Search Documents

By Koichi Kobayashi

Performance-based approach to design of structures including foundations was adopted after enforcement of the revised Building Standard Law in Japan in 2000. The use of piled-raft foundation is favorable for medium-rise buildings in soft ground because of its good performance. In the design of the piled-raft foundation (Architectural Institute of JAPAN2002), vertical load is usually carried by the raft foundation, while the pile is primarily meant to control settlement of the structure. Shaft friction is expected to be larger in a nodular pile(Karkee, et.al., 1998) since it has larger surface area than a straight pile, and such piles are frequently used in piled-raft foundations. Since few structures with piled-raft foundation exist currently, the settlement characteristics of piled-raft foundation have not been fully clarified. To design piled-raft foundations with better confidence, the mechanism of vertical bearing capacity and the spatial distribution of settlement should be clarified, for which the actual behavior of the building-foundation system needs to be evaluated. This paper presents observations of settlement of a building with a piled-raft foundation at a soft ground site. The building is a steel structure covering an area an 766 m2, and consists of two-storey office block and one-storey warehouse block. The filled ground of about 5-m thickness at the ground surface is underlain by approximately 4-m thick alluvial sand layer below which lies about a 17-m thick alluvial clay layer with SPT N-value less than 2. The piles used in the piled-raft foundation are 12-m long nodular piles with nodal diameter of 500 mm (pile shaft diameter is 400 mm). The bored pre-cast piling method (Karkee, et.al., 1998) was used to install the piles. To evaluate the foundation settlement, the method of analysis of three-dimensional frame system, utilized widely in Japan, was adopted in combination with the foundation system. Basic assumptions were: (i) total ground settlement is evaluated as the sum of immediate settlement and consolidation settlement, (ii) immediate settlement is evaluated from the Mindlin?s solution in which strain dependency of shear modulus of soil is considered, (iii) settlement in clayey layers is evaluated by the one-dimensional consolidation theory, and (iv) shear spring between soil and pile shaft is represented by a hyperbolic function. The applicability of the method of analysis was verified by comparison with results of field monitoring of building settlement.

Jan 1, 2006

By Hamid Maleki

A geotechnical monitoring program has been implemented at Energy West Mining Company for enhancing site-specific evaluation of longwall stress conditions. This program consists of underground measurements at five locations in two neighboring mining districts located in the Hiawatha and Blind Canyon Coal Seams under moderate to deep cover. Within the last five years, additional measurements, including data on recorded seismic events and face conditions, have been incorporated into the data collection program together with detailed geologic mapping of longwall gateroads. In conjunction with the measurement program, the authors have completed detailed boundary-element stress analyses of the mine plans. Models have been calibrated using the data from in-mine instrumentations and then routinely used for evaluation of mine plans at depths approaching 2,600-ft. The work has improved our understanding of load transfer, seismicity and yield pillar performance. It has identified areas of potential increased stress levels at certain longwall face positions and provided guidance to measures that could be considered to mitigate the potential for these increased stress levels.

Jan 1, 2009

By Michel Brissette

"To recover more valuable ore and considering the complexity of minerals, the needs to grind finer is increasing. To reach the desired fine grinding targets, using the existing grinding media size, the energy consumption is increasing exponentially. As already proved at this conference, small grinding media represents the best potential to improve grinding efficiency. How do the small grinding media perform in industrial grinding mills?The use of small grinding media in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, smaller grinding media versus 25 mm media generate a power saving from 10% to 44%. In vertical stirred mills, the power saving increases from 20% to 60%. More potential savings have been identified.For the same operating conditions, how a vertical stirred mill is performing compared to ball milling? In regrind application, a vertical stirred mill with small media (5-12 mm Millpebs) will require at least 62% less energy than a ball mill charged with 25 mm grinding media.INTRODUCTIONIn some mining applications, fine grinding is needed to liberate further the valuable ore. The purpose of regrind mills is to achieve the last stage of grinding before final flotation stage: the cleaners. In part because of high prices of small grinding media as well as availability, the most widely used size of grinding media is 25 mm.When calculating the recommended ball top size from Bond’s formula (Bond, 1961), the size for regrind applications is much lower than 25 mm. Today, the barrier for small grinding media is broken. They are best suited in regrind application. The size of grinding media is one of the most important variables affecting the mill efficiency (McIvor, R., 1997; Nesset, J.E., Radziszewski, P., Hardie, C. & Leroux, D.P., 2006).Conventional ball milling was discarded for fine grinding because of its very poor energy efficiency (Zheng, J., Harris, C.C. & Somasundaran, P., 1994; Yan, D.S., Freeman, M. & Dunne, R., 1995). Therefore, new technologies as stirred mills were developed to grind finer more effectively. Three fundamental questions should be asked. What is the best fine grinding technology? What should be the best media size to use? Is it possible to grind finer by using less energy with the existing regrind equipment?"

Jan 1, 2009

By Leonardo Martins da Silva

O minério de ferro quando encontrado contendo teores do elemento fósforo acima de 0,05% é considerado rejeito dada sua inutilização para o processamento de fabricação do aço. Tal fato ocorre devido a elevação da dureza do aço tornando-o quebradiço e com fratura. Sendo assim o presente trabalho tem como objetivo a avaliação do efeito do processo de lixiviação ácida como finalidade de redução do teor de fósforo no minério de ferro. Através da utilização do software Termocalc® foi possível analisar as diferentes estruturas formadas em diferentes teores do elemento fósforo. Através da técnica de microscopia eletrônica de varredura (MEV) foi possível analisar a estrutura do minério de ferro após seu tratamento com a energia de micro-ondas. Por meio da técnica de planejamento estatístico fatorial com pontos centrais e axiais foi possível determinar as condições ótimas de remoção de fósforo através da técnica de lixiviação ácida.

Aug 1, 2018

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

The Century zinc-lead-silver deposit has a geological resource of 118 million tonnes averaging 10.2% zinc, 1.5% lead and 36 g/t silver. It lies approximately 250 krn NNW of Mt Isa in NW Queensland, Australia, and is hosted by middle Proterozoic age siltstones and shales of the Lawn Hill Formation. Within the orebody, most mineralisation occurs selectively within black shale units as fine grained sphalerite and galena lamellae with minor pyrite and siderite. The black shale units are separated by weakly mineralised sideritic siltstone horizons. The deposit is unmetamorphosed and only weakly deformed, displaying excellent lateral stratigraphic and grade continuity. The deposit is mostly overlain by younger Proterozoic sediments and later Cambrian age limestone cover and only a small proportion of the mineralisation crops out. Mineralisation has a subtle surface expression without a classic gossan profile, probably due to the low iron sulphide content of the ore. These factors contributed materially to the length of time between the first recognition of lead-zinc-silver mineralisation in the area by prospectors in the 1880s, to the discovery of the orebody by CRA Exploration Pty Ltd (CRAE) in April 1990.   Small scale prospecting and mining continued in the area from the date of the first mining lease in 1887. Post 1950, the deposit area was also included within nine separate regional exploration titles prior to CRAE's title acquisition in 1987. CRAE's original exploration strategy was partly pragmatically and partly conceptually inspired, but the eventual discovery only partly conformed to the original conceptual model. The deposit was found higher in the stratigraphy than the original target position, with unexpectedly low total sulphide content relative to other known deposits.   The discovery soil anomaly was located by the CRAE's first regional orientation traverse line in the area, but was not drill tested for three years. The discovery sequence at Century has strong elements of persistence, technical competence and some luck. It demonstrates that even in well explored terrains (by conventional standards) the exploration story can never be said to be over. The foreshadowed development of an economic resource at Century will hopefully inspire continued commitment to 'brownfields' exploration by mining companies, and demonstrate to external regulators the importance of genuine multiple land use strategies and the need for continued access to land for exploration and mining purposes.

Jan 1, 1995

By Charles Steed

The design of pillars in room and pillar operations is always a compromise between factor of safety and ore recovery. In actively mined and accessed areas the stability of pillars must be sufficient to support the roof, providing safe working conditions for men and equipment, while optimizing ore recovery. As a reserve is mined out, and if conditions are favourable, pillars are often removed to increase recovery. Considerations for pillar removal include value of the ore, the effect on immediate and overall mine stability and the safety of the mining operations as well as the consequence of disruption of overlying strata and surface infrastructure as the support of the pillars are removed. Many parameters influence pillar strength and the contribution of the pillar to ground support. These include seam height, seam depth, seam inclination, room span, quality of rock, time, etc.. Empirical, analytical and numerical modeling methods are commonly used to optimize pillar sizing and placement and predict influence of pillar extraction or reduction on ground stability. Practical examples for pillar design and optimization in low seam gypsum mining operations and optimizing sequencing of pillar extraction in thick seam metal mining operations are outlined.

Jan 1, 2003

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By R. L. Grant

[Detonators are used to explode permissible explosives, dynamites, or other high explosives. This explosion or detonation is brought about by the energy which is liberated as a combination of concussion and heat when the detonator is fired. In Other words; "The detonator is the key which unlocks the energy of a high explosive" (8)4. Being sensitive and latently dangerous, detonators must meet two primary requirements: They must be safe to handle and must detonate when desired, thereby imparting detonation to the explosive charge.]

Jan 1, 1941

By L. L. Seigle

Free energies, heats, and entropies of mixing of solid Fe-Au alloys have been measured by the galvanic cell method between 800° and 900°C. A positive deviation from Raoult's law and a large excess entropy of mixing were observed, both attributable to lattice distortion caused by the disparity in component atom sizes. Since the terminal solid solutortiontions are not regular, thermodynamic properties computed from the location of the mis-cibility gap do not agree well with measured quantities. The electromotive force data suggest some changes in the existing Fe-Au phase diagram. ALTHOUGH a considerable amount of information has been accumulated about the thermodynamic properties of metal solid solutions which exhibit negative deviation from Raoult's law, particularly those in which ordering occurs, relatively few experimental measurements have been made on solutions with positive deviation. This is due to the infrequency of broad homogeneous regions suitable for experimental measurement in solutions of this type, since any marked positive deviations from ideality lead to restricted solubility and the formation of miscibility gaps. Thermodynamic data reported in the literature for such systems have usually been calculated from the location of the miscibility gap boundaries under the assumption that the entropies of mixing are ideal, i.e., the terminal solutions are regular.' One of the few binary systems with both positive deviation and a wide homogeneous range in the solid is the Ni-Au system. A recent investigation of solid Ni-Au alloys' revealed that the entropies of mixing were much larger than ideal and consequently thermal data computed from the phase boundaries assuming regular solutions were seriously in error. Theoretical considerations put forward by Zener indicated that high entropy values should generally be associated with systems possessing a miscibility gap in the solid, when this is due to differences in the size of component atoms. These facts suggest that the regular solution assumption is a poor approximation for many solid solutions with positive deviation and that reliable thermodynamic data generally cannot be obtained by conventional methods from the location of miscibility gap boundaries. The Fe-Au system, Fig. 1, resembles the Ni-Au system in certain respects. The presence of a miscibility gap in the solid indicates a large positive deviation from ideality, but there is nevertheless an extensive single phase region suitable for experimental measurement. The following investigation of solid Fe-Au alloys was carried out in order to obtain additional data on the thermodynamic properties of metal solid solutions with positive deviation from Raoult's law and to further compare thermodynamic data computed from miscibility gap boundaries with those measured experimentally. Experimental Method The thermodynamic properties were derived from measurements of the potential developed between pure solid iron and Fe-Au alloys in a high temperature galvanic cell. The experimental apparatus and technique were the same as those used for the Ni-Au alloys and described in a previous report.' Cell electrodes were 1/16 in. diam rods swaged from chill-cast ingots and annealed for one week at 850°C. The alloys were prepared by melting fine gold granules under argon with pure iron obtained from the National Research Co. The cell electrolyte was

Jan 1, 1957

By Charles Vaught, JON VOLKWEIN, ROBERT PETERS, ERICA HALL

Since 1999, the CWP level among miners with 25 years or more experience, for instance, has risen from slightly more than 4% to 9% (See Figure 1). While it is obviously necessary to protect all miners’ lungs, there is now a technology to improve the chances that new miners’ lungs will be protected from the day they begin work.

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

By N. K. Singo, J. D. Kramers

The reprocessing of tailings resources to extract gold on an industrial scale has become common practice. While these projects are common in the Witwatersrand basin, similar low-technology processes are not operational in smaller goldfields. This study explores the possibility of reclaiming the tailings dump of the Louis Moore Mine in the Giyani Greenstone Belt, investigates potential hazards to communities in the vicinity, and identifies mitigation strategies. Auger samples were taken from the Louis Moore tailings at depths of up to 5 m. Aqua regia leach analyses show Au concentrations of up to 1 g/t. Inferred estimations based on ordinary kriging (OK) and inverse distance weighted (IDW) methods put the residual Au resource in the Louis Moore tailings dump at 0.20 t. Reworking the tailings is viable, although a potential environmental risk exists in the form of elevated arsenic concentrations. Further exploration is required to determine the mineralogical associations of Au and As. Tailings reworking would assist in raising funds for mine rehabilitation. The secondary tailings could potentially be repurposed, which would provide employment and facilitate community development, as well as deliver environmental benefits.

Jul 1, 2021

By E. L. Garton

[Analyses of may crude oils produced in Louisiana are included in reports that t have boon published by the Bureau of Mines. The first report, giving, analyse of 6 Louisiana crude oils, was 3 published in 1921 and this was followed a year later by Report of Investigations 2416,4/ giving 7 additional analyses. The eleven most important of these analyses were incorporated in Bulletin 291.5/ issued in 1928 In 1934 analyses of 26 crude oils produced in southern Louisiana were published.6/ The percent report presents analyses of 72 additional samples of crude oil from 45 fields in 23 parishes In Louisiana.]

Jan 1, 1939

By P. Quinn

"The Venturi-aerated flotation column (VAC) is based on a reactor and separator design for a new generation of flotation machines. The reactor is a Venturi tube, where the air/slurry contact takes place with intensive aeration for efficient particle collection. The separator is a column of 1-3 m length that provides quiescent hydrodynamic conditions for effective separation of bubble-particle aggregates from the remaining slurry.Aeration in the Venturi tube occurs via two mechanisms: air dispersion and nucleation (cavitation). By forcing air through a restricted passage with a fast flowing slurry stream, air is dispersed into fine bubbles. Bubble formation due to cavitation occurs on the surface of particles in the low-pressure section of the Venturi, from dissolved air contained in the liquid.Size-by-size recovery and flotation rate constants were determined for a small-scale laboratory Venturi-aerated flotation column. The results were compared to those obtained in a laboratory 2.2 L Denver cell. It is shown that the Venturi-aerated flotation column has slightly slower flotation kinetics to the Denver cell, but with much higher flotation selectivity. A portable Venturi-aerated flotation column can effectively be used to investigate process or equipment problems in operating plants.INTRODUCTIONFlotation processes can generally be divided into two sub-processes: 1) selective collection of hydrophobic particles by air bubbles and 2) separation of bubble-particle aggregates from hydrophilic particles that remain in the pulp. The methods of aeration, or bubble generation, control the mechanism of particle collection by either collision with, and subsequent attachment to bubbles, or by in situ bubble formation on the surfaces of hydrophobic particles. A flotation device should provide optimal aeration conditions for efficient particle collection and a suitable hydrodynamic environment for effective removal of bubble-particle aggregates from the remaining pulp."

Jan 1, 2002

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By S. Slottee

The technology of making and using ?paste? from mine tailings is increasingly well known by the minerals industry. The primary applications are water recovery and ?stacking? of tailings with minimal use of dams and ponds. This paper highlights some applications, other than water recovery and stacking, that have come to the attention of a paste thickener equipment supplier. As generated by thickeners, paste (also called ?thickened tailings?) is a non-settling, relatively high concentration, suspension of solids that can be pumped. Paste deposits with an angle of repose, allowing minimal use of dams. High solids concentration allows more water recovery at the paste thickener than is achieved in conventional and high rate slurry tailings thickeners. This paper is based on paste as produced in a flow sheet that includes a thickener, underflow pumps that are typically centrifugal, transfer pumps that can be centrifugal or positive displacement, and a distribution system at the deposition site. Examples of paste applications other than water recovery or stacking include: ?mine? an existing tailings pond by removing slurry, recovering coal or iron ore values, and return the new tailings to the pond as a paste that does not res-suspend; use paste to seal an existing tailings pond from leaking to groundwater or to an underground mine; extend the life of an existing tailings pond by thickening the tailings to paste; move an existing dry tailings impoundment to a new location by slurrying, pumping, paste thickening, and redeposit; minimize the size of a filter by paste thickening the feed; operate a paste thickener and filter in parallel on a tailings stream with re-mixing to achieve a high solids concentration. The use of paste tailings technology has been expanding over the last 15 years. The applications, both implemented and under consideration, are increasingly diverse and include all minerals tailings. Tailings handling designers should always consider a paste option to the conventional slurry solution.

Jan 1, 2011

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By D Kavanagh, C Michaud

"A continuous improvement initiative was identified at Kalgoorlie Consolidated Gold Mine’s (KCGM) Fimiston open pit with the goal of reducing bench turnover time and increasing shovel digability by improving fragmentation around previously mined-out stopes. In the past, a higher number of blasts than normal would be required to get through a single excavation area where stopes were present. This is due to the limited reach capability of the drilling fleet from safe ground into restricted areas requiring the drilling of the shot to be done in a staged manner. In addition, the holes that were able to be drilled in the area did not remain open long enough to be loaded with explosives as a result of the poor ground conditions surrounding the stopes.Over the last 18 months, KCGM has trialled drill additives to improve blasthole stability, as well as introducing a remote drill rig allowing holes to be drilled in areas previously inaccessible by manned drill rigs. This has resulted in improved penetration rates in bad ground conditions, improved drill hole stability, better shovel digability, and an overall reduction in bench turnover of at least ten days on the benchmarked 126 days average per bench. KCGM is now in the final stages of the improvement project with the installation of a drill monitoring system on the fleet to allow live data transfer back to the office for analysis, as well as providing improved accuracy on drill holes in restricted areas.Citation:Michaud, C and Kavanagh, D, 2016. Reducing Bench Turnover Time and Improving Shovel Digability, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 19–27 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016