of state reclamation regulations, with regard to topsoil rock content, were made to determine the rock removal requirements. The major categories of equipment studied are rock pickers and rock rakes. The impact of rock removal implementation on the reclamation operations is discussed in detail.

Jan 1, 1979

By Donald R. Corson

The effects of adding varying amounts of type I portland cement to hydraulic backfill are described. Six different fill materials, each with three cement contents, were tested to determine which fill properties have the most significant effect on cemented strength. Two strength prediction equations, based on the physical and mineralogical properties of the fills, were formulated, and these accounted for 96 and 99 percent of the variability of the data. Results of both unconfined compression and triaxial tests of cemented fills are given, and the effects of moist curing and fill densification on the 7-day strength are discussed. Permeability test data are given, and the decreased permeability due to cement content and curing time is shown graphically. A discussion of the limited evaluation of other potential stabilization additives (expansive cement, fly ash, sodium silicate, gypsum, and asphalt) is included in an appendix.

Jan 1, 1970

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to ma e these questionnaires as complete as possible.

Jan 1, 1963

By H. C. Fuller

Rhodonite, a manganese silicate, occurs as an important component of extensive veins in the San Juan district of Colorado. Recent work by the Bureau of Mines has demonstrated that typical ores of the area can be upgraded to about 30-percent manganese content. Because of their siliceous nature, such concentrates require further processing to convert the manganese into more usable forms. The investigation described in this report demonstrates the technical feasibility of producing silicomanganese from a rhodonitic concentrate by electric smelting methods. The rhodonitic concentrate used in the smelting research was prepared by dry high-intensity magnetic separation of ore from the Silver Queen vein. The concentrate contained 29 percent manganese, 2 percent iron, and 41 percent silica. The principal minerals in the concentrate were 35 percent rhodonite, 30 percent rhodochrosite, and 25 percent quartz and chalcedony. Limestone was used as the flux and coal was used as the reductant. These minerals were crushed and screened to minus 1/2-inch plus la-mesh size.

Jan 1, 1962

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By Eric E. Cather

Approximately 270,000 cu yd (20[0],000 cu m) of inferred subeconomic auriferous gravel resources were estimated in three Tertiary deposits in the Polk Springs study area (fig. 1 and table 1). These resources are exposed between tuff-breccia and lava flows of the Pliocene Tuscan Formation and Paleozoic or Mesozoic metamorphic rocks which suggests that although no deposits were identified in the other RARE II areas, they may be concealed beneath the Tuscan Formation. Difficulty in choosing drilling targets will make the likelihood of resource discoveries small. The development and production of these deposits would also be prohibitive under current economic conditions due to the thick covering of volcanic rocks. Recent stream gravels of Deer Creek in the Polk Springs study area contain enough gold to attract gold hobbyists; however, the stream gravels do not have sufficient volume to be considered a resource. Potential exists for additional auriferous gravels near the Occidental Mine in the Polk Springs RARE II area.

Jan 1, 1983

Provide improved permanent stoppings designed specifically for use in mines with large cross-sectional entries. Approach The large entry sizes in many mines, such as oil shale, salt, and limestone, make the conventional stopping construction techniques used in smaller opening mines unacceptable. The Bureau of Mines and Colorado Mining Association jointly sponsored a contract to design and test new or modified stopping concepts for these mines. The most promising concepts were then tested in an oil-shale mine having 30-foot-high by 55-foot-wide mine entry openings. All stopping designs tested were evaluated in terms of cost, air tightness, and resistance to blast damage.

Jan 1, 1987

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to make these questionnaires as complete as possible.

Jan 1, 1963

By C. W. Morris

This study was performed for the U.S. Bureau of Mines. An existing computer simulation of a dragline was modified to simulate a dragline dumping into the hopper portion of a cross-pit conveyor system. This revised computer model was then used to study four proposed cross-pit conveyor systems. Parameters such as dragline position, hopper position, and digging procedure were varied to maximize the dragline production. This performance was compared with the conventional side-casting spoil method. I t was concluded that the cross-pit conveyor systems were competitive with the conventional side-casting technique.

Jan 1, 1977

A mobile vacuum sweeper to remove loose coal and coal dust from underground coal mine workings was designed, built, tested, and evaluated. The design was based on an extensive test program. Pick up and conveying rates vs. air volumes, velocities, and nozzle shapes were determined for coal rubble in a laboratory pneumatic handling system. A gas/solids separation system was developed and tested in the laboratory capable of separating the solids loading from the vacuum system air stream to the very high degree required to preclude degradation of the ambient (mine) air. Two designs were made, one for belt conveyor and one for general district cleanup. The belt cleanup machine was chosen for test and demonstrated in an underground coal mine performing cleanup work in belt haulageways and on ribs.

Jan 1, 1975

By I. Liebman

The Bureau of Mines conducted experiments on coal dust explosion suppression. The investigation took place on a beltway in the double-entry of the Bureau's Experimental Mine. Using conditions that simulate those in a working mine, the investigation showed that a coal dust explosion can be readily initiated in a conveyor belt entry. Also, the explosion can spread into adjacent entries through opened crosscuts (stopping destroyed by explosion) to propagate for long distances even though the adjacent entries are rock dusted in compliance with regulations. Passive water barriers (water-filled tubs) were found to be effective in suppressing explosions on a beltway; however, barrier efficiency was reduced by opened crosscuts. The study indicated that the beltway barrier should be the distributed type consisting of continuous rows of water-filled tubs covering long distances along the entry. A plan is outlined for the installation of a water barrier system in a working coal mine for the protection of a beltway.

Jan 1, 1981

By J. S. Dunning

One Federal Bureau of Mines research goal, to minimize requirements for domestically scarce mineral commodities through conservation and substitution, can be accomplished by utilizing more abundant elements such as iron, molybdenum, and titanium. An example of this research is the study of precipitation-hardening, iron-base alloys containing molybdenum and titanium, as substitutes for the high-tonnage stainless steels that are high in imported nickel and chromium. The precipitation hardened iron-base alloys are strengthened by a dispersion of the ternary Laves phase, Fe2 (Mo, Ti). Aluminum and chromium additions changed the solid solubility limits of molybdenum and titanium in a-iron and affected the composition of precipitating phases. A baseline composition of Fe-7Mo-2Ti was selected to study the effects of aluminum and chromium additions on the precipitation-hardening mechanism and microstructure and was also used in studies of mechanical properties and oxidation resistance. The study yielded workable, precipitation-hardening alloys, with elevated temperature strengths equivalent to or superior to types 304 and 316 stainless steels. Chromium and aluminum additions in combination were more effective in providing oxidation resistance than either addition was alone.

Jan 1, 1980

By C. H. Fisher, Abner Eisner

"INTRODUCTION Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils 4 such as gasoline, kerosene, and neutral oils from coal—tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 60 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin—free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin—free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water—soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiatingbetween cyclic (naphthenes) and acyclic hydrocarbons (paraffins). Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons,It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings."

Dec 1, 1937

By J. A. Kost

The contract objective was to evaluate the effectiveness of available dust-control technology for double-drum shearers. Eight underground surveys were conducted to evaluate drum design, drum spray nozzle locations, ranging-arm sprays, water quantity, wetting agents, and cutting techniques. The final report is made up of eight dust-control technique reports, each discussing, details of the individual mine surveys.

Jan 1, 1985

By C. A. Rhoades

The spillage that accumulates under conveyor belt lines presents a possible fire and explosion hazard fomiinqjetsoruiel, especially to those who must clean up the spillage. The U.S. Bureau of Mines conducted research to reduce this hazard by identifying and investigating the parameters affecting the efficiency of conveyor belt cleaning. The amount of material carried back under the conveyor and the wear rates of metal cleaning blades decreased with increasing blade-to-belt pressure to a limiting value, after which the carryback and wear rates remained essentially constant. The optimum blade-to-belt pressure was found to be 11 to 14 psi for the research conveyor system. Greater pressures increased the blade-belt friction without improving either cleaning or blade life. The modes of blade wear were three-body abrasion and slurry erosion caused by the sand-lime test mixture. Wear rates were reduced by increasing the metal hardness, opti-mizing the pressure, and removing conveyor belt imperfections. Corrosion was not observed to affect the wear of various steels in tests of less than 34 h. The results of this study should allow mine operators to run their conveyors under conditions that will maximize cleaning and minimize equipment wear.

Jan 1, 1989