Search Documents

By G. H. Gronhovd

The U.S. Geological Survey estimate of the total remaining reserves of lignite in this country as of Jan. 1, 1967 was about 448 billion tons. This represents 27 percent of the total coal reserves on a tonnage basis and about 17 percent on a thermal basis. Approximately 98 percent of these reserves are in a vast lignite field located in western North Dakota and eastern Montana. This field also extends north into the Canadian province of Saskatchewan. Despite these large reserves and relative ease of mining by stripping operations, lignite production historically has accounted for less than 1 percent of the national total. This is largely due to the fact that the lignite deposits are located in an area that has no large centers of population and the economical radius of transportation is limited by its relatively high moisture and low heating value. Commercial utilization of North Dakota lignite for power production became firmly established in the mid-1920's with the development of the first successful lignite-burning equipment. Most of the early lignite-fired boilers were equipped with spreader stokers, but as the size of the plants increased, pulverized-coal firing became the more popular method, and with few exceptions, the plants built during the past 15 years are pc-fired.

Jan 1, 1968

By Ehab Gomaa, K. A. El‑Nagdy

Backfilling material such as tailing (mine wastes) mixing with cement or gypsum has grown throughout the world’s underground mines. However, despite their growing popularity, the typical hydraulic and mechanical fill types utilized in many mines still exist. Deep underground mining has increased due to the lack of commercial minerals nearby. Mine wastes were considered the main part of backfilling to prevent environmental pollution, ground subsidence after mine abandonment, and mine collapse during deeper extraction phases. The cemented backfill technique is the principal technique used in underground mines, which include cement with fly ash and/or filter dust, cement with tailing material and fly ash, gypsum with fly ash, and synthetic anhydrite with fly ash and have been reviewed. It has concluded that a backfilling material must be selected based on further goals, available material near the mine site, and economic factors. This paper analyzes different backfill material mixtures to create a technique that will increase safety in underground mining conditions and foresees an appropriate formula that gives high uniaxial compressive strength. The multiple linear regression (MLR) on the collected data from the experimental works to construct the relationship between the uniaxial compressive strength (UCS) of the mixture and the components of the backfilling and the prediction formula for expected compressive strength was obtained. The results revealed that the predicted regression equation was robust and reliable to predict the (UCS) for the new components of the filling (cement (CE), filter dust (FD), water content (WC), and time (T)).

Oct 3, 2023

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By Hans W. Schreiber

Most geologic and mining engineering consulting firms* began to experience the recession with declining billing levels, number of inquiries, and proposal requests in late 1981 or early 1982. As of today, most of them have been functioning at reduced income levels for nearly a year. And while many consulting firms have apparently reached a stabilized income level, they can see little prospect for attaining normal (pre-late 1981) billing levels and income for the remainder of 1983. A few firms have escaped being affected by the recession. Such com panies almost without exception are small (fewer than 20 personnel), offer a limited range in technical capabilities, and tend to be highly specialized in a particular niche. They include those specializing in the heap leaching of precious metals ores, in ground water testing programs, and in the derivation of computer-aided programs to monitor particular mineral processing functions. Those firms affected by the economic downturn have instituted a variety of policies and undertaken actions to cope with significantly reduced incomes to bring fixed costs in line with the depressed demand for services. These changes fall into the following broad categories: • management and management practices; • markets and market definition; • marketing and the pursuit of assignments; and • administration and personnel relationships. Not all of the perceived changes have necessarily been instituted by every consulting firm, and any one appears sporadically instituted. Management and Management Practices In favorable times the managers, and often the owners of the equity, of consulting firms tend to concentrate their attention on the part of the business they find most satisfying and enjoyable. For some, this means acting as project or assignment leaders, even undertaking a specific technical aspect of the job. For others, it means constant marketing with the associated heavy travel and entertainment schedules. In unfavorable conditions, such as the current recession, managers tend to spread themselves far more thinly, expending time and effort on all facets of the business including marketing, proposal preparation and cost estimating, budgeting, general administration, accounting and cash flow monitoring, project/assignment overview, and actual client work. The manager who in favorable times concentrated on client work is now less billable. The manager who concentrated on marketing is somewhat more billable. The manager now needs to pay attention to and expend equal effort on each facet of the business just to keep all the facets in relative balance. Falling behind schedule on a client job or carrying an unduly large percentage of accounts receivable exact a cost to the firm. Clearly the absolute cost to the firm is the same whether demand for service is good or slack. But in periods of slack demand the firm is frequently less able or even unable to bear such costs. Marketing and Market Definition Markets appear to have undergone some significant changes: • Federal and state governments have assumed a greater importance as providers of work vis-a-vis both industry and private groups. • Projects with increase-in-capacity aspects have given way to projects with maintenance or reduced operating cost aspects. • Projects searching for new deposits of minerals in generally new locations have given way to projects reviewing known mineral districts or known deposits. • Industrial mineral and mining companies have exhibited a great propensity to cut back the use of consultants and to undertake as much work as possible in-house. Further-more, a number of industrial mineral and mining companies have entered the competitive arena with consulting firms, submitting proposals (usually to the federal government) in an effort to keep their staffs intact and occupied. In response, consulting firms have reevaluated their capabilities by reviewing old work and reassessing personnel. The purpose is to broaden the services offered and the potential client base, thus redefining the available market. For example, a firm specializing in assessment of technical and cost parameters of a deposit would normally assist a prospective lender in judging the deposit's suitability for project financing. That same company could easily expand into the field of analyzing production costs for an individual operation -something that is needed in periods when lower prices reduce profit margins. Similarly, a firm that has confined such economic assistance to commercial banks could expand to provide its expertise to other lending and even equity buying in-stitutions such as insurance companies. Marketing and the Pursuit of Assignments With few exceptions, consulting firms have significantly increased their

Jan 2, 1983

By Stephanie Singarayer, Damodara Reddy Chinnasane, Mike Yao, Danielle Pelletier

Mining at Vale’s Creighton Mine has been active for nearly 120 years in Sudbury, Ontario, Canada. Being the deepest mine in the Sudbury region, mining induced seismicity is a common occurrence at Creighton Mine. Over the past five years, 26 large magnitude seismic events ranging from 2.5 Mn to 3.7 Mn (Nuttli) have occurred. Out of these large magnitude events, three 3.0+ Mn events occurred between April 2020 and January 2021. The majority of the 3.0+ Mn events are believed to be the fault-slip type that could be linked to the known major geological structures and/or long-term effect of mining over many years. The recent large magnitude events are believed to be triggered by high induced stresses while mining the first few stopes of a new lower horizon in the top-down centre out mining sequence.

Apr 26, 2022

By Jozef F. Zurawski

Increasingly new interceptors or new Combined Sewer Overflow (CSO) projects require connections to existing tunnels. More often than not, the existing facilities are old, in poor or questionable conditions, without proper construction records or as-built drawings. Many cannot be easily inspected unless major construction effort provides flow by-pass for safe access. This paper provides general guidelines on how to approach the problem of assessing the condition of old tunnels, how to plan and design the connection with limited physical assessment, how to develop the scope of work for the bid documents and how to provide geotechnical guidelines and designs for the bid documents.

Jan 1, 2008

By AJIT SWAIN, SUNATI MOHANTY

The abstract discusses the importance of predicting the dewatering performance of industrial hydrocyclones from laboratory models. It highlights the challenge of scaling up design and operating parameters for efficiency estimation. The paper describes experiments with a 2-inch and 4-inch hydrocyclone using silica sand. It details the development of a model using the Nageswararao hydrocyclone model and a simulator to estimate model parameters. The model is validated with experimental data, and a new model is developed using 4-inch hydrocyclone data. The technique is then extended to predict dimensions for a full-scale dewatering cyclone operating at higher throughput and solid concentration.

Mar 30, 2022

By R. W. Lake

The decision to develop an ore body can lead to multi-million dollar profits, or equally substantial losses. Accordingly, the effort required to adapt a valuation model to the specific proposal at hand, or even the development of a new model from basic principles, is clearly warranted. In the formulation of a model of this nature, one is faced with some major questions. For example, with the long term obligations that it implies, on what basis should a decision to initiate mining operations be made? Furthermore, how can the vagaries of inflation and the uncertainties that shroud the future be accommodated? Beyond the general principles by which mineral deposits are evaluated, specific cost behaviour is a function of the geology of the deposit, and of the mine design. Moreover, mine design, during the life of the mine, must be a continuing process somewhat akin to dynamic programming. An initial, apparently optimal, design is selected and mining commences. With production, a continual process of information updating leads to revisions. Thus if the maximum value is to be obtained, the mine design must be adjusted to conform to the changed conditions.

Jan 1, 1977

By Jerry Dolph

In September 1855, 55-year-old Noah Spencer Kellogg and his $3 jackass named Bill discovered what was known at the time as a “blow out” of high-grade lead and silver ore. The deposit was located on the side of a North Idaho mountain high above the South Fork of the Coeur d’Alene River. The ore was later assayed at 41,141 g/t (1,200 oz/st) silver. Kellogg named his discovery the Bunker Hill Lode, after the June 17, 1775 Revolutionary War battle of Bunker Hill. A thriving pioneer settlement sprang into existence around the resulting mine’s workings and was eventually— and appropriately — named Kellogg. The peak rising hundreds of feet above the mine’s adit was named “Jack-ass Peak” after Noah Kellogg’s hairy companion.

Jan 1, 1996

By E. A. Metz

Perfect combustion in an engine would produce only water vapor, carbon dioxide and nitrogen as by-products; however, complete combustion is never achieved. As a mobile power plant, the diesel engine is relatively inefficient in terms of energy produced from the energy potential of the fuel. The diesel is not a perfect engine. The fuel burned can undergo a very large number of reactions in the combustion chamber. It only stands to reason that a large number of compounds are contained in the exhaust, actually, thousands of chemicals. The exhaust can be broadly divided into a gaseous phase and a particulate phase. Each phase is made up of organic and inorganic compounds. The vapor phase contains carbon monoxide, sulfur dioxide, various oxides of nitrogen and many hydrocarbons. The particulate phase contains clusters of respirable inorganic particles made mostly of carbon. This paper will address the health hazards, as we know them today, of the major components of the particulate phase in the exhaust of diesel engines. It will briefly examine the operational factors of the diesel engine as it applies to particulate emissions. Longitudinal studies of occupationally exposed miners are needed with documentation of levels of exposure before a chronic effect of exposure can be determined. At this time, it is not possible to conclude from human studies the level of diesel exhaust exposure that results in the observed lung cancer risk.

Jan 1, 2001

By Thomas E. Ban

During recent years fuel consuming industries of the United States have been caught between environmental restrictions and the uncertainty of obtaining an inexpensive fuel. With the advent of the National Energy Act of 1978 there has been added impetus to switch from gas and oil to coal. For industrial furnaces and boilers that were designed to bum coal, returning to an available compliance coal might be feasible. However, furnaces and boilers designed for gas or oil cannot reasonably be converted to coal unless the coal is initially gasified. All cases, nevertheless, depend upon the availability of an adequate structured coal of a compliance composition, a challenge to the coal mining industry. The foregoing problems have contributed to the current energy-coal crisis of today's economies. It therefore would be worthwhile to capitalize on previous experiences of the mineral processing industry.

Jan 1, 1979

By J. Geyer, B. T. Burton, H. W. Newcomen

For open pits developed in tropical climates the upper portions of the pit walls are often located in residual soils and weathered rock. Due to the presence of relict structures, and the relatively low strength of the residual soils and weathered rock, design slope angles in these materials have to be developed by blending the results of kinematic assessments of geologic structures with rock mass stability analyses and traditional soil mechanics. Background information on the engineering considerations of residual soils are discussed, and the results of geotechnical assessments for proposed pit design of the Brisas del Cuyuni Project, located in southeastern Venezuela, are presented.

Jan 1, 2000

The failure of a seal in an underground coal mine can have devastating consequences. Traditionally seals have been constructed as flat walls. Large hydraulic dams, on the other hand, are constructed as concave arches. This paper presents an initial analysis of the potential strengthening of seals by concave construction as well as the impact of additional cost in terms of labor and material. A simple finite element analysis of three-dimensional solids under uniform loading allows comparisons between the strength of a flat wall and a curved arch. The models are examined for reasonable behavior and displacements at 20, 50, 100, and 200 psi loads.

Jan 1, 2007

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By Jon Y. Kaneshiro, Ed Walton, Stephen J. Navin, Robert M. Sergeant, Storer J. Boone

The Coronado Traffic Tunnel is a proposed two-lane, reversible, road tunnel, which will relieve severe peak hour congestion problems on surface streets. The tunnel will take traffic from the Coronado Bay Bridge to Naval Air Station North Island. The project will include 12.5 m (41 ft) inside diameter by 1,112 m (3,650 ft) of tunnel, 552 m(1,815 ft) of cut and cover box structure, and 400 m (1,315 ft) of open cut structure. The geology consists of predominately clean and silty sand, saturated sand, with some clay layers, requiring Earth Pressure Balance or Slurry Shield tunneling technology.

Jan 1, 2001

By L. E. Mercando

The proposed Flambeau Mining Project is based on a high grade copper deposit located approximately one mile southwest of Ladysmith, Wisconsin. The project involves only the mining, crushing, and shipping of ore to facilities outside of Wisconsin for processing. The Wisconsin environmental regulations include provisions for identifying wetlands, the requirements for minimizing the disturbance of wetlands, and the need to establish new wet-lands to replace any wetlands which have to be disturbed.

Jan 1, 1991

By Paul A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County constructs twin Tunnel Boring Machine (TBM) tunnels through cohesive soils and rock beneath the Allegheny River and a narrow city street in Pittsburgh, PA. The tunnel alignment includes an historic building on shallow foundations, modern buildings on deep foundations, and an office building constructed directly over the alignment during the design of the tunnel sections. This paper provides an overview and update of the general site conditions, TBM tunnel design, and support of excavation for the TBM launching pit. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed.

Jan 1, 2008

By Valerie (Wollet) Rebar

Successful execution of fast-track projects is an arduous task at best. Effective and organized management, a comprehensive technical design with an independent check-and-balance system, and optimal schedule components all play major roles in project success, regardless of the required timeline. However, a fast-track schedule intensifies the significance of each of these elements due to the heightened time constraints.

Jan 1, 2008

By E. P. Deliac

The aim of this joint work between the French Coal Board and the Paris School of Mines is to be able to practically model the behaviour of a transverse drum cutting rock with picks. First a theoretical approach leads to the concept of cutting curves, giving forces and torque against penetration per drum revolution. Then experimental evidence, from full scale and reduced scale testing, validated and confirmed the theoretical shape of the curves. Finally practical applications are given, to improve the design or use of a shearer (or continuous miner). A micro-computer program is being developed to predict the cutting performances of a machine in certain conditions.

Jan 1, 1985

By E. Hsieh

Proximity detection in the open pit mine can be used effectively as an operator assist strategy which improves digging production through enforcement of best practices, although it is normally thought of first as a safety tool, and second as a step toward full automation when combined with object avoidance.

Feb 23, 2014