Search Documents

By C. S. Smith, K. K. Ikeuye

In an earlier paper1 one of the authors called attention to the significance of the relative free energies of grain boundaries and interphase boundaries in alloys in determining the shape and distribution of micro-constituents. The ratio of the interphase and inter-crystalline boundary energies (that is, —?12, where ?12 is the energy of the interface between a crystal of phase 1 and a crystal of phase 2, and ?11 is the energy of the boundary between two crystals of phase 1) will be denoted by F. It is this ratio that determines, by the simple triangle of forces relation, the dihedral angle, ?, of phase 2 where it adjoins a boundary between two grains of phase 1. On a metallographic sample various angles are actually obtained because of the random orientation of the plane of observation, but the statistically most frequent angle is the true one. These basic principles were discussed in detail in the earlier paper. The experiments described below show the effect of both composition and temperature on ? and T for some alloys containing a liquid phase, and provide data on the rate of approach to the equilibrium angles in both solid and liquid phases. All the alloys were melted in a graphite crucible and cast into ingots 3/4 by 11/8 in. cross-section. Some of the aluminum alloys consisted of two immiscible liquids from which uniform castings could not be obtained. The amount of liquid phase varied locally to a considerable extent and the analyses were meaningless. Nevertheless, the composition of the liquid would not differ from that in an alloy of the intended gross composition, and the synthetic composition of the alloys was therefore used in considering the surface energy results. The ingots were given initial deformation by cold-rolling to 50 pct reduction, annealed, and given a second 50 pct reduction prior to cutting into small samples for heat treatment at the times and temperatures subsequently reported. The resulting micro-samples were carefully prepared metallographically and examined at magnifications of 650, 1280, or 2500. The objectives used were 21X, 0.40 NA (dry); 41X, 0.65 NA (dry); and 80X, 1.40 NA (oil emulsion). The appropriate angles were measured by rotation of the stage of a Bausch and Lomb metallograph to align the appropriate boundaries successively with a cross-hair in a micrometer eyepiece. About 250 angles were measured on each phase. Though the angles were read to 1°, the accuracy is probably not above 3°, because of uncertainty in setting the cross-hair tangent to the sometimes curved boundary. The corners of very small particles, particularly in early stages of adjustment after cold-rolling, were difficult to measure and the results were slightly dependent on the magnification used (compare Fig 1-C and 1-D). With particles of larger size and more nearly equilibrium shape, magnification made no difference (vide Fig 1-F and 1-G). The measured angles were grouped in 10° intervals (5° if ? was less than 20°) and plotted in bar

Jan 1, 1950

By Samuel Wyer

F. G. CLAPP, New York, N. Y. (communication to the Secretary*).¬I assume that where this valuable paper states, near its end, that "it is not possible to establish a market price, " the author means that no particular price which will fit all conditions and fields can be given. I am not in agreement with Mr. Wyer, however, that the actual value of natural gas leaseholds is "largely a matter of opinion." I would even be willing to express myself very strongly as believing that if we, as experts, cannot give anything closer than a mere opinion, our testimony or reports are not of great value to our clients. I believe, moreover, that by detailed geological examinations and with our latest knowledge of geological structure, principles of natural gas occurrence, etc., we can approach just as near a certainty in natural gas valuations as we can in oil valuations, and much more so than in the valuation of many metal prospects, in which only the upper few feet of the vein has been opened. In other words, we are getting nearer and nearer every year to bringing geology as applied to oil and gas development into the class of an exact science. Mr. Wyer's paper gives an excellent outline for methods of leasehold valuation. Being presumably intended as an outline only, it can be expanded indefinitely by a detailed discussion of the methods of valuation for the four different classes of leaseholds which he mentions: (A) "Producing;" (B) "Protective;" (C) "Reserve;" and (D) "Prospective." This classification is probably as good as can be made in practice. In the producing leaseholds in particular it is easy to establish a market price at which these leaseholds should be bought or sold. The question would arise in any case whether or not the leases are connected with a pipe line or the distance from the pipe line. Assuming that a pipe line already taps the property and that gas is already being sold for a certain figure, this price must be multiplied by the number of thousand cubic feet still "in sight" in the ground, from which is to be deducted (a) bonuses, (b) rentals, (c) royalties, (d) cost of drilling, (e) taxes and

Jan 12, 1916

By K. Takahashi, I. Iwasaki

The methyl stretching vibrations for a series of normal xanthates, isoxanthates and normal amines were determined with the aid of an infrared spectro-photometer, and the results were compared with published information on the corresponding alcohols. The frequency shifts of methyl stretching vibrations may be attributed to the inductive effect of polar groups. The hydrogens in the shorter chain alkyl groups are somewhat polar and can be expected to interact with water molecules by hydrogen bonding. Contact angle, surface tension lowering, solubility, and critical micelle concentration appear to be related to the induced polarity of the alkyl groups. Traube's rule states that in homologous series of compounds solubility decreases and surface activity increases regularly with the size of the hydrocarbon group. Analyzing the work of transfer of a solute from solution to surface, Langmuir' interpreted this rule to mean that each CH2 group added to a molecule produced its effect independently of the others. It is also well known2 that the maximum equilibrium contact angle with sulfhydryl collectors is independent of the polar groups and of the sulfide minerals, and that it increases to a certain limit with the number of carbon atoms in the alkyl group. This observation is thought to demonstrate the orientation of the collector molecules at the sulfide surfaces. The dependence on the hydrocarbon chain length is usually explained as due to the screening of the force field of polar mineral surfaces.3-5 Here again, Langmuir's principle of independent surface action appears to be implied. Heteropolar compounds consist of nonpolar and polar groups, the former being the hydrocarbon group and the latter containing such electronegative atoms as O, N, S, P, or halogens. According to Palit6 the hydrogens in the alkyl groups are more electroposi- tive than in the paraffins owing to the negative inductive effect of the polar groups and a possibility that a hydrogen bond with water molecules ensues. Goto and Takenaka7 provided direct evidence of the inductive effect by measuring the shift of the C-H stretching vibrations of alcohols, acids, and alkyl bromides with an infrared spectrophotometer. Their approach appeared to be directly applicable to the studies of surface activity both at air-water and water-mineral interfaces encountered in flotation systems. The present article attempts to relate the C-H stretching vibrations of alkyl xanthates, alcohols, and amines with such flotation chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration. MATERIALS AND METHODS Normal xanthates from methyl to octyl inclusive and the isopropyl, isobutyl, and isoamyl xanthates used in this investigation were prepared in the usual manner.8 Normal amine hydrochlorides with carbon chain lengths of 1, 2, 4, and 6 were from Distillation Products Industries, of 8 from Archer-Daniels-Midland Co., and of 10, 12, 14 and 16 from Armour and Co. Normal propylamines, pentylamines and heptylamines from Distillation Products Industries were used both as received and as hydrochloride formed by converting the amines according to the procedure described by Li9 Perkin-Elmer Model 521 and 621 infrared spectro-photometers were used to investigate the spectra in the frequency region of 3050 to 2800 cm-' with frequency scale expansion. The accuracy of the frequency readings was within + 1 cm-1. The KBr micropellet technique was used to prepare the xan-thate samples for measurements, and the halocarbon mull technique was used for amines and amine hydrochlorides. EXPERIMENTAL RESULTS Fig. 1 shows the CH3 asymmetric stretching vibrations as a function of the number of carbons in the alkyl group for normal xanthates, isoxanthates and amines. Also included in the figure are data for normal alcohols and isoalcohols taken from the article

Jan 1, 1970

By A. Styka, G. Fischer, S. Tour

Described herein are the results obtained during research work involving coating titanium alloys with molybdenum by vapor-deposition methods. Results show that the method can be used successfully to deposit hard adherent wear-resistant coating of methodmetallic molybdenum on titanium or titanium alloys without changing the microstructure of the titanium base. PRODUCTION and use of titanium and its alloys have increased tremendously in the past few years. The physical, mechanical, and chemical properties of this engineering metal have caused considerable enthusiasm among metallurgists and engineers. However, as with all materials, there are some drawbacks. For example, titanium is susceptible to seizing and galling on wearing surfaces. In order to produce a good wear-resistant surface, many investigations have been conducted evaluating oxidizing, carburizing, nitriding, carbonitriding, sili-conizing, and chromizing of titanium. All of these processes require high temperatures for rather extensive periods of time. It has been possible to produce hard surfaces on titanium and its alloys by a number of these processes at the expense of a deterioration of the physical properties of the base material. A practical solution to the problem of providing titanium and titanium alloy parts with a satisfactory wear-resistant nongalling surface must be one that does not involve excessive temperatures for long periods of time. Sam Tour & Co. Inc. has completed a research and development contract for the United States Army Ordnance Corps on vapor deposition of molybdenum on titanium and titanium alloys. On the basis of results obtained from the research program, titanium alloys can be coated successfully with molybdenum to provide a hard wear-resistant surface without harm to their base mechanical properties. The remainder of this article is a description of the techniques used to apply the coating and the results obtained from wear tests on molybdenum-coated titanium. Theory Basically, the technique used was the application of molybdenum by a vapor-deposition method, thermal decomposition of molybdenum hexacarbonyl [Mo(CO)] with hydrogen as the carrier gas. The selection of this method was based chiefly on the following considerations: 1—low plating temperature which would minimize excessive grain growth, 2— low decomposition temperature of the carbonyl, 3— possibilities of controlling the hardness of the plate by adjusting the carbon content using the plating temperature and pressure as the primary variables, 4—use of high vacuum, thereby avoiding unnecessary oxidation and other complex reactions with the atmosphere. Free energy data1 show the strong tendency for titanium to combine with O2 N2 or carbon from normal temperatures to temperatures above its melting point. To maintain the titanium in a film free condition, the use of as high a vacuum as possible is indicated. The literature' indicates that the reaction product of hydrogen with titanium is unstable in vacuum at around 400°C. 5—Although it is indicated from the thermodynamic standpoint that there is little possibility of removing carbon from either titanium or molybdenum, the work of Lander and Germer -ndicates that the use of a suitable H,/CO ratio is somewhat effective in minimizing carbon deposition. 6—Availability of molybdenum carbonyl. In the simplest form, the conditions of equilibrium3 in chemical reactions involving decomposition of carbonyl are as follows: Mo (CO) ? Mo + 6CO 2CO * C + CO,. The plating rate is proportional to the rate of evolution of CO from the decomposed carbonyl, i.e., it is proportional to the pressure of the gaseous decomposition products. Carbon released from CO gas is the significant constituent for the variability of the physical properties of the product. High carbon deposition is favored by increasing pressure. Limitations are imposed in the selection of plating temperature and pressure. Excessive temperature re-

Jan 1, 1956

By I. S. Levy, J. L. Brimhall, B. Mastel

Specimens of' Hastelloy X-280, a low-cobalt version of the solid-solution- hardened nickel-base alloy Hastelloy X, were given a series of thermomechanical treatttzents. They were then Lensile-tested at room temperature and 1350°F. The Microstructures of the specimens tested at 1350°F were studied by electron Microscopy. Microscopy showed that dislocation tangling, caused by the cold working, mas still in evidence after aging-for 24 hr to temperatures as high as 1550oF. (Cr, Mo)23 C6, (Fe, Mo)6 C'. as well us an unidentifiable phase precipitale due to the combination of the thermomechanical treatments and subsequent tensile strain. The room -temperature and 1350°F tensile properties show a general increase ill strength and decreccse in ductility with increusing cold-work level. This is due to the dislocation taangling-. PerLurbatiot~s to this general trend occur- due to solid-solution weakening at the higher cold-work levels as a direct result of the preciplitation reactions. THE requirements for corrosion resistance and high-temperature strength place nickel-base alloys among the more promising materials for advanced nuclear reactor applications. However, when these alloys are irradiated at service temperatures, they generally suffer severe embrittlement'" and reduction in rupture life.3 Certain experimental treatments resulted in improvements in the tensile and stress-rupture properties of Hastelloy X-280, a solution-hardened nickel-base alloy.' To provide a basis for understanding these improvements, unirradiated tensile specimens were examined by electron microscopy. The results are reported in this paper. EXPERIMENTAL DETAILS Material. Hastelloy X-280, a low-cobalt version of Hastelloy X, is a member of the solution-hardened class of nickel-base alloys. The Hastelloy X-280 was obtained from 4- and 1-in: thick plates in the mill -annealed condition. Table I gives the chemical composition of the material as reported by the National Spectrographic Laboratories. ~x~erimental Treatments. Plates of suitable size, 12 by 3 by 1 in., or by + in., were cut under a water jet from the stock material and examined ultrasonic -ally for homogeneity of grain size and absence of voids. The acceptable plates were solution-treated at 2150°Ffor 1 hr and air-cooled. These plates were then reduced in thickness by cold rolling 0, 10, 15: or 20 pct along the original rolling direction. The plates were machined into buttonhead tensile specimens with a gage diameter of 0.125 in., with a gage length of 1.125 in., and with their tensile axes parallel to the rolling direction. The specimens were examined for quality of finish with a penetrant dye, ultra son ically checked for voids, and finally given a dimensional tolerance check with an optical comparator. The acceptable specimens were aged for 24 hr at either 1000" or 1500 F and air-cooled. These specimens were then held at 540°F in a water loop for approximately 18 days to qualify as controls for similar specimens irradiated under the same conditions of time, temperature, water chemistry, and flow rate. Table U summarizes the treatments. These treatments were investigated to establish whether prior precipitation and stabilization of carbide phases at strain sites within the matrix could reduce the amount of carbides available for precipitation at grain boundaries during service. Tensile-Test Conditions. Specimens were tested to fracture at room temperature or 1350 F in air on an Instron tensile-testing machine at a crosshead speed of 0.05 in. per min. The time for the furnace to reach equilibrium at 1350°F was approximately 30 min; soak time prior to testing was 15 min; and test duration was approximately 5 min.

Jan 1, 1968

By Morris J. Elsing

FOR MANY YEARS lead and zinc have had the so-called protection of a tariff and it is the purpose of the following brief discussion to show what' such protection actually accomplishes with a view to forecasting the possible results of the present copper tariff. In analyzing the subject, tabulations of the United States production, consumption, imports and exports, including ore and concentrates and all of the metallic products, of both lead and zinc have been made for each year since 1900. Of these data, the relationship of the imports and exports and the relative foreign and domestic prices are shown in Table 1. The conclusions drawn from these figures are listed below. 1. The United States is an exporter of zinc. 2. The United States is an importer of lead. 3. The average price of zinc at St. Louis for the last 32 years has been no higher than on the London market even though zinc and zinc ore have "enjoyed" a protective (?) tariff of varying amounts per pound for 22 years of this period. 4. The average price of lead on the New York market for 32 years has been 1.2c. per pound higher than on the London market, the tariff varying from 0.75 to 1.5c. per pound of lead in ore, and 1 to 2c. or more on manufactured lead.

Jan 1, 1932

By C. W. Sherman, N. J. Grant

The correlation of the high temperature chemical properties of slag-metal systems with some easily measured property of either slag or metal at room temperature has been the goal of both process metallurgists and melting operators for many years. There are several rapid methods for estimating various constituents in steel in addition to the conventional chemical methods which are quite fast, but these do not reveal the nature of the slag as a refining agent, which is of primary interest to the steelmaker. Furthermore, there are several methods for examining slag, the three principal ones being slag pancake, petrographic examination, and the previously mentioned chemical analysis. The main objection to the last two is the lime required to make a satisfactory estimate of the mineralogical or chemical components. The objection to the first is the inadequacy of the information obtained. A new technique has been developed by Philbrook, Jolly and Henry1 whereby the properties of slags are evaluated from an aqueous solution leached from a finely divided sample of slag. It is known that the pH or hydrogen ion concentration (of saturated solutions that have dissolved certain basic oxides, notably calcium oxide) will indicate a pronounced basicity. Philbrook, Jolly and Henry devised the pH measurement technique in order to supply open hearth operators with a fast, reasonably accurate method of estimating slag basicity. They offered the method as an empirical observation and made no claims as to its theoretical justification. The results were presented as an experi-metally observed relationship which applied over an important range of basic open hearth slags. They found that, in plotting the measured pH against the basicity, the best relationship existed between the pH and the log of the simple V ratio, CaO/SiO2. Extensive investigation also showed that there were several variables in the experimental technique that influenced the results and necessitated following a standard procedure to obtain reproducible pH readings. These variables were: 1. Particle size of the slag powder used. 2. Weight of sample used per given volume of water. 3. Time of shaking and standing allowed before the pH was measured. 4. Exclusion of free access of atmospheric carbon dioxide to the suspension. 5. Temperature of the extract at the time the pH was measured. In subsequent investigations of the pH method by Tenenbaum and Brown2 and by Smith, Monaghan and Hay3 the general conclusions of Philbrook's work were reaffirmed. It was the object of the present investigation to extend the technique to a point where it could be used to evaluate slags of all types. Experimental Results PARTICLE SIZK OF SLAG POWDER A large sample of commercial blast furnace slag of intermediate basicity (V-ratio 1.15) was selected for the study. The slag had been put through a jaw crusher until all of it passed through a 20 mesh screen. Five fractions of this crushed material were separated, -20 to +40, -40 to +60, -60 to +100, -100 to +200, and -200 mesh. A representative sample of 0.5 g was removed from each fraction and the pH determined using the method of Philbrook. Check pH analyses on the sample fractions varied due to the different amounts of shaking. To eliminate this variable, a mechanical shaker was employed. In order to know the exact time of contact between the slag and water, it was found necessary to filter the extract at the end of the shaking period. Using the mechanical shaker and a filtering apparatus, similar runs were made on the five fractions for contact times of 5, 10, 20, and 40 min. Random checks gave reproducible results within 0.02 pH. The data are plotted in Fig 1. It can be seen from the plot that each slag fraction is hydrolyzed to an extent that is roughly proportional to the surface area exposed to the water. The (—100 to +200) mesh material changed very little in pH after 10 min. shaking time. The curves are symmetrical and lie in proper relation to one another. The —200 mesh curve appears to be somewhat flatter than the others, but this can be attributed to the portion of very fine material that is not present in the other fractions. The closeness of the (-100 to +200) mesh curve to the —200 mesh curve and the fact that a —100 mesh sample would contain amounts of slag down to 1 or 2 microns in diam were considered sufficient reasons for selecting a —100 mesh sample as representative of the whole sample of slag for the purposes of this investigation.

Jan 1, 1950

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

THERE has been considerable discussion among A metallurgists and others interested in the development of titanium alloys as to the nature of the fine line markings which appear in the microstruc-tures of unalloyed titanium and a titanium alloys. These markings have been variously called x phase, etching pits, and twins. Figs. 1 to 3 show typical examples of the line markings as they appear, respectively, in high purity iodide titanium, commercial purity titanium rod, and a high purity a alloy containing 0.2 pct N. The commercial purity titanium sample, shown in Fig. 2, contains both line markings and some spheroidal retained-ß phase. The ß phase seen in this micrograph should not be confused with the line marking, since it originates from the iron present as an impurity in the sponge metal. It will be noted that the line markings seem to have a definite orientation pattern with respect to the grains and in titanium noticeably resemble the precipitation occurring in artificially aged high purity Al-Cu alloys. This similarity led to the hypothesis that the line markings observed in titanium and a titanium alloys resulted from precipitation of some unknown phase. With the work of Hägg1 and McQuillan2 as background, there was little reason to suspect hydrogen of being responsible for the line markings. Hagg reported that up to 33 atomic pct H was soluble in a titanium, and McQuillan reported an a solubility of up to 8 atomic pct. Furthermore, McQuillan examined metallographically a 5.1 atomic pct H alloy quenched from 300°C and stated that the structure appeared to be a single-phase a solid solution. Line markings have been observed frequently and were first noted by Jaffee and Campbell3 in 1949. They did not observe them in vacuum-annealed titanium and a Ti-O and Ti-N alloys, but did observe them in Ti-H alloys containing 0.25, 0.5, and 1 atomic pct H. They stated that it was doubtful that the markings were a second phase based on hydrogen, because 1 atomic pct was far from the accepted solid solubility of hydrogen in titanium. Finlay, Resketo, and Vordahl,4 in 1950, concluded that the markings were a true second phase as a result of observations on their etching characteristics. Anderson5 Commenting on these markings in titanium was inclined to associate them with hydrogen, but was loath to call them titanium hydride, because of the reported high solubility of hydrogen. Work at Battelle Memorial Institute for the Navy Bureau of Aeronautics," done concurrently with the work described in this paper, provided information on the experiment converse to that described by Jaffee and Campbell in 1949. This work showed that the amount of line markings in unalloyed titanium could be decreased by vacuum annealing at elevated temperature. It was suggested that this was the result of removal of hydrogen; previously, the data of Jaffee and Campbell9 howed that the markings appeared when hydrogen was added. Recent work at Battelle for the Ordnance Corps, Department of the Army, which is described here, now establishes the identity of the markings as a titanium hydride phase. A sample of high-purity titanium rod 1/4 in. diam, 0.009±0.001 wt pct H (0.43 atomic pct), Fig. 1, was resistance heated in a 0.05 micron vacuum for 41/2 hr at 1500°C. During the early states of heating, the pressure increased to 150 microns, indicating that gases were being evolved. After cooling in vacuum, the iodide titanium rod was analyzed for hydrogen. Vacuum-fusion analysis showed 0.0006 ±0.0003 wt pct H (0.03 atomic pct) to be present.* Metallographic examination of the vacuum-annealed rod showed only a transformed ß structure. There was no evidence of fine line markings, Fig. 4. A section of this vacuum-annealed rod was cold rolled to 0.040 in. thick sheet and annealed for 1 hr

Jan 1, 1953

By N. B. Wittman

The working of blast-furnaces is always of interest to many members of the Institute, for which reason I present an account of the working of the furnaces of the E. and G. Brooke Iron Company, of which I have had charge for the past four years. Although there are no phenomenal runs to record, there have been long periods of satisfactory work, and also periods—altogether too long—when one of our furnaces has behaved in a way which may be described as "nagging." All the conditions were apparently normal,but only a very light burden could be carried, which of course resulted in a high fuel-consumption to the ton of iron, as well as increased cost of labor. The two active furnaces of this company have the following dimensions and equipment : No 2. No 3. Feet. Feet. Height ....55 60 Diameter at bosh,.....- 15, 16 " hearth,...... 8 74 " stock-line,..10 91/2 Height of bosh,..23 23 " tuyeres,. 5 5 Diameter of bell,.7 6 Front,....closed open Both furnaces are blown with I. P. Morris condensing-engines, sim

Jan 1, 1890

By J. E. Hilliard

Isobaric sections of the eutectoid region of the iron-carbon phase diagram have been exgerimentally determined at 35, 50, and 65 kb. The phase boundaries were located by metallographic analysis of specimens quenched after equilibriatwn at known temperatures and pressures. With increasing pres -sure a pronounced decrease in the solubility of FesC in austenite was observed together with a depression of the eutectoid temperature. These two effects resulted in a shift of the eutectoid composition toward a lower carbon content; at 65 kb the eutectoid was at less than 0.2 wt pct C. These results are in qualitative agreement with thermodynamic calculations. It has also been shown by calculations that Fe3C in contact with saturated austenite will be stable with respect to both graphite and diamond formation at all pressures above -3.5 kb. 1 HE investigation described in this article was part of a more general study of the effect of high pressure on transformations in Fe-C alloys. Thermodynamic calculations and exploratory runs made in 1959 at the start of the program indicated an appreciable change with pressure in the phase equilibria of Fe-C alloys. However, the calculations were not considered reliable enought to provide the quantitative information required for the interpretation of the effect of pressure on the kinetics of transformations. An experimental investigation was therefore made to determine a series of isobaric sections of the eutectoid region of the phase diagram at pressures up to 65 kb. EXPERIMENTAL PROCEDURE Materials. Seven alloys with analyzed carbon contents of 0.10, 0.20, 0.38, 0.60, 0.77, 0.93, and 1.20 wt pct C were prepared from Ferrovac" iron and high-purity graphite induction melted in magnesia crucibles under argon. The ingots were hot worked and swaged down to 0.19-in.-diam rod which was then centerless ground to a final diameter of 0.125 in. Samples for chemical and spectrographic analyses were taken from each end of the rods. The prin- cipal impurities were found to be Ni, Al, Co, and Si which were present in amounts up to 0.03, 0.02, 0.01, and 0.01 wt pct, respectively. Specimens were prepared by slicing the ground rods into pills 0.06-in. thick which were silver plated to reduce decarburization during the equilibration. Silver was chosen for this purpose because of its very low solubility for carbon and its mutual immisicibility with iron. High-Pressure Apparatus. The high-pressure runs were carried out in the "Belt" apparatus.' As shown in Fig. 1, this consisted of a cylindrical cell compressed between two Carboloy punches loaded by a uniaxle press. Radial support to the cell was given by the "belt" which was a Carboloy die heavily prestressed by a series of steel binding rings. Laminated gaskets of lava and metal separated the punches from the inner surface of the "belt". A cross-section of the high-pressure cell is shown in Fig. 2. Two specimen pills were located inside a resistance heater of 0.20-in.-diam Nichrome tubing. The ends of the tube were sealed with alumina and lava pills tamped in place after the

Jan 1, 1963

In Bulletin J 1, recently published by the Traylor Engineering and Manufacturing Co., it is stated that the largest jaw crusher ever built has a jaw opening of 66 in. by 86 in. and weighs 680,000 1b. It is said to be in successful operation and has a capacity of 490 tons per hour crushed to 12-in. size; 415 tons per hour crushed to 10-in. size; 330 tons per hour crushed to 8-in. size. The same company, in its Bulletin G 3, gives a diagram showing the percentage of a crushed product which will pass through screens of different sizes of perforation from a machine adjusted to a certain size screen. This diagram is reprinted below for the information of our members and the following notes apply to it. In order to prevent an excessive amount of fines, crushing machines are usually set so that 15 per cent. of the product will be larger than the maximum size desired, and this oversize is then recrushed by smaller

Jan 10, 1916

By D. F. Kaufman, E. D. Levine, L. R. Aronin

ThE primary slip plane in hcp metal crystals can usually be inferred from the c/a ratio. Basal slip is the primary system at room temperature for zinc, cadmium, magnesium, cobalt, and rhenium, all of which have a c/a ratio greater than 1.60. Zirconium and titanium, on the other hand, each with a c/a ratio of 1.59, deform primarily by (1010) [ll20] prismatic slip. The increasing tendency toward prismatic slip in these materials is generally thought to be associated with the increase in atomic density on (10i0) as c/a is reduced. Beryllium, with a c/a ratio of 1.57, would, according to the above scheme, be expected to exhibit prismatic slip. However, in beryllium of commercial purity, the primary deformation mode at room temperature is basal slip.' The ratio of critical shear stress for prismatic to that for basal slip at room temperature is approximately 5:l. The critical shear stress for prismatic slip decreases quite rapidly with increasing temperature, however, and at 500°C the ratio is approximately unity. The apparently anomalous behavior of beryllium has led to speculation that prismatic slip in this material may be restricted by an anisotropic effect of impurities,' and that, if beryllium could be purified to a sufficient extent, prismatic slip might predominate at room temperature. In such a case, the conditions under which basal cleavage can occur would be suppressed, and enhanced low-temperature ductility might result. With the advent of the floating-zone method for purification of beryllium,3 it has become possible to determine experimentally the effects of purification on basal and prismatic slip. Tensile tests were performed at room temperature on single crystals oriented favorably either for basal or prismatic slip. The crystals had been purified to various extents by zone-refining, employing procedures that have been described elsewhere.4 Relative purities of the crystals were estimated by measuring the ratio of electrical resistance at 4.2"K to that at 298°K. Typical values ranged from 0.40 for commercial-purity material to 7.7 X 10"4 for crystals prepared from vacuum-distilled beryllium and subjected to six zone-refining passes. The purity dependence of the critical shear stresses for basal and prismatic slip is shown in Fig. 1. In the purity range studied, the critical shear stress for basal slip is decreased from 1.4 to 0.14 kg per sq mm. The critical shear stress for prismatic slip is decreased from 6.7 to 5.3 kg per sq mm. The decreases in critical shear stress for each deformation mode, therefore, are approximately equivalent. No purification anisotropy is observed. Because of the absolute magnitudes of the critical stresses, the ratio of the critical shear stress for prismatic slip to that for basal slip actually increases from 5:l to 38:l at the highest purity level studied. It is evident, therefore, that basal slip is the primary deformation mode in high-purity beryllium. This fact must be accounted for in any rationalization of the deformation behavior of hcp metals. This work was performed at Nuclear Metals, Inc., under the sponsorship of the U.S. Atomic Energy Commission.

Jan 1, 1964

By K. E. Beu

IN the measurement of retained austenite concentrations in steels using the integrated intensity method,1 Averbach has pointed out" that the absorption factor A(0) for a flat sample making a glancing angle 4 with the incident X-ray beam can be combined with his constant factor R to obtain our constant factor" G provided that "1—There is no preferred orientation in the sample, and 2—The geometric requirements [for the sample, film, and X-ray beam] have been met precisely."' If A(0) can be combined with R to give G according to the equation G = R . A(0) [14] then the possibility for making non-compensating errors in the austenite determination has been eliminated. This has been described previously in a technical note." Because of the brevity of the previous note,3 it was impossible to emphasize the fact that the two conditions on preferred orientation and geometry can be easily met experimentally, contrary to Aver-bach's statement that: ". . . the necessary conditions must be tested experimentally for each determination, and this is done most easily by observing whether the apparent absorption has the form of Eq. 2 [the theoretical equation for A(0)]."" he way in which these two conditions can be met experimentally will be discussed briefly to help clear up this point. In addition to these two conditions, other factors such as sample shape, homogeneity, and grain size which also affect A will be included in this discussion. A (0) depends on sample shape. The theoretical function for A was derived originally for a flat surface.' In general we have found that a flat sample surface is readily obtainable." If such a surface can * The effect of surfaces which are not flat on the measurement of retained austenite will be discussed later. be obtained, it has the following advantages: 1—it is easily reproducible from sample to sample, 2—it is the form required for metallurgical examination —this type of examination being frequently desirable for this work, and 3—it is an efficient shape for diffraction purposes. Perhaps the most important of these features is that a flat sample surface is easily reproducible; hence, this requirement on the repro-ducibility of A from sample to sample is met for all such samples. Fig. 1—Schematic diagram of the quartz crystal monochromator diffraction unit. The centerline of the main beam is at 6' to the target face. The tangent to the crystal face is at 16.8' to the moin beam. The centerline of the monochromatic beam is at 33.6 to the main beam. The sample surface can be rotated in its own plane. The angle of the sample surface and the monochromatic beam can be adjusted by rotating about the vertical axis, The film holder can also be rotated about B so that the film can be exposed over the desired angular range. For Fe K, X = 1.932A. 1011 planes of quartz have d = 3.35A. A(0) depends on homogeneity and grain size. If the sample is badly segregated or the grain size is large, the effect of micro-absorption and primary extinction1. ' must be considered. It has been shown, however, that for most plain carbon or low alloy hardened steels, neither micro-absorption nor primary extinction effects are present.' A (0) depends on camera geometry. For a given angle 0, A remains theoretically constant from a geometrical viewpoint only if the following factors are kept constant: 1—the angle of inclination .+ of the sample to the X-ray beam, and 2—the centering of the sample with respect to the film cylinder. These are mechanical problems which can be solved readily if the facilities of a good machine shop are available. The arrangement used to insure that the angle 4 remains constant and the centering of the sample is reproducible is indicated schematically in Fig. 1. The sample is clamped against a thin plate with a hole in it by means of a spring-loaded pres-

Jan 1, 1954

By R. N. Orava

TO the author's knowledge, only one satisfactory high-resolution technique for etch-pitting dislocations in Cu-Zn alloys has been published.' In that account, pits in 70/30 brass single crystals were produced by etching electrolytic ally in a 30 pct orthophosphoric acid bath. Thereafter, observations were made from surface replicas by electron microscopy. The method of pitting and observation permitted the high resolution necessary for the distinction of individual dislocations in arrays of pile-ups. However, no comment was offered concerning the possibility of obtaining pits which are amenable to optical resolution. Moreover, for adequate results, the electrolytic pitting process is invariably preceded by a polishing stage which could obscure the surface features of interest. Consequently, it would be desirable to be able to delineate, by solely chemical means, dislocations which could be detected by both optical and electron metallo-graphic techniques. This was achieved by the simple expedient of modifying two etchants reported by young2 to reveal dislocations on the (100) planes of pure copper. Single crystals of 70/30 a brass, described previously,3 were sectioned to provide a surface parallel to a set of {100) planes, mechanically polished, and subsequently electropolished at 2.4 v in a solution comprised of 2 parts H3PO4, 4 parts ethanol, and 3 parts water. The inclusion of ethanol tended to inhibit nonuniform surface attack. Etch-pitting was effected by a 2 to 3 sec immersion in a 70 pct aqueous solution of HNO3. The samples were then washed in a fast-flowing stream of water, and rinsed further in distilled water, and ethanol, before drying. It is important to note that this reagent should be either used immediately after mixing, or, if allowed to cool, reheated to about 35°C prior to use. No pitting was obtained at room temperature. Typical results are shown in Fig. 1 where (a) is an optical view of the pitted surface and (b) is an electron micrograph of a silicon monoxide replica shadowed with tungsten oxide. The former is characteristic of a somewhat longer etching time (-6 to 8 sec) which varied with bath temperature. Similar pits accrued from a 1/10 aqueous dilution of another of Young's solutions2—2 M FeC1,6H20 and 7.8 M HBr.

Jan 1, 1968

By R. S. Wagner, W. C. Ellis

A new mechanism of crystal growth involving oapor, liquid, crnd solid phases explains many observations of the effect of implurities in crystal growth from the vapor. The role of the impuuitq is to form a liquid Solution with the crystalline tnalerial to be grown from the vapor. Since the solution is n prefevred site for deposition firorti the uapor, the liquid becorrles supersaturated. Crystal growth occurs by precipitatzon from the supersaturated liquid crt tlie solid-liquid zntevfnce. A crystalline defect, such as a screw dislocation, is not essetztial for VLS (vapor -liquid-solid) growth. The concept of the VLS mechanism is discussed in detail with reference to tire controlled growth of silicon crystals using gold, platinum, palladium, nickel, silver, or copper as an implurity agent. RECENTLY a short communication' described a new concept of crystal growth from the vapor, the VLS mechanism. In this paper we present a detailed description of the process and its application to the growth of silicon crystals and we discuss its relevance to existing concepts of .'whisker" crystal growth. Crystal growth from the vapor is usually explained by a theory proposed by Frank2 and developed in detail by Burton, Cabrera, and Frank.3 In this theory a screw dislocation terminating at the growth surface provides a self-perpetuating step. Accommodation of atoms at the step is energetically favorable, and is possible of much lower supersatu-ration than required for two-dimensional nucleation. Crystals of a unique form resulting from aniso-tropic growth from the vapor are "whisker" or filamentary ones. Such crystals have a lengthwise dimension orders of magnitude larger than those of the cross section. For most filamentary crystals both the fast-growth direction and directions of lateral growth have small Miller indices. The special growth form for a whisker crystal implies that the tip surface of the crystal must be a preferred growth site. sears4 proposed that, according to the Frank theory. a whisker contains a screw dislocation emergent at the growing tip. Such an axial defect provides a preferred growth site and accounts for unidirectional growth. The hypothesis was extended by Price. Vermilyea. and Webb," still implying the presence of a dislocation at the whisker tip. They postulated that impurities arriving at the fast-growing tip face become buried while those arriving on the surface of slow-growing lateral faces accumulate and thereby hinder growth. These considerations led to a whisker morphology. There is increasing evidence that most whisker crystals grown from the vapor are dislocation-free. Webb and his coworkers6 searched for an Eshelby twist7 in zinc? cadmium, iron. copper, silver, and palladium whisker crystals. They found unequivocal evidence for an axial screw dislocation in only one element, palladium. However, not every palladium crystal examined contained a dislocation. Observations with the electron microscope have failed to show dislocations in whisker crystals of zinc, silicon.9 and one morphology of AlN.10 Since many whiskers are completely free of dislocations, an axial dislocation does not appear to be required for whisker growth of many substances. A significant advance in understanding whisker growth has been a recognition of the need for impurities. This requirement has been clearly demonstrated for copper,11 iron,13 and silicon9-1 whiskers. For silicon, detailed studies proved conclusively that certain impurities, for example, nickel or gold, are essential. Another pertinent phenomenon which has received little attention is the presence of a liquid layer or droplets on the surface of some crystals growing from the vapor. Crystals in which this has been observed include p-toluidine,14 MoO3,15 ferrites,16 and silicon carbide.'" The liquid layers or globules were considered to be metastable phases, molecular complexes, or intermediate polymers originating from condensation of the vapor phase. The possibility has been suggested that the halide being reduced is condensed at the tip18 or adsorbed on the surface11 of a growing metal whisker, for example copper. The literature on whiskers discloses illustrations of rounded terminations at the tips. These appear. for example, on crystals of A12O3,19,20 sic,21 and BeO.22 For BeO, Edwards and Happel suggested that during growth of the whisker the rounded termination consisted of molten beryllium enclosed in a solid shell of BeO. A recent paper9 on the growth of silicon whiskers contains many observations pertinent to an understanding of the mechanisnl of whisker growth. These observations are summarized as follows. 1) Silicon whiskers are dislocation-free. 2) Certain impurities are essential for whisker growth. Without such impurities the silicon deposit is in the form of a film or consists of discrete polyhedral crystals.

Jan 1, 1965

By F. A. Forward, J. Halpern

A new process for extracting uranium from ores with carbonate solutions is described. Leaching is carried out under oxygen pressure to ensure that all the uranium is converted to the soluble hexavalent state. By this method), alkaline leaching can be used successfully to treat a greater variety of ores, including pitchblende ores, than has been possible in the past. The advantages of carbonate leaching over conventional acid leaching processes are enhanced further by a new method which has been developed for recovering uranium from basic leach solutions. This is achieved by reducing the uranium to the tetravalent state with hydrogen in the presence of a suitable catalyst. A high grade uranium oxide product is precipitated directly from the leach solutions. Vanadium oxide also can be precipitated by this method. The chemistry of the leaching and precipitation reactions are discussed, and laboratory results are presented which illustrate the applicability of the process and describe the variables affecting leaching and precipitation rates, recoveries, and reagent consumption. THE extractive metallurgy of uranium is influenced by a number of special considerations which generally do not arise in connection with the treatment of the more common base metal ores. Perhaps foremost among these is the very low uranium content of most of the ores which are encountered today, usually only a few tenths of one percent. A further difficulty is presented by the fact that the uranium often occurs in such a form that it cannot be concentrated efficiently by gravity or flotation methods. In these and other important respects, there is evident some degree of parallelism between the extractive metallurgy of uranium and that of gold and, as in the latter case, it has generally been found that uranium ores can best be treated directly by selective leaching methods. It is readily evident that this parallel does not extend to the chemical properties of the two metals. Unlike gold, which is easily reduced to metallic form, uranium is highly reactive. It tends to occur as oxides, silicates, or salts. Two ores are of predominant importance as commercial sources of this metal: pitchblende which contains uranium as the oxide, U3O51 and carnotite in which the uranium is present as a complex salt with vanadium, K2O-2UCV3V2O5-3H2O. These ores may vary widely in respect to the nature of their gangue constituents. Some are largely siliceous in composition, while others consist mainly of calcite. Sometimes substantial amounts of pyrite or of organic materials are present and these may lead to specific problems in treating the ore. Further complications may be introduced by the presence of other metal values such as gold, copper, cobalt, or vanadium whose re- covery has to be considered along with that of the uranium, or whose separation from uranium presents particular difficulty. In general, there are two main processes for recovering uranium in common use today.'.2 One of these employs an acid solution such as dilute sulphuric acid to extract the uranium from the ore. A suitable oxidizing agent such as MnO, or NaNO, is sometimes added if the uranium in the ore is in a partially reduced state. The uranium dissolves as a uranyl sulphate salt and can be precipitated subsequently by neutralization or other suitable treatment of the solution. The second process employs an alkaline leaching solution, usually containing sodium carbonate. The uranium, which must be in the hexavalent state, is dissolved as a complex uranyl tricarbonate salt, and then is precipitated either by neutralizing the solution with acid or by adding an excess of sodium hydroxide. The latter method has the advantage of permitting the solutions to be recycled, since the carbonate is not destroyed. This is essential if the process is to be economical, particularly with low grade ores. With each of these processes, there are associated a number of advantages and disadvantages and the choice between using acid or carbonate leaching is generally determined by the nature of the ore to be treated. In the past, more ores appear to have been amenable to acid leaching than to carbonate leaching and the former process correspondingly has found wider application. With most ores, acid leaching has been found to operate fairly efficiently and to yield high recoveries. One of the main disadvantages has been that large amounts of impurities, such as iron and aluminum, sometimes are taken into solution along with the uranium. This may give rise to a high reagent consumption and to difficulties in separating a pure uranium product. Excessive reagent consumption in the acid leach process also may result

Jan 1, 1955

By E. A. Lawrence

The experiences of Canex Placer Ltd. in establishing vegetation on a lead-zinc tailing pond are presented, hoping others with similar challenges will be benefited. History The tailing ponds are the result of 23 years of mining and milling operations, which ceased in August 1970. Roughly 7.9 million tons of lead-zinc ore were removed in that time. The ponds are located between Salmo River and B.C. Highway 3, about 8 miles north of Nelway near the Canada-U.S. border.

Jan 1, 1975

By Richard F. Miller

Recent studies of creep have made it apparent that plastic deformation may occur in metals under stresses less than the elastic limit as determined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapselll said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was determined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instruments by A. W. Hanson4 on zinc and by Podaschewsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc. AppaRatus The creep-testing apparatus developed for this work is shown in Figs. 1 and 2. The extensometer A is sensitive enough to detect changes in length of 3.3 X 10~6 in. per in., and yet can be used into the plastic range without injury to the apparatus. The specimen,

Jan 1, 1936

By J. B. Austin, R. H. H. Pierce

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of, carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is .cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ?-a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dilatometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has. been described.2

Jan 1, 1935

By J. B. Austin

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measure-ments serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transforma-tion temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chro-mium or managanese. The lag, or undercooling, observed at the ? - a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2

Jan 1, 1935