Search Documents

By Shubin Wang

Copper(II) and nickel(II) are often recovered from ammoniacal alkaline solutions by solvent extraction using hydroxyoxime extractants: both copper(II) and nickel(II) are extracted from ammoniacal alkaline solutions and, from the loaded organic phase, nickel(II) is selectively stripped with a dilute acid followed by copper(II) stripping with an acid of higher concentration. Since a small portion of ammonia is co-extracted with copper and nickel, the extracted ammonia should be scrubbed using a dilute acid before metal stripping. In the present study, a mechanistic model has been developed in order to support design and control of this process. The equilibrium distribution ratios of copper(II), nickel(II), and ammonia at 298 K using LIX® 84-I (active component, 2-hydroxy-5-nonylacetophenone oxime) as the extractant are successfully correlated by considering the relevant equilibria. Based on these results, quantitative prediction of equilibrium distribution ratios in the process has been made possible, and suitable conditions for the efficient separation of copper(II) and nickel(II) are discussed.

By Alexandre Bonan

This paper reports the results of a kinetic study on the oxidation of free cyanide and Cu-cyanide complex ions with HO,. The variables and respective ranges studied were the following: [CN] total =10 - 500 mg/l; pH=10-11; (H2O2/CN) mole ratio = 1- 3; (Cu/CN) mole ratio = 0.10 - 0.25. The results were interpreted by a semi-empirical model that incorporates the useful oxidation reactions and the parallel alkaline decomposition of H2O2

Jan 1, 1994

By Qixing Yang, Björn Haase, Fredrik Engström, Anita Wedholm

"MiMeR, the Minerals and Metals Recycling Research Centre at Luleå University of Technology, Sweden, started industry-related research work to stabilize an EAF slag from Höganäs AB with of CaO/SiO2 values near to 3.2. The intention was to determine the suitability of the EAF slag as construction material after stabilization. Some of the stabilizers effective for preventing disintegration of AOD slag were examined in laboratory tests for stabilization of the EAF slag. The EAF slag samples were mixed together with stabilizers for melting at 1600ºC and then cooling in a crucible system. With a laboratory granulation system, the liquid EAF slag was cooled rapidly using air. Samples from the tests were characterized by different techniques, including XRD and SEM. Some of the results from the work may be useful for preventing slag disintegration and, thus, enhancing utilization of the EAF slag as construction material, thereby saving valuable natural resources.IntroductionAt steel plants of some MiMeR member companies, steel grades with low carbon contents were produced in Electric Arc Furnaces (EAF). EAF slag was tapped out of the furnace to slag pots for transport to slag yards, where the slag was poured on the ground. Very often, the EAF slag disintegrated during cooling on the ground. Fines from the slag disintegration were often difficult to handle and use as material for road construction [1, 2]. The EAF slag disintegration was rather similar to the disintegration occurring in the slag tapped from some AOD (Argon Oxygen Decarburization) converter heats.Literature studies show that formation of dicalcium silicate (C2S) is the main reason for the disintegration or dusting of AOD slag from production of stainless steel [1-4]. The C2S can form while the content ratio of CaO to SiO2 of the slag, CaO/SiO2, exceeds 1.4 [1]. Values of CaO/SiO2 for the AOD slag are often near to 2.0, making the C2S a predominant slag component. The ß phase of C2S, ß-C2S, transforms into its low temperature ? form in the temperature range of 400-500°C, inducing a volume expansion of nearly 12% [1-4]. The volume expansion disintegrates the AOD slag."

Jan 1, 2008

By Kezhuan Gu

Data on the kinetics and thermodynamics of dephosphorization are analyzed in terms of the dynamic partition ratio, determined by a combination of slag thermodynamic properties and the balance of oxygen supply and consumption. A recently developed phosphate capacity correlation is combined with data on kinetics to quantify the most significant parameters in controlling the interfacial oxygen potential. The role of slag composition, entrained gas fraction and temperature are discussed in addition to metal carbon and sulfur content. It is demonstrated that the mass transport of oxygen in the slag is enhanced by factors increasing conductivity and inhibited by entrained gas. The mass transfer of phosphorus in the metal is described considering surface renewal induced by CO bubbles.

By R. K. Mehta

Microorganisms have been increasingly used in applications such as-metal solubillzation, precipitation and recently being used as flocculants. Optimal control and on-line monitoring of these processes occurring in microbial reactors are of extensive interest but often difficult because of the unavailability of a mechanistic model of the process and on-line direct sensors. In this paper a dynamic populatlon balance model of microbial desulfurization will be presented. The influence of certain physical and biological parameters on the leaching rate will be illustrated via computer simulations and an extended continuous-discrete Kalman filter will be Implemented for estimation of unknown states.

Jan 1, 1991

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By Terry Mandziak

Typical leach mine operations recover gold values through the application of a dilute cyanide solution onto ore within an engineered facility. Key to the success of mining operations is the, containment and management of the cyanide solutions within the facility. Properly engineered' facilities will have containment systems that are both protective of the environment while enhancing solution recovery. This paper not only discusses general containment standards, but identifies state-of-the-art containment and monitoring practices;

Jan 1, 1998

"The pyrometallurgical method of recycling car batteries suffers from a potential for air pollution violations, which prompts the desire for a viable hydrometallurgicaJ alternative. Several Processes have been proposed, including leach-electrowinning routes using HBF4 and/or HzSiF6 based electrolytes, along with anodes of PbO2 on inert substrates.A study has been carried out to evaluate the proposed systems, with the intention of demonstrating a six month life of an electrolyte-anode combination. The work, which focused on the use of HzSiF6, has indicated that there was no acceptable anode, and has lead to the development of a technique to produce smooth, glassy, adherent coatings on graphite, and to the development of an anode composed of a series of copper cored graphite rods.The paper will present results on leaching and electrowinning experiments, as well as the description of a flowsheet for a pilot plant that will be used to produce one tone per day of refined lead from spent battery paste."

Jan 1, 1997

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By Mahmood Alemrajabi

When LKAB processes their iron ores in northern Sweden, they generate apatite as a by-product. The apatite has been recovered by flotation and the concentrate contains about 0.4 wt% rare earth elements (REE). Both phosphate rock and REE are listed as critical raw materials for the European union. In the present study, the recovery of REE within the nitrophosphate process of fertilizer production has been studied. In the first stage, the REE are precipitated and isolated as a phosphate concentrate. For further purification and individual separation of REE by solvent extraction, removal of phosphorous from the concentrate to enhance the dissolution of REE in mild acidic solutions is essential. In this study, thermal treatment of the concentrate with sodium hydroxide at elevated temperatures followed by water leaching has been studied in order to separate the phosphorous and thereby facilitate dissolution of the REE. The results show that 95% of total phosphorous initially present in the REE phosphate concentrate is removed after thermal treatment with NaOH 1:1 mass ratio, at 400 °C.

By D. R. Flynn

The recovery of nickel and cobalt from electromachining sludges in the form of relatively high-purity marketable products has been investigated. The investigation has shown that a series of metallurgical unit operations can be performed to recover nickel and cobalt from electromachining sludges in the form of al kal i nickel ic hydroxide and cobalt sulfate/cobal t metal, respectively. The recovery unit operations for nickel include high pH cyanide complexation, followed by oxidation and precipitation of alkali nickel hydroxide. The resultant filtrate can be treated for cobalt recovery by neutralization and acid baking to produce cobalt sulfate. The cobalt sulfate can then be treated for cobalt recovery by electrowinning. Results from laboratory bench scale test work are discussed in terms of appropriate operating conditions.

Jan 1, 1991

By M. H. Lin, S. Kou

"Czochralski pulling has been a very widely used process for growing single crystals for electronic and optical applications. Dopant segregation can significantly degrade the quality and yield of single crystals. We have used the floating-crucible technique for segregation control in Czochralski pulling, our floating crucibles being unique in that the melt passageway is very long. As such, dopant back diffusion is suppressed, even when the cross-section of the melt passageway has to be relatively large to help the melt go through or when the pulling rate is very low. Single crystals of model materials K-doped NaN03 and Pb-doped Sn have been grown with very uniform dopant concentrations. IntroductionSingle crystals of electronic and optical materials are often doped with a small amount of impurities to develop required physical properties, e.g., P and B in Si for n-type and p-type semiconductors, respectively, and Nd in YAG lasers. Dopant segregation can result in nonuniform physical properties, thus degrading the quality and yield of the resultant crystals.Figure 1 is an illustration of the conventional Czochralski process for crystal growth. Several techniques have been developed to control dopant segregation in Czochralski pulling, including the push-pull technique (1,2), the drop-pull technique (3-7) and the floating-crucible technique (8-13). The first two techniques require precise sensing devices and feedback control systems to keep the feeding rate equal to the pulling rate. The last technique is simple since the feeding rate is automatically equal to the pulling rate."

Jan 1, 1994

By Lifeng Zhang, Zineb Benouahmane, Yaqiong Li

Experimental oxidation tests at high temperature (1000-1200 °C) on SiC samples have been respectively performed under wet and dry air atmosphere for different holding times. The thickness of thermally grown oxide was experimentally measured by DEKTAK Stylus Profilometry. The results showed that the oxidation rate was increased with temperature and holding time, corresponding to a passive oxidation regime which led to the formation of SiO2 layer. The sessile drop method was employed in order to measure the contact angles between Si and SiC at high temperature. Contact angle can be varied from 39.6° to 75.6° by controlling the atmosphere. The deoxidation of the oxide layer and infiltration of liquid silicon caused a decrease in the contact angle.

Jan 1, 2016

By Wayne Bell, Xiaodi Huang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng

"The equations for determining microwave field attenuation length and half-power depth in magnetic materials were derived from Maxwell’s equations. The microwave field attenuation length and the half-power depth for a magnetite concentrate were calculated and the temperature dependence of them was determined. It is demonstrated the microwave field attenuation length and the half-power depth highly depend on temperature and decrease with increasing temperature up to 900 °C. The variations of field attenuation length and the half-power depth with temperature indicate the microwave power attenuates much faster than the field strength in materials. The evaluations of field attenuation length and microwave half-power depth can be used to characterize the microwave dissipation behaviors in the sample and optimize the dimensions of the material in microwave heating.IntroductionMicrowave has been applied in materials processing for its distinguished advantages including rapid heat transfer, volumetric and selective heating [1,2]. However, most research work involving microwave heating are confined to non-magnetic materials (e.g. ceramics), with limited attention paid to the heating of mixed property materials (e.g. magnetite and other ferrites) under microwave irradiation [3-5]. Since many magnetic materials exhibit good and even better microwave absorption capability than non-magnetic counterparts, it is quite necessary and deserved to take advantage of this property and then improve the heating efficiency. To achieve this aim, further understanding on the microwave heating mechanism, especially the microwave propagation/dissipation behaviors in magnetic materials is required.The dissipation behavior of microwave in materials has been identified as one of the key factors that affect the efficiency of heating under microwave irradiation and this behavior can be characterized by several parameters. Apart from traditional penetration depth (TEM power penetration depth, Dp = 1/(2*a), where a is the TEM field attenuation factor), two other parameters, field attenuation length (Df) and half-power depth (Dh), are also applied to indicate the microwave dissipation in materials [6].The accurate determination of such parameters can help in optimizing the dimensions of the load in a microwave furnace, producing more uniform heating under microwave irradiation and avoiding thermal runaway."

Jan 1, 2011

By T. Ikeda, M. Maeda, K. Mita

Galvanized steel sheet is the major product for the automobile industry. Therefore, automotive recycling results in zinc-containing scrap that should be remelted in EAFs. Naturally, the EAF dust is a very important source of zinc for zinc recycling processes. The thermodynamic properties of the Fe-Zn intermetallic compounds formed on the surface of galvanized steel sheet should be clarified to make clear the evaporation mechanism of zinc; however, there are few reports on these compounds because of difficulties in their synthesis. There are various intermetallic compounds in the Fe-Zn system. We synthesized them at about 673K. A specimen was examined chemically and X-ray diffraction was applied to ensure the formation of intermetallic compounds. Material containing two phases was placed in a Knudsen type effusion cell and the mass spectrum studied to evaluate the vapor pressure of zinc. The thermodynamic property of intermetallics was then evaluated through measured intensity.

Jan 1, 2000

By Takayoshi Fujii, Mitsumasa Hoshi, Chikashi Suenaga, Yoshiaki Suzuki

"In a bid to renovate its Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, Nippon Mining & Metals undertook major - restructuring efforts since 1993.One of its themes was the shift from a two-flash furnaces operation to a single-flash furnace operation. The shift was successfully completed in 1996 while maintaining the production at the same level (330,000 metric tons per year of copper) by adopting such measures as improvements in pneumatic concentrate dryers, the concentrate feeding system, concentrate burners, the furnace cooling system, and a new cryogenic oxygen plant was constructed.With a view to realizing high matte grade operation (at 65%Cu) and increasing the concentrate feeding rate, further steps were taken the capacity of waste heat boiler was expanded and technical improvements were added, including optimization of the smelting reaction in the furnace shaft. As a result, the smelting capacity, as of the year 2000, has increased to 450,000 metric tons per year of copper.IntroductionThe feed rate to the flash furnace was doubled to 140 t/h from 70 t/h in 1996. Teething problems, as a result of the renovation, were almost solved by the end of 1996, and the operation of the single furnace operation has become stable.The main theme was the shift from a two-flash furnaces operation to a single-furnace operation to maintain the production capacity at the same level, namely 330,000 metric tons of copper per year. Then, in a bid to further renovate the Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, further enhancement of the flash furnace's productivity was planned.The purpose of this plan was to raise the copper production capacity to 450,000 mtpy building on the potentialities of existing plants and without installing new equipment."

Jan 1, 2000

By P. Cowx

The carbothermic reduction of zinc oxide rich Electric Arc Furnace baghouse dust in the Tetronics transferred arc plasma furnace to produce a non-toxic slag and a metallic zinc product is described. In particular, the operation of the zinc splash condenser coupled to the plasma furnace is examined and the effect of process variables on zinc recovery is discussed.

Jan 1, 1990

By Keizo Uematsu, Satoshi Tanaka, Zenji Kato, Nozomu Uchida

"A novel technique is developed and applied to evaluate the binder segregated at the· surface of granule. Compressive strength of each granule was measured directly with a micro-compressive instrument. The relation between compressive characteristics and the amount of binder was discussed quantitatively.IntroductionCharacterization of granules is essential in the production of ceramics, since they govern the structure of green compact and thus the structures and properties of ceramics. However, there is no research to clarify the relation between the strength of granules and structure of granules, especially of binder segregation at granule surface. We develop a novel technique to determine the binder concentration in the granules by the iodine method. In this study, we measure yield strength of granules directly and discuss the relevance between compressive characteristics and the concentration of binder.ExperimentalGranules were prepared by spray-drying of aqueous slurry of commercial alumina (AL160-SG1. Showa Denko, Tokyo, Japan) and PVA (PVA 105 Kurare, Japan). PVA. concentration in granules was 1.1, 1.5 and 2.3 wt%. The inlet and outer air temperatures were 200 and 95 °C , respectively. Iodine-potassium iodide solution was prepared by dissolving iodine (0.15mol) and potassium iodide (0.15mol) in diluted water (50ml). A saturated boric acid solution was prepared by mixing boric acid powder with a diluted water."

Jan 1, 2000

By G. Belardi

A study has been conducted to assess a new wet beneficiation treatment for the recovery of the sulphuric-acid-soluble titanium oxide contained in the waste from an Italian TiO2-pigment facility. The waste is produced during treatment of a Ti-enriched slag and contains as main components TiO2 (54%, of which 42% acid-soluble and 12% insoluble), SiO2 (27%) and A1203 (6%). Eighty percent of the material is finer than 50pm. The first step was to ascertain the possibilities offered by size classification, wet gravity separation, froth flotation and wet high-intensity magnetic separation to improve the grade and recovery of Ti02 and reduce the SiO2 content. The next step was to optimize the operating conditions of the various separations and assemble them into a complete flow- sheet. Beneficiation ensures potentially 70% recovery of the TiO2 with a concentrate grade of 80%.

Jan 1, 1998

By Jack S. McPartland

The recent developments on the concentration and recovery of gold from leached gold thiosulfate solutions by solvent extraction, reduction-precipitation, and electrochemical deposition are reviewed in this paper. Alkyl phosphorus esters have been found to extract gold only in alkaline thiosulfate solutions, The recovery of gold increases with thiosulfate concentration in the aqueous phase and with alkyl phosphorus esters concentration in the organic phase with aliphatic hydrocarbon diluents. The addition of ammonia improves the extraction. The extraction of gold with amines in either aliphatic or aromatic diluent decreased in the following order: primary>secondary>tertiary amines. Increase in the extractant concentration at high pH increased the extraction of gold. At pH < 9, the primary amine, RR&apos;CHNH2 with 1&apos;9-23 carbon atoms is the main extractant with TBP as the synergistic reagent and at pH >9, the primary amine shows a synergistic effect on the extraction of gold&apos; with TBP. TheAu(I) ions in thiosulfate solution are reduced by sodium borohydride (SBH) to metallic gold, with particles in the sub micron range, At an SBH/ Au ratio of 6.25, pH = 6, and at room temperature, the I e ppm Au(I) in a solution of ] 0 gil thiosulfate was completely reduced to metallic gold in about 60 minutes.

Jan 1, 1999