Search Documents

By J. MacFadyen

The U.S. cement industry, including Puerto Rico, again set a record in terms of production and shipments. The increase in shipments came primarily from imports of portland cement as domestic production from produced and imported clinker gained only 1.9 Mt (2.1 million st). Clinker production as reported to the U.S. Geological Survey (USGS) was 88.6 Mt (97.6 million st), an increase of 1 percent. Gray and white portland cement production from domestic and imported clinker, estimated at 93.5 Mt (103 million st), was up 1.9 Mt (2.1 million st). Masonry cement shipments of 5.5 Mt (6 million st), which equates closely to production, was up 6.3 percent. Blended ce-ment shipments were up 35.9 percent from 2004 at 2.35 Mt (2.6 million st).

Jan 1, 2006

The fundamental objective of mine plans are usually to maximize the mine profit by extracting ore at the lowest possible cost over the mine life while some technical constraints are satisfied. Since the costs associated with the operation of trucks and shovels as resources are significant, determining the optimum number and allocation of these resources is an essential issue. This paper presents a Mixed Integer Linear Programming (MILP) model to determine the optimum number of shovels and trucks required to meet the short-term plan?s goals. Also, the model takes into account the allocation of trucks and shovels to mining faces. This model minimizes operational costs, while attempting to meet the production demand and to satisfy technological constraints. This paper also analyzes the operations of trucks and shovels in an open pit mine using ARENA simulation software.

Jan 1, 2012

During the past decade, since the appearance of Popoff's (1966) review of grade tonnage calculations, it has become evident that defining a new method which could be followed step by step by a technician and which would improve reserve estimation was not a simple thing to do. Some concepts have emerged though, and most definitions of ore reserve now require a statement of reliability (USGS, 1975; and Zwarten-dyke, 1976). Exactly how the reliability should be computed is not a straightforward process. It also became apparent that not only was reliability a requirement but that additional questions such as how to predict mining re- serves from geological reserves were to be asked. In fact what became obvious is that specific models have to be designed for each type of mine and for each type of question which is asked. Most methods can be encased within a unique general geostatistical, model, but it takes considerable custom tailoring, and there are still questions that are left unanswered. In this chapter, before giving techniques, we intend to first review what should be required from a grade tonnage calculation done at the exploration stage. If the final objective is still to specify a tonnage and grade, with eventually a reliability, many qualifications have to be made before quoting, and of course, calculating these two numbers. Then the currently avail- able methods will be reviewed and future trends will be shown; finally a few case studies will be given and recommendations about the choice of a model will be made.

Jan 1, 1979

By J. W. Langford

A more effective method of fracturing and chipping the formation is necessary to significantly increase the productivity of blasthole drilling with a roller cone bit. The conventional rotary blasthole bit engages the formation and initiates spalls, chipping and fractures in the formation at a rate dependent on the amount of pull down force applied by the drill. The rotary speed of the drill increases the number of fractures and creates drilled chips that are removed from the hole by the air circulation. An engineering project was motivated to develop a low pressure, low impact downhole percussion hammer to provide an overstrike force to a blasthole bit, in addition to the conventional pull down force and rotary speed. The objective of the project was to utilize existing rig air packages in the range of 50-110 psig and provide an overstrike force to the bit in the range of 1100-1500 impacts per minute. Laboratory testing performed on Barre granite achieved, on average, a 40% improvement in rate of penetration. This performance has been confirmed in actual blasthole drilling in copper and iron ores mines. During the testing phase, additional unexpected benefits have also been realized.

Jan 1, 2011

By J. H. Wilhelm

Continuous thickeners can be sized either from previous experience, continuous pilot-scale test results, or from batch settling tests. Although it is a relatively simple process to size full-scale thickeners when previous experience or pilot-scale operating data are available, batch testing is often the only realistic method for sizing thickeners due to time restrictions, budget limitations and availability of sample material. Many authors have, therefore, suggested means of running batch tests and analyzing the resulting data. Fundamental thickening theory had its beginning with the work o£ Coe and Clevenger(1). In order to determine the size of the thickener settling area, they proposed that a series of batch settling tests be run at various initial concentrations. The solids handling capacity at each concentration can then be determined and the lowest capacity (maximum area requirements) used to size the thickener. Kynch(2) developed a mathematical analysis in which the relationship between solids concentration and settling rate can be obtained from a single batch settling curve. Talmage and Fitch(3), Yoshioka(4)(5) and Dick(6), have enlarged upon these works to give a basis for methods of sizing thickeners.

Jan 1, 1979

By Thomas V. Falkie

The title of this talk has brought some interesting responses - even before it was written - from different parts of the country. A geologist from the Western U. S, was deeply concerned with recent layoffs in his profession and the employment situation in general and wondered why "the AIME wasn't doing anything for the benefit of its members." A petroleum engineer in Texas said that a group in his field were studying "professionalism" and their professional status and wondered if there were any words of wisdom for him. A mining engineering professor from the East pointed out that the National Science Foundation did not include mining engineering as one of its recognized fields in one of its equipment funding programs. These are just a few examples of reactions received to date, but they serve to illustrate the broad image that the title has meant to various people. Actually the term profession is defined by Webster as "a calling requiring specialized knowledge and often long and intensive academic preparation." The word encroach means "to enter by gradual steps or by stealth into the possessions or rights of another", or "to advance beyond desirable or normal limits." The intention of this paper, as originally conceived and requested by the program chairman, was to combine those two words literally and talk about how the professional standing of mineral engineers is being eroded from people outside the profession. But the amazing preliminary response suggests that it may be timely to broaden the discussion by including some comments about professionalism in general. In the paper the terms "mineral engineer" or "mining engineering" are used frequently, but it should be clearly understood that much of what is said is valid and is intended for all fields covered by SME and perhaps for AIME in general.

Jan 1, 1972

By V. I. Lakshmanan, Dan A. Mackie

Traditional vat leaching methods have had limited success, primarily due to the high cost of loading and unloading the vats. In general, such batch methods are labor-intensive and costly. Heap leaching has emerged as a viable, low- cost alternative, but low recoveries, normally in the 70% range, offer opportunities for improvement. Also increased regulatory guidlelines for effluent and spent heap leach pads disposal offer potential for alternative methods. The Mackie Vat Leaching Jig (MVLJ) has had its incubation at Ortech International, where bench scale through pilot scale testing continues. Design developments and testwork over the past two years indicate that the time may be right for field trials.

Jan 1, 1990

By F. Schreiter

The Ore Mountains in Germany have a history of more than 850 years of underground mining activity. This has created a situation where thousands of old mine shafts and adits are due for rehabilitation. While no long-term stable rehabilitation was executed in previous centuries, those abandoned mine sites which date back to the uranium mining boom from 1945 to 1962 were rehabilitated immediately after mine closure according to state-of-the art technology. Over the years, however, it has become obvious that most of these sites are not long-term stable and thus it has become necessary to rehabilitate them a second time. Technical University Bergakademie Freiberg is carrying out a research project on the optimization of this process. 70 mine site rehabilitation projects, the technology and the materials used have been assessed. A technical guideline for future rehabilitation projects, based on the outcomes of this assessment, is under development with the goal to make it easier, faster and more economical to select and apply suitable designs and construction materials for dams, plugs and other rehabilitation structures in former uranium mines.

Feb 27, 2013

By J. Kallioinen

The development of mechanical flotation cells has resulted in larger and better cells. This has led to flotation banks with only a few units, even in large-scale operations. This equipment development makes the old operational considerations ineffective. The flotation cell must be considered as a single reactor unit capable of handling specific tasks and getting excellent metallurgical performance. The result of the unit reactor concept development was the new large TankCell that comes in sizes up to 113 m3 (4,000 cu ft). The TankCell construction includes new modified rotor-stator designs, new tank geometries and a froth-handling capability independent from subprocesses taking place in the pulp (i.e., air addition). The conventional idea of a single flotation cell type for fine, intermediate and coarse materials does not give optimal results. Optimal flotation of coarse and fine particles needs different mechanism designs, impeller tip speeds and different froth control objectives.

Jan 1, 1995

By J. S. Meyer

Although salmonid fishes (including Pacific salmon and trout) have only intermediate sensitivity to copper (Cu) for traditional toxicity endpoints (survival, growth, and reproduction) and thus do not ?drive? the freshwater Cu criteria (e.g., see species-sensitivity ranking in US EPA 2007), Cu concentrations as low as 1 to 2 µg/L have been reported to impair olfaction (the sense of smell) in salmonids in laboratory experiments using dilute fresh water (see references in Meyer and Adams 2010 and DeForest et al. 2011). Olfaction is crucial to predator avoidance, recognition of kin, and reproductive synchronization (Baldwin et al. 2003); and Cu is of general ecotoxicological concern because it can be present in acid/mine rock drainage, industrial and municipal effluents, agricultural runoff, and urban stormwater runoff (Meyer et al. 2007). Therefore, there is public concern that the current regulation of Cu in surface waters is not stringent enough to protect salmonid fishes against olfactory impairment (e.g., OSU 2007; Pearson 2007). Because the toxicity of metals to aquatic organisms is a function of water chemistry [e.g., acute toxicity of Cu generally decreases as pH, water hardness (Ca2+ + Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase; Meyer et al. 2007], hardness-based freshwater criteria for metals are lower at lower water hardness. The recently-developed biotic ligand model (BLM) explicitly takes into account all four of those water chemistry parameters and the concentrations of other major inorganic cations (Na+, K+) and anions (Cl-, SO42-) to predict the acute toxicity of cationic metals (e.g., Ag, Cd, Cu, Ni, Pb, Zn) to aquatic organisms; and the BLM has been adopted by the U.S. Environmental Protection Agency (US EPA) to calculate acute and chronic national freshwater criteria for Cu (US EPA 2007). Consistent with observations of Cu toxicity to aquatic organisms, BLM-based Cu criteria generally are lower at lower pH, water hardness, alkalinity, and DOC concentrations. Therefore, although threshold concentrations for olfactory impairment by Cu can be low in dilute fresh waters, the corresponding hardness-based and BLM-based Cu criteria for the same waters also tend to be low. This leads to a logical question: Are Cu criteria already protective against impairment of olfaction in salmonid fishes, thus obviating the need to decrease those criteria even lower to protect against adverse effects to this physiological/ecotoxicological endpoint? Herein, we demonstrate that in all studies conducted to date, the US EPA?s BLM-based freshwater Cu criteria would have been protective against olfactory impairment in salmonid fishes, but the US EPA?s hardness-based criteria would not always have been protective. This distinction is important because all 50 States in the USA still use hardness-based Cu criteria in their water quality standards, and only some of the States allow use of the BLM to calculate site-specific Cu criteria. Additionally, in the absence of empirical results for calibration of a saltwater Cu-olfactory model, we demonstrate that a proposed unified freshwater-saltwater Cu-olfactory BLM predicts the US EPA?s current saltwater Cu criteria would be protective against olfactory impairment caused by Cu in sea water.

Feb 27, 2013

By Philip R. Whitney

Precipitation of hydrous manganese/iron oxides in streams can be readily observed in much of the northeastern United States, and is apparently a common phenomenon in other glaciated areas (1,2,3,4). Deposition occurs when Mn-enriched ground or surface water enters the stream environment and encounters conditions of higher Eh and pH. The preferred location for deposition is in shallow, fast-flowing segments of stream; the oxides usually form as coatings on detrital material. The experimental studies of Hem(5) and a considerable amount of work on marine and lacustrine manganese nodules(6,7,8) suggest that given an appropriate substrate, deposition of manganese oxides may occur even when the water is undersaturated in Mn with respect to the oxides, due to catalysis by organisms or by silicate, carbonate, or ferric hydroxide surfaces. Once begun, manganese oxide deposition is autocatalytic (9). Studies of the distribution of oxides in various size fractions of stream sediments indicate that the thickness and prevalence of the coatings commonly increases with increasing particle size in the coarse sand and gravel size ranges. Figures 1 and 2 show a fairly typical distribution of leachable metals over nine size fractions from 62 microns up to 8-16 mm. The leaching solution used was neutral ammonium citrate with hydroxylamine hydrochloride, which effectively removes the oxide coatings without significantly attacking most silicates, carbonates or sulfides. Figure 1 shows metal content as ppm of the total sample; figure 2 shows' the same data as micrograms of metal per square millimeter of surface area.

Jan 1, 1975

By J. W. Craven, M. Katom, K. M. McCaffery

At Ok Tedi, ore type and SAG feed size distribution vary widely and frequently. This makes control of the SAG mills by application of the power/pressure relationship difficult. Power logic has traditionally been conservative due to power spikes associated with rapid size distribution changes. A new expert system was installed in early 2000. The system incorporates multiple state fuzzy logic to deal with frequent and radical ore type and size variations, along with monitoring of motor temperatures. A short term power spike no longer warrants immediate radical action. This has resulted in increased mill throughput and improved circuit stability.

Jan 1, 2001

By Alan Weakly

The Powder River Basin (PRB) of northeastern Wyoming and south-central Montana is the largest strippable reserve of compliant coal (0.6 or less lb of sulfur per million Btu) in the United States. In mining parlance, it is the Mother Lode! Wyoming’s portion of the Basin provides one fifth of the coal produced in the United States annually, and the state has been the nation’s top coal producer for the past six years. Based on 1993 production statistics and estimated strippable compliance coal reserves, Wyoming may remain the nation’s top producer for the next 76 plus years. Past articles on the PRB have focused mainly on production. After living and working in the Basin for the past five years, I have developed an appreciation for the area and its major industry that transcends size and production data. In the fall of 1993, MINING ENGINEERING’s publisher and I decided to present a series of articles that would cover many other aspects of the Basin. Ten topics were outlined, and specific individuals, selected for their knowledge and experience, were asked to contribute articles about their specialties. Although Montana has four large mines producing coal from the PRB, this series of articles will concentrate on the Wyoming portion of the Basin.

Jan 1, 1994

By S. Lin, Y. J. Wang

Based on systematic definitions of a generalized multiple fan ventilation system, the concepts of an augmented system, its solution curve and the operating points of the original system are introduced. The Quasi-Newton algorithm is applied in combination with the switching-parameter method to ensure a continuous search along an augmented-system solution curve and identify all the possible system operating points on it. Two example networks are analyzed to demonstrate those concepts and the application of the algorithm for identifying operating points of multiple fan ventilation systems.

Jan 1, 1994

By R. Dillinger

In the environmentally conscious social atmosphere today, reclamation in surface mines has become a main issue to the public and the regulatory committees. In response to this increased attention, many regulatory committees have begun to enact more stringent regulations on surface mining operations. Operations across all spectrums of the industry have seen changes. Recently and most visibly the mountain top removal mines have seen several new regulations focusing on environmental protection. Specifically regulatory committees have emphasized a focus on the methods of reclamation and recovery of layers suitable for vegetation. These layers are the most visible once the operation has concluded. Also, these layers have the most human interaction (farming, hunting, and house development). Often times the new regulations enacted are shifting from a performance base to a standards base. The key differentiator being a performance base dictates the final result while a standards base dictates the method to achieve the result. The very nature of many regulations (especially those that are standards based) not only challenges the physical limitations of the equipment used today, they come with a financial impact. For the purpose of this paper, the model will be a surface coal operation, utilizing draglines as primary overburden movers. The coal seam is ten feet thick, the overburden ninety five feet thick, the pits are 150 feet wide, and the dragline is a Bucyrus Erie 1570.

Jan 1, 2011

By B. A. Kennedy

The instrumentation, monitoring, and prediction of a major slope failure at the Chuquicamata mine are described. In December 1967, pre-existing tension cracks on the south end of the east wall of the Chquicamata mine began to open. Various forms of instrumentation were installed for continuous monitoring. These systems included tension crack stakes, crack extensometers, linear extensometers, tape and transit lines, sliding wire contacts, and a seismograph. From the information obtained, the failure date was accurately predicted some five weeks before failure, enabling the mine to reroute truck and rail access; hence, causing a minimal mine shutdown of two and one-half days and preventing any injuries to persons or damage to equipment. The shape and form of the sliding mass are analyzed, as are the possible modes of failure.

Jan 1, 1970

By Yuemin Zhao, Daniel Tao, Xinxi Zhang, Qingru Chen, Maoming Fan, Zhenfu Luo, Xiuxiang Tao, Guohua Yang

Coal is currently cleaned with the minimum of size reduction, fine particle processing, recovery, and tailings disposal are major problems. Adequate water resources are not always available. For example, two thirds of China's coal is located in arid areas. Hence, dry separation provides an alternative approach. Of the dry coal separation methods available, air dense-medium fluidized beds have been used to separate 50~6mm coal efficiently. However, excessive bubbling and back mixing of the separated solids in the air-dense media fluidized bed causes the high lower size limit of 6mm for the feed material, this affecting the preparation efficiency. Based on prior study on air-fluidized dense media for 6~50mm coal preparation, this paper presents methods and test results on the fine coal dry classification, static electricity beneficiation of 0~0.5mm coal, and magnetically stabilized fluidized beds for separating 0.5~6mm coal.

Jan 1, 2005

By Mogens Henriksen

In the past decade, numerous urge scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in Figure 1. Allen1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs2. His data, however, do not reflect sensitivity of flowrate to air/water ratio. Further, in Gibbs' work, air apparently is injected continuously along the column of water. This configuration differs from that used in reverse air lift drilling where air is injected at discrete points only. Gas lift theory has received considerable attention over the past decades. Orldszewski3 defined flow regimes in two phase flow. Griffith and Wallis4 determined relative velocities of gas to liquid. Two-phase flow has been studied extensively for oil transport in inclined and vertical pipes by Chierici et a15, Beggs and Brill6, and Gould, Tek and Katz.7

Jan 1, 1977

By Jodi Banta

Thanks to strong industry support and longstanding partnerships, the University of Arizona has provided extensive pre-college mining education and outreach for more than a decade. These efforts to promote mining-related degree programs and the wide variety of indemand career opportunities reach thousands of middle and high school students and hundreds of teachers every year. The School of Mining Engineering & Mineral Resources is constantly looking at ways to help students overcome barriers into degree programs. But competition among degree programs for talent is fierce, and outreach has not made a big enough difference in the number of students pursuing mining engineering degrees. With workforce shortages threatening to undermine the industry, more is needed. The Bureau of Labor Statistics estimates 500 new mining engineering jobs each year, and according to a study by Deloitte (2023) nearly 50 percent of skilled engineers will reach retirement age in the next decade. At the same time, the 14 accredited mining or mineral engineering degree programs in the United States are producing fewer than 200 graduates annually (Society of Mining Professors and Society for Mining, Metallurgy & Exploration, 2021). To better understand mining’s competitive position, the School of Mining Engineering & Mineral Resources conducted a comprehensive study to determine (1) how prospective college students, parents and educators perceive the industry, related careers and the mining engineering degree, (2) factors affecting students’ choices of degrees and career plans and (3) the roles parents and educators play and how they influence students. This article is the first of two installments to discuss the results. This installment focuses on what students, parents and educators think about mining and where they get those impressions, as well as the role parents and educators play in influencing students’ choices of careers and degrees. The second installment, scheduled for publication in a later issue of Mining Engineering, looks at what students are seeking in their degrees and careers, and how mining compares with other degrees and industries.

Sep 1, 2025

By C. E. Stack

For the purposes of this presentation, "refractory clay" is intended to include any clay suitable for refractory products and thus represents a description based on industrial application. Other common examples based on use would be white-ware clay, bleaching clay, paper clay, or cement clay. Most users and producers of refractories have specific quality requirements which determine the quality or type of clay that can be utilized. Many clays can however be interchanged or substituted in use by changing manufacturing processes or upgrading less desirable clays. U.S. Bureau of Mines publications (Ampian, 1985) categorize days into six groups. These are kaolin, fire clay, ball clay, bentonite, fuller's earth, and common clay. These are practical groupings based on clay production and usage in the United States. Among these groups bentonite, fuller's earth, and common clay are primarily composed of the minerals, smectite, illite, or chlorite, and are non-refractory. Kaolin, ball clay, and fire clay are commonly used in refractories and thus qualify as refractory clays.

Jan 1, 1986