Search Documents

By M. L. Hammond, G. M. Bowers

Silicon dioxide films have been prepared on silicon wafers by the oxidation of SiH, near 400°C. Results previously reported by Goldsmith and Kern7 have been qualitatively corrobovated using a system of different geometry, and significantly greater deposition rates have been achieved. The deposition rate is independent of thickness and nearly independent of the O2/SiH, ratio over a wide range; however, the rate is strongly temperature-dependent. The structure of the deposit depends upon the cleanliness of the substrate, and the electrical field strength of the deposited oxide depends upon the nature of the electrodes. MULTILEVEL interconnects in integrated circuits using aluminum metallization require an insulator that can be deposited at low temperature. Because the A1-Si eutectic is only 577°C, the maximum deposition temperature must be below about 500°C to prevent reaction of the aluminum with the silicon and with other materials in the integrated circuit. Many methods of depositing insulating films of SiO, and other dielectrics have been reported'-6 but the technique described by Goldsmith and Kern7 offers the simplest method of preparing SiO, films. The technique involves the reaction of SiH, and 0, to form SiO, films in the 300" to 500°C temperature range. Previous work using this gas system has been reported8 and the initial development work at Philco Microelectronics was done at the East Coast R&D Laboratories. 9 This paper corroborates some of the results of Goldsmith and Kern,7 shows that much higher deposition rates can be obtained than previously reported, and presents some observations on the structure of deposited SiO, films. EXPERIMENTAL CONDITIONS Fig. 1 is a schematic drawing of the apparatus used in this study. It differs from that of Goldsmith and Kern in that 1) the gases are mixed before they enter the reaction chamber, 2) there is no fritted glass diffuser, and 3) the wafers are stationary during deposition. The control thermocouple was in a well located 0.06-in. from the substrate, and three gas supplies were used: 1 pct SiH4 in N 2, O 2, and N 2. Water vapor must be excluded from the plumbing to prevent the formation of colloidal SiO, and the SiH4 must be diluted with an inert gas because SiH4-0, mixtures are extremely flammable above about 4 pct SiH The wafer temperature was determined by attaching a thermocouple to a test wafer and the temperature was maintained to +5 C. The conditions used in this investigation are listed in Table I. The temperature range was chosen for compatibility with the A1-Si system. The volume ratio of 0, to SiH4 is the actual volume of 0, delivered to that of SiH4, taking into account the initial dilution of the SiH4. This ratio, which was used by Goldsmith and Kern,7 is a useful indicator of the experimental conditions. The active/inactive ratio is the ratio of the volume of active gases, SiH4 and O2, delivered to the volume of dilution gas. The active/inactive ratio is an important parameter to specify for deposition rate determinations since it determines the amounts of reactants that arrive at the sample per unit time. Fairly high dilution ratios were necessary to achieve uniform deposits of SiO,. Most of the process characterizations were performed on the polished (111) face of 3 to 5 ohm-cm, n-type silicon wafers which were 0.009 in. thick; but the data approximately apply to deposition of SiO, on thin films of aluminum. It is difficult to obtain accurate deposition rate data over aluminum films because of coarsening the aluminum surface during exposure to 300" to 400°C. The deposited SiO, film fol-

Jan 1, 1969

By William E. Ford, Edward Salisbury Dana

WheweUite. Calcium oxalste CaCz04.Hz0. In small colorless monoclinic crystals. Optically +. j3 = 1.555. From haxony, with coal; also from Bohemia, and Akace. Oxammite. Ammonium oxelate, (N&)rC20r.2HzO. From the guano of the Gudape Isbnds, Peru.

Jan 1, 1922

By M. S. Burton, J. E. Ritter

The sessile-drop technique was employed to study the effect of atmosphere and alloy additions of titanium and chromium on the surface tension and contact angle of nickel on sapphire substrates at 1500oC. Shear tests were conducted on the solidified sessile drops. The liquid-gas surface tension of pure nickel on sapphire was found to be 1747 ergs per sq cm, with a contact angle of 109.6 deg. The surface tension and contact angle were not affected significantly by the four atmospheres, vacuum, impure argon, pure argon, and pure hydrogen. Small additions of titanium and chromium decreased the contact angle and for the same alloy content, contact angles were lower in pure argon than in pure hydrogen. On the basis of shear-test results , the most probable cause for adhesion in the Ni-Al2O system is the formation of NiO:Al2O3 spinel at the interface; in the titanium alloy-Al2O3 system adhesion is thought to be due to a mechanical interlocking effect; in the chromium alloy-Al2O3 system adhesion is believed to be the result of solid-solution formation involving Cr2O3 and Al2O3 at the interface. In the last few years there has been considerable interest in reinforcing metals with ceramic whiskers. It has been postulated that, by reinforcing nickel with sapphire whiskers, high-temperature strengths su- perior to those of the best current nickel alloys can be achieved.' To fabricate a whisker-metal composite having optimum density and strength, understanding of wettability and adherence in the system is of prime importance. Although there has been some previous research in this a a need for further studies has been cited4-8 to understand better the effects of impurities, alloys additions, and atmosphere on the wetting and bonding of metals to metal oxides. The purpose of this research was to investigate the factors involved in the wetting and adherence of nickel/nickel alloys to sapphire (single-crystal a Al2O3). Sessile-drop experiments were conducted in vacuum, impure argon, pure argon, and pure hydrogen, to determine the effect of atmosphere on the contact angle of the metals on sapphire, and the liquid-gas surface tension of pure nickel. The solidified sessile drops were sheared from the sapphire substrate to measure the bond strength between the metal and ceramic. The alloy additions chosen were titanium and chromium since both enhance the wetting of nickel on sapphire.2, 3c Also, titanium is commonly used when brazing metal-to-ceramic seals to improve adherence. Since chromium forms an oxide that is completely soluble in sapphire, it was thought that the oxide could serve as a transition phase to promote bonding between the Ni-Cr alloy and sapphire. I) EXPERIMENTAL APPARATUS AND PROCEDURE The sessile-drop apparatus was a horizontal furnace, with an induction-heated, cylindrical molybdenum susceptor in a water-cooled Pyrex chamber. This apparatus was patterned after that of Williams and Nielsen.7 A flat Pyrex window at each end of the furnace allowed temperature measurements to be made at one

Jan 1, 1968

By B. E. Grant

THE major metal mine operations of the United States Smelting Refining and Mining Company in Utah are in the Bingham area. The Company also owns and operates metal mines in the Ophir district, twelve miles south of Bingham, and in the Tintic district, 28 miles south of Ophir. Operations of the Company in the Park City area have been idle since early in World War II. These mining camps, lying at moderate elevations, serviced by railroads, hard-surfaced highways, in close proximity to mills, smelters, cities and towns, fertile valleys, winter and summer vacation areas, and airports are probably as favorably situated as any mining camps in the world. The Bingham district, known principally for its copper production from

Jan 1, 1948

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke's Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty's work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke's Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970

By Sandford S. Cole, John S. Breitenstein

The recovery of over 80 pct of the vanadium values in titaniferous magnetite from Maclntyre Development,Tahawus, N. Y., was accomplished by an oxidizing roast with Na2O3-NaCI addition. Process description is given for leaching of roasted ore and precipitation of V2O5 and Cr2O8 from leach liquor. THE exploration and development of the Mac-Intyre orebody at Tahawus, N. Y., by the National Lead Co. provided a source of vanadium. Analyses of various composite sections of the drill cores of the MacIntyre orebody were made to establish whether or not the vanadium was constant throughout. Ten drill cores were sampled as 50 ft sections, crushed, and a portion magnetically concentrated. The head and concentrate were analyzed for total iron and vanadium. The results on the concentrates indicated that the vanadium is associated with the magnetite and maintains a close ratio to the iron content. The nominal ratio of 1:25:140 of V: TiO2:Fe was found to exist in the concentrates. Typical value for the vanadium in the magnetite both from laboratory concentration and mill production is 0.4 pct. The recovery of vanadium from the magnetite was investigated in 1942 to 1943. The research program encompassed both laboratory and pilot-plant work on sufficient scale to provide adequate data to establish the feasibility of a full scale plant. The recovery of vanadium from various ores has been reported in the literature and has been the subject of many patents. The literature dealing with recovery from titaniferous ore by roasting is quite limited. Roasting with alkaline sodium chloride, sodium chloride or alkaline earth chlorides, and sodium acid sulphate have been claimed in various processes as effective means.1-8 The reduction of the ore, followed by acid leaching, was another method proposed.'-' "he use of various pyrometallurgical processes for recovery of vanadium in the metal or in the slag has also been extensively investigated, but the results had little application to the problem."-" The separation of vanadium values from subsequent leach liquors and vanadium-bearing solution has been the subject of a considerable number of papers and patents. The most practical is by hydrolysis at a pH of 2 to 3 by acidifying a slightly alkaline solution. Data on solubility of V²O5 and V2O4 in water and in dilute sulphuric acid indicated a solubility of 10 g per liter in water.'" Laboratory Results Magnetite Analysis: Adequate stock of magnetite was provided so that the laboratory and pilot-plant operation was on ore representative of the mill production. The ore was analyzed chemically and examined by petrographic methods to ascertain whether the vanadium was present in combined state or as an interstitial component between grain boundaries. No evidence was obtained which would indicate that the vanadium was in a free state as coulsonite.15 The analysis of the ore was as follows: Fe²O³, 47.4 pct; FeO, 29.1; TiO,, 10.1; V, 0.40; and Cr, 0.2. The screen analysis of the ore on the as-received basis was: -20 +30 mesh, 28.8 pct; —30 +40, 18.9; -40 +50, 9.7; -50 +60, 15.1; -60 4-100, 5.9; -100 + 200, 11.2; -200 +325, 3.7; and -325, 7.2. Roasting Conditions: The prior practice indicated that a chloridizing roast with or without an alkaline salt had been effective on other titaniferous magnetites. On this basis roasts with additions of sodium chloride, sodium carbonate and mixtures thereof were investigated varying the roasting temperature between 800" and 1100°C. Since the ore had shown no segregation or concentration of vanadium, the influence of particle size on the freeing of vanadium by the reagents during roasting was determined. The initial work was on silica trays in an electric resistance furnace with occasional rabbling of the charge. Subsequently, the roasting was carried out in a small Herreshoff furnace to establish the influence of products of combustion on the recovery of the vanadium. The laboratory tests showed that this ore required an alkaline chloridizing roast, in conjunction with a reduction in particle size to less than 200 mesh. When roasted in air at 900 °C with 5 pct NaCl and 10 pct Na2CO³, over 80 pct recovery of the vanadium was attained as a water-soluble salt. The presence of alkaline earth elements gave detrimental effects and care had to be exercised to avoid any contamination of the ore or roast product by such materials. The solubilization of vanadium under the various conditions is given in a series of curves in Figs. 1 to

Jan 1, 1952

By IRVING H. WENTIVORTII

(New York Meeting, February, 1912.) THE little town of San Nicolás, Tamaulipas, Mexico, lies approximately 60 miles east of Linares, situated in the State of Nuevo Leon, and 150 miles SE. of Monterey, as shown in the sketch-map. Fig. 1. The place is reached from Monterey by the Tampico train as far as Linares, a distance of 92 miles, and then by coach the rest of the way. It is situated in a narrow valley between low hills, the houses forming one main street and a plaza. It is peopled by about 500 inhabitants. The climate is temperate, the thermometer ranging from 90° in summer to a few degrees below freezing-point in winter; but this severe weather only lasts a day or two at a time, when the " northers " blow. There are no streams in the vicinity, but water sufficient for the use of the people is obtained from wells. The rainfall is about the same as that in the rest of NE. Mexico. The rainy months are July, August, and September. The rest of the year is practically dry, with an occasional showery day or two during the winter, when a " norther " is blowing. Timber is abundant in many localities. There are two varieties of oak, besides mesquite, ebony, "maguira," "patol," and a number of other kinds of trees indigenous to this region. I. HISTORY. On the discovery of the silver-lead hearing veins occurring in this district, the mining-camp of San Nicolás was founded in 1767 by the Spaniards, and numerous mines were opened and worked for a distance of abort 3 miles east and 5 miles west of the town. At the western extremity and near the Carrolena mine, a small town called San Pedro was built. The ruined walls of the houses form a single street, and all is over-

Aug 1, 1912

By T. F. Witherbee

It is proposed to give, first, a description of the works; second, a report of the first six months of the present blast; and third, such improvements as have been suggested by the practical working. The site selected for this furnace was, at the time of commencing work, October, 1872, entirely covered by the navigable waters of Lake Champlain. A coffer-dam was first built of cribs of round timber filled with stone, forming three sides, while the shore answered for the fourth. Considerable excavating was done with a steam-dredge, a hole being left for it to pass out. The opening was then built up, and the cribbing banked up with blue clay from the bottom of the lake, to render it water-tight and the dam pumped out; the remainder of the excavating being done by hand. All of the foundations, with the exception of the elevator-tower, and fifteen feet of the east side of hot blast, rest on the Potsdam sandstone, which forms the shore line, dipping into the lake at an angle of fifteen degrees. Owing to jogs in the formation, a much greater depth was found necessary than was at first anticipated, the foundation under the stack

By T. F. Witherbee

IT is proposed to give, first, a description of the works ; second, a report of the first six months of the present blast; and third, such improvements as have been suggested by the practical working. The site selected for this furnace was, at the time of commencing work, October, 1872, entirely covered by the navigable waters of Lake Champlain. A coffer-dam was first built of cribs of round timber filled with stone, forming three sides, while the shore answered for the fourth. Considerable excavating was done with a steam-dredge, a hole being left for it to pass out. The opening was then built up, and the cribbing banked up with blue clay from the bottom of the lake, to render it water-tight and the dam pumped out; the remainder of the excavating being done by hand. All of the foundations, with the exception of the elevator-tower, and fifteen feet of the east side of hot blast, rest on the Potsdam sandstone, which forms the shore line, dipping into the lake at an angle of fifteen degrees. Owing to jogs in the formation, a much greater depth was found necessary than was at first anticipated, the foundation under the stack

Jan 1, 1876

By W. M. Peirce

COAL'S importance in the metallurgy of zinc may be gauged by the fact that approximately a million and a half tons is so employed annually in the United States. This brief paper will show in what way the various steps in the treatment of zinc ores utilize this fuel, either in its primary form or as coke or gas, and to what extent. The first step in zinc metallurgy that requires the use of fuel is roasting the sulphide ore, which is the type of ore in which zinc commonly occurs. Since the roasting is nearly or completely autogenous, however, this use of fuel is too minor to warrant further attention. Concentration of zinc ores is usually carried out by conventional milling methods, but a pyrometallurgical method, the Waelz process, is used to concentrate certain low-grade ores, and to recover the zinc content of certain residues in concentrate form. The Waelz process uses a continuous rotary kiln in which a mixture of coal and zinc-bearing material is heated to a

Jan 1, 1948

By David P. Shoemaker, Clara Brink Shoemaker

The I phase was discovered by Bardos, Malik, Spiegel, and Beck1 in the V-Ni-Si system at 1100°C and in the Mn-Co-Si and Mn-Ni-Si systems at 1000°C. Kuzma and Hladyshevskii2 and Kuzma, Hladyshevskii, and cherkashin3 have reported a new phase, which they named the S phase, in the Mn-Co-Si and the Mn-Ni-Si systems at 800°C at approximately the I phase compositions. The powder diffraction diagrams of the I and S phases, compared by Bardos el al.,1 are related but show distinct differences in relative intensities. Professor Paul A. Beck kindly sent us a specimen of the (v-Ni-Si) I phase for single-crystal study. Precession and Weissenberg diagrams taken with a tiny single-crystal fragment showed that the structure is monoclinic with a large unit cell. The cell dimensions were refined from a powder diffraction diagram taken with CrKa radiation in a 57.3-mm camera with our computer program LSCELP4 using only the indices of those reflections that were observed on Weissenberg diagrams (hnl, with n = 0 through 9 and n = 12) and precession diagrams (Okl, lkl, Izk0, hkl, hk2). Table I shows the agreement obtained between the l/d values calculated with the final values for the cell dimensions and the l/d values observed by Bardos et al .1 for I(V42Ni33Si25), by US for I(V41Ni36Si23), and by Kuzma and Hladyshevskii2 for S(MnpCoSi). The powder patterns contain many broad and diffuse lines. In fact practically all powder lines observed are near-superpositions of several reflections. The refinement program is not set up to handle several reflections contributing to one observed line: the position of each line is refined with the aid of one set of indices only. The final values for the cell dimensions were obtained from the lines of strong or medium intensity with the indices indicated by asterisks in Table I: a0 = 13.403(6), bo = 23.336(15), co = 9.129(6)A ß = 99.11(6) deg The standard deviations (given in parentheses) are those calculated by the refinement program from least-squares theory and do not take into account that the lines included in the refinement may not have been correctly indexed in every case or that the position of a line may also be partly determined by the overlapping reflections. The agreement between the calculated and observed I phase patterns is fairly good, although some discrepancies occur. Not all observed lines could be indexed with the incomplete set of sin-

Jan 1, 1968

By G. A. Beiswenger

The application of the law of supply and demand to the sale of crude oil is generally conceded, but the motives underlying the buyer's (refiner's) demands are not always obvious to the seller (producer). In some cases this obscurity has led to the conclusion that the refiner may be unnecessarily particular when he selects one crude and rejects another. This preference, however, is very largely the reflection of the refiner's product demands and the quality of the stocks obtainable from the selected crude. The purpose of this paper is to point out critical characteristies of the major classes of refined products and to show how crudes vary in their suitability for such products. With relatively few exceptions, available processing methods and addition agents make it theoretically possible to produce any type of refined product from any crude source, although it may not be economically sound to do so. The widespread application of thermal cracking for converting higher boiling stocks into gasoline is well known. More recently cracking and refining in the presence of catalysts9 have been developed, as well as various processes for polymerizing lighter hydrocarbons into gasolines having desirable characteristics.6 For several years, selective solvents have been applied commercially to refining inferior quality kerosene, Diesel fuel and lubricating oil distillates.3 Improved methods for refining lubricating oils from crude residual4 formerly suitable only for fuel, are now in use and a number of special solvent processes are available for dewaxing lubricating oils to low pour point.5 These improved refining methods have been developed not only to meet the demand for improved product quality but also to enable the refiner to obtain quality products from crude sources that would not yield such products by the older refining methods. In many cases, the utilization of these modern refining tools necessitates an appreciable expenditure for equipment as well as added manufacturing costs, and their application therefore must be justified economically. Despite the availability of such tools, the added processing costs involved and yields obtainable may render their application entirely impractical. To illustrate this point, inspections of typical cuts from various crudes

Jan 1, 1940

By L. S. Darken

A quadratic formalism is developed lor the representation of the excess free energy, and of the activity coefficients of each component of a ternary system in the vicinity of a single component selected as solvent. This formalism, in contrast to the e formalism, is thermodynamically consistent at .finite concentrations. Numerous specific systems are used as illustrations, with cross checks where possible; these systems are Fe-C-X systems in the vicinity of 1600°C and include practically all those for which reliable data are available. It is shown that this formalism is usually quite adequate to rebresent available data up to a solute concentration of 20 to 30 at. pet. It is hoped that the formalism here presented may prove useful for the treatment and tabulation of data on ternary and multi-component solutions. SINCE, as discussed in a prior paper,' we do not as yet have an adequate basic understanding of the nature of binary metallic solutions, we cannot hope to be in better position for ternary and multicomponent systems. However, the accumulation of thermodynamic data on ternary and multicomponent metallic solutions has led to an urgent need for a rational formalism for the presentation and use of such data. Notable attempts to represent the isothermal isobaric thermodynamics of ternary solutions were made by Benedict et 01.' and by Wohl.3 These attempts were directed toward developing an analytic expression adequate to encompass the entire ternary triangle, primarily for organic systems; they generally involve the power-series approach, which has been shown' to be inappropriate, in general, even for binary metallic systems. On the other hand, interest in the thermodynamics of ternary and multicomponent metallic solutions has tended to focus either on general thermodynamic relations4-10 over wide compositional ranges, or on cases where one or more components have been at rather low concentration. This latter approach has been followed by Wagner,= by chipman,11 and by Alcock and Richardson,12 and more recently in many publications by the same and other authors. It has already been shown' that the thermodynamic behavior of binary metallic systems is, in general, relatively simple only in the terminal regions. Hence, it would appear that any approach, at this time, to a simple formalism for ternary and multicomponent systems must, a fortiori, be limited to the vicinity of the major component or solvent. The present treatment is aimed to be useful for a given solvent with moderate solute concentrations ranging up to 20 or 25 at. pet and in exceptional cases to considerably higher concentrations. In order to achieve even this modest objective, it is necessary that any appropriate formalism have built into it 1) a thermodynamic consistency (at least within the desired degree of approximation), and 2) an approach at infinite dilution to Raoult's law for the solvent and to Henry's law for each solute. Let us first formulate the condition of thermodynamic consistency for a ternary system. Under isothermal isobaric conditions, we may write for the molal value G of any extensive function dG - C1 dN1 + G2 dN2 + G3 dN3 [l] where the G's are the corresponding partial molal quantities and the N's are the atom fractions. Taking component 1 as the solvent, this relation may be rewritten in terms of the independent variables N2 and N3

Jan 1, 1968

ANDERSON, ALEXANDER, Captain, Royal Garrison Artillery. ANDERSON, GEORGE K., JR., Lieutenant, 30th Co., 3d Replacement Regiment. ARMSTEAD, H. H., Captain, Quartermaster Corps, U. S. N. A. ARMSTRONG, HAROLD KERR, Student Flight Officer, U. S. Naval Reserve Flying Corps, Dunwoody Naval Training Station, Minneapolis, Minn. BAKER, HARRY A., Captain, Co. M, 53d Pioneer Infantry. BASSETT, THOMAS E., Corporal, 340th. Field Artillery, Battery A, 89th Division, A. E. F. BATES, Wm.. T., 3d Reserve Officers' Training Camp. BAUMMGARTEN, K., 1st Lieutenant, 1st Corps School A. P. 0. 703. BAYLESS, G. E. S., Supply Dept., U. S. Submarine Base, New London, Conn. BENSEL, J. A., Major, U. S. R., Board of Control, War. Construction Activities, Norfolk, Va. BILLICK, DON C., Co. C, Ordnance. Supply School. BILLINGSLEY, PAUL, 1st Lieutenant, National Army, Statistics Branch,. General Staff. BLANDY, S. H. B., B. E. F.

Jan 8, 1918

By Edward H. Robie

PONCA CITY proved an ideal selection as a place of meeting for the Petroleum Division this fall. The accommodations at the Conoco Club were just what was required for such a gathering; the committee having the arrangements in charge functioned with the efficiency of veterans and the enthusiasm of neophytes; and the members and guests followed the speakers with close attention, entered the subsequent discussions with gusto, and divulged the "low-down" at private conferences. No one minded the drizzling rain on the first day, which only served to keep up the attendance in the auditorium; the weather then cleared up in time for a group picture before the gathering went their separate ways.

Jan 1, 1932

By H. J. Engell, W. Frank, A. Seeger

SWISHER and ~urkdogan' have determined the solubility of oxygen in a iron. They found it to lie between 7 and 10.5 at.-ppm at 881°C. Using earlier work on the permeability of oxygen in bcc iron,' they arrived at the following expression for the diffusion coefficient of oxygen in bcc iron (k = Boltzmann's constant, T = absolute temperature): where The present authors3 have estimated the activation energy QD for the diffusion of oxygen in bcc iron in two different ways from various experimental data.2'4"6 In the first method QD + QS (QS = heat of solution for oxygen in bcc iron in thermodynamic equilibrium with solid FeO) was determined either from data on the reduction of FeO with hydrogen4 or from measurements of the internal oxidation of silicon in a iron.5 Using an estimate of QS from investigations of the oxygen solubility in 6 iron2 (in thermodynamic equilibrium with molten FeO) Q = 0.97 ev or Q~ = 1.06 ev were obtained. From the magnitude of these values it was concluded that oxygen migrates interstitially in bcc iron and that consequently the activation energy QD for diffusion of oxygen has to be identified with the migration energy E~ of the oxygen atoms. Therefore, for a second estimate of QD from the diffusion coefficient of oxygen in 6 iron at 1450" ~,~ we used the theoretical expression:3 (a = length of elementary cube edge, m = mass of interstitially diffusing atom, sM = migration entropy), applicable to diffusion via the octahedral interstices in bcc lattices. Taking sM = 3.8 k (migration entropy of carbon in a iron), one gets Q = 0.90 ev. Hence, in Ref. 3 Q = (0.98 *0.1) ev was proposed as a plausible value for the diffusion energy of oxygen in bcc iron. sM + 9 (9 = solution entropy for oxygen in bcc iron) can be determined from permeability measurements.4 Using the above-mentioned estimate for QS , the following expression for the solubility c (atomic concentration) of oxygen (in thermodynamic equilibrium with solid FeO) in bcc iron was derived: From [4] the solubility of oxygen at 881°C in a iron is calculated to lie between 0.6 and 12 at.-ppm. We see that the solubility determined by Swisher and

Jan 1, 1969

By ALBERT F. J. BOARDEAUX

(Canal Zone Meeting, November. 191(j.) I. GENERAL INTRODUCTION. 1. Historical. ALLUVIAL gold was first discovered in Guiana in 1852, in the sands of the Arataye river; by Paulino, a Brazilian convict. During the following years, gold was found also in the rivers Orapu, Cirubé, etc. In 1873 the famous placers of the Sinnamary system were opened: Saint-Elie, Dieu-Merci, Adieu-Tat, and Couriége. This group of mines has produced nearly $10,000,000, according to official records, not including the gold that escaped the taxes. The discoverer was a mulatto named Vitalo. Except in a few rich spots, the gold was rather evenly distributed along the creeks. In one instance, gold was found in the red dirt from the slope of a hill, which, after transport to the creek, gave an amount of 150 kilograms. The placers of the Mana system, Enfin, Elysée, Pas-Trop-Tot, date from 1878, and their production has been about $5,000,000. In 1888, the Awa placers, along the boundary between the French and Dutch Guianas, on the Maroni and its tributaries, were discovered. They have yielded $12,000,000. The only industrial company,, the Dutch Guiana French Mining Co., produced in 15 years about 2,500 kg. of gold, worth $1,500,000. From 1893 dates the famous Carsewene discovery, in territory then in dispute between France and Brazil. A settlement was made recently in favor of Brazil, by arbitration of the Switzerland State Council. Carsewene is said to have pro-duced about $18,000,000 in six years (1894-1900), but not even one-fourth of the production went through French Guiana and

Nov 1, 1910

ALABAMA. Aldrich, Aldrich, W. F. Anniston, Noble, A. E Bessemer, Abbott, C. E., Fer¬gusson, V. Birmingham, Aldrich, T. H., Jr., Bowron, C. E., Bowron, J., Collord, G. L, Crockard, F. H., Davis, F. H, Dimmick, F. D., Hillman, Ludwig, C. P., McCarthy, M. E., McCormack, G B., McCrery, Ramsay, E., Shook, A. M. Car¬bon Hill, Pill, J. R. Coal City, Lydecker, I. S. Gannts Quarry, Hiller, E. Helena, Squire, J. Holt, Shook, J. \V. Huntsmlle, Moss. Lehigh, Toulmin. Oxmoor, Green¬amyer, A. G. Rock Run, Garvin, J. M. Sheffield, Miller, D. I. Woodward, Lodge, J., Woodward, A. H. ALASKA. Ellannar, Stevens, B. Fairbanks, Hamilton, A. L, Robe, L S. Hadley, John¬son, P. Jualin, Hoggatt, W. B. Juneau, Denby, Thane, B. L., Whipple, J. R. Katalla, Hampton, W. H. Ketchihan, Barber, J. C., Geiger, A. \V., Parker, J. L. Niblack, Finck, W. N., Niedling, B. B. Nome, Garfield, C. D. Tin Oity, Fay, A. H. Treadwell City, Kinzie, Stow, H. P. Valdez, Esterly, G. M., Hazelet.

Jan 1, 1910

By F. R. Cattoir, R. W. Kimball, C. T. Anderson

ONE of the principal impurities in all steels is sulphur. Sulphur-bearing, manganese-free steels exhibit hot shortness. Manganese is added to steel to improve the hot-working properties. If no sulphur were present in steel, it is probable that hot shortness would be nonexistent. This paper is the first of a series to be issued by this Laboratory reporting the measurements of hot forgeability tests and the physical properties of Fe-C alloys to which additions of various alloying elements have been made. The present paper describes the results- obtained by the addition of varying amounts of sulphur to Fe-C alloys. To obtain control over residual elements in the various charges melted in the arc furnace, it was considered advantageous to use sponge iron from one source as the melting stock rather than scrap metal having an unknown history. Small amounts of unwanted alloying elements might be introduced into the charge when scrap was used, thereby influencing the results of the various heats. A sponge iron having a high silica-lime ratio was used. Ore from Sunrise, Wyo., had been reduced to sponge iron and briquetted at the Bureau of Mines sponge-iron plant at Laramie, Wyo. The briquettes were 5 in. in diam and 2 to 3 in. in thickness, and weighed about 10 lb each. The chemical analysis of the sponge iron is as follows: C, 0.67 pct; Mn, 0.10; SiO2, 4.75; CaO, 1.4; P, 0.044; S, 0.72; MgO, 0.4; A12O3, 1.1; total Fe, 87.5; Fe metallic, 79.2; and reduction, 90.5 pct. Where a reducing agent was required, crushed graphite electrodes usually were used. The charcoal available contained 0.20 pct S. An analysis of the available coke showed it to contain 0.70 pct S. Where high sulphur heats were required, elemental sulphur additions were made to the ladle. Limestone of good quality was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2, 3.0; and P2O5, 0.014. Melting Procedure Sponge iron was melted to produce metal stock for the experimental alloys in a silica-lined, three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating. Fig. 1 shows this furnace installation. About 25 tons of sponge iron was melted in 75 heats, averaging 927 lb of sponge iron to the heat. An addition of carbon was required to complete the reduction of a portion of the iron oxide remaining in the sponge to prevent high losses of iron oxide in the slag and a low carbon content in the resulting metal. As reducing agents in preparing the melting stock, charcoal, coke, and a carbon product resulting from the thermal decomposition of natural gas were used. The quantity varied from 20 to 60 Ib per furnace charge, with an average of 38 lb. An average analysis of the metal obtained gave 0.52 pct C, about 0.01 pct Mn, 0.070 pct P, and 0.092 pct S. The average yield of metal was 647 lb with 241 1b of slag, the sponge-iron recovery being 70 pct. The metal obtained in melting the sponge iron was cast into pigs weighing about 20 lb each to facilitate recharging into the furnace for further refining. The pouring of the pigs is shown in Fig. 2. The average power consumption for the production of the 24 tons of metal obtained was 1704 kw-hr per ton.

Jan 1, 1954

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

Solid-solubility limits at 1500°, l000q and 500°C for carbon, nitrogen, and oxygen in high-purity tantalum were determined by X-ray lattice-parameter methods. For carbon, the solubility was found to be 0.17 at. pct at 1500°C, and less than 0.07 at. pct at 1000°C. A nitrogen solubility of 3.70 at. pct at 1500° C decreases linearly with temperature to 2.75 at. pct at 1000°C, and 1.8 at. pct at 500°C. In the case of oxygen, the solubility was found to be 3.65 at. pct at 1500°C, 2.95 at. pct at 1000°C, and 2.5 at. pct at 500°C. The phases Ta2C, the low-temperature modification of Ta205, and Ta,N of unknown composition but which has a superlattice structure based upon the original bcc tantalum lattice have been identified as the initial precipitates in the respective systems. Metallographic methods were employed to verify the X-ray analyses. The etching behavior of Ta is discussed in terms of lattice i?rzperfections and precipitate phases. The excellent fabricability, high melting point, and nuclear properties of tantalum are responsible for interest in this refractory metal. Data on the solid solubility of the interstitial elements (oxygen, nitrogen, and carbon) in tantalum and on the precipitate phases are somewhat limited. The significant contributions are discussed below. Because the purity of electron-beam melted tantalum (only recently available) is considerably higher than that used in previous studies, the present investigation was initiated. Gebhardt et all-3 have investigated the tantalum-oxygen and tantalum-nitrogen systems with particular reference to the changes in physical properties and to the rates of reaction between these gases and the metal. The solubility of oxygen in tantalum was reported2 to be 3.7 at. pet at 1500°, 2.3 at. pet at 100O°C, and 1.4 at. pct at 750°C. Schonberg4 reported that several oxide phases (Ta40, Ta,O, TaO and Ta,05) exist while X-ray studies by Gebhardtl showed only two oxides, Ta,05 and an unidentified phase which was associated with a platelet-type precipitate. La-gergren and Magneli,' however, questioned the existence of compounds other than the two allotropic modifications of Ta,05 for the tantalum-oxygen system. In the case of nitrogen, the solubility was estab- lished by Gebhardt3 to be of the order of 7 at. pct at 1800°c. The solubility was reported to decrease rapidly with temperature, and, although no limits were established, a precipitate phase was observed by Gebhardt except when the high-nitrogen specimens were cooled very rapidly from the reaction temperature of 1800c. He reported the initial precipitate phase to be a tetragonal distortion of the bcc tantalum lattice while Schonberg6 reported the phase lowest in nitrogen Jo be a cubic super-lattice with a cell size of 10.11 A. Two other nitride phases, Ta,N and TaN, were reported; these appear to be isomor-phous with the carbides of tantalum. The tantalum-carbon system was investigated by Ellinger7 and by Lesser and Braurer. Two compounds, Ta,C and TaC, were reported to exist, each with a range of composition. The solubility of carbon in tantalum was found to be practically nil at all temperatures. Thus, of the interstitial elements which are present in small amounts in high-purity tantalum, carbon might be expected to form precipitates. The present investigation was initiated to obtain additional data on the solid-solubility limits of these interstitials at 1500°, 1000°, and 500' with particular emphasis on the distribution and the identification of the precipitate phases. EXPERIMENTAL WORK AND RESULTS In the present investigations of the solid solubility and of the precipitate phases in the systems tantalum-nitrogen, -oxygen, and -carbon, high-purity tantalum was reacted with high-purity gases, homogenized at 1800°c, and annealed at and quenched from 1500°, 1000,

Jan 1, 1962