Search Documents

By S. Sinha, S. Ganguly

"In an opencast mine explosives are used for fragmentation of rock. Inefficient use of explosive energy in an opencast operation produces excessive ground vibration, which is measured by peak particle velocity (PPV). To mitigate ground vibration, it is essential to develop a model to predict PPV. At present empirical models are used. These models are based on only a few input variables, hence they fail to take into account the effects of the myriad factors that cause ground vibration. Due to lack of explicit knowledge about the complex mine blasting system the scope of application of mathematical and statistical modeling techniques is limited. The artificial neural network (ANN) technique is a learning algorithm that can remove some of these limitations and can be applied to predict PPV. In this paper an ANN model is developed for prediction of blast vibration using 248 data records collected from three coal mines with diverse geomining conditions. The correlation coefficient between measured PPV and model output was found to be 0.96 and the average error percentage 11.85. The ANN model output was compared with the output of three empirical models that are widely used for prediction of PPV. The correlation coefficient between the PPV predicted by an empirical model and measured PPV data was 0.63 and the relative error percentage 38.47. This result demonstrates the superiority of the ANN model compared to empirical blast models. By using site-specific structural discontinuities as input the model performance can be further improved. Sensitivity analysis and 3D plotting were used to gain further knowledge about blast-induced ground vibration. IntroductionIn an opencast coal mine explosives are used for fragmentation of coal and overburden. If the explosive energy is not fully utilized it causes blast-induced ground vibration, which may damage nearby structures. Ground vibration is expressed as peak particle velocity (PPV). During different stages of mine planning and operation, it is necessary to use a ground vibration prediction model for blasthole design. Selection of the modelling technique is crucial. Mathematical and statistical modelling techniques have limited application because of the lack of explicit knowledge about the complex mine blasting system. Vogiatzi (2002) highlighted the problem of multicollinearity in case of statistical modeling techniques. Mutalib et al. (2013) stated that mathematical models are unable to capture the nonlinear relationship between several blasting-related parameters due to the complexity of the model input data. However, the difficulty involved in modelling complex blast vibration problems can be removed by adopting an alternative soft computing modelling approach. One of the soft computing techniques is the artificial neural network (ANN). Ragam and Nimaje (2018) developed an ANN model for predicting PPV using six input variables. Kosti et al. (2013) stated that the conventional predictors fail to provide acceptable prediction accuracy. They showed that a neural network model with four mine blast parameters as input could make significantly more accurate on-site predictions. Sayadi et al., (2013), using a database from Teheran Cement Company limestone mines, found that a neural network resulted in maximum accuracy and minimum error. Khandelwal and Singh (2009) developed an ANN model using 150 data records from an Indian coal mine with site-specific rock characteristics and geomining setting. Khandewal and Singh (2007) built a ground vibration prediction model for a magnesite mine using four prediction variables with 20 data records. Kamali and Ataei (2010) predicted PPV in the structure of the Karoun III power plant and dam using an ANN. El Hafiz et al. (2010) evaluated ground vibration predictors using data from a single-station seismograph at a limestone quarry in Egypt."

Feb 1, 2019

By A. V. Z. Brink

Rock engineering risk is defined in this paper as a function of the potential ground motion; the vulnerability of the workplace; exposure of people; and a general term – quality of information. The paper describes the development of prototype software that is a combination between an expert system approach for determining overall risk assessment, a risk control recommendation and a basic GIS (Graphic Information System) approach for graphically overlying input parameters and the output risk. The expert system uses a Bayesian probabilistic approach to combine various workplace-related information, a quantified seismological environment and the exposure of underground staff to provide an overall RE risk rating. The risk assessment is dynamic in that it is recalculated each time that any of the input parameters change, for example each time a seismic event is recorded in the area of interest. The code was tested on a data set from Savuka Gold. As risk assessment is not an absolute prediction of a specific outcome, it is therefore not possible to relate to individual case studies and the reliability of this method would only be determined after an extensive period of use with appropiate back-analysis. Le risque dans le génie minier est défini dans cette étude comme une fonction du mouvement potentiel de terrain ; la vulnérabilité du lieu de travail ; l’exposition des personnes ; et un terme général – la qualité de l’information. L’étude présente décrit le développement d’un logiciel prototype qui est une combinaison entre une démarche de système expert pour déterminer une évaluation générale du risque, une recommandation pour le contrôle du risque, et une démarche de SIG (Système d’Information Géographique) pour superposer graphiquement les paramètres d’entrée et le risque de sortie. Le système expert utilise une méthode de probabilité bayésienne pour combiner des informations variées sur le lieu de travail, des données quantifiées sur l’environnement sismique, et l’exposition du personnel travaillant sous terre, pour finalement produire un classement général de risque minier (RE). L’évaluation du risque est dynamique en ce sens qu’elle est recalculée à chaque fois qu’un des paramètres d’entrée change, par exemple à chaque fois qu’un évènement sismique est enregistré dans la région. Le code fut testé sur un ensemble de données obtenues de Savuka Gold. Comme l’évaluation du risque ne constitue pas une prédiction absolue d’un résultat spécifique, elle est par conséquent difficile à rattacher à des cas individuels et la validité de cette méthode ne pourrait être déterminée qu’après une longue période d’utilisation avec analyse rétrospective appropriée. Das Gesteinstechnikrisiko wird in dieser Arbeit als Funktion einer möglichen Bodenbewegung definiert; die Anfaälligkeit des Arbeitsplatzes; das Ausgesetztsein der Belegschaft; und ein genreller Begriff - Qualität der Informationen. Das Papier beschreibt die Entwicklung einer Prototyp-Software, die eine Kombination zwischen einem Expertensystemzugang für die Bestimmung der gesamten Risikobeurteilung ist, eine Empfehlung zur Risikokontrolle und eines fundamentalen GIS (graphisches Informationssystem) Zuganges für graphisch darüberliegende Eingangsparameter und das Outputrisiko. Das Expertensystem verwendet eine bayesische Wahrscheinlichkeitsannäherung, um verschiedene mit dem Arbeitsplatz in Verbindung stehende Informationen, ein quantitativ bestimmtes seismologisches Umfeld und das Ausgesetztsein des Untertag-Personals zu kombinieren, um eine gesamte RE-Risikobewertung zur Verfügung zu stellen. Die Risikobeurteilung ist insoferne dynamisch,daß sie stets nachkalkuliert wird wenn sich irgendeiner der Eingangsparameter ändert, z.B. jedesmal wenn ein seismischer Fall im Interessensbereich aufgezeichnet wird. Der Code wurde auf einem Datenbestand von Savuka Gold geprüft. Da die Risikobeurteilung nicht eine absolute Vorhersage eines spezifischen Resultates ist, es ist folglich nicht möglich, sich auf einzelne Fallstudien zu beziehen und die Zuverlässigkeit dieser Methode könnte nur nach einer umfangreichen Benutzungsdauer mit geeigneter Postanalyse bestimmt werden.

Jan 1, 2003

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

What is a nugget effect? In the early development of geostatistics, the term ?nugget effect? was coined for the apparent discontinuity at the beginning of many semivariogram graphs. This name was chosen to reflect the large differences found between neighbouring samples in ?nuggety? mineralizations such as Wits gold reefs. Geostatistical theory assumes that the difference between a sampled value and a potential repeat sample at the same location is actually zero. Included in this ?nugget effect? would be true variation between contiguous samples due to the nature of the mineralization, micro-fracturing, nugget or crystal size, and so on. Also included in the nugget effect would be any ?random? sampling variation which might occur due to the method in which the sample was taken, the adequacy of the sample size, the assaying process, etc. Arguments were put forward that ?sampling errors? actually exist at zero distance. Some geostatistical schools actually maintain that the ?nugget effect? is all sampling error. This would imply that ?perfect? sampling would eliminate the nugget effect entirely. There is now a dichotomy both in the geostatistical world and in the software packages provided for geostatistical analyses. It may seem academic to argue over whether the semivariogram model should take a value of zero, a value equal to the nugget effect, or a partial value at distance zero. However, the decision can have a profound effect on both the estimated resource and in our confidence on that resource. Whereas most geostatistical texts define the semivariogram model as taking the value of zero at zero distance, others imply that the full nugget effect should be used at zero distance. For example: ?The nugget effect refers to the nonzero intercept of the variogram and is an overall estimate of error caused by measurement inaccuracy and environmental variability occurring at fine enough scales to be unresolved by the sampling interval3 ?Christensen4 has shown that the ?nugget effect?, or non-zero variance at the origin of the sernivariogram, can be reproduced by a measurement error model ?The nugget effect is considered random noise and may represent short-scale variability, measurement error, sample rate, etc.5. In many training texts and Web courses, the definition of the semivariogram is ambiguous as the formulae for semivariogram models is not actually specified at zero distance6,7,8.

Jan 1, 2010

By W. Lin, H. Endo, M. Kwasniewski, A. Kamei, M. Takahashi

Uniaxial tension tests were conducted on specimens of eleven granitic rocks which came from eastern Japan, and included a granite, four granodiorites, four tonalites and two gabbros. The axial and transversal deformability of these rocks was determined based on strain measurements using wire strain gauges. The experimental test results revealed that deformational properties of the rocks investigated varied depending on their petrographic features. However, the axial strain and the lateral strain characteristics showed a similar trend for all the rocks, i.e. the stress-strain curves were non-linear throughout the whole stress range from the initial point of loading to the point of ultimate failure. Moreover, the tangent Young's modulus and the ratio of the lateral strain to the axial strain decreased monotonously with the increasing of the axial stress. Still, the deformational properties were different for individual rocks in a quantitative sense. In particular, the difference in the lateral strains among different rocks was more distinct than that in the axial strains. For example, the Poisson's ratio at a stress level equal to 50% of the ultimate strength of a granodiorite was very low, close to zero. Furthermore, the Poisson's ratio of a tonalite was lower than that of a granodiorite, and assumed a negative value. This effect occurred because the lateral strain became positive as it changed from contraction at the initial stage of loading to extension at higher stress levels. There is no ready explanation for this phenomenon; it is believed, however, that it occurs due to microcracks pre-existing in rock materials and/or weak bonds between the adjacent mineral grains. Les essais de traction directe ont été conduits sur les échantillons de onze roches granitiques provenant de la région Est du Japon: un granit, quatre granodiorites, quatre tonalites et deux gabbros. Déformabilité axiale et transversale de ces roches s’était déterminée en utilisant des jauges extensométriques à fil. Les résultats obtenus à partir des essais montrent que la déformabilité des roches examinées varie selon leurs propriétés pétrographiques. Cependant, à partir des essais, une tendance semblable était observée dans les paramètres de la déformation axiale et la déformation latérale de toutes les roches; c'est-à-dire chaque courbe de contrainte-déformation était non-linéaire dans tout l'intervalle de contraintes à partir de l’état initial jusqu’à l’état d’une rupture finale au cours du chargement. De plus, le module tangent de Young et le rapport de la déformation latérale sur la déformation axiale a diminué de manière monotone avec l'augmentation de la contrainte axiale. Cependant, les différences quantitatives de propriétés de déformation sous traction étaient observées entre des roches individuelles. Particulièrement, la différence de déformations latérales était plus notable que celle-là de déformations axiales entre des roches différentes. Par exemple, le coéfficient de Poisson à un niveau de contrainte égal à 50 % de la résistance d'un granodiorite était très bas, près du zéro. En outre, le coéfficient de Poisson de la tonalite était inférieur que celui du granodiorite et a assumé une valeur négative. Cet effet est apporté parce que la déformation latérale est devenue positive en passant de la contraction dans l'étape de chargement initiale à l'extension sous les contraines plus hautes. Il n'y a aucune explication prête de ce phénomène; on prétend, cependant, qu'il est induit par des microfissures préexistantes dans des matériaux rocheux et/ou des joints faibles entre les grains minéraux adjacents. Einaxiale Zugversuche wurden auf Probestuecke von elf frischen, in Ostjapan vorkommenden, granitartigen Gesteinen durchgefuehrt, welche einen Granit, vier Granodiorite, vier Tonalite und zwei Gabbros umfassten. Die axiale und transversale Verformbarkeit von diesen Gesteinen wurde durch Verformungsmessungen mit Drahtdehnungsmessstreifen geklaert. Die experimentellen Versuchsergebnisse offenbarten, dass Verformbarkeitseigenschaften des untersuchten Gesteins in Abhaengigkeit von ihren petrographischen Eigenschaften variierten. Jedoch zeigten die axialen und die lateralen Spannungsdehnungslinien eine aehnliche Tendenz bei allen Gesteinen, d.h. die Verformungskurven waren nicht linear im ganzen Bereich vom Ausgangspunkt des Belastens bis zum Punkt des entgueltigen Bruchs. Ausserdem verringerten sich das tangentiale Elastizitaetsmodul und das Verhaeltnis der lateralen Verformung zur axialen Verformung monoton mit der Erhoehung der axialen Spannung. Dennoch waren die Verformbarkeitseigenschaften der einzelnen Gesteine in der quantitativen Wahrnehmung unterschiedlich. Insbesondere war der Unterschied bezueglich der lateralen Verformungen zwischen verschiedenen Gesteinen eindeutiger, als der in den axialen Verformungen. Z.B. war die Querkontraktionszahl auf einem Spannungsniveau, das 50% der Zugfestigkeit eines Granodiorits entspricht, sehr niedrig und nah an Null. Ausserdem war die Querkontraktionszahl eines Tonalits negativ und deshalb niedriger als die eines Granodiorits. Dieser Effekt trat auf, weil die laterale Verformung, als sie sich von der Kontraktion am Ausgangsstadium des Belastens bis hin zur Ausdehnung auf den hoeheren Spannungsniveaus aenderte, positiv wurde. Es gibt keine fertige Erklaerung fuer dieses Phaenomen; es wird jedoch angenommen, dass es wegen der Mikrorisse auftritt, die vorher im Gesteinsmaterial und/oder in den schwachen Bindungen zwischen den angrenzenden Mineralkoernern existieren.

Jan 1, 2003

By D. F. Malan

This paper provides an overview of the concepts of citations and journal impact factors, and the implications of these metrics for the Journal of the Southern African Institute of Mining and Metallurgy (JSAIMM). Two key research literature databases publish journal impact factors; namely, Web of Science and Scopus. Different equations are used to calculate journal impact factors and care should be exercised when comparing different journals. The JSAIMM has a low impact factor compared with some of the more prestigious journals. It nevertheless compares well with journals serving other mining sectors, such as the Canadian CIM Journal. The problems associated with journal impact factors are discussed. These include questionable editorial practices, the negative impact of this concept on good research, and the problem of a few highly cited papers distorting the journal impact factor. As a consequence, there is growing resistance to the use of journal impact factors to measure research excellence. The San Francisco Declaration on Research Assessment is a global movement striving for an alternative assessment of research quality. As a recommendation, the Editorial Board of the JSAIMM should adopt a pragmatic approach and not alter good journal policies simply to increase the journal impact factor. The focus should remain on publishing excellent quality papers. Marketing of the Journal, the quality of the published papers, and its open access policy should be used to counter the perception that journals with high impact factors are better options in which to publish good research material.

Sep 1, 2022

By K. Shin

Determining the anisotropy of rocks has in the past been difficult and rarely attempted in engineering practice. Here we have developed a new practical methodology for measuring orthotropic anisotropy that requires only one hollow cylinder specimen to determine the anisotropy of a set, even when the directions of the anisotropic axes are unknown. Autrefois, la détermination de l’anisotropie des roches était difficile et elle a été rarement essayée dans la pratique de l’ingénierie. Voilà c’est nous qui avons mis au point une nouvelle méthodologie pratique pour mesurer le coefficient de conductibilité thermique de l’anisotropie qui exige un seul spécimen du cylindre creux afin de déterminer l’anisotropie d’une série, même si les directions des axes anisotropiques sont inconnues. Früher war die Bestimmung der Anisotropie von Gesteinen ein schwieriges Verfahren, das in der technologischen Praxis nur selten in Angriff genommen wurde. Wir haben hier eine neue praktische Methodik zur Messung der orthotropen Anisotropie entwickelt, bei der nur ein Hohlzylinder an Gesteinsproben benötigt wird, um die Anisotropie einer Reihe von Steinen zu bestimmen, selbst wenn die Richtungen der Anisotropieachsen unbekannt sind.

Jan 1, 2003

By R. Drummond

The fourth Teetered Bed Separator (TBS) has just been installed in Australia, and trials have been run in many sites. There is a growing recognition of the potential advantages of using TBS technology to treat coal in the ?3+0.25 mm size range, at cut points below 1.60. From these activities, there has been a substantial growth in knowledge with respect to application engineering and operational functions. The paper briefly describes the installations, including flowsheets, and so provides a background to the potential deployment of TBS technology. There are a large number of potential applications for TBS technology, including treatment of fine ROM coal in new plants, or in upgrade situations for re-processing of spiral product, or scavenging coal from coarse tailings. As well, cost effective capacity upgrades are possible by using TBS units for treating the sands size fraction. Issues arising from Australian TBS installations and application engineering are also discussed.

Jan 1, 2002

By V. Jovicic, J. Likar

The knowledge of the geological sequence and hydrological conditions in the area of portals was the basis for the design of the entry of the highway into tunnel Trojane. Mudstone, claystone and sandstone dominate the rock layering, which is tectonically reworked and contains structural anomalies. The complexity of the sequence makes it impossible to survey all the relevant features along the full 3km length of the tunnel. Sudden and frequent transitions between litological sequences impose potential instabilities and make the excavation of the tunnel particularly difficult. The initial survey established the zones of potential failures. These were monitored using topographic survey and inclinometers with an aim to make further geotechnical analyses more reliable and adjusted to the ground conditions. The analyses of the wall construction and the results of the monitoring showed that the design of the retaining wall was adequate. La connaissance de la séquence géologique et des conditions hydrologiques dans l'aire des portails a été la base pour la planification de l'entrée de l'autoroute dans le tunnel Trojane. Le schiste, l'argilite et le grès dominent la couche rocheuse qui est tectoniquement transformée et contient les anomalies structurales. A cause de la complexité de la séquence, il est impossible de revoir toutes les particularités le long des 3 kilomètres de la toute longueur du tunnel. Les transitions soudaines et fréquentes entre les séquences lithologiques imposent l'instabilité potentielle et font l'excavation du tunnel particulièrement difficile. La revue initiale a été établie sur les zones où il existe l'éboulement potential. Elles étaient contrôlées à l'aide de la revue topographique et de l'inclinomètre pour que les analyses géotechniques suivantes soient plus sûres et adaptées aux conditions du sol. Les analyses de la construction des murs et des résultats du contrôle ont montré que la planification du mur réteneur était correspondante. Der Autobahneingang in den Trojane Tunnel war projektiert auf Basis von der Kenntnis der geologischen und hydrogeologischen Bedingungen in dem Portalgebiet. Das Gebiet besteht aus dem Tonstein und dem Sandstein. Die Schichten sind tektonisch verformt und sind deswegen sehr heterogen. Die anfaenglichen Untersuchungen haben die Zonen von den potentiellen Bruechen definiert. Weitere geotechnische Analysen waren fitted an reale geologische Bedingungen durch das Monitoring der potentiellen Bruchzonen, welches aus den topographyschen Messungen und Inklinometerdaten entstand. Die Analyse des Wandbaues und die Resultate von dem Monitoring haben erwiesen, dass die Wandprojektierung entsprechend war.

Jan 1, 2003

By B. Simser

At Brunswick Mine, an increase in the number of seismically-related falls of ground and in particular rockbursts occurred during 1999. This was due to the ever-increasing stress levels in the remaining ore reserves, mining in difficult highly stressed areas and in particular troublesome geological features. In conjunction with the Noranda Technology Centre, development of rockburst support systems started at the Brunswick Mine in 1996 and efforts were accelerated in 1999. A support package consisting of #6 gauge chain link mesh, #0 gauge heavy mesh straps, and a 1 m by 1 m pattern of modified conebolts was developed. The conebolts were modified to enable mixing of the resin anchoring. Two major rockbursts occurred during an intense seismic episode at the Brunswick Mine from October 13th to 17th , 2000.The area was evacuated approximately four hours before the first burst hit, and remained closed during the seismic ?flurry??. The first damaging activity occurred around midnight on Friday the 13th, and a second damaging episode occurred on the 17th that included a local Richter Magnitude 2.7 event. The second rockburst had dimensions of approximately 5 m by 5 m by 20 m or 2150 tonnes of massive sulphide material (density 4300 kg/m3). The first failure area was more extensive, caving approximately six metres of an intersection back with the lateral extent not safely measurable. This paper briefly describes the mining conditions that led to the bursting, the seismic response of the region, the mechanisms thought to have caused the bursts, and a yielding support system which had been partially installed before the burst.

Jan 1, 2002

By S. Mudau, P. Mohasoa, M. J. Cole

Derelict and ownerless (D&O) mines in South Africa have been an ongoing concern for over a decade. While some progress has been made to rehabilitate D&O asbestos sites, significant work remains, exacerbated by the growth in illegal mining. There are concerns regarding the accuracy and transparency of the D&O database, lack of oversight, and constrained funding, and the government is increasingly looking to the private sector to fund rehabilitation. Given these challenges, a new, sustainable approach to D&O sites in South Africa is needed to bring clarity and transparency to the process, recognise responsibilities and promote partnerships, and explore economic opportunities at D&O sites to reduce the financial liability and respond to the growing demand for critical minerals. This article has three components: i) reviews of international D&O good practices; ii) it analyses South Africa’s current approach and the D&O sites; and iii) proposes a D&O framework that addresses data, risk ratings, responsibilities and rehabilitation, economic opportunities, and stakeholder engagement. The study finds that the majority of the 6,100 so-called abandoned D&O mines are quarries and mine site features, 16% are operational, at least 11% have owners, and only 752 (12%) require rehabilitation. The framework aims to bring clarity and fairness to decision-making and to assign risk and responsibility for rehabilitation and seeks to incorporate economic opportunities to reduce the financial burden of rehabilitation, create jobs for local communities, and respond to the growing demand for critical minerals for the clean energy transition.

Apr 25, 2025

By A. Chiappone, M. Barla, U. Rabagliati, L. Repetto

ABSTRACT: The paper describes the application of both continuum and discontinuum modelling to the study of the stability conditions of the Alpetto mine, a high rock cut located in Cesana Brianza (Italy). The main objective is to provide valuable information for future mine planning and for the assessment of the stability conditions of the abandoned high rock cuts. Continuum modelling involved the applications of the finite difference method, whereas the distinct element method was used for discontinuum modelling. RESUME: L'article décrit l'application des méthodes de modélisation continue/discontinue pour l'étude des conditions de stabilité de la mine d' Alpetto, située à Cesana Brianza (Italie). Le but du travail consiste à determiner des paramètres utiles vis-à-vis du projet et d'estimer les conditions de stabilité de l'amas rocheux au terme de l'exploitation de la mine susmentionnée. La modélisation continue a impliqué l'application de la méthode des différences finis alors que la méthode des éléments distincts a été utilisée pour la modélisation discontinue. KURZFASSUNG: Der Artikel beschreibt die Verwendung der Modellierung von continuum und discontinuum zur Untersuchung/Studium der Stabilitätsbedingungen von der Alpetto Mine, hohe Aushubsfront in einer Felsmasse die sich in der Gemeinde von Cesana Brianza befindet. Das Hauptziel dieser Arbeit ist die Festlegung von Parametern die zur Planung nützlich/behilflich sein können sowie auch die Möglichkeit zur Analyse/Auswertung der Stabilität der Felsmasse-Front nach Aufhebung der Nutzung derselben. Die continuum Methode/Analyse wurde verwendet durch Unterstützung der Finite Differenz Methode da man für die Analyse der discontinuum (Fels als discontinuum beschrieben) der Distinct Elemente Methode verwendet hat.

Jan 1, 2003

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012

By Z. G. He, S. H. Chen, P. Egger

A new model for hollow rock bolts which comprises rock material, hollow bolt material, bolt/rock interface, is developed on the base of the composite element method (CEM). The main advantage of the new model is that it can be incorporated into the conventional finite element analysis. So the mesh generation of bolted rock structures becomes more convenient and feasible, which is very important in the optimisation of reinforcement design: the mesh can be kept unchanged when the number and orientation of bolts are adjusted. The comparison of the calculation results with a conventional FE approach shows the robustness of the proposed method. Un nouveau modèle numérique de boulons creux comprenant la roche, le matériau du boulon creux et l’interface roche / boulon est développé sur la base de la méthode des éléments composites (CEM). L’avantage principal du nouveau modèle est la possibilité de l’incorporer dans une analyse aux éléments finis conventionnelle. Ainsi la génération du maillage d’une structure rocheuse ancrée devient plus simple ce qui est très important pour une optimisation du projet : en cas d’ajustement du nombre et de l’orientation des boulons, le maillage reste inchangé. La comparaison de résultats de calcul avec ceux obtenus par un code aux éléments finis conventionnel montre la robustesse de la méthode proposée. Auf der Grundlage der Verbund-Element-Methode (CEM) wird ein neues Modell für hohle Reibungsanker entwickelt, das den Fels, das Ankermaterial und die Kontaktfläche Fels / Anker umfasst. Der Hauptvorteil des neuen Modells ist die Möglichkeit, es in eine konventionelle FE-Analyse einzubetten. So wird die Netz-Generierung für verankerte Fels-Bauwerke einfacher, was für die Optimierung des Verankerungs-Projekts von Wichtigkeit ist: wenn Zahl und Orientierung der Anker variiert werden, bleibt das Netz unverändert. Der Vergleich von Rechenergebnissen mit solchen aus einer konventionellen FE-Rechnung zeigen die Robustheit der vorgestellten Methode.

Jan 1, 2003

By T. Dlokweni

Several Rockmass classification systems have been developed and used in Civil Engineering design and for underground mining operations. Some of these rockmass classification systems have been modified and used in the South African coal mining industry to quantify descriptive geological information for use in coal mine design and roof support selection. The Coal Mine Roof Rating (CMRR) system developed in the USA has been investigated in detail as part of the study. Advantages and disadvantages of the system have been identified by means of underground and surface borehole testing. Investigations into the rating systems in South Africa found that most of the rating systems used in the South African coal mining industry are for planning purposes, and are conducted on borehole cores. This study also highlighted that the rating systems being used are based on geology, and that the human factor plays a major role in the rating systems. To overcome these problems, all the classification systems used in South African coal mines have been benchmarked against impact splitting technique and documented. The best elements of these systems are combined into a new standard system that will be easily used by all mine geologists and rock mechanics engineers. Plusieurs systèmes de classification de la masse rocheuse ont été développés et utilisés dans le Génie Civil et pour les opérations d'exploitation minière souterraine. Certains de ces systèmes de classification de la masse rocheuse ont été modifiés et utilisés dans l'industrie minière sud-africaine pour quantifier l'information géologique descriptive utilisée dans la conception de mines de charbon et la sélection de soutènement du toit. Le système d'Evaluation de Toit de Mine de Charbon (CMRR) développé aux USA a été examiné en détail, comme part de l'étude présente. Tests en surface de trous de mine ont permis d'identifier les avantages et inconvénients du système. Une étude des systèmes d'évaluation en Afrique du Sud a révélé que la plupart des systèmes d'évaluation utilisés dans l'industrie minière sud-africaine sont utilisés pour la planification, et sont menés sur les carottes de trous de mine. L'étude présente a aussi souligné que les systèmes d'évaluation utilisés sont basés sur la géologie, et que le facteur humain joue un rôle majeur dans les systèmes d'évaluation. Pour surmonter ces problèmes, tous les systèmes de classification utilisés en Afrique du Sud ont été référencés en termes de technique de fissuration sur choc, et documentés. Les meilleurs éléments de ces systèmes sont combinés dans un nouveau système standard qui sera utilisé aisément par tous les géologues de mine et les ingénieurs miniers. Verschiedene Gesteinsmassenklassifikationssysteme wurden entwickelt und kamen im Design für Hoch- und Tiefbau und Untertageabbau zum Einsatz. Einige dieser Gesteinsmassen-klassifikationssysteme wurden modifiziert und sind in der südafrikanischen Kohlebergbauindustrie in Verwendung, um beschreibende geologische Informationen für die Anwendung im Design von Kohlebergwerken und der Firstabstützungsauswahl quantitativ zu beschreiben. Das in den USA entwickelte Kohlengrubenfirstbewertungssystem (CMRR) wurde als Teil der Studie im Detail untersucht. Vorteile und Nachteile des Systems sind mittels der Untergrund- und Oberflächenbohrlochprüfung gekennzeichnet worden. Prüfungen der Bewertungssysteme in Südafrika ergaben, daß die meisten Bewertungssysteme die in der südafrikanischen Kohlebergbauindustrie benutzt werden, Planungszwecken dienen und werden anhand von Bohrlochkernen durchgeführt. Diese Studie hob auch hervor, daß die verwendeten Bewertungssysteme auf Geologie basieren und daß der menschliche Faktor eine Hauptrolle in den Bewertungssystemen spielt. Um diese Probleme zu überwinden, wurden alle in südafrikanischen Kohlengruben benutzte Klassifizierungssysteme vergleichsweise in Hinblick auf Spaltschlagtechnik überprüft und dokumentiert. Die besten Elemente dieser Systeme werden in ein neues Standardsystem kombiniert, das leicht von allen Grubengeologen und von Gebirgsmechanikingenieuren benutzt werden kann.

Jan 1, 2003

By H. Zhu, F. Xu, T. Wang

Abstract : The deformation monitoring data of the middle pier of the in permanent ship lock in Three Gorges revealed several interesting deformation phenomena. Conclusions and explanations are made concerning the phenomena in this paper, based on the finite element and engineering geology analyses. Firstly, the fluctuation of the horizontal transformations can be attributed to the alternate excavation of the two neighbouring ship lock rooms. Secondly, the rock mass discontinuities result in the displacement breaks. Lastly, the main reasons for the one-sided leaning phenomena are the natural stress, which is not evenly distributed, and the presence of discontinuities. This paper presents a valuable reference for studying the ‘individual phenomena’ in geotechnical engineering. ZUSAMMENFASSUNG: Die Beobachtungs claten an der Mittelpier deformation bezüglich Permannenter Schiffsschleuse in den Drei Schluchten offenbaren einige interessante Deformationsphänomene. Die Schlußforgerungen und Erklärungen dazu in dieser Arbeit basseren methodisch anf der ‚’ ‘Endlichen-Elemente-Analzse’ und der ‘Ingenieurnissen-Geograhnie-Analzse’. Erstens kann die Fluktuation der horiyontalen Transformation durch die ungleichzeitige Ausgrabung der zwei benachbarten Schiffsschleusenräume verursacht werden. Zweitens resultzert die Diskontinuität der Felsenmasse ans dem verlagerten Bruch. Drittens: Die Hauptgründe für das Zu-einer-Seite-Neigung-Phänomen in manchen Stellen sind der ungleich eigeteilte natürliche Druck und das vorhandersein der Diskontinuität. Diese Arbeit präsentiert eine wertvolle Referenz für die Untersuchung der Sonderfälle in geotechnischen Bau. Résumé: Cet article a analysé sérieusement et profondément , en utilisant des procèdes d’étude par exemple l’analyse d’éléments défini et celle de la condition géographique de traveaux , des règles typiques de la déformation montrées dans les données surveillantes à propos de la déformation des pierres centrales dans les écluses éternelles du Trois Gorges , on en a tiré une conclusion : 1) le changement des chiffres des déplacements horizontaux des pierres centrales est causé par les creusages séquentiels des cannelure voisines ; 2) l’inclinaison au Nord de toutes les pierres centrales entre les deuxième et troisième chambres d’écluse est causée par la différence de la gravitation entre les deux chambres d’écluse et par l’existence de la surface structurale ; 3) l’existence de la surface structurale cause le changement des chiffres des déplacements horizontaux des pierres centrales au niveau profond . Cet article donne une référence utile pour l’étude du ‘ problème d’indivudualité’( ou les situations anormaux) dans les données surveillantes de la déformation des pierres centrales de la génie civile.

Jan 1, 2003

By S. -H. Chang, C. -I. Lee, Y. -K. Lee

Based on results from triaxial compressive tests, an experimental damage model to simulate post-peak behaviours as well as nonlinear behaviours before peak strength was developed. In order to consider pre-peak behaviours, variations of elastic constants at each damage level were regressed by functions of confining pressure. In addition, post-peak behaviours were simulated successfully by using Hoek-Brown constants. As results, the experimental model could predict nonlinear behaviours, peak strengths and stiffness changes observed in experiments. Basé sur des résultats des essais compressifs à trois axes, un modèle expérimental de dommages pour simuler des comportements de poteau-crête aussi bien que des comportements non-linéaires avant la force maximale a été développé. Afin de considérer des comportements de pré-crête, des variations des constantes élastiques à chaque niveau de dommages ont été régressées par des fonctions de pression d'emprisonnement. En outre, des comportements de poteau-crête ont été simulés avec succès en employant des constantes de Hoek-Brunes. Comme résultat, le modèle expérimental a pu prévoir des comportements non-linéaires, des forces maximales et des changements de riidité observés dans les expériences. Auf Basis der Ergebnisse des dreiaxialen Drucktests wurde das experimentelle Schadensmodell, das sowohl das nicht-lineare Verhalten vor der maximalen Stärke als auch das Verhalten nach der maximalen Stärke simulieren kann, entwickelt. Um das Verhalten vor der maximalen Stärke zu berücksichtigen, wurden die Veränderungen der elastischen Konstante bei dem jeweiligen Schadensniveau durch die Funktionen des begrenzten Drucks zurückgegangen. Außerdem wurde das Verhalten nach der maximalen Stärke unter Benutzung von Hoek-Brown Konstanten erfolgreich simuliert. Schließlich konnte das experimentelle Modell das nicht-lineare Verhalten, die maximale Stärke und die Veränderungen bezüglich der Steifigkeit während der Experimente voraussehen.

Jan 1, 2003

By S. F. Burks

"This paper develops themes explained at two SAIMM platinum conferences. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can be increased significantly, usually even before the expenditure of significant amounts of project capital. Recent studies of NPV have aimed to simultaneously evaluate the impact of the optimized financial solution on the non-financial features of a project or operation.The case study presented comprised a commercially orientated review of the prefeasibility study designs and cost estimates of a platinum group metal (PGM) project in South Africa, followed by value chain optimization and sustainability studies of the project carried out simultaneously to identify potential value uplifts to be gained and guide the owners’ team going forward into the feasibility study phase. Some of the major aspects of the project that were found to have significant potential to add value included enhancement of the business model by the application of activitybased costing and theory of constraints, focus on the highest net value portions of the orebody in the early years of production, enhanced and optimized scheduling of the underground mining operation, application of dynamic grind and percentage mass recovery from ore to flotation concentrate (also known as percentage mass pull) to optimize revenue, application of elevated cut-off grades early in the life of mine, matching of the mining and processing capacity, expansion of the operation subject to capital availability, and installation of downstream processing facilities subject to regional third-party capacities.The investigation of non-financial project features focused on demonstrating that a financially optimized solution could also have a number of other benefits. These are mentioned briefly in the paper, which aims to present the status of the project at an early stage of its development."

Jan 1, 2016

By T. R. Curr, W. A. Gericke, J. Basson

South Africa is a leading player in the international ferro alloys industry. Historical factors that have contributed to this dominant position include an abundance of natural resources and relatively low cost electricity. A number of relatively recent developments are potentially threatening this position. These include new legislation affecting the mining and minerals industry, a shortage of some types of suitable reductants, depletion of surplus electricity generation capacity with resultant threat of real escalation of electricity prices and pressure resulting from the recent strengthening of the South African Rand. The industry is addressing these challenges in a number of ways to ensure long-term viability. Some of these measures include investments in more efficient technologies that have economy of scale benefits and are less dependent on expensive reductants and electricity. Local macro-economic impacts include new legislation regarding ownership of enter-prises, mineral rights and royalties on mineral sales, development plans for port and rail infrastructure, as well as initiatives to expand electricity generation and coke production capacity. The fundamentals for being a successful ferro alloy producer are still largely in place for South African producers. Therefore the South African ferro alloy industry will remain competitive and is well placed for continued growth in line with the international growth in ferro alloy demand. The industry should emerge leaner, more efficient and ready to respond to any future demands of the industry. This paper will cover the present status of the industry, the factors that are impacting thereon and a view on its future outlook.

Jan 1, 2007

By F. Pinto, J. V. Lemos, A. Sousa, L. Ribeiro e Sousa

The Rossio railway tunnel was built in 1890 crossing several formations involving limestones, basalts and also sandy and clayey formations. Due to the fact that it is an old underground structure rehabilitation and repair works were performed, namely at Km 0,900 and in a zone crossed by a new tunnel from the Lisbon Metro. Reinforcement support systems were designed in the Rossio tunnel in order to prevent its stability. In this paper, repair works and anchor tests performed at km 0,900 are presented, as well as the monitoring system implemented in order to observe the structural effects induced by the construction of the works. For the interpretation of the obtained information complex 3D models was built, permitting the simulation of the sequential excavation scheme used, non-linear behaviour of the different formations, and the support systems used. Der 1890 erbaute Rossio Eisenbahntunnel durchoertert mehrere Formationen, einschliesslich einer Kalkstein-, Basalt- sowie einer sandigen und tonigen Formation. Auf Grund des Alters des unterirdischen Bauwerks wurden Instandsetzungs- und Reparaturarbeiten im Bereich km 0,900 sowie im Kreuzungsbereich mit einem neuen Tunnel der Lissabonner U-Bahn durchgeführt. Aussteifungssysteme wurden entworfen, um die Stabilität des Rossio Tunnels zu gewährleisten. Im Folgenden werden die Instandsetzungsarbeiten und Anker Tests im Bereich km 0,900 sowie das Messystem zur Ueberwachung der strukturellen Auswirkungen der Bauarbeiten dargestellt. Zur Interpretation der gewonnenen Informationen wurden komplexe 3D Modelle entwickelt, die eine Simulation des Bauablaufs und die Anwendung nichtlinearer Stoffgesetze fuer die verschiedenen Formationen und Aussteifungssysteme ermöglichten. Le Tunnel ferroviaire du Rossio a été construit en 1890, traversant des différents terrains comme des calcaires, des basaltes et aussi des formations limoneuses et sableuses. Dû à l’ancienneté de l’ouvrage, des travaux de réhabilitation et réparation ont été faits, nomment au km 0,900 et dans la zone traversée par le nouveau tunnel du Metro de Lisbonne. Des systèmes de support renforcé ont été conçus pour le Tunnel du Rossio de façon à rassurer sa stabilité. Dans ce papier, on présente les travaux de réparation et les essais d’ancrage réalisés au km 0,900, et aussi, le système d’auscultation mise au point pour l’observation des effets structuraux induits par les travaux. De façon à interpréter l’information résultant de l’observation, des modèles 3D complexes ont été utilisés, permettant la simulation de la méthode séquentielle de l’excavation, du comportement non - linéaire du terrain et, aussi les systèmes de support utilisés.

Jan 1, 2003