Search Documents

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Chen-Luh Lin, Jan D. Miller

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of centimeter size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of millimeter size. Based on Micro-XCT, it was expected that 85 percent of copper for sample A could be recovered at 65 percent of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual-energy X-ray radiography was used as a basis for sorting. Pilot-scale X-ray sorting of sample A (10 × 1 cm) showed 31 percent rejection of a 0.08 percent Cu gangue product with a corresponding recovery of 90 percent copper.

By M. Irish, M. Jahraus

Accurate prediction of gold (or other metal) production from a heap leach operation is essential to the economic vitality of any such operation. However, this is also one of the most challenging issues facing managers of these facilities. Three approaches to modeling gold production from the Valley Leach Facility (VLF) at Anglogold’s Cripple Creek & Victor Gold Mining Company are presented. Evolution of these modeling methods has been necessary as ore heights and volumes have increased. In addition, the complex geometry of the VLF presents additional complications to production modeling, Comparison of actual and predicted gold production are presented

Jan 1, 2001

By W. G. Pariseau

Reliable stress measurement using hollow inclusion gauges and monitoring stress change using borehole stress meters and borehole deformation gauges in anisotropic rock remains a challenge for the rock mechanics community. In this regard, the complex variable method advanced in 1983 for deducing stress in anisotropic rock is flawed and software is privileged. Fortunately, advances in computer hardware and software now enable fast, reliable reduction of hollow inclusion stress measurement data for determining stress in anisotropic rock. Monitoring stress change in anisotropic rock poses a different challenge but is also subject to numerical analysis. Stress measurement using a hollow inclusion (HI) gauge such as the triaxial Australian HI is done in four steps: 1) drilling a measurement hole, 2) installation of an HI, 3) stress relief of the HI by overcoring, and 4) data reduction. The last step, data reduction, is the focus of this work. The process is well-known in linearly elastic, isotropic rock (Worotniki and Walton 1976, Duncan Fama and Pender 1980). However, in case of linearly elastic, anisotropic rock the requisite technology is not readily available. This situation is somewhat surprising because anisotropy is more often the rule rather than the exception, especially in the neighborhood of ore bodies. Rahn (1984) has pointed out the potential for significant errors with neglect of anisotropy and the adverse consequences for engineering design. Amadei (1984) has also pointed out the potential for errors with neglect of anisotropic rock properties in stress measurement. Worotniki (1993) cites other studies that indicate potential for serious errors when doing measurements in anisotropic rock. In both theoretical cases (isotropy and anisotropy), data reduction is essentially a composite of solutions to boundary value problems in linear elasticity. In the finite element approach, the analysis is a simulation of gauge hole drilling, installation and overcoring. Two important advantages with the finite element approach are a more faithful representation of the conditions of HI stress measurement than approximated in theory and the capability for handling rock whether isotropic, transversely isotropic or fully anisotropic

Mar 2, 2022

By I. Raposo, I. Moreno-Ventas, A. Palma, M. J. Díaz, M. Vázquez

The oxidative degradation kinetics of chalcopyrite have been studied by thermogravimetric analysis (TGA). The obtained data are necessary for the kinetic description of the flash fusion process, which can contribute to the optimization of the smelting process in copper extractive metallurgy. Activation energy (Ea) evolutions of the involved processes have been determined by several isoconversional methods; in this sense, the chalcopyrite oxidation processes could be adequately described, among studied models (E1641–16, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman), by the Kissinger–Akahira– Sunose kinetic model. Using this method, Ea and A values are found to be very dependent on the conversion. Under lower conversion levels, higher Ea and A values have been calculated with respect to that found for medium and higher conversion levels.

By J. V. Ghelarducci, M. A. Sharpe, D. G. Chedgy

This article presents a novel design, called the Climax, High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 ~ 660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax, magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Feb 24, 1997

By E. Z. Casassa

There has been a recent revival of interest in concentrated coal/water slurries as a substi¬tute for fuel oil or for coal/oil mixtures, particularly in electric power generation. The idea is not a new one. Coal/water slurries were transported by pipeline in the U.S. in the early nineteen-sixties, and the Black Mesa coal pipeline has been in operation for several years, while in Germany, coal/water slurries were being burnt for power generation in the early nineteen-seventies, as described by Merten and Höner (1972). Since coal is not a pure substance but a carbonaceous mixture, the different chemical and physical behavior of coal/water dispersions from different deposits must be understood in order to optimize the properties of the result¬ing slurry fuels. Since minerals which are minor constituents of coal may also strongly affect slurry properties, coal chemistry may vary considerably even within a single deposit. Thus it is unlikely that there will be a single formula for optimizing the slurry properties of all coals, and even the answer for coal from a single source may change with time.

Jan 1, 1983

By Lawrence M. Gochioco

One of the best kept technology secrets in U.S coalmining history involved a robust coal geophysics program used by a local coal company to detect and map various geologic anomalies and man-made structures ahead of mining for nearly 15 years. Several original mine plans were changed as a result of findings from two-dimensional (2D) and three-dimensional (3D) seismic data. They indicated the presence of geologic anomalies in reserve areas that could adversely impact future mine development and longwall production. By combining the surface seismic and exploratory drilling methods, the coal company learned how to properly leverage its risk by gathering a lot of useful subsurface information before making major commitments.

Jan 1, 2005

By K. J. Ashley

Over the last six years I have been involved with the calculation of ore reserves and mine planning using various computer systems and soft- ware packages. This experience has given me a unique perspective from which to view the needs of the engineers and geologists whose job it is to produce geologic and mineable ore reserves. The purpose of this paper is to share that perspective with those who are in this field or are thinking of purchasing computer software to aid in these calculations. My first experience with computers in mining was the creation of a mini-computer based coal reserve and mine planning package written as part of my Easter's thesis. This package took about ten weeks to write, four weeks to document, and two weeks to install at the mine for which it was written. It did what it was designed to do, which was to emulate the hand procedure which had been used prior to its installation. The package was specific to its application which involved several small seams of coal being mined simultaneously and would have required major modification for it to be applied to a mine where, say, one thick seam was mined in two benches.

Jan 1, 1985

By S. P. Lewis, R. L. Sundeen

Most of us are aware of the ever increasing use of underground space. At the Advisory Conference on tunneling in Washington, D. C. in June of 1970, the demand for construction oriented tunneling during the 1970s was estimated at some 21,000 Km of length with an excavation volume of 675 million cubic meters. Of this total, 11 million cubic meters were forecast for underground parking. Though this is a small portion of the total, it is significant to note it represents a 280% increase over the previous decade. Other areas of unusual increase were railroad tunnels, 150%, and rapid transit tunnels, 160% (1). Faced with this increasing demand, the need for improved excavating efficiency is obvious. Great strides have been made. In Japan, for example, several new long tunnels have been driven parallel to old existing ones at costs as much as 50; under those of the original tunnels (1). This is an impressive achievement. I am certain, however, that we would all agree that even greater improvement is required. Great emphasis is being placed upon sophisticated systems which include among others, mechanical borers, thermal fracturing, and various methods of rock weakening and softening. However, in hard rock excavation the fact remains that the drill-blast method continues to be the most widely used system. Undoubtedly it will continue to be one of the most important techniques in the forseeable future.

Jan 1, 1974

By PEILIN LAN, LEONARD HILL, SIMON TIMBILLAH, BERNARD FOSU, CESAR SOSA-BLANCO

The use of sodium hydrosulfide (NaHS) in most of the operations in byproduct molybdenum flotation comes with safety concerns and, in some instances, a high reagent cost. Engineered solutions at the various operations where NaHS is used have immensely reduced the possibility of hydrogen sulfide (H2S) gas evolution. However, the threat of exposure remains, and this, coupled with the high dosages of NaHS consumed, supports the continued search for alternative depressants. This paper focuses on efforts to study the applicability of disodium carboxymethyl trithiocarbonate (DCMT), an organic depressant, as an alternative to NaHS. Bench-scale rougher flotation results for samples from the Sierrita copper–molybdenum (Cu–Mo) plant showed the best DCMT performance at 8 kg/t of DCMT, pH 10.5, 30 min of shear conditioning and 10 min of flotation conditioning. The Aminpro plant model simulation confirmed that 4 to 8 kg/t DCMT under certain shearing and conditioning times achieved superior or equivalent Mo–Cu separation efficiencies when compared\ to NaHS.

By S. Underwood

The tracer gas method of conducting ventilation surveys is a means of determining air quantity in underground mines with knowledge of the concentration of the tracer in the atmosphere and the flow rate at which the tracer is being released. The technique is useful in inaccessible areas of underground mines and areas where traditional point measurement of velocity is not practical. Sulfur hexafluoride (SF6) is the industry standard tracer(Kennedy 1987) used in underground mines because it is safe, stable, and not naturally occurring in the mine environment. The implementation of a second tracer will increase the versatility of the tracer gas technique allowing for simultaneous releases for the study of interrelated ventilation circuits, and for conducting multiple experiments in less time. This paper will detail the selection of perfluoromethylcyclohexane (PMCH) as a novel tracer with sensitivity, physical properties, and analysis characteristics similar to SF6. Methods for the release of liquid PMCH into underground mines will be recommended, and the vulnerabilities of sample loss due to condensation of vapor PMCH will be explored. Finally, the benefits and implications of using PMCH as a second tracer will be discussed.

Jan 1, 2012

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By M. Jessop, V. O. Kofoed, R. Blanchard, A. Hughes

Willowstick has successfully employed a new Seismic Acoustic Resonance (SAR) method to improve seepage characterization through, beneath, and around dams. SAR is a passive seismic method that detects zones of higher permeability in the foundation and fill materials of a dam. Just as the ocean has tides, the earth’s crust experiences daily “Earth Tides” and is constantly in motion. Continual motion produces resonance signals that can be measured, interpreted, and modeled to identify zones of higher permeability within a dam and its foundation. The SAR results are analyzed in conjunction with the traditional Willowstick Method to better characterize seepage flow paths and patterns trough, beneath, or around a dam in three dimensions. When both methodologies, which use entirely different scientific principles, identify the same anomalous feature, a higher degree of confidence is gained in the results of the investigation. Willowstick has effectively utilized the SAR method on many successful dam seepage investigations. The two geophysical techniques when used in parallel have yielded complimentary results, with both methods providing beneficial information about seepage locations. This paper will detail seepage flow paths identified using both Willowstick and SAR methods for two case study tailings dams in Canada and the United States.

Feb 1, 2023

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

By T. C. Vogt

The past history of uranium production has been dominated by strip and shaft mining methods, but recently in-situ leaching has emerged as a viable alternative for uranium recovery. (1-8) Mobil was the first company to start in-situ uranium leaching in New Mexico. Mobil's Crownpoint project areas are in Mdinley County and are part of the Grants Mineral Belt. The major uranium deposits in this area occur in the Westwater Canyon Member of the Jurassic Morrison Formation. (9-11) The ore depth at the Crownpoint project is about 2000 ft. In an earlier paper we discussed the uranium mineralogy of an areally broad sampling of Crown- point ore. (12) The organic carbonaceous material often associated with the coffinite ore was characterized in some detail. The organic material appeared to be a very mature, coaly-type kerogen derived from plant components. This result was consistent with other studies on such carbonaceous material. (13-15)

Jan 1, 1981

By V. Svalbonas

Everybody has an opinion what the quality of a grinding mill head casting should be, yet extremely few take the time, or get the opportunity, to compare their opinions against fitness-for-purpose data. The real question is not how flawless the casting should/could be, but rather how long will ?this? casting survive in operation. To validate an opinion on this topic one needs either extensive historical data, or comprehensive experimental data, or preferably, a combination of both. The same data can also be used to establish the conservativeness, or lack thereof, of analytical prediction methods.

Jan 1, 2009

When the 2008 Olympic Games begin in Beijing, China is September it will not only mark the end of the journey for the Olympic torch and the thou-sands of participating athletes, but the games will also mark the culmination of a massive amount of construction in the city. On display for the world to see will be 31 new and refurbished venues including the 91,000-seat National Stadium called the ?Bird?s Nest? and the aquatics center, called the Water Cube. What will not be featured as prominently on the television cameras broadcasting the games around the world will be the network of tunnels built beneath the city. But that infrastructure of rail lines will be of critical importance to the games. While preparing to host the world, China added a subway tunnel that will include four stops in the Olympic Park. The 4.4-km (2.7-mile) subway line that runs through the complex of stadiums, gymnasiums and parks began trial operations in June. Prior to the opening of that line, Beijing's No. 5 subway line, which runs through the heart of the city from north to south, opened in October. That 27.6-km (17-mile) line took nearly five years to build and includes 23

Jan 1, 2008

By Frank W. Luerssen

Introduction "Austerity" is perhaps an overly generous description of the past three years in the American steel industry. Steel plants operated at an average of only 57% of their capability in 1982-84. The dismal losses for last year are still being totaled. But during the two years before this period, American steelmakers recorded an aggregate net loss of a staggering $6.8 billion. Steelmakers responded by closing numerous marginal facilities. And production capability was cut by 13.6 Mt (15 million st). Capital expenditures still averaged $2 billion annually. But this was inadequate to maintain the existing base of steelmaking facilities. The general economy experienced a satisfactory recovery during this period. American steel, however, continued to suffer from a lagging recovery in the capital goods sector. This was due to record penetration of its domestic market by imports and from very weak realizing prices on the volume that was available. In addition to the direct influx of offshore steel products - which itself depressed prices - the industry also became painfully aware of the growing importance of "indirect" imports. These came in the form of steel-containing producer and consumer durables. Industrial equipment and autos fabricated from foreign steel accounted for the equivalent of 6 Mt (6.5 million st) of lost market opportunity for domestic steel-makers last year. That is over and above the 23.5 Mt (26 million st) of direct steel imports. Given these factors, Inland Steel was not spared from the threeyear downpour of red ink. Despite its record of continuing modernization in steel, our single-plant location in the world's best steel-consuming market, and the high proportion of consumer durables related products, such as cold rolled and coated sheet in our mix, Inland suffered aggregate losses of $277 million during the 1982-84 period. Strategic Planning The foregoing establishes a perspective - a base from which we have restructured our view of the steel industry, and of our own role within that picture. Until possibly two years ago, this present weakness in steel demand was viewed around the world as an aberration, eventually to pass. By contrast, it is now recognized that austere times are the normal steel environment. The topic here is management of resources. This implies an emphasis on strategic planning. It is worthwhile to examine some of the more critical assumptions that were driving strategies among a number of steel companies just before the 1980s. Those projected characteristics of the future steel environment were arrived at through painstaking analysis. They were carefully and heavily quantified and were generally shared by outside observers and our peers within the steel industry. • First, the assumption was made that domestic steel demand would continue to grow at an average rate of 2% per year. • Second, it was assumed that this growth in the American market would continue to be filled predominantly by US mills. It was believed that increases in steel and steel-related demand overseas would absorb much of the ominously growing capacity of third

Jan 6, 1985

By Paul D. Tomlingson

During the next several months, SME’s E-Newsletter will feature 15 articles on maintenance management. The articles may be read online or downloaded and distributed within your organization. They will address maintenance management topics, offer guidelines to mining managers and provide techniques that the maintenance manager can use. The articles will stress equipment management, a strategy that the mining industry has accepted as a modern replacement for outdated maintenance practices. Equipment management is the mutually supportive interaction of all mine departments as they establish equipment needs, procure equipment, test, commission, operate, maintain, modify and eventually replace equipment. The successful application of equipment management principles can quickly and reliably produce cost reduction and performance improvement results while providing a dependable way of sustaining them. Equipment management embraces modern management techniques. These include reliability-centered maintenance, life-cycle costing, capital performance, the effective use of information and productive organizational models.

Jan 1, 2003

By Leping Liu, Sachin Urade, Li-Ting Chen, Pengbo Chu

This study aims to provide industrial perspectives on the current U.S. metal mining engineering education and areas for improvement. An online survey was designed to seek opinions from the U.S. mining industry. Findings indicated a shortage of qualified graduates from the current U.S. metal mining engineering education system. The qualifications that need to be improved include engineering sciences underlying mining methods, mining design experience, mining feasibility study, the connection between theory and practice, and understanding of the overall mining operation. The survey also identified future desired qualifications, such as the ability to acquire and apply new knowledge as needed and sufficient field experience. Respondents recommended enhancing collaborations between industry and academia.

Oct 1, 2023