Search Documents

By ALBERT P. J. BORDEAUX

THIS paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver-ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold-ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there was a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. GENERAL OUTLINE OP THE CYANIDE TREATMENT. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By H. H. Podgurski, F. N. Davis

In silver alloys containing less than 0.2 wt pet Cu. the reaction 9 + 1/2 0, = CuO(s) was found to proceed to equilibrium between 700o and 808oC. From measurements of the equilibrium dissociation pressures of the CuO at several temperatures, the differential heat of solution and the activity coeflicients for copper in silver were calculated. These values were found to be in reasonable agreement with those calculated from data appearing in the literature. A metastable "copper oxide" with an atom ratio of oxygen to copper as high as 1.7 was formed by internal oxidation at 300°C of these same dilute Ag-Cu alloys. No anomalous behavior was noted in the temperature dependence of oxygen solubility in silver. The solubility minima between 300" and 800°C reported several years ago can be accounted for, at least in part, by reactions with trace impurities, such as copper. Cold-worked siloer exhibits an enhanced permeability to oxygen. THIS investigation was undertaken because of our interest in interactions between solute and lattice defects in metals. The reason for the choice of the O-Ag system for study is the anomaly in the solubility of oxygen in silver reported by Steacie and Johnson1 in 1926, specifically that isobars between 100 and 800 Torr show solubility minima at 400°C. It was also claimed that the copper impurity in the silver was not responsible for the minima. Recently, Eichenauer and Müller2 proposed that surface adsorption might have been responsible for this solubility anomaly, but no adsorption isotherms are available to check the pressure and temperature dependence observed at the low temperatures. Surface-tension measurements on silver made by Buttner, Funk, and udin3 suggest that a considerable fraction of a monolayer of oxygen exists on silver at 922°C and at an oxygen pressure of 150 Torr. To account for the pressure sensitivity reported by Steacie and Johnson1 at 300°C, the oxygen bound to the surface at 922°C cannot be considered relevant; the existence of a surface layer at 300°C characterized by a lower energy of binding would be required to explain the effect. All of our attempts to detect an interaction of this type with surface sites have failed. In this investigation we have not been able to associate the dissolution of oxygen in silver with a dislocation interaction. Evidently, severely cold-worked silver does not contain a sufficient number of trapping -sites for oxygen. Indeed, our work shows that oxidation of trace impurities in the silver was probably responsible for Steacie and Johnson's results. In addition, we have been able to establish the nature of the reaction with copper impurity in silver by thermodynamic considerations. EXPERIMENTAL PROCEDURE Measurements of both the internal oxidation rates and the solubility were made volumetric ally in a system equipped with a gas burette, a mercury manometer, a McLeod Gage, and a mass spectrometer. The silver and the silver-alloy samples were protected from contamination by mercury vapor from our pressure gages by suitably placed refrigerated (-78°C) traps. Silica reaction vessels were employed for experiments performed above 500°C. Spectroscopically pure gases were used in this investigation. The highest-purity silver used in the solubility measurements was 99.999 pet. By chemical analysis 2 ppm of Cu were found in this silver. The two Ag-Cu alloys used in this research were made up to 0.14 and 0.15 wt pet Cu starting with 99.999 pet Ag. An unexpected source of error was discovered in the course of the work. At temperatures near 800°C silver distilled from the hot silica reaction tubes into cooler regions of our system. Although the weight loss of silver from the sample was not important in itself, oxygen was being consumed by the silver distilled into the cooler part of the system to form a stable oxide phase from which the oxygen was not recovered. In a separate experiment conducted to determine the necessary correction, losses between 0.2 and 0.3 cu cm (stp) of 0, in 24 hr were measured at 810°C. On the assumption that the flux of silver from the vessel to form Ag2O de-

Jan 1, 1964

By C. H. Jr. Herty

THE removal of sulfur from steel has been studied by many investigators, but the quantitative relationships between the factors involved have not been determined. This is undoubtedly due to the number of variables encountered in practice, an attempt to study any one reaction or relation being affected by other reactions the relative importance of which cannot be estimated. The factors that affect the extent of removal of sulfur in the basic open-hearth process are generally considered to be: 1. Basicity of the slag: (a) Iron oxides in the slag; (b) carbon in the metal, or carbide in the slag; (c) temperature. These factors affect the reactions: FeS + CaO = CaS + FeO FeS + CaO + C = CaS + CO + Fe. 2. Amount of sulfur in the gas. 3. Amount of manganese in the metal. The factors which affect the rate of removal of sulfur include, in addition to these 4. Fluidity of the slag: (a) Normal changes in fluidity with temperature; (b) changes in fluidity because of the addition of special reagents such as fluorspar. 5. Agitation of the bath.

Jan 3, 1925

Jan 1, 1880

By PERCY E. BARBOUR

SECONDARY copper1 has &come more or less of a bugbear generally. What is its influence is often the subject of heated argument. The inedapable fact usually quoted is that since in 1929 primary production of copper in the United States was 1,026,348 tons and secondary production was 626,550 tons, there- fore, 0.6 lb. of secondary is produced for every pound of primary, and "How can you get around that?" The matter seems very plain, now that I have reached my conclusions, but they are the result of much laborious study and research. I shall show that' the production of secondary copper is not 0.6 per lb. of primary, in spite of statistical appearances; that the production of secondary is a function of primary production rather than of price; that secondary production has 'only a sub-. ordinate influence on the price of copper and then only in abnormal times; that there is not an accumulating reservoir of secondary from which the country is some- time to be drowned in copper, as is believed by some, or a reservoir from which we are going to draw much needed and more or less inexhaustible stores in the future, as is believed by others; and finally, that the United States always produces more copper than it uses and exports the surplus. These are all controversial points, and for that reason and to anticipate argument I have set forth my reasoning in considerable detail.

Jan 1, 1931

By E. E. AGGER, Arthur Notman

THE proposal has been made in a bill introduced into Congress at the last session by Representative Jones of Michigan that an import duty of 6 c. per lb. shall be placed on copper. This action is urged after eighty years of prosperity for the industry in this country; during most of which copper has been on the free list, and during all of which a tariff would have been without real effect. To comprehend the general situation upon which this action would be imposed, we must refer to the past history of the industry and its trends at the present time. The following table supplies us with a picture of the physical growth of the industry in this country and its relation to that of the world as a whole down to Jan. 1, 1921:

Jan 1, 1925

By C. F. Smart

The heat treatment of the bronze composed of 88 per cent. copper, 10 per cent. tin, and 2 per cent. zinc, has been investigated by H. S. and J. G. S. Primrose,' and also by the U. S. Bureau of Standards.2 The results obtained by H. S. and J. G. S. Primrose on dry-sand castings subjected to reheating followed by air cooling, or by quenching in water, are shown in Figs. 1 and 2. The values for tensile strength have been converted from tons per square inch to pounds per square inch. Figs. 3 and 4, have been plotted from values obtained by the Bureau of Standards on material of the same composition and treatment. Both investigations show that the ductility of the cast bronze is improved by heating to 700' C. and cooling in air, the strength not being impaired by this treatment. They are not in agreement, howevcr, as to the effect of quenching, Messrs. Primrose reporting a decrease, and the Bureau of Standards an increase, in both strength and ductility when the cast bronze is heated to 600' or 700' C. and quenched. The present investigation was undertaken to study the effect of annealing followed by different rates of cooling, and, in particular, the

Jan 1, 1921

By C. G. Dunn

This note describes a method for revealing micro-structures in tantalum through an {hkl} effect which was found during a study involving amorphous and crystalline tantalum oxides. Three steps are involved. First, an amorphous film of Ta2O5 is formed anodically1 on the surfaces of the tantalum. The amount needed depents on the thickness of the substrate tantalum; 1600Å of oxide, however, is generally satisfactory in the 1/2 -mil (12 µ) to 3-mil thickness range. The film at this point is uniform in color. Second, the anodized specimen is heated to 800°C in. vacuo during a period of a few minutes and held at temperature for 5 min. During such a treatment some oxygen leaves the oxide through dissolution into the substrate tantalum (e.g., at 10-8 Torr oxide films thinner than about 800 completely disappear on 5-mil strip). Considerable crystallization of the amorphous oxide also occurs adjacent to the metal/oxide interface but not throughout the oxide thickness. The thickness of oxide needed as a residue is not too critical; values between 500 and 1000Å (optical estimate') may be most useful. (The presence of a residual oxide layer after the heat treatment usually is not apparent; in fact, in most instances the surfaces have a metallic appearance. This can be the case also for thicker residual films needed in the detection of a crystalline oxide phase by surface X-ray diffraction—e.g., if the initial oxide film is 3000Å thick, enough crystalline oxide is formed for X-ray detection.) The third step eliminates the metallic appearance at the surface and reveals (or produces) a varied colored film of tantalum oxide. Two methods can be used and both will be illustrated. If the specimen is dipped in 48 pct HF for a few seconds, the tantalum is found to be covered with a multicolored oxide. Moreover the colors correlate with the grain structure of the substrate tantalum through an orientation dependence of the type illustrated in Fig. 1, where results of an orientation analysis by the Laue X-ray method have been plotted. Other film conditions would have provided a different set of colors for the same orientations. Any such correlation, however, provides a basis for a qualitative assessment of the distribution of orientations in a large sample. The cold-rolled structure of tantalum foil produced by a recrystallization anneal and a cold-rolling reduction of 95 pct is not easily obtained by usual metal-lographic methods.' The structure, however, is easily revealed by the present technique, Fig. 2. The alternative third step is to reanodize the specimen. The optical nature of the final anodic film depends on the presence of the crystalline oxide phase; color variations indicate optical thickness variations in the film. As the reanodization voltage is increased from zero, straw and light brown colors appear (as usual), followed now by variations in color from grain to grain depending on {hkl} orientation. Suitable end points, which are determined by voltage and time, are easily established. Fig. 3, for example, shows the grain structure developed in 5-mil tantalum strip during a 30-min re-crystallization and grap-growth anneal at 1800°C. An anodic film of 1600Å thickness was added prior to the special 800°C anneal. Reanodization was done at constant current density (near 0.2 ma per sq cm) in an aqueous solution of H3PO4 (0.01 pct) and was terminated after the initial brown colors were replaced by a deep blue at approximately 30 v. Although good grain contrast can be obtained with bright field illumination, even greater contrast for black and white micrographs may be obtained with polarized light, as in Fig. 3.

Jan 1, 1967

By J. H. Hamilton, J. R. Lewis, J. H. Dismant, W. M. Fassell

RECENTLY this laboratory undertook the task of preparing some low carbon metallic cobalt by the carbon reduction of precipitated cobalt oxides. The oxides came in two lots and had the compositions given in Table I. Industrially, cobalt rondels' are made by the carbon reduction of cobalt oxide in small reverberatory furnaces at temperatures near but not above 1050 °C. This is a slow and tedious small batch process but does give cobalt metal which is low in carbon (1 pct C). Inasmuch as these cobalt oxides were relatively low in copper and iron it was decided to reduce them with petroleum carbon in a small three-phase electric arc furnace of about 3 to 5 Ib of metal capacity. It was hoped such a procedure would save considerable time and perhaps also indicate an improved commercially feasible process. The furnace was preheated by using small pieces of carbon electrodes to maintain the arc until a temperature of 1500°C was reached. The broken pieces of electrodes were then removed and 500 g of the cobalt oxides and 60 to 100 g of petroleum coke added. At the end of the reduction reaction, a high lime flux was added to the furnace to facilitate the removal of sulphur. Due to the fineness of the cobalt oxide powder used and also to the presence of chlorides there was considerable dust lost in charging the furnace. This was overcome by preparing briquettes composed of the cobalt oxides, charcoal, and a little bentonite to serve as a binder. The results obtained are summarized in Table 11, which shows that the cobalt metal produced in the arc furnace was high in carbon varying from 2.5 to 3.5 pct. This, of course, is much too high. For certain uses, such as in the preparation of permanent magnets, the carbon content of cobalt must be low. It was necessary therefore to find an effective method of reducing the carbon content of the cobalt that had been prepared in the arc furnace. Van Arkel3 recommends the use of Co2O3 as a means of removing carbon from cobalt. Experiments by the authors indicate that carbon is removed with difficulty by this method. Other methods used, including lancing of the molten high carbon cobalt with a jet of oxygen, proved to be ineffective. The method finally used makes use of the fact that cobalt metal is decarburized by carbon dioxide at the temperature of the molten metal. Two methods were used: 1—carbon dioxide was bubbled up through the molten cobalt, and 2— molten cobalt was maintained in a carbon dioxide atmosphere. In the first method the gas was introduced below the surface of the molten metal by means of a quartz tube. A high frequency induction furnace was used to keep the cobalt molten in both of these experiments. This kept the metal somewhat agitated and no doubt was an important factor in hastening the decarburization 'process by the second method. Both methods gave satisfactory results as shown in Table 111. An interesting observation in connection with this 'work was that a small sample of carburized cobalt metal could be decarburized by heating it with an acetylene torch adjusted to give an oxidizing flame. This may have been due to the presence of carbon dioxide in the products of combustion. Samples of molten high carbon steel were decarburized by the same method and it is suggested that nickel and perhaps manganese can be decarburized in a similar manner. Additional work, including rate studies and other theoretical aspects of this problem, is in progress in this laboratory.

Jan 1, 1953

By Robert H. Leach, C. H. Chatfield

This paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in conlmercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordaq4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. Analysis of Steeling Silver Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same ana,lysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry I1 in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

By E. Miller, J. M. Eldridge, K. L. Komarek

Aclivilies of magnesium in liquid Alg-Si alloys have been delermined between 5 and 60 at. pcl Si, close to the melling point of Mg2Si, by an improved isopieslic melhod. Silicon specinrens, held in alumina crucibles and graplrile conlainevs of special design, were healed in a letrlpevalure gvadient and equilibrated with mag-nesilcrrl rapor in a closed lilanium system. The ther-madynamic Junctions were calculated and compared with the thermodyuamic properties of the other three mg- Gvoup IVB systems. Lattice paramelers of three Mg2X compounds were measured. The bonding in the Mg2X compounds is largely covalent with small and uarying amounts of metallic and ionic conlvibutions. The Mg-Si phase diagram1 has one congruent melting compound, Mg2Si, of essentially stoichiometric composition, two eutectics, and very limited terminal solid solubilities. Little information is available on the thermodynamic properties of this system. The free energy of formation of Mg2Si has been determined by the Knudsen cell technique2 in the range 572" to 680oC, by the transportation method3 between 858" and 950oC, and by the electromotive-force method4 in the range 400o to 600°C. Kubaschewski and villa5 and caulfield6 have measured the heat of formation of Mg2Si. An electromotive-force study of magnesium-rich liquid alloys was recently published by Sryvalin el al.7 The present investigation was undertaken to complete a general survey of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,a9,Mg-Sn,10,11 mg-Ge,12and Mg-Si. An isopiestic technique, previously developed for similar measurements on liquid Mg-sn11 and Mg-Ge alloys,12 was modified for the Mg-Si system. Specimens of the nonvolatile component, silicon, were contained in dense alumina crucibles placed inside covered graphite crucibles which were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure. The alumina crucibles prevented contact between the highly corrosive liquid Mg-Si alloys and graphite. The graphite cruci- bles effectively preserved the high-temperature equilibrium composition of the liquid alloys containing highly volatile magnesium on termination of the experiments during the quench to room temperature. EXPERIMENTAL PROCEDURE Silicon of semiconductor-grade purity (E. I. du Pont de Nemours and Co., Brevard, N.C.) and 99.99+ pct Mg (Dominion Magnesium Ltd., Toronto, Canada) were used. Graphite crucibles with press-fitted lids were machined from high-density (1.92 g per cu cm) rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The alumina crucibles had a purity of 99.7+ pct (Triangle RR grade, Morganite, Inc., Long Island City, N.Y.). In preliminary runs the liquid alloys were contained in graphite crucibles following the exact procedure developed for the Mg-Ge system.'2 These runs failed due to appreciable reaction between the molten Mg-Si alloys and graphite, and the results have been discarded. The procedure was then modified and the Mg-Si alloys were subsequently held in alumina crucibles. For most of the runs alumina crucibles of known weight and approximately 6.3 mm ID, 12.5 mm height, 1.0 mm wall thickness were loaded with weighed amounts of silicon and encapsuled in tightly covered weighed graphite crucibles 5/16 in. ID, 2 in. helght, 3/32 in. wall thickness). The graphite crucibles were machined from rods which were 85 pct of the theoretical density. These crucibles were therefore sufficiently porous so as to permit magnesium vapor to effuse through the silicon under the experimental conditions of approximately 970O to 1220°C and 1 day equilibration time. However, negligible magnesium was lost from the crucible during the quench due to the slow effusion rate through the pores of the graphite. The inner alumina crucible prevented the liquid alloys from contacting the graphite, and the very tightly fitting graphite crucible lids served to retain any magnesium vaporizing from the alloys inside the crucibles during the quenching step.12 The loaded silicon-alumina-graphite cells were positioned, one above another, on a 16-in.-long titanium thermocouple well and tied securely to the titanium tube with thin molybdenum wires held in grooves around the circumference of the graphite crucibles. A thin (0.005-in.) molybdenum strip prevented contact between the graphite crucibles and the titanium. This assembly was lowered into a titanium reaction tube (la in. ID, 16 in. long, $ in. wall thickness) closed on one end which contained a 11/2-in.-long cylinder of magnesium at the bottom. The inner titanium thermocouple well was positioned eccentrically in the large tube because of the eccentric mounting of the cells on the well. Appropriate modifications of the titanium cap"'12 were made to join the inner and outer titanium

Jan 1, 1968

By Donald H. McLaughlin

THE activity and enthusiasm of pioneers still prevail among workers in applied geophysics1.- Within the year, new devices have .been tried out, instruments and technique have been improved and the methods of application to commercial problems have been increased in many ingenious ways. There is still great need for more skillful interpretation of results in terms of geology, but oil the whole geophysical prospecting is making encouraging progress toward finding its proper place and function in engineering and geological practice. Spectacular successes continue to be reported, particularly .from the Gulf Coast, where the race for salt domes has not slackened, and encouraging results have been giined elsewhere in the mapping of structures in the search for oil. In the mining field, however, it can hardly be claimed that the same measure of success has been obtained, for brilliant efforts worthy of wide recognition have been overshadowed to some eatent by the unfortunate outcome of surveys undertaken unwisely without recognition of the limitations of the work. Consequently, hopes were aroused that could not be fulfilled, and it must be admitted in an impartial survey that there are a few regions, chiefly in the far north, where the standing of geophysical prospecting is somewhat doubtful and where the course of public opinion regarding it shows a certain similarity to the history of the market during the past few months. Reliable work, however, is steadily going 011 and it can confidently be expected that the methods will eventually be regarded in many regions as an essential part of the technique of securing geologic data needed for intelligent exploration.

Jan 1, 1930

By Richard W. Smith

Why are we losing our liberties? (1) . . . because our local chambers of commerce come to the National Chamber's annual meeting, vote for a policy on federal economy, and then go to Capitol Hill and ask for a federal project for their area. (2) ... because our mining men ask for a subsidy to mine submarginal deposits that can't be economically mined in a free economy. (3) . . . because 18,000 men and organizations all over the country recently wired or wrote a Congressional committee asking that the Army Engineers be exempt from the President's power to reorganize the Executive Branch of the government under the recommendations of the Hoover Commission.

Jan 1, 1949

By Eugene Stephenson

IN most instances the fluids produced from underground reservoirs have been described as they appear at the surface, and usually it has not been necessary to distinguish between surface and reservoir phases. More recently it has become imperative to recognize the fact that changes in phase may occur between the reservoir and the receiving unit. The simple terminology of "wet" and "dry" gases and "crude petro-leum oil" served our needs fairly well in the shallow, low-temperature and low-pressure fields. It has been left to the legislatures, regulatory com-missions, and courts to decide whether a field is or was a gas field, an oil field, or both. This they have done by direct definition and also by implication. For example, in Texas:1 (d) The term "gas well" is any well (a) which produces natural gas not associated or blended with crude petroleum oil at the time of production, or (b) which produces more than one hundred thousand (100,000) cubic feet of natural, gas to each barrel of crude petroleum oil from the same producing horizon, or (c) which produces natural gas from a formation or producing horizon productive of gas only encountered in a well bore through which crude petroleum oil is also produced through the inside of another string of casing. (e) The term "oil well" is any well which produces one (1) barrel or more of crude petroleum oil to each one hundred thousand (100,000) cubic feet of natural gas.

Jan 1, 1938

By Robert H. Leach, C. H. Chatfield

THIS paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in commercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordan,4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. ANALYSIS OF STERLING SILVER Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same analysis as our sterling. The first authentic record of the establishment of a stand¬ard alloy is during the reign of Henry II in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

Jan 1, 1928

By Johnson Crawford, Alan H. Hoagland

Zinc mining at Jefferson City began in 1854 with small scale production of oxidized ore from open pits. Significant production began in 1913 with the development of the Mascot Mine by the American Zinc Company. In 1965, four flotation mills were treating crude ore at the rate of about 12,000 tons per day and the Mascot-Jefferson City district currently is the largest zinc producing area in the United States. The producing mines, Mascot, Young, North Friends Station, New Market Zinc, Grasselli, Davis-Bible, Coy, and the Jefferson City, are 15 to 28 miles northeast of Knoxville in the Valley and Ridge physiographic province, an area of gentle relief lying between the more rugged Great Smoky Mountains and the Cumberland escarpment. The ore is strata bound, occurring essentially within a stratigraphic range of 200 feet in the Lower Kingsport and Upper Longview formations of Lower Ordovician age. In the lower strata of the mineralized section, the ore generally is found in coarsely crystalline elastic dolomite breccia containing silica and chert debris within a sequence of aphanitic limestones. The upper strata of the mineralized section are fine-grained primary dolomites that, in the ore zones, have been fragmented in mosaic patterns by solution collapse with the interfragmental space filled by white gangue dolomite and sphalerite. The mineralogy is unusually simple, sphalerite being the only important sulfide. Pyrite is very sparse. Dolomite gangue is abundant, silica was deposited in quite small amounts, calcite is minor, and fluorite and barite are very rare. The principal ore controlling structures are rubble breccia zones that were formed during the post-Lower Ordovician-pre-Middle Ordovician erosion interval by supergene solution as a phase of the development of a regional karst system of underground drainage that extended to' depths of at least 800 feet. The major Appalachian orogenic structures are post-ore and have been superimposed on the ore bodies. There is substantial evidence to support the current thinking of the writers that the ore deposits were formed at a depth not exc1~eding 800 feet.

Jan 1, 1968

THE solid nonmetallic inclusions present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general, the term non-metallic inclusions seems to be satisfactory and adequate. NATURE AND CONS1lTUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those occurring as a result of reactions taking place in the body of molten or solidifying metal and (2) those resulting from mechanical incorporation of refractories or other materials with which molten steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag-stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulfides but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from molten or solidifying steel may be caused by: (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change

Jan 1, 1964

By Dudley L. Davis, E. C. Peterson

INTRODUCTION THE Darwin District is 30 miles east of Olancha which is 220 miles north from Los Angeles via U. S. Highway No. 6. The ore deposits occur in the Darwin hills that have been elevated above the Darwin Plateau by typical basin and range-type faults. Some of these faults have been active quite recently as shown by the displacement of Quaternary (?) basalt flows and the rejuvenation of erosion in Darwin wash. The ore bodies occur as fissure fillings and replacement of favorable beddings in a thick series of Paleozoic limestones, dolomites, shales and quartzites. Rich oxidized lead-silver ores were discovered in the early seventies. By 1875, Darwin had a population of about 5000, and by 1880 several small mills and smelters had been built. Early exhaustion of surface ores, the isolated location of the district, and fluctuation of metal prices caused intermittent operations until World War II. The district production is estimated at about $3,000,000 prior to 1900 and perhaps $4,000,000 between 1900 and 1945 when Anaconda purchased the major producing mines. For the past two years, daily production has averaged 75 tons of direct shipping and 150 tons of milling-grade ore. At present, 300 tons of mixed oxide and sulphide ore are treated by flotation, the oxidized lead minerals being activated by addition of sodium sulphide after galena and sphalerite have been recovered from the circuit. Extraction averages 85 pct of the lead, 80 pct of the silver, and about 33 pct of the zinc in a bulk concentrate. The mill is designed so that minor changes permit selective flotation of pyritic lead-zinc ores encountered at depth. GENERAL GEOLOGY The oldest rocks in the Darwin hills are a series of Paleozoic limestones, dolomites, shales and quartzites probably Pennsylvanian in age. These rocks have been intruded on the west by the Coso granite batholith and on the east by a granodiorite stock. Numerous sills and dikes grading from orthoclase granite to gabbro are exposed in the underground workings. The sedimentary rocks have been considerably folded and faulted, the most prominent structure being a northwest pitching anticlinal fold, the crest of which lies just west of the ridge line of the Darwin hills. The east limb of this fold has been intruded by the granodiorite stock and east of the stock the sediments show several closely spaced anticlines and synclines. The minor flexures on the west flank of the major fold are structurally important in localizing the ore in the Defiance and Essex mines of the Darwin group. There are three principal systems of faulting and fissuring, most of which are post-intrusive and premineral in age, with minor amounts of postmineral movement. The Darwin tear fault is the largest, most persistent fault in the district. It strikes N 60 to 95°W, dips steeply south and is traceable for about 1o miles. It is a normal

Jan 1, 1947

THE opening session was held on Tuesday evening, February 17th, in the house of the American Society of Civil Engineers. The President of the Institute, Mr. E. B. Coxe, after a few introductory remarks, congratulating the members on the general prosperity in all the branches of the professions and manufactures represented by the Institute, called on Mr. E. F. Loiseau, of Philadelphia, for the first paper, On the Successful Manufacture of Compressed Fuel at Port Richmond, Philadelphia. Professor Prime called attention to the fact that the work of the United States Testing Board had been left unfinished at a point when valuable results had just been reached, and offered the following resolutions: WHEREAS, The American Institute of Mining Engineers has seen with regret that the work of the United States Testing Board has been suspended through the lack of an appropriation by Congress, which appropriation dues not seem likely to be renewed, and WHEREAS, It seems most important to the vital interests of our iron and steel manufactures that the experiments commenced by the United States Testing Board should be carried to successful completion ; Resolved, That a committee of three be appointed, to act with a like, committee to he appointed by the American Society of Civil Engineers, to carry out to completion the work commenced by the United States Testing Board. Resolved, That the American Society of Civil Engineers be requested to cooperate with this society by the appointment of a like committee. Resolved, That the committee have authority to request, in the name of the American Institute of Mining Engineers, contributions to a fund to be devoted to the completion of the experiments aforesaid. Resolved, That the Council of this Institute be authorized, whenever requested by the committee so appointed, to petition Congress for the free use of the testing machine at the United States Arsenal at Watertown. Resolved, That a committee be appointed by the President, to select the afore-said committee of experts. Resolved, That the President of the Institute have authority to fill any vacancies which may occur in the committee. The resolutions were unanimously adopted, and President Coxe appointed the following committee in accordance with the resolutions : Messrs. A. L. Holley, James Park, Jr., and J. F. Holloway. The President also appointed Messrs. Heinrich, Mickley, and Spils-

Jan 1, 1880

By J. O. Brittain, N. R. Adsit

A number of zinc bicrystal specimens with the grain boundary loaded in simple shear were plustically deformed in creep in a vacuum at 200°C and under an argon atmosphere at 350°C. The results indicated that the amount of grain boundary sliding at a given time was controlled by the slip in the grains and was proportional to the resolved shear stress on the slip plane. Curves of grain boundary sliding vs time were found to be cyclic with no regular periodicity. ALTHOUGH grain boundary sliding (G.B.S.) has been investigated in a number of different types of tests on various materials there is substantial disagreement on the interpretation of the various observations. Gifkins1 has presented a comprehensive review of the subject of G.B.S. and fracture. He reports that the activation energy for high-temperature creep is equal to that for volume self-diffusion and that pure metals show less tendency towards intercrystalline fracture than alloys. Pure metals show appreciably greater grain boundary migration than alloys, and both grain boundary migration and grain boundary sliding follow the same general trend in time as plastic deformation during creep.' While there have been a number of different mechanisms proposed to account for G.B.S., none of the models explains all the results. Since zinc has only one prominent slip system, it was hoped that experiments on G.B.S. in zinc bicrystals might enable us to separate the effect of grain boundary angle and the effect of matrix slip and thereby resolve at least one part of this complex phenomenon. EXPERIMENTAL PROCEDURE Bicrystals of pure zinc (99.99 pct) were grown by a Bridgeman technique in a furnace having a gradient of 20°C per in. The bicrystals were seeded to a desired orientation and grown in a split graphite mold which was 3/4 by 5/8 by 8 in. The mold was enclosed in a Pyrex tube and the tube was evacuated and then filled with a small amount of argon before it was placed in the furnace. The growth rates were 1/2 to I in. per hr for the bicrystals and 1/2 to 3 in. per hr for the single-crystal seeds. The longitudinal V notches served to hold the grain boundary in position during the growth process. A schematic rep- resentation of a specimen which had been cut with a jewelers saw from the bicrystals is shown in Fig. 1. All specimens of a series were cut from the same crystal, some of which were 7 in. in length. After specimen preparation the boundary was approximately 5/16 in. long and the V notches had a radius of 1/16 in. The boundaries were straight at a magnification of X100 with the exception of a few which had a gradual radius of curvature of greater than 3.2 in.-1. Laue back-reflection photograms were taken on the specimens to check the orientation of grains in the bicrystals. The method of relating the orientation of the two lattices is shown in Fig. 1, where 0 is the angle between normal to the boundary and the trace of the basal plane, is the angle in the boundary between the trace of the basal plane and a line parallel to the V notch, and x is the angle in the basal plane between the Burgers vector and the perpendicular to the grain boundary. After mechanical polishing the specimens were chemically polished.2 Subsequent to the polishing operation the specimens were encapsuled under a vacuum of better than 25 annealed at 340°C for 1 hr to remove the effects of this handling, and again chemically polished. Finally, fiduciary marks were scribed on the specimen using a micromanipulator. Creep tests, which were conducted in a modified Bausch apparatusS with the boundary loaded in simple shear, were run at a constant load (since the boundary area remained essentially constant this is approximately constant grain boundary stress). The temperature was controlled to ±1/4°C as measured on a semiprecision potentiometer with a calibrated thermocouple. The specimens were tested in a vacuum of better than 0.5 at 200°C and in purified argon at a pressure of 1/2 atm at 350°C. The op-

Jan 1, 1965