Search Documents

By Robert A. Harrow

This report documents the results of the development and installation of an illumination system for an underground coal mine Shortwall Mining Section. Also presented are the techniques used for the above ground test and evaluation of the lighting system prior to installation underground which resulted in the issuance of a Statement of Test and Evaluation (STE) from the Mine Safety and Health Administration, Technical Support, Beckley, West Virginia.

Jan 1, 1979

By Haruka Takeura, Tomoaki Murata, Kazunari Yoshida, Masato Adachi

"Pure magnesium is a material with high functionality, however, the cold drawing of this material is very difficult, that is why, until this day there are no optimal cold drawing conditions. Furthermore, cold drawing of pure magnesium wire shows a problem with internal defects that occurs under certain conditions. In this research, the aim is the suppression of internal defects, and final target is to create the optimal cold drawing conditions for pure magnesium wires. The first step is the investigation of the drawing limit by using 250°Cannealed wire. As a result, reduction of 10% per pass was chosen for stable wire drawing. However, in this case, it was found that internal defects occurred at total reduction of over 45% during drawing. Investigation of intermediate annealing conditions that can suppress internal defects, and influence on internal defect that the die half angle and reduction per pass. As a result, it was found that the drawing condition capable of suppressing internal defects most efficiently was 13% reduction drawing by using under 6°half angle die. Consequently, it’s possible to manufacture a cold fine drawn pure magnesium wire of 100µm, without defects in the center of the wire and hindering its mechanical properties.INTRODUCTIONMagnesium is a light and high functionality material that has high vibration absorbency, heat dissipation, electromagnetic wave-shielding and recycling efficiency (Conruy, 1989). However, proper cold wire drawing conditions haven’t been established, that is why warm or hot processing is commonly used (Oishi, Mori, &Kawabe, 2005). As a result, strength improvement of the wires is not possible, that is why the production of medical tools is disregarded. If it was possible to cold draw magnesium wires, the applications for material products would expand. Further, in wire drawing such difficult processing material, if appropriate processing conditions are not selected, defects will be generated inside the drawn wire."

Jan 1, 2017

Coal preparation plant simulators are used to study flowsheet alternatives and determine product quality and quantity that can be produced under various operating conditions for individual circuits. Some simulators also provide an estimate of the cost per ton of clean coal by determining the number and size of different processing units required for a specific raw coal tonnage and by computing both capital and operating costs for individual units. However, to the authors? knowledge, none of these simulators have the ability to optimize plant performance while satisfying multiple product quality constraints and selecting the most profitable flowsheet from many alternatives. A novel coal preparation plant simulator (SIU-Sim) that maximizes the overall plant yield using a robust optimization tool and selects the best plant cleaning circuit configuration based on maximum plant profitability is presented. The simulator also identifies the best operating conditions for individual circuits of a plant to satisfy multiple quality constraints for the overall clean coal product. It uses a genetic algorithms- (GA) based technique to maximize the overall plant yield for each cleaning flowsheet alternative and uses a net present value (NPV) analysis technique to maximize plant profitability for the entire life of a new plant or the remaining life of an existing plant. The step-by-step development of the simulator along with a case study demonstrating its specific features is presented.

Jan 1, 2008

By Guangyuan Li

A 3-D block-spring model (BSM) has been developed for simulating the behaviour of jointed rocks. The model uses a discontinuous formulation and an iterative procedure to solve the large displacements in jointed and faulted rock masses. The 3-D BSM has been used to simulate mining excavations in jointed rocks around an open pit and underground settings. The applications have demonstrated that it is a practical tool to solve complicated problems of rock mechanics in civil and mining engineering. This model has recently been modified to incorporate complex geological conditions, such as underground water flow (seepage), unstable blocks and the time-dependent behavior of backfill materials. To demonstrate the capability of the 3-D model this paper presents the fundamentals of the 3- D BSM and its application for open-pit mining. A complete computer package BSM3D has been developed based on the 3-D block-spring model. The package consists of a solving engine for numerical analysis and a Windows based processor for mesh generation and results display. The multi-functioned pre-processor provides tools and menus to help users setting up models easily and conveniently. The fully featured post-processor allows users to view the results in different windows and orientations. The graphical results include contours, vectors, animation of rock movement, and the failure state of the rock structures.

May 1, 2001

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

By C. Vipulanandan

Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.

By D. Harrington

Ventilation of underground workings consists of establishment of such control of air currents that the underground workers may work in safety, with maximum comfort and efficiency, mad without impairment of health; and that the mine openings may be made subject to such control of air flow as to remove from the workings at ordinary times harmful gases and dusts, and at time of emergency, such as fire or explosion, there may be maintained as much or as little air flow as may be desired covering portions of the mine or the mine in its entirety. Control of air flow is the keystone of any ventilating structure, and this very essential feature is obtainable only by the installation of mechanically operated fans, to ether with other ventilating devices such as doors, overcasts, regulators, etc. Every mine, large or shall, coal or metal, should from the outset be equipped with a fan. While much has been written about natural ventilation and many claims have been made that in specific mines there is sufficient natural al" flow, there are few if any mines, coal or metal, where natural ventilation supplies anything like adequately safe or healthful conditions for underground workers even at ordinary times; and at a time of mine fire or explosion the mines depending upon natural ventilation are practically helpless, and certainly are decidedly dangerous to those unfortunates forced to be in them.

Jan 1, 1933

The following report summarizes the results of engineering feasibility studies whose purpose was to assess the probable efficiency, reliability, safety and cost of a number of possible methods for removal of radon gas from the ambient air in underground mines. Fourteen candidate techniques were evaluated. Seven of these were based on specific individual principles, and seven were based on combinations of these principles. The individual principles were as follows: 1. Activated charcoal 2. Organic fluids 3. Semipermeable membranes 4. Molecular sieves 4. Cryogenics 6. Chemical reaction 7. Centrifuge The combinations were: 8. Cryogenics and activated charcoal 9. Cryogenics and molecular sieves 10. Cryogenics and chemical reactions 11. Membrane filters and organic fluids 12. Membrane filters, cryogenics and activated charcoal 13. Membrane filters and chemical reactions 14. Silica and an Organic Fluid

Jan 1, 1975

By E. J. Lintner

This paper is one of a series being prepared by the Bureau of Mines describing; gypsum mining and crushing methods and costs at various operations throughout the, United States. These papers are designed to dissemminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to the individual operator as well as to the industry as a whole; on the other hand, operating costs are essential to the technical discussion and. study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the mining and primary crushing methods employed at the plant of the Ebsary Gypsum Co., Inc., Wheatland, Monroe County, N. Y. This company is capable of maintaining a maximum yearly production of 220,000 tons of crushed gypsum, thereby ranking as one of the largest gypsum operators of the State. The methods and practices employed typify the standard methods followed by gypsum producers in western Now York State, The bed of gypsum mined lies only 35 feet beneath the surface and is above average thickness for this vicinity.

Jan 1, 1937

By Steven D. Botts

The paper point out the Antamina's social policies with Huascarán National Park. The project had required the mine engage with the communities most affected by the mine development, its operation, and closure. In this sense, operating within this social context has required Antamina to first be effective in understanding who the affected people are –at the local, regional, national and international levels. This understanding is also a process that requires time. Through the HWG, the company has achieved engagement, as well as an understanding an appreciation of viewpoints and perspective that has resulted in the protection of HNP, as well as the timely development of the project, with support of stakeholders. Therefore, the experience of the HWG was become for other natural resource projects in complex settings, involving national and international stakeholders and protected or sensitive areas.

Sep 13, 2001

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

By Faruk Oksuz, Phillip L. Covell, Martin Doll

A series of difficult ground conditions causing high groundwater inflows and hazardous gas intrusion abruptly halted the construction of a 6.4-meter (21-foot) finished diameter and 1,890 meters (6,200 feet) long tunnel planned to serve as a 4-millioncubic meters (1-billion gallon) per day capacity river outfall for treated wastewater. Some 808-meters (2,650-feet) section of the constructed tunnel, TBM, and all other tunneling equipment were completely flooded with hydrogen sulfide laden artesian groundwater. The subsequent pumping and tunnel recovery efforts were unsuccessful and the tunnel was abandoned. In the end, the construction contract was terminated and options to redesign and reconstruct the project were re-evaluated to maximize the use of already constructed tunnel facilities such as the construction access and inter-mediate shafts and six outfall diffuser shafts in the river.

Jan 1, 2007

By Samuel Canchanya M

El presente trabajo señala la eficiencia de los métodos geoestadísticos en la industria minera a través de diversos ejemplos aplicados en yacimientos peruanos. En este sentido, los métodos estadísticos desplazan a los métodos tradicionales puesto que ofrecen mayor precisión, objetividad y eliminan la relativa accesiblidad de los depósitos minerales. Asimismo, el texto describe las diversas explicaciones de su aplicación en el campo de la ingeniería industrial, topografía, geofísica y batimetría en la industria del petróleo, al tiempo que refiere las causas de su escaso empleo como método teórica en la explotación de la industria minera.

Nov 8, 1984

By M. Arias

"An attractive foreign investment legislation, an anti-mining framework in the jurisdiction where a head office is located, the geographical location of the mineral resources, a country that offers the technology needed by the industry for its operations -- these are some of the many factors that make mining and mineral exploration a global business. It is precisely in the complexity of this new era of globalization and market environment, that sustainability initiatives are challenged. Responsible management of mineral exploration and mining is no longer defined by the use of efficient technology and resource management. Sustainability is not only a report compliance exercise or a green revolution. Sustainability is like any business, a long term profitable proposition. This new approach encompasses four pillars: social, economic, environment, and culture. This new approach connects humans and corporations; it is the way to engage, respect and improve relations with the people with whom we work and our neighbours."

Jan 1, 2011

By Sidmar Aparecido Ceresani

O presente estudo tem como objetivo demonstrar a cinética de recristalização e o amolecimento da liga C272000 processada na laminação a frio com uma deformação de 75%. Para determinar o modelo cinético Johnson, Mehl e Kolmogorov (JMAK) foi adotado a temperatura de 450° entre 5min. a 50min. Restaurando totalmente a microestrutura deformada plasticamente sendo progressiva a elevação do tempo e da temperatura. A caracterização microestrutural das amostras foi utilizado microscopia óptica e metalografia. Conclui-se que o modelo JMAK satisfaz a forma de nucleação da recristalização da liga C272000.

Oct 30, 2017

By Kjell Winther

"Hydralift Scanmec introduced early in the eighties a new and different mill design for very large grinding mills. The design described has actually no size limitation upwards and is so far suggested with motor power up to 40 MW. The mill is furnished with gearless ring motor drive transmission. It is totally fabricated, without heavy castings. The first installation, an 8, 1 MW ball mill dia. 6,5 m x 9,65 m length, has been in continous operation in 13 years without problems. Total grinding costs has been reduced with 3 0% compared to traditional smaller mills. Reductions has been achieved in maintenance cost, power consumption, liner wear and grinding media consumption.So far 3 ball mills of the described design are delivered and in operation, one grinding Iron ore and two grinding Nickel ore.IntroductionThe design of mills for mineral ore dressing has basically been unchanged since grinding in mills started some I 00 years ago, in spite of the fact that mills have grown larger and larger. This has resulted in structural and mechanical problems, causing expensive failures and loss of production.Hydralift Scanmec engineers were designing mills for more than 20 years according to the old «rules». As they experienced interest for an increase in the mill size at the time when reports about failing mills were published, they started analyzing the different mill parts to find new solutions. One goal was to only use elements from proven technology in the new design. Two key items were ring motor (wrap around motor)(Isch et al. 1977, Meintrup and Klein 1982, Ranze 1983) and large diameter pad bearings (wrap around bearings)(Fuller 1984), both acknowledged from other industries."

Jan 1, 1995

By Patrick J. Hannigan

The pile foundation designer typically performs a subsurface exploration program and static pile capacity calculations before selecting a pile foundation type, length, and capacity. During construction, a pile installation criterion must be established to meet these design requirements. This installation criterion usually consists of a minimum penetration resistance or blow count to confirm pile capacity and may also include a minimum embedment requirement. This text will focus on use of wave equation analysis and dynamic measurements to meet design requirements. BEFORE THE WAVE EQUATION Since the mid-1800s, over 450 dynamic formulas for pile driving control have proliferated. In their simplest form, these formulas relate hammer energy to the work of soil resistance, or simply: W ? h = R ? s (1) Where W = ram weight h = ram drop height or stroke R = pile capacity s = pile penetration per blow

Jan 1, 1990

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By S. Fawell, H. R. Manouchehri

The main electrophysical properties, i.e., dielectric constant and electrical conductivity, of pure calcite, quartz and wollastonite mineral samples were measured and their triboelectric charge attributes were investigated by contacting minerals particles with different tribochargers made from different materials. In addition the energetic work function values for mineral samples were estimated due to their acquisition charge. Besides, the behaviour of triboelectrically charged of different particle size fractions of mineral samples were inferred. Finally an attempt were made to translate the findings from single mineral systems to a real carbonate ore. The results exposed good prospects to beneficate the examined minerals by triboelectric separation.

Jan 1, 2002