Search Documents

By M. H. Kline, T. J. Ballard

"INTRODUCTION The Cranberry magnetite deposits occur in pre-Cambrian granite-gneiss in a belt extending from 3 miles southeast of Cranberry, N. C., to about 6 miles southwest of Magnetic City, Tenn. The belt forms a curve, elongated to the north, approximately 26 miles in length.The Bureau of Mines investigation has been confined to the eastern part of the belt, comprising the area from Fork Mountain, Avery County, N. C., to the Hcupscup Knob prospects in Carter County, Tenn.The deposits were worked at least as early as 1820. The Cranberry Iron & Coal Co. and its successors operated the Cranberry mine intermittently for about 50 years until 1930, when operations were abandoned.The magnetite rock is amenable to concentration. Numerous laboratory tests and pilot-mill operations have proved that a high-iron, and low-phosphorus concentrate can be obtained by fine grinding and magnetic, separation, the quality of the concentrate depending upon the extent of grinding. The principal objectives of the Cranberry project were threefold.The primary consideration for beginning exploration of the deposits was the need for developing additional deposits of high-grade iron ore during the war and for replenishing the war's depletion of iron-ore reserves for the peacetime economy. The emergency did not permit logical sequence bf development, and it was necessary to begin drilling before the geophysical survey was completed. The first drilling was begun at the Cranberry mine; and the holes were located from the geological data, coordinated with the position of the mine workings."

May 1, 1948

By Arne Landsberg

The Bureau of Mines measured the vapor pressure of FeC12 , FeBr2, FeI2, Sb, Bi, Cd, Mg, Pb, FeC13 , and VCl2 using the Knudsen-and torsion-effusion methods, and on FeC13 -NaC1 mixtures, Au2Cl6, and MgNi2 using only the Knudsen method. Apparent vapor pressures calculated from the experimental data vary with orifice size and method of determination. Reaction with residual oxygen in the instruments was noted to have an effect on the iron halide data. Vapor pressure curves plotted as log P versus 1/T (where P is pressure and T is absolute temperature) for one substance using several orifice sizes tended to converge at a single point when extrapolated beyond the experimental region. All of the data, except those of VC12, agree with previously published results. The importance of comparing effusion measurements with those obtained by other methods and the variations encountered with various orifice sizes are discussed.

Jan 1, 1977

By Forrest T. Moyer

Quarry accidents in 1963 caused 61 fatal and 3,468 nonfatal injuries which occurred at respective frequency rates of 0.31 and 17.91 per million man-hours of worktime. The fatality record in 1963 was better than in 1962 but was appreciably worse than in 1.961. For nonfatal injuries, the 1963 record was slightly worse than in 1962 but was better than in 1961. The injury--severity rate of 2,913 days lost or charged per million man-hours in 1963 was better than that of 3,046 in 1962, the first year for which such data became available. The average severity of all injuries in 1963 was 160 days lost or charged per injury, 15 less than in 1962. An average of 91,960 men were at work on active days in 1963 and these men had an aggregate worktime of 193.7 million man-hours during the year.

Jan 1, 1972

By T. A. Lang

Concepts and equations have been developed to quantitatively determine the stability of a rock bolted coal mine roof as a structural (beam-arch) member consisting of reinforced rock units. The equations take into account: rock bolt tension, length, spacing, and orientation; size of opening, strength and physical properties of the rock; and loads from distressed rock, and were critically reviewed using sensitivity analyses and the results available from relevant previous analytical and physical model investigations. It is concluded that they can essentially be validated by using small scale physical models and the full size mine entry model at the USBM Spokane Research Center. However, a comprehensive research program, including analytical and laboratory investigations and field trials in typical mines, will be required to define and validate criteria and standards for using the equations as a basis for a rational design code for rock reinforcement installations to replace the semi-empirical rules now being used. For example, these studies have shown that the practice of installing vertical roof bolts with a uniform spacing equal to the bolt length is inherently unsafe and that the spacing should be reduced near the walls to prevent shear failure of the roof strata. The development of such a rational design code would provide enhanced safety in coal mining operations and warrants a high priority in the Bureau's ground control research program.

Jan 1, 1981

By Thomas P. Mucho, Thomas M. Barczak, Dennis R. Dolinar

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial-and-error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground reaction behavior based on support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health's (NIOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate application of alternative roof support systems or to design in-mine trials so that a fair and equitable comparison of different support systems can be made. A case study of the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to the conventional wood and concrete cribbing historically used at this particular mine.

Jan 10, 2000

By Robert Vinson

This article examines the spatial variability of dust concentrations within a coal miner?s breathing zone and the impact of sampling location at the cap lamp, nose, and lapel. Tests were conducted in the National Institute for Safety and Health Pittsburgh Research Laboratory full-scale, continuous miner gallery using three prototype personal dust monitors (PDM). The dust masses detected by the PDMs were used to calculate the percentage difference of dust mass between the cap lamp and the nose and between the lapel and the nose. The calculated percentage differences of the masses ranged from plus 12% to minus 25%. Breathing zone tests were also conducted in four underground coal mines using the torso of a mannequin to simulate a miner. Coal mine dust was sampled with multi-cyclone sampling cans mounted directly in front of the mannequin near the cap lamp, nose, and lapel. These four coal mine tests found that the spatial variability of dust levels and imprecision of the current personal sampler is a greater influence than the sampler location within the breathing zone. However, a one-sample t-test of this data did find that the overall mean value of the cap lamp/nose ratio was not significantly different than 1 (p-value = 0.21). However, when applied to the overall mean value of the lapel/nose ratio there was a significant difference from 1 (p-value < .0001). This finding is important because the lapel has always been the sampling location for coal mine dust samples. But these results suggest that the cap location is slightly more indicative of what is breathed through the nose area.

Jan 1, 2007

By D. Harrington

A uniform hoisting-signal code for mines hoisting from more than one level, if adopted by all mining States, would be beneficial to employees and owners alike and should largely reduce the number of hoisting accidents. Misunderstood hoisting signals cause many shaft accidents involving injuries to men, damage to equipment, and loss of production from the resultant delay. Many of the metal-mining States have adopted codes for hoisting that are effective within the borders of that State but usually entirely different from the signal code, if any, in use in an adjoining State. For many years safety engineers have recognized this lack of uniformity as a distinct hazard, but a uniform code has never been adopted by the States or by the mining industry in those States that have not incorporated signal codes in their mining laws or mining regulations.

Jan 1, 1944

By W. R. Hardwick

This paper describes open-pit mining methods and practices at Copper Cities Division of Miami Copper Co, in Gila County, Ariz. It is one of a series being prepared by the Burea of Mines on mining methods, practices, and costs in various mining districts of the United States. A similar program, conducted from 1928 to 1939, provided technological information on the development and conservation of our mineral resources and assisted operators and engineers in evaluating and developing new mineral deposits. This circular contains a brief history of the district and describes the Copper Cities deposit, with particular emphasis on a detailed description of those characteristics--physical, economic, or engineering--that affect the choice of mining method. Prospecting and exploration, sampling and estimation of tonnage and values, development, and mining (including breaking ground, loading, hauling, ore control, and auxiliary operations related to mining) are described, Percentage of extraction, production rate, safety, first aid, Eire prevention, mine organization, and processing plant are discussed briefly, The final section gives such costs, on a percentage basis, as are available for publication. Where relevant, some information on the Castle Dome mine is included.

Jan 1, 1960

By Peter Swanson

One of the primary methods for analyzing roof stability in underground mines is the age-old method of “roof sounding” where a miner taps on the roof and listens for the hollow sound of loose blocks of rock. This paper looks at the feasibility of using noncontact laser-based vibration measurements to detect roof fall hazards with the ultimate vision of improving, expanding and automating procedures for mine roof inspection. Vibration measurements made on loose blocks of rock in underground mines are summarized and compared to estimates of fundamental resonance frequencies for rock slabs of the size responsible for highly hazardous “skin failures.” Both laser Doppler vibrometry and full-field interferometric methods are examined and are considered to be feasible methods for detecting anomalous vibrations in loose roof rocks. Results from simple laboratory experiments using laser vibrometry demonstrate some of the proposed application concepts. While considered a challenge to move these techniques from the laboratory to heavy industrial or outdoor environments, the potential for success in the current application is enhanced by the reduced requirements of qualitative analyses.

By Alexander L. Peyton

The Magruder and Chambers copper deposits in the Little River gold district, on the border line of Lincoln and Wilkes Counties, Georgia, have been known for a number of years (fig. 1). The Magruder deposit was first opened as a gold mine but has produced mostly copper and load. Records show that about 50 cars of concentrates were shipped from this property. No record of any production at the Chambers deposit is available. The Bureau of Mines, in its program of investigation of strategic minerals deposits, diamond drilled 10 holes, totaling 3,784 feet, on the two properties between December 3, 1948, and June 23, 1949. Eighty-eight core samples were analyzed, and the analyses and drill-hole data are presented in this report.

Jan 1, 1950

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By Forrest T. Moyer

INJURY experience and related employment information are presented in the chapter for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1964. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. All rates in the text are calculated separately on data before rounding, hence component rates may not add to the total rates shown in the tables. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III. COAL Injury experience of the coal mining industry was improved in 1964, as measured by the declines of 1 and 14 percent, respectively, in the frequency and severity rates. Although the total number of injuries increased in 1964, a slightly greater proportional increase in man-hours worked caused the frequency rate to drop to 44.65 per million man-hours. The injury-severity rate in 1964 was 7,832 days lost per million man-hours of exposure. Employment and injury data for 1964 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines. Fatality experience improved significantly with a record low number of 240 deaths in 1964. This total was 44 less than in 1963. The Nation&apos;s coal mines during 1964 were free of major disasters (a single accident resulting in the death of five men or more) for the first time since 1956. The

Jan 1, 1965

By Whitman E. Brown

"As part of a Nation-wide program of the United States Government to develop natural resources, funds were made available to the Bureau of Mines for the investigation of the ""Reduction of Iron Ores by Solid and Gaseous Fuels."" These investigations are concerned with the direct production of iron from its ores without the use of a blast furnace. Many processes have been proposed for the low-temperature reduction of iron oxides, but few have been developed to commercial use. High-quality sponge iron is produced com-mercially only in Sweden.The cost of iron production depends in part on the grade of the ore and increases with decrease in grade. The substitution of cheap natural gas in a sponge-iron process for expensive coke in smelting in the blast fry pace would partly compensate for the use of low-grade ores. If a process can be developed in which inexpensive natural gas can be used as fuel and reducing agent, the large deposits of low-grade iron ore and the natural-gas resources of east Texas may be utilized in the commercial production of sponge iron.Sponge iron may possibly be used to supplement scrap iron, pig iron, or, in special instances, wrought iron. Sponge iron will vary but slightly in composition and will contain little or no nickel, cobalt, manganese, copper, and other allowying metals. It is becoming increasingly difficult to obtain choice scrap iron of nonalloy composition. Pig iron contains 1.5 to 3.0 percent silicon and 3.0 to 4.5 percent carbon. Sponge iron generally contains less carbon than pig iron.The Madaras Steel Corp. in Longview, Tex., built a set commercial-scale sponge-iron plant which was intended to be operated in connection with a steel foundry. The process is based upon the reduction of preheated iron ore, with hot reducing gases under pulsating pressure. Although the Madaras Corp. had previously experimented with the production of sponge iron by reducing the ore with pure hydrogen, several attempts to use a re-formed natural gas as the reducing agent in this pilot plant were unsuccessful. The Bureau of Mines leased this plant and conducted an extensive investigation of the Madaras process on a semicommercial scale.The experiments were not entirely satisfactory, partly because of mechanical difficulties and partly because the reducing gas was not of the best quality. However, much information on the production of reducing gas by re-forming natural gas and on the reduction of iron ore with re-formed natural gas was obtained.The sponge iron produced contained approximately 0.1 percent phosphorus; and, after melting in an electric furnace, the iron contained approximately 0.15 percent phosphorus. The results of attempts to improve the ore by ore-dressing methods were not encouraging."

Aug 1, 1946

By John L. Edwards, Anthony T. Iannacchione

There has been a persistent need to forecast roof falls so that miner’s exposure to hazardous underground environments can be minimized. Several monitoring techniques have been developed and are used today with varying levels of acceptance in the mining industry. This paper examines the potential for monitoring microseismic emissions activity as a means of forecasting roof falls. The use of this activity to forecast roof falls has drawn only limited attention, resulting in a lack of published field performance data. This deficiency is being partially addressed by analyzing data obtained during longwall mining at Moonee Colliery in 1998. The Moonee data base contains a wealth of information concerning roof fall forecast parameters and the seismic alarm criteria used to develop these forecasts. Four seismic alarm criteria were developed and used by Moonee with varying degrees of success. Roof falls were forecasted 73% of the time with average forecast times of 54 minutes. Ninety percent of the predicted roof falls had a warning time, i.e., the time between warning and roof fall event, of greater than 1 minute. The fraction of forecasted roof falls decayed logarithmically as a function of warning time, until only 20% of events were predicted more than 100 minutes prior to roof falls. False alarms occurred in 50% of the warnings. Many of the false alarms were quickly followed by a cessation in mining which could have temporarily halted the on-going failure process. If mining had continued immediately after the false alarms, a roof fall may have occurred soon after. The microseismic activity collected from Moonee Colliery demonstrates that techniques to forecast roof rock instabilities in underground mines are possible.

By Gustav Wirth

"ABSTRACTIn exothermic and endothermic catalytic reactions, control of the temperature is of utmost importance. Basic calculations are developed for determining catalyst volumes of various types of reactors that give particular temperature distributions, and the individual designs are compared.INTRODUCTIONA narrow range of permissible operating temperatures characterizes many, catalytic reactions, and yields of the desired product are reduced sharply if operating temperatures fall outside of this optimum range. In order to achieve close temperature control, reactors with internal heat exchange have been developed in which thin layers of catalyst are located between cooling surfaces.The temperature distribution for an exothermic reaction in such a thin catalyst layer is shown in figure 1. Reactive gases flow downward through the catalyst section, which is 2so wide. It is assumed that a constant amount of heat is generated per unit of bulk catalyst volume, and that this heat is entirely removed through the walls. Consequently, except for a short section at the entrance of the reactor, the heat of reaction is not available for raising the temperature of the gases. Thus, at all points equidistant from the axis, the temperature is the same throughout the entire reactor. At the middle of the gas stream, the temperature is designated as uo. Traveling radially from this point, the temperature decreases because of the removal of heat through the walls and reaches, in the vicinity of the cooling surface, the value u1. Over a relatively narrow zone of width, b, the temperature falls to the value u2 at the cooling surface. Because inadequate data are available on heat-transfer coefficients for a gas flowing through a porous bed, and also because the narrow zone, b, is probably without effect on the reaction by virtue of its low temperature, the temperature drop in this zone at the cooling wall was disregarded. The following calculations were made on the basis of the temperature drop (u0 - u1) resulting from heat conduction within the main body of the catalyst bed only."

Nov 1, 1950

By William O. Vanderburg

This report 3/gives the results of a reconnaissance of the mining districts in Lander County, Nev., made from March 29 to April 20 and from May 9 to May 21, 1938, during which virtually all of the mining districts n the county were visited. No attempt has been made to include in this report all the mines and prospects in the various mining districts, and it should be stated that whether or not a property is mentioned herein has no. bearing on its merits. The report rovers the situation of the various districts, types of ore deposits, ownership and description of mines and prospects, information on past and current activity, and other information of economic interest likely to be useful to those interested in the development of our mineral resources. The names of the various districts mentioned are those generally used when they were organized for purposes of record and regulation. When originally organized, the districts embraced large areas with no well-defined boundaries, so that the names have little geographical significance.

Jan 1, 1939

By A. Matzick

In its work under the Synthetic Liquid Fuels Program the Bureau of Mines has developed on a 6-ton-a-day-pilot-plant scale a continuous, gravity-feed retort far distilling oil from oil shale. The development work covered by this report was done from January 27, 1950, to January 26, 1952, at the ail-Shale Experiment Station near Rifle, Colo. Over 300 pilot-plant tests were made during the investigation. The basic retort developed has been named the Gas-Combustion retort. In this process, part of the heat for retorting of the shale is generated by burning recycled product gas in a combustion zone within the descending shale bad in the retort. Additional heat is supplied by combustion of the carbonaceous residue remaining in the spent shale after the oil has been distilled. Air for combustion is admitted through an air distributor in the center of the bed at about the mid-point of the retort. Hot gas rising from the combustion zone heats countercurrently the descending raw shale and liberated shale oil by pyrolysis of the shale. After passing through and exchanging heat with the incoming raw shale, the oil is condensed as a fog or mist in the gas, which is withdrawn at the tip of the retort. The cool gas is then piped to an oil-recovery system where the oil is separated from the gas in centrifugal separators or other types of mechanical or electrostatic separators. The hot, spent shale below the combustion zone is cooled by heat exchange with recycle gas, which is a portion of the effluent gas from the oil-recovery system.

Jan 1, 1955

By William D. Monaghan, Michael A. Trevits

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH’s Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

By J. R. Thoenen, J. L. Vallely, M. C. Malamphy

"SUMMARYMagnetic and gravimetric surveys wore conducted over an area of ap¬proximately 1,400 square miles in the bauxite district of central Arkansas. The primary purpose of these surveys was to discover any possible buried and hitherto unknown syenite masses favorable for the occurrence of bauxite and to determine the approximate position of the buried flanks of the known syenite masses which might offer conditions favorable for the discovery of new ore bodies.Those surveys indicated that the various syenite outcrops were domes or bosses on a large batholith and that ether similar domes occurred on the batholith but did net outcrop.Drilling on the local geophysical anomalies proved the presence of 10 buried domes, but only 2 of them were found to project above the upper surface of the Midway clays, a requisite of conditions favorable for the occurrence of bauxite ore bodies. The geophysical data indicated the approximate configuration of the buried flanks of the known syenite coutcrops, and the portions of these flanks that project above the Midway have now been outlined more accurately by drilling.The geophysical surveys have produced evidence permitting the elimi¬nation of a large area as unfavorable for the occurrence of bauxite.Magnetic surveys extending along the Midway-Wilcox contact from Gurdon, in Clark County, on the southwest to Searcy, in White County, on the northwest have proved the improbability of the existence of other syenite masses similar to those found in Pulaski and Saline Counties. A detailed magnetic survey of the Magnet Cove area in Hot Spring County has proved that the syenite mass exposed in that locality is an isolated intrusion and entirely unrelated to those of Pulaski and Saline Counties. This syenite mass does not occur under conditions believed to be favorable for the occurrence of bauxite."

Feb 1, 1945

"D bed, Ky., coaL, washing characteristics RII 5140coking coal, reserves, estimate RI 5037Pa., coal, washing characteristics RI 4834, 4941D bed mine, Ky., coal, washig characteristics"

Jan 1, 1960