Search Documents

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By L. J. Defferding

This report documents the work performed by Battelle-Northwest and its sub-contractors in Phase I of a project to develop a cross pit conveyor system for the Bureau of Mines. The conveyor system description includes details of the conceptual design as well as system and component specifications. The selection of primary and back-up sites for system demonstration is discussed. Maneuvers and operating sequences required for mining the selected demonstration site are described and illustrated in detail. Economic viability of the cross pit conveyor system was analyzed by estimating the cost of overburden removal per ton of coal using the Battelle-designed concept and comparing these costs to the cost of an available state-of-the-art 30-yd3 dragline operation. Testing and trade-off studies conducted are documented and the results presented. Alternate designs considered in developing the selected cross pit concept are included for completeness. Based on the evaluation of the selected concept, it was concluded that the cross pit conveyor system proposed by Battelle is a technically and economically feasible overburden handling method with a good potential to improve western coal mining efficiency.

Jan 1, 1976

By M. E. Tyrrell

To promote greater use of abundant domestic raw materials in the manufacture of synthetic mullite, the Bureau of Mines has undertaken a comprehensive investigation to determine the effects of the impurity oxides TiO2, Fe203, and alkali on physical properties of sintered mullite-forming mixtures. The first part of the report presents the results of work covering a major area within the mullite study; namely, the effect of impurity oxides on volume stability, one of the outstanding characteristics of mullite refractories. The volume stability of 20 compositions in each of 3 alumina- to-silica ratios, which blanket the range commonly found in purchase specifications, has been determined following procedures of Navy Specifications B-15606 A for Grade A high-alumina refractories. Results indicated that so long as 5 percent of impurities are combined approximtely in the proportions of 3 percent Ti02, 1 percent Fe203, and 1 percent alkali, sintered mullite-forming compositions in the almina to silica range tested will be volume stable. A permissible tolerance of one-half per- cent in each impurity oxide provides a range that includes values common in the natural minerals from which sintered mullite may be made. Within the total range of 5-percent impurity mixtures, a greater number of volume-stable compositions were obtained by increasing the alumina-silica ratio.

Jan 1, 1962

By Eric E. Unger

Results are presented of a census of the machines used in surface coal mines in the United States. The numbers of each machine type and model reported to be in use are tabulated for large and small mines in the Eastern, Central, and Western regions. Also tabulated are the average daily usage times of the major machine categories and the numbers of machines that have acoustical and other cabs. Projections of the total numbers of primary production machines are given. It is found that heavy tracked dozers and wheeled front end loaders constitute the most prevalent machine types, and that generally a very few models of machines made by one or two manufacturers constitute a major fraction of the population in each machine category. About 70 percent of all machines are reported to have some kind of cab, and about half of these are reported to be acoustical gabs; it is noted that acoustical cabs generally came into significant use since about the early 1970's. It is observed that the percentage-wise mixes of equipment types used in the various categories of mines differ significantly for only a few types of machines, notably for heavy dozers and loaders, and for haulers, highway trucks, and internal-combustion engine-powered shovels and draglines.

Jan 1, 1977

By R. V. Higgins

This paper describes a method and a computer program for calculating shape factors and areas of channels that turn more than 90° and conduct fluids into the backs of wells. The program represents an improvement over a previous Bureau of Mines investigation by using a 4-point Lagrange interpolation equation instead of a 3-point and by summing areas of trapezoids with either x altitudes or y altitudes. Some of the techniques reported in this paper can also be used to compute the areas between contours and the lengths of lines that turn more than 90°.

Jan 1, 1968

By C. M. St. John

A series of analyses of possible mining excavations associated with the development of copper nickel deposits of the MINNAMAX site in Northeastern Minnesota is presented. Specific areas such as roof and pillar stability and excavution orientations are addressed. The majority of these analyses were conducted using a boundary element method but some cases were also analyzed using the finite element method. Comparable results were obtained using the two methods but the boundary element method required less data preparation time and computer run time. Results of the analyses, as well as indicating the capabilities of geotechnical numerical models, provide some insights into behavior around multiple excavations in jointed rock.

Jan 1, 1979

By Lars Skogsberg

Work with hand-held power tools can be found in most industries all over the world. This type of work exposes the operators to different kind of loads like gripping-forces, feed-forces, exposure to vibration and noise, holding hot or cold surfaces and the exposure to dust. Designing a power tool with good ergonomics is a matter of finding the best compromise. As a simple example, increasing the mass is not acceptable because it will increase the forces needed to handle the tool. At the same time increased mass will in most cases reduce the vibrations. Vibration disorders related to the use of hand-held power tools has been known and reported since long. It is therefore essential that low vibrating tools are developed and used. The new vibration regulations in Europe, based on the Physical Agents (Vibration) Directive, have put increased focus on the vibration control in industry. Forces acting on the tool cause vibration Tools for industrial use must be of very robust design to withstand the very hard use they are exposed to. Industrial tools are therefore normally designed with the main parts made of metal. From a vibration point of view this means that most tools can be regarded as rigid bodies, especially because the dominating frequency normally is equal to the rotational frequency of the tool spindle or the blow frequency for a percussive tool. These frequencies are with few exceptions below 200 Hz. Handles however can not always be regarded as rigidly connected to the tool. There are several examples of weak suspensions designed to reduce vibration transmitted to the hands of the operator. There are also examples of designs where the handles just happened to be non-rigidly connected and in some cases even in resonance within the frequency region of interest. Oscillating forces act on the tool and the result is vibration. Design principals In all cases forces are the source of vibration. This leads to the three basic principles to control vibration: • Control the magnitude of the vibrating forces. Examples are the balancing unit on a grinder or the differential piston in a chipping hammer. • Make the tool less sensitive to the vibrating forces. Examples can be when the mass of the guard on a grinder is rigidly connected to the tool to increase the inertia of the tool. • Isolate the vibrations in the tool from the grip surfaces. Examples are vibration-dampening handles on grinders or pavement breakers, the air-spring behind the blow-mechanism in a riveting hammer or the mass spring system in a chipping hammer.

Jan 6, 2006

By R. M. Creamer

Attempts have been made to electroplate titanium and zirconium from aqueous, nonaqueous, and fused-salt electrolytes. Metals were produced only in fused-salt electrolytes, the major product being sponge metal. All other electrolytes gave only partial reduction of the metal ions. Fused alkali borate electrolytes containing titanium salts gave titanium boride powders and coatings of poor adherence. Some of the problems encountered in the deposition of these metals and some of the aspects of titanium and zirconium chemistry involved are discussed. INTRODUCTION Titanium and zirconium are both relatively light, noncorrosive metals with both military and civilian uses. This has led to intensive investigations into the metallurgy of these metals. Both metals are high in the Electrochemical Displacement Series and are difficult to prepare in a pure state. At present they are prepared by reducing their chlorides, using magnesium. Electrolytic reductions have resulted in the preparation of fine powders or sponge of variable quality. It is believed that a good process of electroplating these metals on a baser metal would result in a very desirable product. The objective of the research summarized in this report was to investigate methods of electrodepositing these metals, with the idea of producing uniform, coherent plates. Most of the work was concentrated on titanium, the more abundant of the two metals. A system developed for titanium should be applicable to zirconium owing to their chemical similarity. Information gained from these experiments may also be applicable to the electro-winning of the metal.

Jan 1, 1954

By David D. Hottinger

Only a minimum amount of illumination is generally provided for many types of mobile surface mining equipment. This condition presents a hazard to operating personnel working on and around such equipment. To reduce this hazard MSHA has proposed safety regulations requiring minimum levels of illumination for hazardous zones on and in the immediate area surrounding surface mining equipment. This report describes a Bureau of Mines sponsored project demonstrating the feasibility and effectiveness of providing dragline illumination in compliance with the proposed MSHA regulations. A description of the computer aided design, on site installation and field evaluation of individual lighting systems for each of three different size draglines is presented

Jan 1, 1981

By William W. Adams

A larger measure of safety attended the operation of the stone quarries and related plants in the United States during the calendar year 1935 than in any other year for which annual records are available for the industry. The accident rate, covering fatalities and nonfatal injuries that disabled an employee beyond the remainder of the day on which the accident occurred, was 38.19 per million man-hours of work performed. The nearest approach to this favorable record was in 1932 when the rate was 38.48. The rate for 1934 was 41.82; hence the record for 1935 was 9 percent better than that for 1934. Reports from operating companies showed that 51 men were killed by accidents in 1935 and 4,152 men were injured. (See table 37.) The industry employed 73,005 men and performed 110,033,341 man-hours of labor, an average of 1,507 hours of work per man. Measured in man-days, the total volume of labor was 14,623,303, or an average of 200 days of 7.52 hours per day for each man employed. These figures are not strictly comparable with similar figures for the preceding year, as the, coverage of the industry was more complete for 1935 than for 1934 because special facilities were available to the Bureau of Mines for conducting the 1935 canvass that were not available for the 1934 canvass. Reports covering identical plants that were active both in 1934 and 1935 indicate a reduction of about 7 percent in the number of men employed in 1935. This fact suggests that the apparent increase in the number of workers in 1935 is attributable chiefly, if not entirely, to the more complete coverage of operating plants in 1935. The plants from which this inference is drawn employed 21,799 men in 1934 compared with 20,248 in 1935.

Jan 1, 1937

By Albert L. Toenges, Louis A. Turnbull, Alonzo W. Quinn, J. M. Schopf, Arthur Neale, R. F. Abernethy

"INTRODUCTION The fuel requirements for industrial and domestic consumers in New England, in normal times, are supplied almost entirely by fuel oil, anthracite, and bituminous coal. A shortage of these fuels occurred during the war. This shortage was caused by (1) The diversion of oil to military uses; (2) the use of railroad and boat facilities that ordinarily would transport coal for the transportation of war materiel; (3) the inability of coal mines to apply the increased demand for coal which resulted from the conversion from oil to coal by domestic and industrial consumers; and (4) the increased demand of war industries for coal. Because of this critical fuel situation, an investiga¬tion was made of possible sources of fuel nearer to points of consumption in New England. Meta-anthracite, which is a satisfactory fuel for some purposes, had been mined in Massachusetts and Rhode Island many years ago. However, the introduction of freer-burning anthracite and bituminous coal into New England markets resulted in the abandonment of these mines.The coal mined in the vicinity of Portsmouth on Aquidneck Island, Newport County, R. I., had been used successfully for smelting copper ore and for fuel. It is reported that this coal is less graphitic than the material mined at Cranston near Providence, R. I. The coal is meta-anthracite and does not burn freely. However, improved equipment for burning coal has been developed, and if minable reserves of meta-anthracite should be found, methods of burning it probably could be devised.The purpose of this investigation was to determine sources of additional fuel. Since meta-anthracite mined at Portsmouth had been used with some success, an investigation was undertaken to determine the characteristics and continuity of the beds in this area."

Apr 1, 1948

By Lathrop E. Roberts

The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of Which it tends to form a layer of highly viscous "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and Van Arsdele have shown that the inclusion of grills of matte in the slag is also at tires very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in any laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slag as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even if only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separations from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and when present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by such elements as vanadium and molybdenum.

Jan 1, 1931

By James C. Fowler

As report covers the installation and testing of a permanent seismic monitor system at the Loveridge Mine in West Virginia. The testing of the system showed several things: 1. Getting the seismic data hack to the central computer in a usable form is possible 2. It is possible to detect small explosions. 3. The use of this system as a auxiliary system to detect hammer blows from miners trapped in the area of one of the geophones is possible.

Jan 1, 1974

By James Westfield

This report covers the calendar year 1953 and has been prepared and submitted in accordance with the provisions of Sec. 106(a) and Sec. 212(c) of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U.S.C. Secs. 451-483). During this first full calendar year of operations under the Federal Coal Mine Safety Act, the coal-mining industry of the United States attained the best injury records in its history - improving the former best records (made in 1952) by 91 fatal and 10,020 nonfatal injuries. Whereas, the mandatory provisions of the act were intended and designed to prevent major mine disasters, apparently the effects have reached beyond the scope thereof in reducing mine accidents generally.

Jan 1, 1954

By Patricia R. Devine

This appendix documents the mathematical approach to deriving the components of change presented in this report. The formulation closely follows that contained in Chapter IV of the documentation for the BEA 1977 Input-Output Tables.' The basic elements for the calculations include the "use" matrix (U), the "make" matrix (M), and any of the ten columns of final demand (generically represented by the symbol y). The use matrix contains information about changes in the technological processes of production, while the make matrix describes the nature of secondary product production in each industry. We adhere to BEA conventions in maintaining careful distinctions between commodity output (c) and industry output (x). The industry-by-industry 1-0 tables supplied by NYU for use in this analysis are square matrices, with the number of commodities and the number of industries both equal to 85. The BLS table for 1982 (commodity by industry) was aggregated and adjusted to be consistent with the earlier tables. The three basic steps for estimating components of change proceed as follows for each column of final demand. 1) Calculate the actual change in output of each commodity for each of the four time periods: 1963-72, 1972-77, 1977-82, and 1963-82.

Jan 1, 1988

The overall objective of this study is to gather operational data from selected surface coal mining systems in the United States, and to assess the potential production and economic capacity of the systems. The study includes: four mines, each using a different mining technique and different equipment. One mine was selected from each of the major coal fields: Midwestern, eastern,, northwestern, and southwestern. The Midwestern Mine is located in the Central Plains and produced 1.45 million tons of raw coal during the study year The Midwestern Mine uses the area mining or box-cut technique. A large in-pit shovel and a bucket wheel excavator are used to remove the overburden. Coal is removed by a loading shovel and transported to the dumping point by large off--highway trucks.

Jan 1, 1975

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By Nancy Potts, M. G. Barker, W. C. Holliman

"SUMMARYThis report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, end 10 grade 115/145 aviation fuels.The inspection test data supplied by the participating manufacturers consist of octane and performance numbers, tetraethyllead content, dye color, and other characteristics usually listed in aviation gasoline specifications, such as AN-F-48a or ASTM Designation D910-47T. These data are tabulated and averaged by grades in tables 1 through 4 and, as reported, meet the AN-F-48a and similar specifications with a few exceptions. Two grade 80 gasolines show a lean-mixture octane rating slightly below 80.0, and 91/98 grade fuel shows a lean-mixture rating of 90.9 and a rich-mixture rating of 97.5, two 100/130 grade gasolines have a rich-mixture performance number slightly below 130.0, and one 115/145 grade gasoline shows a rich-mixture performance number of 144.5. However, octane and performance number averages are above the mini¬mum requirements for each grade. Tetraethyllead content in the 91/98 and 100/ 130 grades generally is above the maximum outlined in these specifications, whereas dye color for each of the four grades, with the exception of two gasolines in grades 80 and 100/130, is that designated for the particular grade. Distillation requirements, with a few exceptions at individual points, are met by gasolines of all grades. Reid-vapor-pressure, copper-dish-residue, heat-of-combustion or aniline-gravity-constant, freezing-point, and copper-strip-corrosion requirements are met by all gasolines so far as reported. No data for some of these tests wore submitted on a few of the gasolines. One gasoline, grade 115/145, shows a sulfur content greater than the specified maximum."

May 1, 1948

By Walter Frank

The purpose of the work covered by this contract is to develop a ground and pilot conductor connector which will significantly improve mine trailing cable splice performance. This work compliments the work completed under Contract 00357100 on the development of crimp connectors for the phase conductors of trailing cables. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. As with the phase development work, the ground and pilot connector work is essentially of an empirical nature. As a result time is devoted to explaining the derivations of the test procedures used. In order to familiarize the reader with connector terminology a section is devoted to a glossary of pertinent terms. The connector design effort includes connectors for splicing ground and pilot conductors. A distinction is made between connectors suitable for splicing round and flat ground configurations. The same also applies to the pilot conductors. During the course of this work, much time has been devoted to the question of suitability of round cable configurations for trailing cable applications. This is discussed in detail along with resulting conclusions and recommendations. A field test program was conducted in order to confirm ground and pilot connector laboratory data. This testing also determined the viability of the connector designs and recommended installation techniques in a mine environment.

Jan 1, 1979

By McElroy. G. E.

"INTRODUCTION The ventilation of development faces in mines for diluting gas or dust concentrations and, in hot mines for providing air-motion cooling effect, by fan pipe units discharging high-velocity streams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, a subject on which little definite information is available. A study of the air flow from grills into rooms 3/ has provided some basic data, but under conditions no different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.The purpose of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pipe lines in mines. This series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of pipe, and adjacent walls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made by short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects due to size and shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs and are so reported."

Aug 1, 1940