Search Documents

Jan 1, 1967

By N. Parlee, V. C. Kashyap

The solubilities of nitrogen in liquid iron and liquid Fe-Ni, Fe-Mo, Fe-V, and Fe-Mo-V alloys were measured by the Sieverts method. Measurements were made at 1600° to 1800°C on binary alloys up to 20 pet Ni, 10 pet V, 10 pet Mo; and on ternary alloys containing 0 to 3 pet V with 0 to 5 pet Mo. The results on liquid iron confirm that Sieverts' law is obeyed in the range 50 to 750 mm pressure. The measured solubilities and their temperature coefficients are in general agreement with other modern authors. The logarithms of the activity coefficients of nitrogen in the binaries are approximately linear functions of the pet of alloying element. A method suggested by Wagner, Chipman, and others for predicting gas solubilities in complex alloys from solubility data on binaries was applied to the Fe-Mo-V alloys. Reasonably good agreement was obtained between calculated and experimental solubilities. NITROGEN'S solubility in liquid iron has been studied by a number of investigators. It is reasonably well established that the solubility of nitrogen follows Sieverts' law at least up to 1 atm partial pressure and that the solubility increases gradually with temperature. The solubility of nitrogen in Fe-X binary liquid systems has been investigated in only a few cases. Only the systems Fe-Cr,3-5, 7 Fe-V,3 Fe-Mn,3, 5 Fe-Ni,3, 5 Fe-Si,B, H Fe-C, L, H and Fe-P4 appear to have received any study. The only work on liquid Fe-V was done by Brick and Creevy.3 This was limited to 13.5 pet and 26.5 pet V, but no exact temperatures were recorded. No work whatsoever appears to have been done on liquid Fe-Mo alloys and even work on Fe-Ni alloys is rather scant. The work on liquid ternary systems is still more limited, and the only publication available appears to be that of Wentrup and Reif,7 who studied the Fe-Cr-Mn and Fe-Cr-Ni alloys. Rassbach, Saunders, and Harbrecht17 have reported work on the solubility of nitrogen in stainless steel but this was not a systematic study of any particular system. Commercial alloys usually contain several alloying elements. Thus, it often becomes important to be able to predict the nitrogen solubility in systems containing two or more added elements without the necessity of making measurements. Wagner,14 Chipman," Darken and Gurry," and Morris and Buehl 14 have suggested means by which this may be accomplished, and Langenberg14 has recently applied one of these methods to nitrogen solubility in complex liquid alloys. This paper reports the results of nitrogen solubility determinations on Fe-Ni, Fe-Mo, Fe-V, and Fe-Mo-V alloys and compares calculated and experimental solubilities in the ternary alloy. Attempted measurements on Fe-Cr alloys were not successful by the experimental method employed. Experimental Method The general method of solubility measurement was that of Sieverts.' The apparatus and procedure were essentially the same as used by Liang, Bever, and Floe."' The equipment consisted of a small vacuum furnace heated by a 6 kw induction unit, gas measuring apparatus, and a gas purification train. The crucibles used were Norton Alundum with alumina sand around them for insulation. The crucibles were charged with 100 to 200 g of material, about 180 g or nearly filling the crucible being found most satisfactory. Hot volumes were determined with argon and ranged from 95 to 130 cu cm (stp). Temperature measurements were made with a Leeds and Northrup optical pyrometer which was calibrated periodically against the melting point of iron in the same apparatus."-'* Good quality nitrogen, hydrogen, and argon gases were further purified and dried in standard purification trains. The sources of the high purity iron and other alloying elements used were as follows:

Jan 1, 1959

By M. Cross

INTRODUCTION The results of the Japanese dissective investigations have [l-4] transformed our understanding of how the blast furnace operates. These studies revealed an internal structure of the furnace burden with five main zones, as illustrated in Figure 1. In the granular zone the charged material retains its structure whereas in the cohesive zone the iron ore particles are at advanced stages of reduction and form a semi-molten mass with a relatively high flow resistance. In the active coke zone molten iron and slag flow through a matrix of loosely packed coke. The raceway is a relatively small void space generated by displacement of coke due to the hot blast momentum, whilst the hearth is packed with coke, slag and molten iron. [ ] It is now well appreciated that furnace control is largely achieved and maintained by using the burden charge distribution to determine the gas glow distribution within the furnace and, hence, the shape and extent of the cohesive zone. In fact, Wakayama et a1 [5] of Nippon Steel Corporation state that optimum furnace operation is synonomous with the formation of a desirable cohesive zone shape, which in turn is almost solely determined by the burden charge distribution and its mechanical properties [6]. Much of the development work on operating furnaces since the dissective investigations has been oriented towards the identification of external furnace measures which reliably predict the shape of the cohesive zone. Currently the most popular measures are top gas temperature, velocity and CO/CO, ratio profiles [5]. More recently pressure distributions as evaluated from a series of wall measurements down the height of the furnace are also being utilised [7] to identify the position and shape of the cohesive zone. A great deal of emphasis has been placed upon achieving a consistent quality in the burden charge materials, establishing a suitable set of operating conditions and only making changes when forced to, ie., the operation for some reason moves outside a desired operating range or the production requirements change. Operational control schemes based upon this philosophy (eg., Kawasaki's GO-STOP system [8]) have been remarkably successful at achieving both high production rates and relatively low fuel costs. Mathematical models have long been used as tools to assist in the analysis of the blast furnace process. Although, the models have been useful in post-operative analysis and for identifying trends, etc., they have not proved reliable for detailed design criteria or as the basis for effective control schemes. Such mathematical models have moved from simple statistical correlation, through overall and stagewise heat-and-mass balance calcu-

Jan 1, 1984

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 ¼ miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1938

By T. K. Smith

The comments contained in the discussion of the paper concerning the prediction of fracture gradients are of considerable interest, since the subject is of a very controversial and timely nature. It is regrettable and Fairhurst2 contradicts the author's statement in the third paragraph of Other Applications. These references create significant doubt that Eaton's Eq. 1 predicts fracture pressure during the injection of fluid into old wells. 3. No evidence is presented in this paper to support the author's Conclusions 2 and 3. While an empirical coefficient related to back-calculated field data is correlated with depth (Eaton's Fig. 4), there is no reason to suspect that this coefficient might be the Poisson's ratio of the various formations involved. 4. Until the field data supporting the empirical approach proposed by the author are presented and evaluated, the accuracy claimed in Conclusion 5 is without substantiation. References 1. Geertsma, J.: "Problems of Rock Mechanics in Petroleum Production Engineering", Proc., First Intl. Symposium on Rock Mechanics, Lisbon (1966) 585. 2. Haimson, B. and Fairhurst, C.: "Hydraulic Fracturing in Porous-Permeable Materials", I. Pet Tech. (July, 1969) 811-817. that the comments are those of a critic and do not offer an alternative and better method for the prediction of fracture gradients. Nevertheless, a reply is in order.

Jan 1, 1970

By Benjamin Smith Lyman

THE importance of topography to geology is so commonly underrated as to deserve to be pointed out again and again. The relation of topography to the different branches of geology may be seen best by a glance at them all. Geology is well understood to consist of the observation of facts about rocks as materials of the earth (geognosy), and the explanation of those facts (geognosy). The facts to observe are : I. GEOMETRICAL, as (1) structure, including the dip and strike at different points, the size, shape, and position of basins and saddles; (2) vertical section, that is, the thickness of rock groups and of their parts ; (3) horizontal or geographical position. 11. PHYSICAL, such as texture, whether sedimentary or crystalline ; and, if crystalline, whether granitic, porphyritic, amygdaloidal, globular, or concretionary ; whether compact or granular; coarse or fine; pervious or impervious; hard or soft; firm or tender; with cleavage or without ; massive or thin ; the microscopic structure ; also whether magnetic or not ; soluble or insoluble ; fusible or infusible ; and the constituent minerals. 111. CHEMICAL that is, the composition of the rocks and of their minerals and their affinities. IV. PALAENTOLOGICAL, as what kind of fossils are in the rocks,

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

By Louis A. Carapella, William E. Shaw

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

By William E. Shaw, Louis A. Carapella

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 1, 1950

By Grafton Thrasher

For the proper discussion of this subject it is necessary to incorporate in this paper the substance of part of an article published by rite in Metallurgical and Chemical Engineering for January, 1915. CAST-IRON TEST PLUG, SHOWING LOW MOTTLED AND MOTTLED FRACTURES. Several years ago, while I was thief chemist for a malleable-iron company, it occurred to me that the mere regulation of silicon was not sufficient to produce the desired degree of chill. But only after repeatedly encountering this fact in befit open-hearth and air-furnace, as well as cupola metal, was I led to regard variation in the total carbon as the principal cause of disturbance; and I resolved to determine the total carbon as well as the sill on ill every heat, and by a carefully prepared test piece to gauge the approximate degree of chill. The test piece selected was a round plug, 2 in. in diameter and 12 in. long, cast on end

Jan 10, 1915

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases.

Jan 3, 1955

Jan 1, 1968

By Jesus P. Manzano

The report of which this paper is a summary was made in 1890 for the Compania Investigadora Mexicana y Americana. Since the region examined covers 900 sq. kilom., chiefly of wooded arid rocky hills, almost without roads, and for the most part uninhabited, While the examination had to be made in two months, of which period more than 15 days were continuously rainy, I need not say that this account is not complete and thorough. I. Geography and Topography. The center of this zone, 19 kilom. SW. of San Luis Potosi, is situated in lat. 21° 24' N., and long. 2° 3' W. of Mexico City. The altitude ranges from 1866 m. (that of San Luis) to . 2816 m. (that of the Realito mountain), in the Sierra de Sail Luis. The topography is hilly—partly wooded, partly bare. The principal more level areas are the Bledos valley on the south, and portions of the haciendas of Tepetates, San Fran cisco and Santiago, on the west. The water-supply is scanty. The two streams that cross the Zone, the Santiago and Bledos rivers, carry water nearly the year through, though much reduced in the dry season. Other streams are torrents of less importance. All the waters of the valley and Sierra of Sail Luis arc absorbed or sink, not passing beyond Soledad de los Ranchos. The Continental di vide is within the Zone, some waters going west to the Pacific, others east to the Gulf of Mexico. II. Geology. Concerning the geology of this district I condense the fol lowing from the memoir, Las Minas de Guanajuato, prepared for the Minister of Fomento by Senor Pedro Lopez Monroy, mining engineer, with which I am entirely in accord. He says, ill substance:

Jan 1, 1902

By Henry M. Howe

PART I. § 1. Introduction. After giving certain definitions, this paper gives the reasons which led to Roozeboom's form of the diagram of the freezing-point curves and general equilibrium of the iron-carbon compounds, steel and cast-iron ; and then those which led to replacing it with the present or double diagram, in which graphite is at all temperatures held to be the more stable and cementite the less stable (metastable) form of carbon. Next in § 10 the evidence supporting this greater stability of graphite is examined, then in § 17 that which seems to oppose it, and in § 22 a summary of the evidence is presented. The second part of the paper considers the topography of the graphite-iron diagram, rejecting summarily the solubility-lines based on the data of Charpy and Grenet and of Mannes-mann, on the ground that the data even on their face do not really point toward these lines, and that they are wholly incompetent to determine any solubility-lines whatsoever, because they report together with the dissolved carbon also an indeterminate quantity of cement-carbon, and because even such carbon as is actually dissolved, only in part represents the solubility of graphite, and in another and indeterminate part represents the solubility of cementite, or at least of carbon in presence of cementite as distinguished from graphite. It might be thought that graphite is but slightly soluble in iron, because of the absence of any suggestions of eutectoid graphite, corresponding to the eutectoid cementite of pearlite in very many cases in which the cast-iron seems to consist of ferrite and massive graphite only, and because of the micrographs of Goerens and Gutowsky. In these the primary austenite of cast-iron quenched but little below the eutectic freezing-

Jan 7, 1908

By Ivan B. Cutler, Milton E. Wadsworth

Coprecipitation of anionic and cationic polyelectrolytes has been applied to flocculation of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves.

Aug 1, 1956

Jan 1, 1968

By G. R. Mansfield

THE geologic structure of the Idaho phosphate field has an important bearing on the classifica-tion and the exploitation of the lands that contain phosphate. Maps and structure sections1 recently made available show that the phosphate is mainly preserved in downfolded or downfaulted areas. Since the phos- phate beds are generally rather soft and lie between harder and thicker formations they have been forced to adjust themselves to these formations during epochs of disturbance of the earth's crust, so that they are frequently affected by minor folds and by faults which may help exploitation by producing undue thickness at certain places or may hinder it by cutting out the phosphate at other places where according to expecta-tion it should be present. A particularly important structural feature which affects both the distribution and the exploitation of the phosphate beds is the great Bannock overthrust by which one or more slices or blocks of the earth's crust have been pushed over other blocks like ice cakes on a pond. Thus in this region a great flap of folded rocks lies across other rock structures for a distance of approximately 35 miles. Most of the commercially accessible phosphate deposits, shown in the maps that accompany the report cited, are in this flap, which con-stitutes the upper block of the overthrust. In some places, however, the phosphate in the lower block is also accessible. In both blocks post-phosphate rocks exposed at the surface here and there indicate that phos-phate beds may lie at greater or less depth below. The presence of the Bannock overthrust beneath much of the area reported is known by the occurrence of windows in the upper block both within the quadrangles mapped and in areas farther west. The portions of the lower block exposed in these windows show stratigraphic dis-cordance with the surrounding formations. The depth of the fault plane at most places, however, can be told only by drilling or actual mining. Some of the folds in the upper block are relatively deep and it seems fairly certain that the phosphate that may originally have been present in their deeper parts has been removed by thrust faulting. The estimates of phosphate reserves in folds liable to be affected by the Bannock overthrust may therefore need ultimate revision depending on the depth of this fault plane, as it may subsequently be ascertained.

Jan 1, 1928