Search Documents

Preface The intention of this paper is to provide the reader with knowledge gained here at Memorial University regarding the practical use of the Bruker SDD x-ray detector for applications in image analysis. Included below are descriptions of the detector’s characteristics and observations regarding precautionary use. What is described below is relevant to the XFlash® model 3001 detector only, whereas the model 4010 is the new and currently available detector. The manufacturer has provided up-to-date information and a figure that presents very different behaviour relative to the characteristics described in this paper. That information and figure is also included here as an addendum (see figure 9). Introduction It has been more than two decades since an image analyzer has been proposed based on the unique imaging characteristics and spatial resolution provided by the scanning electron microscope (SEM) together with energy discriminating x-ray (EDX) acquisition (Reid et al, 1984). From the inception of technique, technology of the day has played the major role for making applications increasingly more practical. Computers, digital imaging, and softwares together with computer automation of modern digital SEMs have all played their part in advancing the technique to where it is today.

Jan 1, 2007

The cyclone, or centrifugal separator, ,is firmly established in industry as a low cost separator of solids from gases.While it will also separate fluids of different densities, and solids from liquids, its main use is to remove relatively fine dusts from gases whose pr~erties are generally not greatly different from those of air. This latter phase of operation is the one that will be dealt with here.The duty of such a cyclone separating system is to take in a supply of dusty gas and separate it into its components of dust and clean gas as perfectly as possible for the least consumption of pressure head. Any separation at all causes pressure loss and, in general, the greater the separation, the greater the pressure drop needed to effect it. The percentage of dust in suspension which is separated from the gas-dust mixture is commonly called the collection or separation efficiency. Overall or "true" efficiency must take pressure drop into account and may be considered as proportional to the ratio of the percentage of dust collected to the resultant pressure drop. For any cyclone It will vary with different dusts.Many commercial adaptions of the simple cyclone are made solely on the basis of pressure drop improvement, without taking into account the effect on separation efficiency, probably because the latter is so difficult to assess correctly. It appears unfortunate but true that the majority of such adaptions and patent gadgets fitted to cyclones which decrease pressure drop, do have an adverse effect on separation. In other' words, the true efficiency is seldom increased but often diminished.Without a knowledge of what actually goes on inside a cyclone, it is impossible fully to appreciate the real effect of a modification. For instance, it is on record that a cyclone...

Jan 1, 1949

Las primeras exploraciones de la atmósfera Jibrese se iniciaron en 1934 por medio de los vuelos a alturas de 6,000 m. y globos pilotos. En 1938 J. A. Broggi, G. Petersen G. y G. H. Wagner practicaron una serie de ascenciones de globos pilotos. En ese sentido, se describe una reseña histórica y una interpretación de las cuatro capas de vientos al ser observados sobre Lima (Perú) y datos sobre las temperaturas observadas en las alturas de 6,000 y 12,500 m.

May 1, 1958

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic meters per hour) for dozers operating in hard-rock bulk push applications. The particle size distribution of the material employed in the test rig was modeled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard-rock dozer push operations. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 to 40 m.

By H. M. Thorne

The Union of South Africa has been interested in oil shale for a long time, and deposits of oil shales, torbanites, and similar rocks have been found in many parts of the country. (Fig. 1.) Samples differ markedly in oil yield and in the characteristics of the oil. The strata vary in thickness, and most of the deposits that have been found are in unfavorable locations because of remoteness from markets or absence of transportation facilities. This report deals mainly with the torbanite deposit near Ermelo, Transvaal, in the Union of South Africa, and the operations of the South African Torbanite Mining and Refining Co., Ltd. (hereafter referred to as Satmar), in mining the torbanite, retorting it, and refining the crude oil.

Jan 1, 1954

By T. Chong, R. Pesalj, B. Marchant, Z. Nikic

"The Mount Polley copper/gold project is located in central British Columbia and is currently being developed by Imperial Metals Corporation. Extensive laboratory and pilot plant testing was required to develop acceptable metallurgy for recovery of both sulphide and oxide copper-gold mineralization. Copper recovery is highly sensitive to oxide copper content of the feed whereas gold is primarily associated with the copper sulphide minerals. A conventional flowsheet where sulphide flotation is followed by sulphidization and oxide scavenging is described. The conventional flowsheet was used in a feasibility study which resulted in a favourable production decision at Mount Polley. Detailed engineering and permitting are in progress.More recently, laboratory and pilot testing of a new flotation reagent, S-6493*, an oxide specific collector, has indicated that improved copper recovery can be accomplished with reduced reagent consumption, including elimination of the sulphidization step, using S-6493 compared with the conventional flowsheet. The comparative metallurgical results using S-6493 and conventional sulphidization methods are presented, from both bench scale and pilot testing. Comparative economics of the conventional flowsheet and that using S-6493 are also presented. Advantages of S-6493 include reduced reagent costs, increased revenues from additional copper recovery, and overall reduction in capital and plant operating costs due to the simplified flowsheet. INTRODUCDONThe Mount Polley copper/gold property is located in Central British Columbia, 56 air kilometres northeast of Williams Lake. The first recorded exploration was in 1964. By 1989, a total of 238 diamond drill holes, totalling 27, 522 meters, was completed to detail reserves on the Mount Polley prospect. A number of drill core composites were submitted, containing a variety of oxide copper levels, for metallurgical flowsheet development. Six bulk samples were collected from surface trenches for additional bench scale testing and for pilot plant testing."

Jan 1, 1991

By T Hughes

Upward pressure on all mining operations is coming from the triple bottom line. To some extent this is being offset by the rise in mineral prices, but this may or may not continue. The other serious issue facing all companies is the replacement of economic reserves as exploration levels over the past decade continued to decline in line with falling mineral prices. In order to underpin the sustainability of the mining industry it is necessary to continue to reduce cost, reduce the mine environmental footprint, whilst increasing community benefit. At the same time it is imperative that we increase the economic reserves. The highest risk is in adding new mineral discoveries as the strike rate for economic discovery decreases. Gekko Systems Pty Ltd recognises that the most simple and risk averse route to increasing economic reserves is to reduce cut-off grade in the mine, thereby bringing formerly uneconomic reserves into the economic category. We have been developing a new process flow sheet which embodies the triple bottom line and the issue of economic replacement of reserves. This paper describes this flow sheet and presents four examples where this concept is/can be applied to bring about triple bottom line benefits. Sustainability can only be assured if we are the ones in control of our environment, costs and reserves.

Jan 1, 2007

By J. P. Harrison, M. Grenon

"This paper summarizes the results of numerical studies on drift stability in moderately jointed rock masses. It investigates the relative pertinence of geomechanical factors such as joint orientation, spacing and stress regime. This is undertaken using a distinct element model and a series of parametric studies. IntroductionIn evaluating the stability of drifts in jointed rock, it is often necessary to compromise by employing models that capture the complexity of the rock mass, but which are still simple enough to allow for their routine implementation. The distinct element method can arguably provide an eloquent method to accomplish this. This paper explores the applicability of the method by means of a parametric study aiming to identify the dominant factors that influence the stability of drifts in moderately jointed rock. To this end a commercially available 2D distinct element numerical model was used. A series of techniques are presented in an effort to quantify the results of any instability predicted by the model.This paper also demonstrates a case study where a 3D joint network model was integrated into the distinct analysis software package. The advantages, as well as the current limitations of this approach, are discussed."

Jan 1, 2001

By J. R. Cobble

Dissolution of chalcopyrite with acidified ferric sulfate produces a sulfur layer on the unreacted chalcopyrite surface that interferes with further dissolution. The U.S. Bureau of Mines has developed a process to improve the leaching kinetics of these types of diffusion-controlled systems. The system features the Bureau-developed turbomill, an attrition grinder that scrubs the reaction product coating away from the unreacted mineral grains during leaching. The system can be operated continuously at any temperature up to the boiling point of the leaching agent. This method is a hydrometallurgical alternative to chalcopyrite smelter technology and eliminates sulfur dioxide emission problems with its associated costs. Batch testing at 900 C with the chalcopyrite-ferric sulfate system resulted in copper extraction exceeding 99 pct. At an optimal energy consumption of 1,520 kW· hjst, 95 pct of the copper was extracted. The pregnant liquor was clarified and tested for typical solvent-extraction recovery of the copper. Two-stage extraction and two-stage stripping recovered 96 pct of the copper in an electrolyte suitable for copper electrowinning.

Jan 1, 1993

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By C. E. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it 'is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required. Versluys4 has presented a mathematical analysis of the vertical flow of oil and gas mixtures which covers the fundamental theories of the problem-although, as he points cut, there are factors, particularly friction, slippage, and solubility of the gas in the oil that must be mown or determined experimentally before the equations he has developed can be applied to actual

Jan 1, 1933

By Pascoal Ferrari Pedrosa

Neste trabalho é apresentado os resultados de um estudo experimental com tijolos de solo-cimento vazado, com diferentes adições de resíduos de borracha vulcanizada oriundas da indústria de recauchutagem de pneus. Foram realizados ensaios de caracterização do solo utilizado, das composições desse solo com resíduos de borracha e das misturas de solo-cimento produzidas com essas composições. Conforme os resultados de ensaios realizados em corpos-de-prova cilíndricos e em tijolos de solo-cimento, verificou-se que: ainda não é possível a introdução do resíduo de borracha de pneus de pneus em blocos de solo-cimento, pois não atendem características da NBR-10834 [4] e precisam ser melhor avaliados.

Aug 16, 2017

By BUREAU OF MINES

This report is submitted in accordance with the provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1953 has been divided into two separate publications. Each has been published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5043, Part I - 011 From Coal. R. I. 5044, Part II 011 From 011 Shale. - Identical in each report, the introduction summarizes research progress made in 1953 under the entire Synthetic Liquid Fuels program. A free copy of each of these publications may be obtained by a written request to the Bureau of Mines, Publications Distribution Section, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Apr 1, 1954

By J. T. Nel

Non-transfer-arc linear plasma systems are highly suited to manufacturing nanoparticles. In this paper, the manufacturing of such particles with specially designed plasma systems is discussed. In general, it entails the volatilization of a metal halide that is injected in the high-temperature region of a plasma flame, where it is reacted with a suitable reagent, for example O2, to produce nanooxide powders. Metal powders can also be introduced directly in the plasma. Due to the very short residence time of only milliseconds in the reaction zone, as well as the fact that the reaction takes place in the gas phase, combined with very rapid quenching in the order of 10 000°C.s-1, nanoparticles are produced. At Necsa the manufacturing of such particles has been demonstrated on various scales. A pilot plant for the production of nano-Al2O3, and two pilot plants, one using SiCl4 and the other one using SiF4 as feed material, were built to produce fumed, pyrogenic, nano-SiO2. The alumina plant had a production rate of 8?10 kg.h-1 and the silica plants had production rates of 2 and 10 kg.h-1 respectively. Perfectly spherical alumina particles with a particle size distribution of between 10 and 200 nm were produced on a continuous system. Particle size analysis for the silica by SEM measurements showed a d50 of 60 nm and a particle size distribution of 30?100 nm. The specific surface area was in the range of 170m2.g-1. Other samples of plasma produced nanoparticles such ZnO and B4C will also be presented.

Jan 1, 2010

By Hemingway P, Boag J

Major operating aspects of the Mary Kathleen Uranium Ltd. treatment plant are discussed with partkular reference to those which are peculiar to this operation.Problems associated with the production of a penalty free uranium oxide product are examined and the methods developed to overcome them are described in detail.INTRODUCTIONMary K,athleen Uranium Ltd. is the largest of the Australian uranium producers. The flow-sheet is based on fine grinding, standard sulphuric acid leach, ion exchange concentration, and magnesia precipitation of the final product, with certain modifications introduced as the result of pilot plant investigations at the South Australian Department of Mines Research Laboratories in Adelaide.The plant commenced operations in June, 1958, attained design tonnlige of 1,120 tons per day in September of that year and has since operated continuously with a throughput in excess of 1,000 tons per day. Pilot plant recommendations generally have been followed, and predicted results have been attained. The only exception has been the silica and rare earth content of the product produced during the early months of operation. Considerable modification of the early resin regeneration techniques resulted in the reduction of the silica content of the product to within specification limits. Research work in the ion exchange section has also resulted in the reduction of the rare earth content of the product to below specification levels. All product now being produced is completely within the agreed specification limits of impurities.

Jan 1, 1961

One of the seminal pioneering papers in reserve evaluation was published by Danie Krige in 1951. In that paper he introduced the concept of regression techniques in providing better estimates for stope grades and correcting for what later became known as the ‘conditional bias’. In South Africa, the development of this approach led to the phenomenon being dubbed the ‘regression effect’, and regression techniques ultimately formed the basis of simple kriging in Krige’s later papers. In the late 1950s and early 1960s, Georges Matheron (1965) formulated the general theory of ‘regionalized variables’ and included copious discussion on what he termed the ‘volume-variance’ effect. Matheron defined mathematically the reason for, and quantification of, the difference in variability between estimated values and the actual unknown values. In 1983, this author published a paper that combined these two philosophies so that the ‘regression effect’ could be quantified before actual mining block values were available. In 1996 and in some earlier presentations, Krige revisited the regression effect in terms of the conditional bias and suggested two measures that might enable a practitioner of geostatistics to assess the ‘efficiency’ of the kriging estimator in any particular case. In this article, we revisit the trail from ‘regression effect’ to ‘kriging efficiency’ in conceptual terms and endeavour to explain exactly what is measured by these parameters and how to use (or abuse) them in practical cases.

Jan 1, 2015

By Dimitrios Litsas, Michael Kavvadas, Panagiotis Sitarenios

"The paper discusses the results of 3D finite element analyses to investigate the effect of face support pressure and soil permeability on face stability conditions in EPB tunnelling. Two main types of face behavior are identified: Undrained conditions ahead of the tunnel face, typically occurring in soils with permeability less than about k=5·10-7m/s, are shown to be favourable for face stability; analyses show that an applied face pressure comparable with the initial hydrostatic pore pressure is sufficient for adequate face stability, even for soils of relatively low strength. Drained or partially conditions, typically occurring in soils with permeability higher than about k=5·10-6m/s, show that face stability is strongly dependent on the horizontal effective stress of the muck in the excavation chamber; the presence of even a small effective stress in the muck is very beneficial for face stability conditions and can be a possible explanation of successful EPB tunnelling through relatively permeable soils. INTRODUCTION Face stability is probably the most important aspect in urban tunnelling. Usually, Earth Pressure Balance (EPB) machines are utilized, to ensure that a reasonable amount of face pressure is exerted on the advancing excavation face, reducing ground loss and preventing potential instability of the face core, thus controlling the amount of disturbance caused by tunnel excavation to surface structures. However, the ideal amount of face pressure depends on several factors (ground and groundwater conditions, tunnel size and depth, muck conditioning, etc.) which are difficult to include in analytical calculations. For many years, conventional empirical or analytical methods (e.g. Anagnostou & Kovari 1996) were the only available tools for quantifying face stability and selecting the required face pressure. In the last few years, however, numerical analyses have gained power over conventional methods, allowing more accurate designs and providing useful information about the anticipated ground deformations due to tunnelling. Numerical analyses have also been used in assessing safety against face instability using face extrusion (horizontal face displacement) calculations (e.g. Prountzopoulos 2012)."

Jan 1, 2016

By S. Gorzalczynski

The recent trend in underground mine developments is “bigger is better.” This is most certainly evident in the mine shaft and conveyances that operate within its compartments. Today, there are several new installations requiring mine cages that can transport up to 170 passengers. The technology in mine hoisting is advancing to address a combination of higher capacity requirements, deeper hoisting depths and faster winding rates, however, some areas of the hoist plant have not changed in the past 50 years. The most notable of these areas is the shaft compartment guide string and the conveyance mounted safety arrest mechanism. The technology in use today for the protection of passengers in a shaft conveyance from a hoist rope severance incident remains conceptually unchanged from Elisha Otis’ design of 1850. The actual retardation components, the safety dogs, have taken on several forms since Elisha’s invention with the last major design change occurring in the late 1940s. The arrest of a free falling shaft conveyance requires that the shaft guides withstand the energy imparted on them by the safety dogs. There are some very real limitations presented by the use of wood for this application. The new hoisting era will most certainly continue to demand larger capacity equipment, but also an increased awareness toward safety

Jan 1, 2002

By E. P. Youngman

Zirconium, formerly distinctly a rare element, is rapidly becom- ing of rather extensive commercial importance. Economic features of the zirconium industry, together with general information regarding the metal and its compounds, are discussed in a separate paper, to which this paper is a supplement. In addition to giving a brief discussion of the four or five de- posits that so far have proved to be commercial sources of the element, this circular summarizes available data (including some hitherto unpub lished material from the files of the Bureau of Mines) upon other occur- rences, including many of scientific interest only, of the two commercial. minerals, zircon and baddeleyite, and also data upon some of the minor minerals, such as eudyalite and cyrtolite, which have attracted addition- al interest in recent years because they are frequently richer in hafnium than the more common zirconium minerals.

Jun 1, 1931