Search Documents

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By G. R. Love

i\ program has been written which allows fully automatic conversion of data for X-ray intensity, as a function of time, to finished conventional pole figures. The program accepts input data in the serial order in which they are taken and is therefore immediately compatible with automatic data-acquisition devices. From these data taped instructions are prepared for the Calcomp plotter to construct ink-on-paper drawings. Because both Siemens and Norelco pole figure goniometers are used in this laboratory, the program was written for pole figure data obtained from one or more interpenetrating spiral scans during which both the polar angle, @, and the equatorial angle, a, are varied simultaneously and continuously. The reference direction for a scan, that is the point @ = 0 deg, may be chosen coincident with either the normal direction (N.D. figures) or the rolling direction (R.D. figures). In either case the plotted figures are drawn with the transverse direction (a = 0 deg) at the right and the rolling direction at the top. The full, circular, pole figure is drawn as two semicircular figures labeled "front side" and "back side". As presently constituted, the program will also accept data from circular scans taken at constant values of @. In every case the angular coordinates of each intensity entry are generated in the computer from a relatively small number of auxiliary data. The X-ray intensity data are corrected for background scattering by direct subtraction of the intensity measured with 28 set appropriately "off" the Bragg angle. It is possible to enter this correction as an additional spiral scan through the a, @ space; because the background correction does not normally vary rapidly enough to warrant this detailed a determination, the background corrections are entered as one or more auxiliary data. All data are normalized to a multiple of random intensity. The data taken in this laboratory for N.D. figures are normally taken in a reflection geometry from from sheet samples and do not extend beyond <p = 75 deg; for these data random intensity must be determined from separate experiments and entered as auxiliary information. When the auxiliary information is not available, a number is chosen to give intensity values normalized to a scale of 1 to 10. In this laboratory, R.D. figures are based upon hemispherical samples for which data are taken out to @ = 90 deg; for these data random intensity is calculated by direct numerical integration of . sin @ d@ using the trapezoidal rule and the background-corrected values of the input data. Points necessary to the construction of the pole figure are identified by simple linear interpolation between adjacent data points to determine the loci of contour lines. Points lying on a given contour are connected to one another with straight-line segments and the search-calculation-drawing sequence is patterned to assure that different contour lines do not cross, that a single line does not branch, and that lines do not end in space. However, so that there be no ambiguity in the data presentation, all contour lines end at the limits of the input data. Since the curves are constructed of straight-line segments, they are not continuous in their derivatives. However,

Jan 1, 1969

By M. G. Corson

Information regarding the use of ixanganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists. Properties of Manganese Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850" C. and the other below 650" C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. Manganese as a Scavengek Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the silicides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. MANGANESE AS A SCAVENGER Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

Jan 1, 1928

By Arthur F. Taggart, A. W. Thomas, T.C. Fitt

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By P. Chiotti, G. R. Kilp

IN the study of zinc-zirconium1 and zinc-uranium2 systems, vapor-pressure measurements were made in order to establish the equilibrium phase diagrams for a pressure of 1 atm. In each of these systems, only zinc has an appreciable vapor pressure over the temperature range investigated. The zinc pressure was measured over a sufficiently wide temperature and composition range to permit calculation of the standard free energy, enthalpy, and entropy of formation for the compounds ZrZn, ZrZn2, ZrZn3, ZrZn6, ZrZn14 , and U2Zn17. In these calculations the compounds were treated as line compounds. Although the exact composition range was not determined, metallographic and thermal data indicate that the solubility range for these compounds is small. It is to be noted that the compound initially reported to correspond to the formula UZn9, 2 has been shown by the crystal structure work of Makarov and vinogradov3 to correspond to the formula U2Zn17,. The crystal structure is similar to that for the compounds Th2M17, investigated by Florio,4 et al; here M represents iron, cobalt, or nickel. Therefore, thermodynamic calculations are based on the formpla U2Zn17 EXPERIMENTAL The dew-point method employed to measure the vapor pressure of zinc over uranium-zinc alloys has been described previously.2 The same procedure and apparatus were used in measuring the zinc pressure over zinc-zirconium alloys. In the case of alloys in the two-phase region consisting of a zirconium and the compound ZrZn, the Knudsen effusion method was employed to obtain a few values in the temperature range 600" to 560°C. In most cases, tantalum crucibles were used to contain the zirconium alloys. THERMODYNAMIC PROPERTIES OFU2Zn17 A least-squares treatment of the vapor-pressure data obtained for 35 and 65 wt pct U alloys in the temperature range 650° to 940°C gave lOg10PAtm = 7,713/T + 6.33 Here, as in following equations, T represents degrees kelvin and P represents the zinc vapor pressure in atmospheres. The probable errors for the two constants were calculated to be 60.68 and 0.0563, respectively. This relation represents the equilibrium dissociation pressure for the reaction U2Zn17 (s) - 2U(s) + 17Zn(v) The solubility of zinc in solid uranium is negligible and the only additional information required to calculate the free energy of formation of U2Zn17 is the free energy of vaporization of pure zinc. K. K. Kelley5 gives the relations, AF°= 30,902 + 6.03Tlog T + 0.275 X 10-3T2 - 45.03T

Jan 1, 1961

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

It was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a component of the pulp, of a mass solubility of the general order of a fraction of a milligram to I 5 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.= The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends. to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. Experimental Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well be~ond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipitation from hydrochloric acid solution of arsenic-free zinc, and was washed as lot I. Lot 3 was prepared by heating a portion of lot 2 in absence of air at 1200° to r300°C. for one hour."

Jan 1, 1943

By Strathmore R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

The effect of temperature as a parameter in ore flotation has not been systematically studied, although for some ores it has been known for many years that selectivity and grade of concentrates can be improved by conditioning or flotation at moderately or substantially elevated temperatures. In 1934 Coghill and Clemmer&apos; stated that "elevated temperature seems to make hard water more tolerable" in soap flotation, and a cursory examination of the literature indicates that some earlier investigators were aware of beneficial results obtained by floating above room or mill-water temperatures. Tartaron,&apos; Mitchell et al.,3 and particularly Hamilton et al." have shown that high pulp temperatures give high recovery and selectivity in soap flotation of fluorite from a variety of gangue minerals. As a result of the work of these and of other investigators, high-temperature flotation has been successfully applied to industrial flotation of fluorite. Falconer" stated: "The use of high temperature conditioning (above 35°C and preferably above 60°C) in connection with the soap flotation of nonsulphide ores, as covered in B. Kalinowski&apos;s French Patent No. 847,- 215, Dec. 7, 1938, is claimed to provide more intense activation, better separation of values from gangue, and reduction in quantity of reagents." The various investigations quoted above clearly demonstrate the improvements to be realized by increasing the temperature at which fluorite is floated, and it is surprising that little or no information has been published on systematic investigation of the same method as applied to other ores.

Jan 5, 1960

By Martti E. Maliniemi

The Svappavaara mine is located 47 km southeast of Kiruna C. The ore deposit now being worked, Leveäniemi, belongs to Luossavaara- Kiirunavaara AB (LKAB) and is the company&apos;s, and also Sweden&apos;s, third biggest mine after Kiirunavaara and Malmberget. The distance by rail to the Norwegian port of Narvik is 214 km and to Lulei on the Gulf of Bothnia 340 km (Fig. 1). The village of Svappavaara has about 800 inhabitants. The climate is arctic in character. The temperature during the months of December to February is about -20º to -35ºC, and the ground is covered by a blanket of snow for about eight months of the year. The brief, intensive summer often arrives with startling speed, bringing both sunshine and warmth. HISTORICAL BACKGROUND Mining operations took place in Svappavaara as far back as 300 years ago. During the period 1655-1684, copper ore was taken from the deposit called Gruvberget in the vicinity of the village. The total production of raw copper was probably about 1,045 tons. During the 18th and 19th centuries, several attempts were made to extract iron ore from the numerous deposits found within the district. These brave attempts, however, were foiled by the high phosphorus contents and the enormous transport difficulties. The present-day mine fields in Leveäniemi were discovered in 1897. At that time, it was difficult to determine the size and value of the deposit because of the thickness of the soil cover (3 to 15 m) and the

Jan 1, 1969

By Leroy Palmer

ALL the domestic. production of magnesite during 1925 came from two states, California and Washington. Of a total of 120,660 tons of crude ore, 64,600 tons, or 54 per cent., were produced in California.1 Of .this quantity California produced about 99 per cent. of the caustic calcined, but only 10 per cent. of the dead-burned. The largest producer was C. S. Maltby, of San Francisco, who operated the Red Mountain mine, in Santa Clara County, and the Sampson mine, in San Benito County, under lease. These two mines have been studied by the author, and offer interesting comparisons as to mining and treatment methods and final products. GEOLOGY The general geology of the magnesite deposits of California has been described by Hess,2 Bain3 and others,4 and although a detailed discussion is not necessary here, a brief summary will assist in understanding mining conditions. California magnesite, when comparatively pure, is usually a white, fine-grained rock, with a conchoidal fracture, occurring in veins and lense-like masses in serpentine. The veins vary considerably in width, and usually occur in a series of more or less parallel veins intersected by other series or systems of veins, probably following original or secondary fissures in the enclosing serpentine. The most generally accepted theory of origin is that the magnesite was formed by the action of surface waters charged with C02 percolating downward through fissures and changing the magnesium silicates of the serpentine into magnesium carbonate.

Jan 1, 1927

By J. B. Bassett, E. S. Rowland

The experimental work reported herein firas inspired by the publication of a paper by Grange and stewart, in which it was suggested that at low chromium contents the effect of this element on the Ma point was greater than at higher chromium contents, It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the M, point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature, such enrichment of the austenite in chromium content would lower the M, point nearer room temperature where cracking is more likely to occur. According, it was decided to investigate the effect of chromium, in quantities between o and 2 pet, on the M, point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the M, temperature values were corrected by means of the Grange and Stewart formulas to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (z) Hsereutectoid compos-sition&apos;: 1." pet carbon and O.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased error such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question Of the effect Of chromium On the Md Oint, particularly at low chromium contents. While it is fairly well established that chromium causes the M, to be lowered when present in quantities of I pet Or more, Grange and Stewart1 have suggested that in small amounts (less than 1 pet) it is more effective in lowering the Ma point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the Ma point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the Ma point of a 0.20 carbon steel. Material Two series of 35 Ib induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0,25 pet increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1949

By W. E. Bron, E. S. Machlin

GRAIN boundary migration in V-shaped thin specimens of high purity silver was studied. Each specimen contained two crystals having the relative orientation: (111)A/(111)B; (ll0)A/(101)B. The boundary between these two crystals varied between a continuous curved and an alternating two plane interface. The plane interfaces were oriented parallel to (101)A/(011B) and (121)A/(211)B. Traces of these planes are shown in Fig. 1. Evidently the two plane interface, although of higher area, comprises lower total interface energy than the average curved boundary it replaced. The plane boundaries were found to move at 650 °C to consume the broad segment of the V opposite to the direction of interface area and energy decrease. On investigation, using the thermal etching technique of Hendrickson and Machlin,1 it was found that the outer grain contained 8.3x108 more dislocations per cm" than the grain at the apex of the V. Consequently, the boundary moved to decrease the strain energy associated with the difference in dislocation density across the boundary. The rates of motion of specific {110} and {112} boundaries were measured during interrupted anneals at 650°C by referring the position of the boundaries to each other and a fiducial line on the specimen surface. The measured rates of motion are 0.075 and 0.025 mm per hr for the {110} and {112} boundaries, respectively. Plots of grain boundary motion vs time of annealing show straight lines with little deviation of data points from these lines.

Jan 1, 1957

By John B. Campbell, George G. Binder, Loren H. Jenks

Conventional methods of producing crude oil generally leave in the depleted reservoir 1 to 3 bbl of oil for every barrel brought to the surface. This paper describes a field test which explores the possibility of using gas-driven liquid propane to improve oil recovery efficiency. Laboratory theoretical and experimental studies leading to the field test indicated that low residual oil values could be obtained using limited amounts of propane driven by gas. The field test involved (I) repressuring the reservoir to the vapor pressure of liquid propane, (2) injecting the liquid propane, and (3) injecting dry natural gas to drive the propane and oil to the producing wells. Considerable preliminary work, including new drilling, work-overs, and a pressure survey was necessary. During the test, oil production rates have averaged about nine times the final primary rates. The field average GOR is still below the pre-test value. Oil recovery to date is 112,000 STB. About one-third of the 143,-000 bbl of propane injected has been produced to date. Results of the C-2 block test are encouraging and larger, more definitive field projects ore indicated. INTRODUCTION The cost of finding new crude oil reservoirs continues to increase. Today the oil industry is drilling more and deeper wells and making fewer big discoveries. Nevertheless, the demand for oil and oil products increases each year. It is natural that oil companies, faced with this situation, concentrate on recovering more of the oil existing in our known crude oil reservoirs. There is room for much improvement. For every barrel of oil brought to the surface by present day methods of producing crude oil, generally 1 to 3 bbl are left behind in the depleted reservoirs. The "unrecoverable" oil in petroleum reservoirs is largely "trapped" by capillarity. Since flushing with a solvent is exceedingly effective in combatting oil loss due to capillarity, much effort in this direction has been made in recent years1,2,3,4,5. Liquefied petroleum gas (LPG) has been suggested as a relatively inexpensive. abundant, easily recoverable solvent for crude. Some operators have observed striking responses in oil recovery at production wells offsetting input wells in LPG storage reservoirs6,7,8. In spite of the low unit cost of LPG, however, it is uneconomic in general to inject a volume of LPG into a reservoir to remove a like volume of oil. A modification of solvent flushing in which a limited quantity of liquid propane is gas driven through a reservoir appears capable of recovering much more than 1 bbl of oil per barrel of propane injected. Also, most of the propane injected should be recoverable for sale or re-use. Since such a process could well have widespread and profitable application, The Carter Oil Co. is making an extensive evaluation of the technique&apos;s possibilities. Laboratory development of the gas-driven propane recovery technique was sufficiently encouraging to justify testing in the field. Since 1952, the Production and Research Departments of The Carter Oil Co. have cooperated in a field test in the C-2 Block leases of the

Jan 1, 1958

By M. R. Louthan, C. L. Angerman

In polycrystalline Zircaloy-2 the orientation of zirconium hydride precipitates is influenced by an applied stress during hydride precipitation; hydride platelets are oriented nearly parallel to a compres-sive stress and perpendicular to a tensile tress. 1,2 A similar effect has been observed in the Ti-H system, where precipitation of the low-density hydride platelets occurred on habit planes made energetically favorable by the application of stress. 3 Recently, stress activation of hydride habit planes in zirconium and Zircaloy-4 was also demonstrated. The hydrides precipitated on {101l), {112l} and (2131) planes in both zirconium and Zircaloy-4; however, no platelets were found near the prism-plane positions in the Zircaloy-4 samples. Investigations at the Savannah River Laboratory, using polycrystalline Zirc_aloy-2 samples, have confirmed the (101l) and (1121) habit planes but also showed that the prism planes were active hydride habit planes. Using single-surface stereographic analysis and back-reflection Laue techniques, most of the previously reported habit planes for a zirconium were observed.4"1 and one additional plane, the (1013) plane, was noted, Table I. All the habit planes observed had the form (101l) or { 112l) indicating that these planes are the habit planes for hydride precipitation in poly-crystalline Zircaloy-2. The specimens used in these studies were cut from large-grained weld areas of seam-welded tubing and were hydrided in either a static steam autoclave at 400°C and 1500 psig or in a modified Sieverts apparatus at 400°C.

Jan 1, 1967

By H. L. Talbot, A. J. Hall, R. S. Young

A METHOD for the chemical differentiation of oxidized cobalt from sulphide cobalt in complex mine and concentrator products is of considerable interest to a number of mining companies throughout the world. At Rhokana Corporation, in Northern Rhodesia, for instance, cobalt is found chiefly in the sulphide form, as carrollite, but a cobalt oxide mineral also occurs irregularly underground, and relatively small quantities in the mill feed from time to time are difficult to detect it visually at the concentrator. The oxide cobalt is not amenable to the sulphide flotation process used at Rhokana and nearly all of it passes into the tailing. The occasional. period when high tailing losses occur with no appreciable change in the cobalt content of the mill feed has naturally been disturbing to the concentrator staff, who had no means of determining whether an influx of cobalt oxide ore or laxity on the part of the mill flotation operators were responsible for these results. A procedure for determining oxidized copper minerals, based on their solubility in dilute sulphuric acid saturated with SO2, has been used for many years in the copper industry. In the presence of cuprite the procedure fails, but otherwise it gives results quite satisfactory for control purposes. Empirical methods for determining oxidized forms of zinc and lead have been proposed, but they are generally unsatisfactory except in isolated cases of a very simple ore. No published procedure for determining oxidized forms of cobalt or similar elements has come to the authors&apos; notice. EXPERIMENTAL PROCEDURE There are obviously two alternatives in attacking a problem of this nature. One is to employ a solvent for oxide cobalt that will not dissolve cobalt sulphide. The other is, to find a substance capable of oxidizing the cobalt sulphide to sulphate, which of course is water-soluble and can then be leached from the water-insoluble oxide cobalt. A representative sample of Rhokana cobalt oxide ore was secured, ground to minus 200-mesh, and carefully rolled to furnish a standard sample for this work. The analysis of this material gave the following percentages: Co, 0.55; Cu, 1.64; Fe, 2.98; S, 0.08; SiO2, 41.42; A1203, 11.20; CaO, 13.82; MgO, 3.80. As a source of cobalt sulphide a similar large sample of carrollite was prepared, analyzing Co, 23.36 per cent; Cu, 27.32; and S, 31.13. This sample of course was not pure carrollite, but was the best obtainable in quantities sufficient for a standard intended for considerable work. It was a pure sulphide sample, microscopic examination showing only carrollite, a little bornite, and gangue, with no visible sign of oxidized ore present. A wide variety of reagents were used in an effort to selectively dissolve oxide cobalt or to oxidize sulphide cobalt to

Jan 1, 1946

By D. W. Lillie

Property changes produced by irradiation of Al-0.4 wt pet Li alloys at 270°C to a burnup of 0.155 pct of all atoms are described. Metallographic evidence of the formation of internal pores and the concentration of gases at grain boundaries is shown. Some conclusions are drawn concerning desirable property characteristics for resistance to radiation swelling. RADIATION induced gases are of great practical significance in nuclear engineering since they affect the behavior of fissionable fuels and control rod materials. In fuels the gases xenon and krypton are the major offenders, producing serious em-brittlement at low irradiation temperatures and gross swelling at high irradiation temperatures. In control rod materials containing boron, the production of helium from the B 10 (n, 0) Li7 reaction produces similar reactions. Since the trend in reactor design is for operation at increasingly high temperatures, the phenomenon of high-temperature swelling by these induced gases has been the subject of considerable recent study. The objectives of such work have been to obtain engineering information and quantitative data on the effects in specific fuels and control rods and to obtain further understanding of the mechanism of gas damage so that more intelligent corrective steps can be made. Analogue systems are often useful for the latter objective and in this case alloys containing Li are suitable in view of the reaction Li6 + n - He4 + He 4. Both products are gases and no serious radiation problem is produced to complicate post irradiation handling. Considerable caution is, of course, necessary in any operations in which tritium release is possible. The present program was initiated to provide a detailed study of the effects of He + H3 generated by irradiation in Li-bearing alloys. The results on Mg-Li solid solution alloys have been reported elsewhere.&apos; This paper presents information on irradiation of an A1-0.4 pct Li alloy in which the lithium was present as highly enriched Li6 in order to maximize the radiation burnup. PROCEDURE The original intent in the selection of the alloy content was to have Li in solid solution at all temperatures. It became apparent, however, that the solubility of Li in A1 was substantially lower than that reported in the original reference consulted.&apos; This was substantiated by the work of Nowak3 who reported solubility of less than 0.01 pct Li at 100°C. The alloy used (0.4 pct Li) was therefore two phase at room temperature. The irradiation temperature was estimated to be about 270° C, and at that temperature all or almost all of the Li would be soluble under equilibrium conditions. The precise state of the alloy under irradiation is not known. Aluminum used was 99.996 pct purity (max. impurities Si 0.002 pct, Mg 0.001 pct, Fe 0.0005 pct, and Cu 0.0005 pct). The lithium was obtained from Oak Ridge National Laboratory; 96.1 + 0.1 pct of the lithium was ~i~, but chemical impurities were 0.25 pct Ca, 0.05 pct Fe, 0.02 pct Na, 0.02 pct Cu, 0.01 pct Sr, and 0.01 pct Ba. The two metals were melted in an alumina crucible in a resistance heated furnace in an atmosphere of helium. A l-in. ingot was cast in an iron mold, machined to %-in. round, hot swaged (350°C) to 0.080-in. round, cold swaged to 0.060-in. round, and finally cold drawn to 0.040-in. round. Four-inch wire lengths were then cut and annealed at 250°C for 4 hr in helium. Irradiations were carried out in a VT hole in the Argonne CP-5 reactor. The wires were held in an aluminum jig, sixteen wires per capsule, and were maintained in a helium atmosphere for maximum heat transfer. Eight wires of pure aluminum and eight of Al-Li alloy were placed in each capsule. Argome Laboratory statements were accepted as establishing flux and exposure levels. These were based on previous experience and flux map-

Jan 1, 1961

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.&apos; &apos; The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By Pradeep K. Rohatgi, David N. French, Surendar M. Jain, Clyde M. Adams

The effect of solute concentration and diffussivity on dendritic solidification of dilute binary aqueous solutions has been investigated; chlorides of sodium, potassium, lithiurn, and hydrogen were used as solutes. Dendrite spacings were measured in spherical droplets and in unidirectionally solidified specimens. In the droplets, the freezing rate is uniform over the entire specimen and remains constant from the beginning to the end of solidification. In the unidirec-tionally frozen specimens the freezing rate varies within a given volume of liquid during the solidification cycle; in addition, it varies with location uithin the specimen. Mass transport analysis has been used to calculate the supersaturation, AC, supercooling, AT, and transcerse growth velocity, V , of ice dendrites during solidijication from the dendrite spacings measured in the droplels. The ice dendrite spacing in a given solute increases lineary with the solule concentralion at a fixed freezing rate. The ualues of AC, AT, and V increase with an increase in solule concentration. The value of AT in the aqueous solution is of the same order of magnitude as in Al-Cu alloys of the same concentration; the dendrite spacings in Al-Cu alloys also increase with an increase in solute concentralion. For the jamily of aqueozrs solulions incestigaled, the dendrite spacing increases linearly with solute diffusivity at fixed values of concertralion and freezing ,rate. The values of ?C and ?T decrease, whereas the value of V increases with an increase in solule diffusicity. The measured dendrite spacings , L, can be expressed by the relatiun: L = K;(dfa/db) 4 K2C +K3D - K4 where dfs/d? is-change in fraction solid with time (freezing rate), C is solute concentration, D is solute diffusivit K1 = (14 * 4)pmin1&apos;2, K2 = (70 ± 10) pl (moles)- K3 = (24 r 3) . l05 psec (cm)-~. K. = -132 ± 10) 1. FREEZING of solutions is almost always an ehunmix-ing" process because the composition of crystallizing solid generally differs from that of the parent liquid. " Solute concentration and transport are therefore in]portant considerations in solidification of solutions. The influence of these factors on the dendritic solutions produced from metallic solutions is of practical significance since the properties of the solid aggre-gate are often strongly influenced by dendrite spacing.&apos;&apos;&apos; Alexander and Fthines3 found that dendrite spac- ings generally increase with solute concentration in several metallic systems. Michael and Bever1 have observed an increase in a aluminum dendrite spacings in dilute A1-Cu alloys. Rohatgi and AdamsJ have reported a linear increase in a aluminum dendrite spacings with increasing copper contents up to 28 pct in A1-Cu alloys. Bolling and Tiller"&apos; have theoretically examined the effects of solute concentration and diffusivity on the growth of cells and dendrites. Their analysis of dendritic growth assumes a steady-state growth and the maximum possible velocity for dendrite propagation. In addition, the quantitative analysis is restricted to dendrites of rotational symmetry and is therefore not directly applicable to the plate-shaped dendrites of ice obtained in the present study. There are practically no experimental observations of the effect of solute diffusivity on dendrite spacings in metallic systems. The reason appears to be the lack of experimental data on solute diffusion coefficients in liquid metallic solutions. The present work is concerned with the effect of solute concentration and diffusivity on dendritic solidification of dilute aqueous solutions: the solutes examined are potassium chloride. sodium chloride, lithium chloride. and hydrogen chloride. There were several reasons for selecting these solutes. The variation of dendrite spacing with freezing rate in these solutiolls is similar to that observed in A1-Cu alloys.8 These aqueous solutions have almost identical phase diagrams at dilute concentrations. Fig. 1. and the diffusion coefficients show very little variation with solute Concentration.9,10 Dendrite spacings were measured as a function of freezing rate. solute concentration. and solute diffusivity. Dendrite spacings were measured in two different types of freezing systems. droplet and unidirectional, respectively. In the droplet freezing system

Jan 1, 1970

[ ]

Jan 1, 1938