Search Documents

By T. T. Chen

Gold in the Twin Creeks ore is primarily associated with arsenian pyrite. During pressure oxidation, the sulphides are solubilized, but part of the dissolved iron reprecipitates as jarosite and as an iron sulphate-arsenate-phosphate phase. The pressure oxidation products are subjected to cyanide leaching. The cyanide leach residues consist of quartz, gypsum, bassanite, anhydrite, small amounts of jarosite, an iron-sulphate-arsenate-phosphate phase, as well as trace amounts of orthoclase, rutile, pyrite, hematite and monazite; all these particles are dispersed in a fine grained matrix of illite-muscovite. The autoclave leach residues contain a small amount of carbonaceous matter. Many gold grains are detected on the surfaces of the carbon particles, and these gold particles are not leached during cyanidation. The gold particles are typically 0.1-0.2/Lm in size and commonly are embedded in the carbon surface or are coated with a K-AI-Si-S-O phase on the surface of the carbon. The gold grains are consistently associated with elevated CI contents (50-300 ppm Cl). The poor gold cyanide leach recoveries, which initially occurred in the Twin Creek developmental circuit under certain operating conditions, are attributed to the presence of chloride in the feed. This results in the formation of soluble gold chlorocomplexes in the autolcave and the subsequent sequestering of the gold on the surfaces of the carbon particles.

Jan 1, 2000

By Yongqi Sun, Zuotai Zhang

Hot slags, at the temperatures of 1450-1650 oC, carry a substantial amount of high quality thermal energy, which represents the largest undeveloped energy source in the steel industry. However, the waste heat recovery rate in China is less than 2%; thus there is a great potential of waste heat recovery. In this study, we investigated a chemical method to extract the waste heat from high temperature blast furnace slags, i.e., sludge gasification. Sewage sludge, another substantial waste produced in the municipal system, need to be timely disposed, the organics of which could be gasified using the waste heat in the slags for the purpose of syngas production. Both the kinetics and thermodynamics of the sludge gasification process were clarified here. Most importantly, an integrated system composed of multiple systems such as the steel industry, the cement industry, the municipal system and the chemical engineering industry, was analyzed in this study.

Jan 1, 2016

By Hideya Sato

Refractory wear caused by melts is one of the major determining factors for the interval of shut-down repair of the metallurgical furnaces in general. Calcium ferrite slag employed by M it subishi Continuous Copper Converter, shows hi& fluidity and corrosive characteristics against most of the refractories. In order to improve the corrosion resistance of the refractories, the mechanism of MgO-based refractory wear by the calcium ferrite slag was intensively studied. The dissolution behavior of the refractory into the molten slag and the penetration of the molten slag into the refractory were observed by crucible tests and newly developed oscillating furnace tests. It was found that the wear of MgO-based refractories by the calcium ferrite slag is mainly dominated by the internal structural failure caused by the penetration of CaO-Cu20 rich slag which is formed as a result of the preferential absorption of FeO, from original slag by the spinel of the refractory.

Jan 1, 1999

By Duclerc Fernandes Parra, Luis Filipe Carvalho Pedroso Lima, Harumi Otaguro, Washington Luiz Oliani, Hélio Fernando Rodrigues Ferreto, Ademar Benevolo Lugao

The activation of three polyethylenes, the low density, the high density and the linear low density polyethylene, was determined by means of dynamic mechanical analysis (DMA). Storage modulus and tan δ spectra were obtained as a function of the temperature from −60 to 50 °C with a heating rate of 2° min−1 at frequencies of 1, 2 and 5 Hz and measurement strain amplitude of 10−5. In the tan δ spectra, a small peak in the β region of the three polyethylenes was found and substantiated by subtracting the growing exponential background. This procedure was based on a model that associates the dislocation motion on metals under cyclic stress to vibrating strings and considering the same for the polymeric chains. For the determination of the activation energy we have utilized the frequency versus the reciprocal of the absolute temperature peak of the tan δ. The values obtained for the three polyethylenes, the low density, the high density and the linear low density were, 362 ± 12, 266 ± 9 and 197 ± 6 kJ mol−1, respectively, which were compared with those presented in the literature.

Mar 1, 2017

By Congcong Yang, Jian Pan, Deqing Zhu, Yang Zhong

A study of pelletization of one imported chromite concentrate with coarse site, poor ballability and refractory roasting performance was conducted in small scale tests, and high pressure grinding rollers (HPGR) was used to improve the pelletization. The mechanism of HPGR was revealed by means of SEM images and optical microscopy. Compared with the ball milling pretreatment, HPGR pretreatment can not only enhance the ballability of pellet feed but also drop the roasting temperature. Fired pellets, containing proper chemical compositions with high compressive strength of 2917N/pellet and good metallurgical performances, have been manufactured. The mechanism of HPGR reveals that chromite particle surface turns to more irregular after HPGR treatment and more new surface being formed because of more cracks, sharp corners and edges appearing, resulting in higher surface chemical activity, all of which improve the ballability of the chromite concentrate and contribute to the consolidation of fired pellets.

Jan 1, 2015

By E. N. Mounsey

Ausmelt Technology was selected by Bindura Nickel Corporation (BNC) as the basis for a new copper circuit to process nickel plant copper leach residue to blister, anode and finally cathode copper and recover PGM values at the Bindura Smelter Refinery (BSR). The process selected, based on Ausmelt Technology to smelt and convert the residue to matte and blister copper and produce a discard slag, is novel incorporating smelting, converting and slag reduction process steps in a single Ausmelt vessel. The process demands a high quality blister copper product with low levels of arsenic and nickel. This paper reviews the project and the initial operational results to the end of 1997 of the Ausmelt Top Submerged Lancing (TSL) smelter and discusses the implications for the wider TSL converter market.

Jan 1, 1998

By Lu Lin, Yan-ping Bao, Min Wang

In order to forecast the cost of dephosphorization during BOF process, and achieve economical dephosphorization of BOF. The mathematical model of dephosphorization cost for BOF process was established. The model calculations show that, when the silicon content and phosphorus content are increased in hot metal, and the final phosphorus content of BOF is decreased, the dephosphorization cost will be increased. The silicon content of hot metal is increased of 0.1% in the plant, the dephosphorization cost is added by 9 RMB/ton steel. The De-P cost of mode A is much higher than the other two modes for three typical production modes of single slag melting process, when the phosphorus content of hot metal is higher than 0.14%, an increase in the phosphorus content by 0.01%, the De-P cost of mode A is added by about 7 RMB/ton steel. Meanwhile, when the phosphorus content of hot metal is lower than 0.165%, the De-P cost of mode C is higher than mode B’s. For BOF single slag melting process, the dephosphorization cost calculated by model is between ± 2%, proving that the model is reliable for the prediction of dephosphorization cost.

Jan 1, 2015

By Nathaniel R. Quick

"Nd: YAG, KrF excimer, and Cu-vapor lasers are used in air to synthesize conductors and semiconductors as a second phase in silicon carbide and aluminum nitride. Conductor resistivities as low as 104 O-cm are formed in these substrates; the resistivities for the untreated substrates range from 10 11to 1014 O-cm. The silicon carbide conversion is relatively independent of wavelength while the aluminum nitride conversion shows a dependence on wavelength over the range 248 nm to 1064 nm. Silicon carbide conductors, evaluated over the range 15 K to greater than 300 K, exhibit metal like conductivity; resistivity increases with temperature. Silicon, carbon, and oxygen are identified as the principal chemical species associated with the conductor in SiC substrates while aluminum, nitrogen, and oxygen are identified as the principal chemical species associated with the conductor in aluminum nitride substrates. The silicon carbide system, which has the less complex phase diagram, is evaluated in more depth to explain the synthesis mechanism. Oxygen was principally on the surface and increasing SiC conductivity is associated with decreasing spacing between 5 µm, or less, diameter carbon globules. This technology is proposed as a replacement for metallization in electronic packages, sensors and devices. INTRODUCTIONCeramics are commonly used for multichip module, hybrid and multilayer electronic packaging; semiconductor device and sensor applications because of the insulating, conducting, semiconducting, or superconducting properties that these materials possess (1,2) The majority of ceramics, however, have not been known to exhibit conductive or semi conductive properties when exposed to rapid thermal heat processing. A ceramic and process which through selective conversion can combine two or more of these electrical properties to eliminate the need for metallization is of interest to both the commercial and military sectors."

Jan 1, 1994

By Peter K. Liaw, Charlie R. Brooks, David C. Joy, Wei Zhao

In this paper, effects of oxidation, porosity and fiber-fabric stacking sequence on flexural strength of a continuous silicon carbide fiber (SiCr) fabric-reinforced SiC ceramic-matrix composite (CFCC) were studied. The failure mechanisms were correlated with flexural strengths of CFCC samples, both before and after oxidation. Microstructures and fractography were investigated using scanning electron microscopy (SEM). The chemical change after oxidation, such as Si, C, and 0, and their distributions, were detected by the SEM energy-dispersive X-ray spectroscopy (EDXS) line-scan chemical analysis technique. These effects on the strength of the CFCC can be attributed to following reasons: (i) The decrease in the flexural strength after oxidation is mainly due to degradation of the strength of Nicalon fibers and the damage of fiber/matrix interface both caused by high-temperature chemical reactions, (ii) Porosity is not too important in affecting the strength of the CFCC, when the bonding of the forced flow chemical vapor infiltration (FCVI)-SiC matrix is stronger than that of the fiber/matrix interface. However, a higher porosity content will be harmful, because higher porosity will both decrease the effective elastic modulus of the FCVI-SiC and make pore-linkage easier to occur, which is more likely to cause premature failure, (iii) The variation in the lamina stacking sequence of the CFCC changes the elastic stress distributions along the thickness direction of specimens, the magnitude of ceramic matrix-cracking stress, the effective elastic moduli of the laminate, and different crack initiation sites as well as different failure modes, and thus, leading to the scatter in the flexural strength of the CFCC.

Jan 1, 1998

By Shadia J. Ikhmayies

In this work the equilibrium temperature-composition phase diagrams of the Si-O2 system were calculated using Thermo-Calc software in the temperature range 500–3000 K. Constituents of stable phases were obtained, and the amounts of certain phases where investigated with the variations in the composition of oxygen and temperature. It is found that quartz with silicon represent a stable phase in the temperature range 500–1150 K, while tridymite with silicon represent a stable phase in the temperature range 1150–1700 K. A liquid phase is found besides tridymite in the temperature range 1700–1750 K, and a stable phase of cristobalite with liquid appears in the temperature range 1750–2000. The maximum amounts of quartz, tridymite, and cristobalite are found at oxygen mole percent of 67.7%.

Mar 1, 2017

By Steven M. Puricelli

Sulfuric acid plants associated with smelters, have historically been an overworked and often neglected pollution control device. They could do little more than manage the wide fluctuations in gas flow and SO2 strength from the smelter. With the introduction of flash smelting, the picture began to change, but the fluctuating batch converters continued to dictate acid plant design. More recently, the commercial use of continuous converting processes utilizing high levels of oxygen enrichment has dramatically upgraded the SO2 strength and stabilized the gas flow to the acid plant. The SO2 gas now issues continuously and at concentrations that allow for compact and, cost effective acid plants. Relieved of the burden of excessive dilution air, the heats of reaction can also be recovered as medium pressure steam and used to drive a generator, making the acid plant a net producer of power and a valuable asset to balance sheets. This concept was put into practice at the Kennecott Utah Copper Corporation smelter modernization project, located in Salt Lake City, Utah. The new acid plant, which was commissioned in June of 1995, is a sophisticated, low environmental impact, energy producing plant, worthy of review. This paper examines the key features of this acid plant, such as controlling its tail gas, by catalysis alone, to an environmentally friendly, 100 ppm of SO2, while feeding the acid plant converter with an efficient 14% SO2. The acid plant is also a prudent steward of energy resources, recovering 220,000 lb/hr of 140 psig steam from process heat which is used to generate a substantial 20 MW of gross power. Also discussed will be some of the ongoing issues, such as handling of selenium and fluorine in the gas cleaning sections, as well as a review of some. of the problems that were identified and resolved. Today's modem acid plants, by necessity, are becoming a producer of quality, valuable products, making the acid plant an asset and not a liability. Plants like Kennecott are already gaining wider acceptance and are expected to be the vision of the future.

Jan 1, 1998

By Animesh Jha, Catherine Davey

"Carbothermic reduction and nitridation reactions using synthetic kaolinite mineral were investigated for the formation of silicon based nitrogen ceramics. The temperature dependence of the reaction rate and its effect on phases formed are reported. The effect of the reactivity of carbon on the kinetics of formation of AIN and ShN4 is discussed. Using the standard Gibbs free energy values for the formation of nitrides and oxides of aluminium and silicon, a log po2 verses I/T diagram is constructed. The experimental data results are discussed and compared with the predicted phase equilibria. We also report the influence of sub-oxide gaseous species on the microstructure of the ceramic phases produced.IntroductionSynthetic kaolinite is a clay containing alumina, silica and water of crystallisation, and has a chemical formula 3(Al2O 3.2SiO2.2H2O). This mineral is relatively inexpensive and, is therefore an ideal candidate for use in the production of ceramic powder mixtures for example silicon nitride and aluminium nitride for composite material formation, When the mineral is heated, the water of crystallisation from the crystal lattice is lost via the 3(Al2O 3.2SiO2.2H2O) = 3(Al2O3.2SiO2) + 6H2O reaction. It has been shown [1·2j that on further heating to 1673K, the anhydrous kaolinite decomposes to a mixture of mulllte and silica, 3(Al2O3.2SiO2) = 3Al2O 3.2SiO2 + 4SiO2 which is consistent with the alumina-silica phase diagram, shown in figure 1.The binary alumina-silica phase diagram has a well-defined sub-eutectic immiscibility dome and this characteristic dernixing behaviour is reflected in the thermal decomposition of anhydrous kaolinite consequently the microstructural features resemble the spinodal decomposition process. It is well established that the spinodal decomposition process raises the nucleation frequency due to their low free energy barrier, (?G). The small magnitude of this barrier consequently promotes the evolution of a very fine microstructure. The process of spinodal decomposition is therefore expected to be influential during the reduction-nitridation of kaolinite minerals."

Jan 1, 1996

By W. Petruk

The behaviour of galena, chalcopyrite and tetrahedrite during floration of a fine-grained base metal ore from New Brunswick was investigated by image analysis study of the mill concentrates and tailings. The minerals were analyzed to determine the grades and recoveries as related to free and unliberated mineral grains and their size distributions. The results show that only 37 wt % of the galena was liberated but 88 wt % of the free galena was recovered, indicating good mill performance for the lead. The lead recovery was 65 wt %, with the main loss due to unliberated galena. Most of the unliberated galena lost to mill tailings is so fine-grained that galena liberation and Pb recovery would not improve significantly by re-grinding. Chalcopyrite liberation was 56 wt % but only 75 wt % of the free chalcopyrite was recovered. Copper recovery was 45 wt %, with the chalco-pyrite loss in the mill tailings being both as large free grains, and as small and large unliberated grains. It was calculated that copper recoveries could be improved about 8 to 10 wt % by changing the concentrator operations and by regrinding. Concentrator operations hive already been modified and copper recoveries have improved about 5 wt %. About 29 wt % of the silver was lost to tailings mainly as both free and unliberated, large and very small, Silver-bearing tetrahedrite grains. It was calculated that about 25 wt % of the silver in the tailings might be recovered by improved milling conditions and by regrinding.

Jan 1, 1981

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By Takamitsu Nakasuga, Haiping Sun, Kyushu University, Katsumi Mori

"The kinetic behavior of reduction of chromite ore by liquid iron containing carbon and silicon has been investigated under various experimental conditions to clarify the reduction mechanism. It was found that the reduction rate of chromium ore by liquid Fe-C alloy was very slow. In addition, when carbon and silicon coexisted in the iron melt, silicon was found to preferentially oxidized to form silica, which favored for the fonnation of liquid slag and the rate of reduction was considerably accelerated. The similar effect was obtained by the addition of some fluxes, such as SiO2, Na2B407, CaO-SiO2, which also promoted the formation of a liquid slag and thus the reduction rate in the early stage also increased.IntroductionThe reduction of Cr2O3 is a basic reaction for production of ferro-chromium from chromite ore and for chromium recovery from the slag fonned during the decarburization period of a stainless steel-making process. The reduction of chromite ore consumes much energy and its reaction rate is not so high. Thus, in order to increase the reduction efficiency, it is strongly desired to clarify its reduction mechanism from the practical and the theoretical points of view."

Jan 1, 2000

By R. J. Wesely

In recent years the trend in copper smelting has been to expand existing smelters to increase their throughput. New smelters under consideration are large, typically in excess of 200,000 tons per year of copper. Despite this trend to larger smelters there are a number of conditions where a much smaller smelter can be economically viable. This paper examines these conditions and outlines the process concepts for a small smelter treating from 20,000 to 100,000 tons per year of copper.

Jan 1, 2000

By Julien Favre, Akihiko Chiba, Damien Fabregue, Yuichiro Koizumi, Eric Maire

"The mechanical behavior of Co-20Cr-15W-10Ni alloy is studied by compression tests at high temperature. Microstructures after deformation are evaluated using SEM-EBSD. Significant grain refinement occurs by dynamic recrystallization for high temperature and low strain rate (T>1100°C, <0.1s-1), and at high strain rate (~10s-1). Dynamic recrystallization is discontinuous and occurs by grain boundaries nucleation, leading to a necklace structure. The nucleation mechanism is most likely to be bulging of grain boundaries. However, recrystallization occurs also by rotation of annealing twins which can bulge as well. The modeling of mechanical behavior gives a fair quantification of flow softening due to dynamic recrystallization, indicating the progress of dynamic recrystallization with deformation.IntroductionCobalt-chromium alloys are used in biomedical applications for the elaboration of implants due to their outstanding mechanical properties and their high resistance to corrosion. For stent application a large ductile behavior is required in addition to the high mechanical strength. Indeed stents have to undergo a deformation until e˜40% during their expansion [1]. Conventional Co-Cr-Mo (CCM) alloys exhibit limited ductility (maximal deformation about e˜30%) [2]. Co-Cr-W-Ni (L-605) alloy is a better candidate for stent elaboration since its fracture strain can exceed 40% (comparable to nickel superalloys (Figure 1), while it keeps high mechanical strength. In spite of the presence of nickel element in this alloy, biocompatibility is sufficient for vascular implants, therefore L-605 alloy is extensively used for heart valves and stent elaboration [3]."

Jan 1, 2012

By Kampe. S. L., Baker. Andrew H., Tony Zahrah

"Experimental heats of reaction for the formation of several Al3Ti + TiB2 intermetallic composite formulations have been determined utilizing bomb calorimetry. To overcome the kinetic constraints and achieve ignition in these formulations, a boron (B)/potassium nitrate (KNO3) initiation aid was incorporated within the blended reactant compact. The heat contribution from the initiation aid was regressed to provide estimates of the heat of reaction of the nominal formulations. Powder x-ray diffraction was utilized to identify the products of the reaction and discern any differences between the predicted equilibrium products of the formulation and the actual products.IntroductionReaction synthesis is a technique for the creation of ceramics, intermetallics, and in-situ composite materials [1]. Reaction synthesis is defined by its self, propagating mechanism, where the energy liberated from a localized reaction within a green powder compact is enough to carry the bulk reaction to completion. Achieving a self, propagating state can be achieved in variations of two primary methods of initiation: uniform volumetric heating and directional propagation [2].Uniform volumetric heating involves subjecting a green compact of the unreacted formulation to uniform heating in a furnace to encourage diffusion to initiate the reaction (Figure 1a) throughout the bulk material. Directional propagation utilizes a point heat source at one section of a green compact of unreacted formulation (Figure 1b). The localized exothermic reaction at one point in the compact then initiates the reaction in the section of the compact adjacent to it and fully propagates throughout the entire compact until completion. Initiation of the localized reaction is generally associated with the melting of the constituent with the lowest melting point, with instantaneous initiation of the reaction usually occurring close to that melting point [1]. This melting point can be high in some systems of interest, such as the titanium (Ti) and boron (B) system in equation 1:"

Jan 1, 2011

By D. M. Hausen

Multiple drill sections through many of the numerous breccia pipes in the American Eagle copper deposit at Copper Creek, Arizona, have been evaluated by means of alteration and geochemical data. Contoured plots indicate vertically plunging, concentric, cylindrical shells of alteration and mineralized rock that are similar in structure, geometry, magnitude and petrology to the San Manuel-Kalamazoo Deposit, located about 14 miles to the southwest. Both deposits are similar in dimension and consist of multiple, irregular, rod-shaped injections of porphyry into a granodiorite host. Analogous to the San Manuel-Kalamazoo Deposit, most of the porphyry plugs are oriented parallel to the cylindrical axis of the "ore shell". A continuously mineralized, elliptical shell, inferred from deep drilling, is capped by a flatter zone of copper mineralization. Above this flat zone, copper-bearing fluids were channeled upward along conduits that correspond with quartz-sericite "breccia pipes". At depth, zones of sericite and K-feldspar alteration products exhibit conformable relationships with the copper deposition. A "bullet-shaped" ore shell, with a nearly vertical axis, is proposed to explain the conformable zones of altered and mineralized rock. The "nose" or top of the "bullet" is 1800 to 2300 feet below the surface, and structurally controlled in part by steeply dipping Hi and ENE faults. If correct, this model suggests that the vertical ore shell may extend to great depth.

Jan 1, 1988

By Donna M. Noel

Bacterial strains have been cultivated from solids previously exposed to cyanide that will tolerate 300 ppm sodium cyanide under anaerobic conditions. In selected solid samples, these bacteria have been shown to reduce the level of cyanide from approximately 300 ppm to essentially zero in about 50 days under anaerobic conditions. Various media were investigated, and the nutrients providing maximal growth were ?established .. Degradation of cyanide in sterilized solids was determined for comparison with degradation obtained in bioactive solids. All experiments were conducted at ambient temperature and initial pH of approximately 10.5.

Jan 1, 1991