Search Documents

By Fred C., Fred C. Bond

Comminution energy is principally energy of deformation before breakage, which appears as heat. An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories are compared.

Jan 1, 1950

By C. A. Heiland, Tripp R. M., Dart Wantland

This paper serves to illustrate the application of geophysics to a virtually abandoned mine properly, an application that led to the discovery of an ore body and thus afforded an Opportunity to cOmpare subsequent geologic findings with geophysical data. The work herein described represents, however: more than mere ''case history." It demonstrates that it is possible to obtain satisfactory results by simple means and relatively inexpericnced personnel. The geophysical surveys were made by students as a part of their field assignments in the course of their regular training, and were supervised by Dart Wantland, J. E. Hawkins and R. Maurice 'Tripp. In the course of several seasons an appreciable amount of material was accumulated, which gave graduate students an opportunity for special studies. In this connection, the contributions by L. Massé, R. C. Hyslop, and J. E. Hawkins deserve special mention. The property owners cooperated wholeheartedly in the work, and special thanks are due messrs. J. F. Johnson and S. E. Zelenkov, of the American Smelting and Refining Co., for their interest and for permission to utilize the results of their development work for this publication. Location and Geology The Malachite mine is situated on the northcrn slope of Bear Creek Canyon, 4 miles northeast of Evergreen, I½ miles northwest of Idledale, and 4% miles west northwest of Morrison, in Jefferson County, Colorado. The location (Fig. I) is north of the center of set. 30, T. 45, R. 70 W., at an elevation of about 7500 ft, above sea level, Near the mine the terrain slopes rather uniformly southward at an angle of about 180 pigs. 3 and 7). The geology of the Malachite mine area has been described by J, underhill,' W, Lindgren,2 and J. Boyd.3,4 A map showing surface outcrops and mine workings appears in Fig, 2. the Malachite mine is in an amphibolite belt enclosed in gneisses and schists of the Idaho-Springs formation (probably early Algonkian age). The highly contorted beds are nearly vertical and strike slightly north of west. A series of granite-pegmatite dikes have been intruded almost at right angles into the gneisses and schists and doubtedless are postmineral. While most of the formations are exposed at the surface, a part of the 'lope is covered by slide rock and float, and in the eastern portion by alluvium and creek fill. A quartz-diorite dike cuts through the amphibolite schists at a small angle with nearly vertical dip. The copper sulphides, developed in this dike by magmatic segregation, occur in lenticular form. As far as the mine workings have revealed, the ore lenses are often discontinuous in depth and

Jan 1, 1946

By Tripp R. M., C. A. Heiland, Dart Wantland

This paper serves to illustrate the application of geophysics to a virtually abandoned mine properly, an application that led to the discovery of an ore body and thus afforded an Opportunity to cOmpare subsequent geologic findings with geophysical data. The work herein described represents, however: more than mere ''case history." It demonstrates that it is possible to obtain satisfactory results by simple means and relatively inexpericnced personnel. The geophysical surveys were made by students as a part of their field assignments in the course of their regular training, and were supervised by Dart Wantland, J. E. Hawkins and R. Maurice 'Tripp. In the course of several seasons an appreciable amount of material was accumulated, which gave graduate students an opportunity for special studies. In this connection, the contributions by L. Massé, R. C. Hyslop, and J. E. Hawkins deserve special mention. The property owners cooperated wholeheartedly in the work, and special thanks are due messrs. J. F. Johnson and S. E. Zelenkov, of the American Smelting and Refining Co., for their interest and for permission to utilize the results of their development work for this publication. Location and Geology The Malachite mine is situated on the northcrn slope of Bear Creek Canyon, 4 miles northeast of Evergreen, I½ miles northwest of Idledale, and 4% miles west northwest of Morrison, in Jefferson County, Colorado. The location (Fig. I) is north of the center of set. 30, T. 45, R. 70 W., at an elevation of about 7500 ft, above sea level, Near the mine the terrain slopes rather uniformly southward at an angle of about 180 pigs. 3 and 7). The geology of the Malachite mine area has been described by J, underhill,' W, Lindgren,2 and J. Boyd.3,4 A map showing surface outcrops and mine workings appears in Fig, 2. the Malachite mine is in an amphibolite belt enclosed in gneisses and schists of the Idaho-Springs formation (probably early Algonkian age). The highly contorted beds are nearly vertical and strike slightly north of west. A series of granite-pegmatite dikes have been intruded almost at right angles into the gneisses and schists and doubtedless are postmineral. While most of the formations are exposed at the surface, a part of the 'lope is covered by slide rock and float, and in the eastern portion by alluvium and creek fill. A quartz-diorite dike cuts through the amphibolite schists at a small angle with nearly vertical dip. The copper sulphides, developed in this dike by magmatic segregation, occur in lenticular form. As far as the mine workings have revealed, the ore lenses are often discontinuous in depth and

Jan 1, 1946

By L. Zwell, H. A. Wriedt

X-ray Lattice parameter and bulk density measurements were made at room temperature on solid solutions of nitrogen in purified a, iron, containing from 0 to 0.053 wt pct N. When nitrogen is dissolved in a, iron, the fractional increase in unit cell volume (X-ray diffraction) and the fractional increase in volume per gram of iron (bulk density measurement) are the same within experimental error. The two sets of results when averaged show that the unit cell edge of a, iron increases linearly by 3.2 X 10-2 A per wt pct N dissolved and that the partial gram-atomic volume of nitrogen at infinite dilution in a, iron is the same as it is in nitrogen-martensite, that is, 5.90 cm3. RECENT reviews17' of literature dealing with the lattice parameter of ferritic iron-nitrogen alloys indicate that the dilating effect of dissolved nitrogen on the bcc unit cell of a iron is not known with confidence. Five investigations3-7 either revealed no effect of nitrogen or were inconclusive. Among other investigations, where quantitative data were obtained, the results of Osawa and Iwaizumi8 indicate too large an effect, and those of Eisenhut and Kaupp9 show the lattice parameter of ferrite varying with the nitrogen content at concentrations far beyond the known solubility limit. It is not clear in Burns'10 data what value should be used for the lattice parameter of nitrogen-free ferrite in calculating the dilation. Burdese11 shares with Burns the shortcoming that the iron-nitrogen alloys were solution-treated and quenched with undissolved nitride present. The consequence is that the un- certainties in the solubility limit1 are added to those in the lattice parameter measurements when the variation of lattice parameter with nitrogen content is computed. For a system of such widespread interest, we felt that a new investigation was merited. Both X-ray diffraction and bulk density measurements were used to determine the dilation of the , a iron lattice by dissolved nitrogen. EXPERIMENTAL PROCEDURE Material. The bulk density and X-ray diffraction experiments were both made with specimens of a purified iron (denoted as "B iron")- from Battelle Memorial Institute. The impurity contents were as follows: As, C, Cu and Pb—50 ppm; Ag, Al, Co, Ga, 0, Ti-11 to 50 ppm; B, Be, Ca, Cd, Cr, Mg, Mn, Mo, N, Ni, S, Sb, Si, Sn, V, W-10 ppm or less. The vacuum-cast ingot was hot-forged and annealed. Pieces of the forged stock were machined and cold-rolled to give strip stock 0.08 and 0.002 in. thick for density and for X-ray measurements, respectively. Preparation of Specimens. Starting with a piece of the cold-rolled iron stock, the general sequence of operations, after an initial recrystallizing anneal, was to measure the density or lattice parameter, nitrogenize, remeasure the property, age or denitrogenize, and again measure the property. Duplicate analyses for nitrogen were made by a modified Kjeldahl method on portions of the actual density specimens and on pieces nitrogenized to equilibrium alongside the X-ray specimens. Annealing of the density specimens was performed by sealing the pieces with the as-rolled surfaces removed by filing into evacuated "Vycor" capsules and treating for 1 hr at 750°C followed by furnace cooling. (TO check the effect, if any, of annealing procedure, a specimen also was

Jan 1, 1962

By J. F. Kemp

PAGE Introduction,............170 I. The Competence oF the Igneous Rocks to Supply the Materi als oF Veins,...........171 The Demonstrated Presence of the Metals in the Igneous Rocks,. . 171 The Presence of the Metals in the Sedimentary and Metamorphic Rocks, 173 Conclusions,...........175 The Abundance in Igneous Racks of Vapors or Dissociated Gases which will Yield Water on Emission and Cooling,. 175 The Sequence of Eruptions,. .. . 1 . • .. 78 The Sequence of Vein-Formations,.......1 79 Contact-Metamorphism,.........180 Pegmatites,............181 Frequency of Pneumatolitic Minerals in Veins,.. 183 Surface-Flows of Igneous Rock Unfavorable to Vein-Formation,. . 183

Jan 1, 1902

By J. J. Egan, A. B. Kinzel

Much work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it constitutes the main action in the usual steelmaking processes. A. L. Feild' has formulated a basic differential equation expressing the open-hearth reactions and Herty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action to the reaction FeO + C + CO + Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Beild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X lop2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order-to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By Sven Fornander

An account is given of the way in which a new process for desulphurization of hot metal is carried out at a Swedish blastfurnace plant. In the process powdered burnt lime is used as a desulphurizing agent in a rotary furnace. Results are given. IN a paper by Kalling et al.* the fundamentals of a new process for desulphurization of hot metal using powdered burnt lime as a desulphurizing agent were outlined. The purpose of the present paper is to give a brief account of the way in which this process is being carried out in practice by Surahammars Bruks AB, Sweden, and of the results obtained. + The hot metal from the blast furnace is tapped into a ladle of 15 tons capacity and transferred to a rotary furnace, a simplified drawing of which is given in Fig. 1. The rotary furnace has a total length of about 160 in. and an outside diameter of the rings of about 130 in. The furnace is in a horizontal position, with its rings placed on four rollers, and can be rotated by a driving mechanism at various speeds of up to 34 rpm. The rotary furnace and its driving mechanism were designed and constructed at Surahammar. The hot metal is charged into the rotary furnace through the opening to the left in Fig. 1. See Fig. 2. An addition is then made to the furnace consisting of finely ground burnt lime amounting to 2 pct of the weight of the hot metal as well as 0.5 pct of coke breeze. After the additions are made, the furnace is sealed to the atmosphere by means of two lids and set in rotary motion at a rate of 34 rpm. The sulphur in the hot metal is rapidly absorbed by the lime added, the time of treatment needed is normally 30 min. The process is then stopped, the lid is removed, and the furnace is lifted up by a crane and used as a tilting ladle for pouring the metal into the pig-iron molds, Fig. 3. Process Metallurgy The hot metal charged into the rotary furnace has a composition which usually lies within the following limits: C, 3.70 to 4.10 pct; Si, 0.80 to 1.80; Mn, 0.40 to 0.80; P, 0.025 to 0.030; and S, 0.060 to 0.200. Figs. 4 and 5 give examples of the changes in hot metal composition taking place during the treatment in the rotary furnace. As will be seen from the diagrams, the sulphur content of the metal decreases very rapidly during the first 10 min of treatment from about 0.100 to about 0.020 pct S. During the following 20 min, the sulphur content goes down slowly to about 0.005 pct S. The carbon and silicon contents of the metal decrease by about 0.10 pct each during the treatment. The manganese and phosphorus contents remain unchanged. Thus, if the process is started with an iron of the composition given above, the finishing composition of the metal usually lies within the following limits: C, 3.60 to 4.00 pct; Si, 0.70 to 1.70; Mn, 0.40 to 0.80; P, 0.025 to 0.030; and S, 0.002 to 0.020. The chemical reaction taking place during the process can be written:

Jan 1, 1952

By A. F. Andresen

IN the course of another investigation the lattice parameters were determined for a series of compositions of tin in copper. Ten-gram samples of the alloys were made from spectroscopically pure tin and copper. The metals were weighed and placed in graphite capsules (previously fired at 5500°F) which were then sealed individually in evacuated vycor tubes. The tubes were mounted on a spit, transverse to its axis, which continually rotated the melts in a furnace. After homogenizing, filings were made of one third of each slug by filing off a complete cross section. A 325-mesh sieve was used to obtain the powder for the X-ray determination. The sieved powders were annealed in vacuo at 600°C for 24 hr to remove the cold work, and then quenched. The lattice parameters were determined with a flat-plate back-reflection camera using CuKa radiation (A., = 1.5405A, A,? = - 1.5443A). With this radiation the (331) and (420) reflections appeared close to the focusing region. As reference lines were used the same reflections from pure copper powder, between which the (420) lines of all these alloys are situated. The variation of the systematic error over this angular range was found to be less than the estimated experimental error ±0.0005A which is indicated in Fig. 1 for all but the sample with 8 pct Sn. As a check some of the powders also were examined in a regular Debye-Scherrer camera with the Straumanis film mounting. The parameters were here evaluated by extrapolation against cos2? to ?= 90o. The results are shown in Fig. 1 where the lattice parameters in Angstrom units are plotted as a function of weight percent of tin. The reflection lines for the 8 pct alloy were not clear at first, perhaps due to coring. Several measurements were made after different annealing programs on two separate

Jan 1, 1959

By A. B. Kinzel

MUCH work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. . This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it con-stitutes the main action in the usual steelmaking processes. A. L. Feild1 has formulated a basic differential equation expressing the open-hearth reactions and Hefty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action. to the reaction FeO +C ?? CO +Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed' constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Feild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X 10-2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By Northcutt Ely, Charles F. Wheatley

This chapter deals with the systems of laws by which governments regulate the exploration for and production of the minerals within their jurisdictions. It is a summary, restricted by necessary space limitations, of material assembled by the author for a forthcoming publication of the United States Bureau of Mines, "Summary of Mining and Petroleum Laws of the World." (Information Circular, 1959.) The present study is organized in three parts, dealing with (1) the historical background of these legal systems, (2) laws of the United States, and (3) laws of other countries of the world. The reader's attention is invited to the acknowledgments at the end of the chapter, which inadequately express the appreciation due those who have assisted in the collection of this material. Part I. Historical Development of Major Western Systems of Land Tenancy with Respect to the Ownership and Control of Minerals The use of metals in primitive societies was largely confined to the manufacture of weapons for self-preservation. The ruler's control over copper, then brass, then iron, was essential to maintenance of his own ascendancy at home and his group's position against neighbors who had access to similar metals. Ancient societies were thus characterized by the ruling group's ownership of minerals and metals. The Egyptian civilization, which emerged in the fourth millenium B.C. upon the agricultural subjugation of the lower valley of the Nile, was responsible for extensive development of the upper valley as a source of mineral wealth. The production of gold during the height of that civilization has been estimated at $30,000,000 per year, thus equaling the early placers of California and Australia. The mines of Egypt were the property of the Pharaohs and were controlled at their direction. Greek mining developed a different scheme of land tenancy which more closely resembled modem concepts. Development of mineral resources was

Jan 1, 1959

By G. St. J. Perrott

During the past year, the Bureau of Mines has carried on an investigation of liquid-oxygen explosives (L.O.X.) to supplement the work described in previous publications.' The present paper gives results of the first part of this work, which was a laboratory investigation of the properties of typical combustibles used in L.O.X., and the relation of these properties to the absorption and retention of oxygen by the explosives and their explosive characteristics. No attempt will be made to describe the development of liquid-oxygen explosives, because this phase of the subject has been well covered.2 The L.O.X. cartridge consists of a paper wrapper filled with an absorbent combustible material that is saturated with liquid oxygen by soaking it therein. After saturation, the cartridge is removed from the liquid and fired with fuse and cap, or electric detonator, in a manner similar to other explosives. Certain types of cartridge may be detonated with fuse alone, requiring no cap to initiate the detonation. ' By suitable variation of the nature and density of the combustible, cartridges having a wide variety of explosive characteristics may be made.

Jan 1, 1925

By E. Miller, J. M. Eldridge, K. L. Komarek

The thermodynamic properties of liquid Mg-Ge alloys have been determined between 1000°and 1500°K by an isopiestic method. Germanium specimens, heated in a temperature gradient and contained in covered graphite crucibles of special geometry, were equilibrated with magrtesium vapor in closed titanium tubes. The crucible design allowed free access of magnesium vapor to the samples during the equilibration to form alloys of magnesium and germanium, but prevented magnesium losses from the crucibles on quenching the titaniuin tubes to terminate the experimental runs, thus preserving the equilibrium alloy compositions. The activities and partial molar enthalpies of magnesium and the integral thermodynamic properties of the system were calculated from the experimental data. THE Mg-Ge phase diagram' shows one congruent melting compound, Mg2Ge, of essentially stoichio-metric composition, two eutectics, and very limited terminal solid solubilities. Very little information is available on the thermodynamic properties of the Mg-Ge system. The free energy of formation of Mg,Ge was recently deter-mined2 by a Knudsen cell technique in the temperature range 610° to 760°C. The standard enthalpy of formation of Mg,Ge was measured calorimetrically by Bever and coworkers.3 The present study was undertaken as part of a general investigation of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,4 Mg-Sn,5 Mg-Ge, and Mg-Si. An isopiestic technique was used which was developed by the authors5 for investigating the thermodynamic properties of liquid Mg-Sn alloys. Specimens of the nonvolatile component, contained in covered graphite crucibles, are heated in a temperature gradient in an evacuated and sealed titanium reaction tube, and equilibrated with magnesium vapor of known pressure. The method employs crucibles of special geometry which preserve the high-temperature equilibrium composition of liquid alloys having a highly volatile component such as magnesium on termination of the experimental runs by quenching the crucibles to room temperature. EXPERIMENTAL PROCEDURE First reduction germanium of 99.999+ pct purity (Eagle-Pitcher Co., Cincinnati, Ohio) and 99.99+ pct magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) were used. The graphite crucibles were machined from high-density (1.92 g per cu cm) graphite rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The non-reactivity of graphite with germanium at the temperatures used in this study had been previously established by Scace and Sleck.6 The experimental procedure has been previously described in detail.5 The selection of a particular crucible geometry for a run was determined by a combination of imposed experimental conditions, the principle being that more tightly covered crucibles were required to preserve alloy compositions during quenching when higher magnesium pressures and higher specimen temperatures were used. Depending upon the composition range of the equilibrated alloys the source of the magnesium vapor was either pure magnesium or a two-phase mixture of Mg2Ge + Ge-rich liquid of known magnesium pressure. The experimental runs can be divided into the following three groups on the basis of crucible geometry and magnesium source material. Crucibles with Small Holes and Pure Magnesium Reservoirs. The crucible dimensions were identical to those of the Mg-Sn investigation5 except that the hole diameters were reduced to 0.010 in. because of the higher temperatures and higher magnesium pressures involved in the Mg-Ge system. During an equilibration run, magnesium vapor diffused from the reservoir to each specimen through the small holes, one drilled through the crucible lid and two others drilled through graphite baffles positioned vertically inside the crucible between the lid hole and the specimen. Since the magnesium pressure was high, i.e., in the range 117 to 277 Torr, during the equilibration time of approximately 24 hr, equilibration was not impeded by these holes. A specimen composition at equilibrium was fixed by the relative temperatures of the specimen and the reservoir, and by the thermodynamic properties of the system. Upon brine quenching the titanium reaction tube to end a run the vapor pressure of magnesium above the liquid alloys decreased exponentially with decreasing temperature, and the small cross-sectional areas of the holes (4.9 x 10"* sq cm) drastically reduced magnesium losses from the crucibles. Because of its low vapor pressure, germanium losses from crucibles during a run were at most 0.2 mg for pure germanium and correspondingly less for the alloys. This crucible geometry satisfactorily retained the equilibrium alloy compositions on quenching for magnesium-rich (from 3 to 33 at. pct Ge) alloys provided their temperatures were below the melting

Jan 1, 1967

By H. C. Chao, L. H. Van Vlack

Small MnS inclusions with known crystallographic orientations were placed inside powder compacts of low-carbon steel. After the metal was axially campressed with negligible end friction, the deformstions for the metal and the inclusions were compared. The MnS inclusions deformed more when the [100] direction was aligned with the compression axis than when the [111] direction was parallel to this axis. The deformations of the inclusions in the two principal radial directions were equal for each of the above orientations. Inclusions with [110] compression alignments did not deform with radial symmetry. The relative deformation of the inclusion and metal was closely dependent upon the relatiue hardness of the two phases. The relative deformation of the two phases was not sensitive to the rate of deformation. RECENT studies by the authors1.&apos; suggested that the plastic deformation of MnS in steel would probably be highly sensitive to the orientation of the inclusions and to the temperature of the metal. This paper reports an investigation of these factors upon MnS behavior within steel. Manganese sulfide (MnS) possesses an NaCl-type structure and typically has extensive (l10) {110} slip as a separate (noninclusion) crystal.&apos; A secondary slip system, ( l 10) { l l l}, has also been observed where the major slip system is restricted. In general, MnS inclusions must be rated as a highly deformable second phase.3 The amount of sulfide deformation varies, however, with several composition and processing factors. Some of these have been only partially assigned. For example, it is known that minor amounts (<0.01 pct) of silicon within free-machining steels will increase the amount of MnS deformation,4 but the mechanism of the added deformation can only be surmised at the present. Manganese sulfide and steel have sufficiently comparable deformation characteristics so that slip which is started in steel may be continued through the sulfide inclusions and back into the steel if the crystal orientations are favorable.5 A more detailed discussion of previous work on the plastic deformation of NaC1-type crystals and on the plastic deformation of inclusions within a metal is given in Chao&apos;s work.6 EXPERIMENTAL PROCEDURE The manganese sulfide which was used in this study was prepared by previously described methods.&apos; Single crystals of MnS, both as cleavage cubes and as spheres, were oriented within steel powder compacts so that the desired crystal directions were parallel to the direction of axial compression. A four-stage hydrostatic compaction procedure was used and involved the following steps. In the first stage part of the powder was placed in a metal die 1 in. in diameter with a thick (1 in. OD, 5/8 in. ID) rubber liner which had one end plugged. The steel powder was hand-rammed, making it as dense as possible before placing a carefully sized MnS crystal (either as a sphere or as a cube) near the center. The crystal was oriented with the chosen direction vertical; viz., [001], [011], or [111], with the aid of a X10 microscope. A pair of tungsten wire threads 0.020 in. in diameter was inserted along the side of this (&apos;core compact" to locate the desired plane after the compression tests. After the crystal was positioned in the center of the die, more powder was added and carefully rammed by hand. The die was then capped with a rubber plug of the same hardness and thickness as that of the liner. The whole assembly as shown in Fig. 1 was compacted by a ram load of 54,000 lb (about 70,000 psi). In the second stage a smaller, 3/4-in, rubber-lined die was used to give a stress of approximately 120,000 psi. The above process was repeated with the initial compact serving as a core for a larger compact. The final product after sintering was a cylinder 1 cm long and 1 cm in diameter, having a density of 7.54 g per cu cm. This was close to the theoretical density since the metal contained a non-metallic phase. There was no evidence of MnS deformation during the hydrostatic compaction or subsequent sintering. Elevated-temperature hardness data were obtained by procedures previously described.2 Compression tests for inclusion deformation utilized the cylinders which were described above. The critical problem in these tests was the lubri-

Jan 1, 1965

By H. C. Chang, N. J. Grant

REEP studies and measurements in most in-V> stances are based on a relatively gross gage length. Even in some recent theoretical studies on the mechanism of creep, changes were followed by means of X-rays and metallography without regard for the behavior of the individual grains and grain boundaries.&apos;" Analytical studies of creep have frequently indicated that more than one competing process is operative and that the ultimate creep performance depends on the effects of temperature, time, and strain rate as well as grain size.&apos;-" he grains and grain boundaries are known to respond differently to these variables but the extent of the response is still little known, especially in poly-crystalline materials where the relative orientations of grains and grain boundaries are important. This paper reports some experimental observations of the behavior of the grain boundaries and their effect on the deformation in the grains. High purity aluminum was used to avoid complications of aging reactions, second phase, inclusions, etc. Experimental Procedure A small vertical nichrome wound furnace was built to permit direct loading on the test specimen. This furnace is capable of operating up to about 1300°F with reasonable temperature distribution. A ground rectangular quartz window, 1.25x0.5 in., is imbedded in the external stainless steel tube to permit observations of the creep process with a microscope. An argon atmosphere ,was provided to prevent oxidation. The quartz window caused a temperature gradient between the back and front surfaces of the specimen of 15" at 700°F. The temperature gradient could be cut down to 3°F along the length of the specimen by adjusting shunts across the furnace windings. An ordinary metallurgical microscope with a working distance of 14 mm was rebuilt so that it could be moved in three mutual perpendicular directions. Visual examination could be made with either a 30X eyepiece or a 15X filar eyepiece. Using an objective of focal length 24.3 mm and a numerical aperture 0.20 a total magnification of 120X or 240X could be obtained. High purity aluminum rated at 99.995 pct was supplied by the Aluminum Co. of America as % in. then the gage portion was further machined to 3/16 in. diam. The ends were Y4 in. diam and threaded to fit available specimen holders. Two opposite flat surfaces of the gage portion were obtained by milling, giving final dimensions of the gage portion of 3/4x3/16x3/32 in. Machined specimens were first electropolished in Jacquet&apos;s solution.&apos; Reference marks were produced by pressing a thin sewing needle into the surface of the specimen. The specimen was then annealed at 900°F for 24 hr and at 1150°F for 12 hr. Typical macrostructures of specimens treated in this manner are shown in Fig. 1. The range of the grain size was 1 to 5.5 mm (see Fig. l), but most of the grains were of 2.5 mm and went through the whole thickness of the specimen. The specimen was re-electropolished and etched electrolytically to reveal the grain boundaries. In order to reveal the orientation difference of the grains, etch pits were produced on the surface of the grains by etching in a mixture of hydrochloric and nitric acids (HC1, 45 pct; HNO,, 10 pct; H,O, 45 , by volume). The specimens were very carefully put into the holders and furnace; yet even with this care, fine slip lines were developed on the specimen surface.

Jan 1, 1953

By Henry S. Burnholz, Charles Y. Clayton, Francis B. Foley

This work was first undertaken for the U. S. Bureau of Mines, in 1919-20, by C. E. Julihn, superintendent of the station at Minneapolis. Learning of the interest, in this subject, of B. F. Tillson, of the New Jersey Zinc Co., Mr. Julihn and Mr. Foley went to Franklin, N. J., and discussed the matter with him. A conference in Chicago, in November, 1920, was attended by Dr. F. G. Cottrell, who was then Director of the Bureau of Mines, and representatives of the Bureau of Mines and of the hlissouri School of Mines and Metallurgy; at this time a cooperative plan of work was agreed upon by the Bureau of Mines and the Missouri School of Mines. In February, 1921, Mr. &apos;Tillson arranged a conference on this subject at the time of the annual meeting of the American Institute of Mining and Metallurgical Engineers, at which several technical papers were presented. In a paper, the Breakage and Heat Treatment of Hock Drill Stcels, he suggested a program that might be carried out in connection with the investigation of the problem. At this conference Mr. Manning, former Director of the Bureau of Mines, suggested the formation of an advisory committee to the Bureaus of Mines and of Standards for prosecution of this investigation. On Feb. 20, 1922, a secoud conference in New York, at the time of the annual meeting of the American Institute of mlining and Metallurgical Engineers, was attended by representatives of various technical societies. At this meeting, the report of Nov. 20, 1921, of the Chiefs of Divisions of Metallurgy of the Bureaus of Mines and of Standards, was discussed and it was agreed: 1. That the survey recommended by the two bureaus should be undertaken, which survey would have for its object the ascertaining of the present status of the practice of the heat treatment of drill steels, the extent to which the breakage occurs, etc.; and 2. That a report should be presented, of the findings of those who made the survey, to the Advisory Board to the Bureaus of Mines and of Standards. The Bureau of Standards assigned $4000 to the prosecution 01 a three-months&apos; survey, which was carried out in April, May, and June, 1922, of about sixty mines

Jan 1, 1923

By Charles Y. Clayton, Henry S. Burnholz, Francis B. Foley

This work was first undertaken for the U. S. Bureau of Mines, in 1919-20, by C. E. Julihn, superintendent of the station at Minneapolis. Learning of the interest, in this subject, of B. F. Tillson, of the New Jersey Zinc Co., Mr. Julihn and Mr. Foley went to Franklin, N. J., and discussed the matter with him. A conference in Chicago, in November, 1920, was attended by Dr. F. G. Cottrell, who was then Director of the Bureau of Mines, and representatives of the Bureau of Mines and of the hlissouri School of Mines and Metallurgy; at this time a cooperative plan of work was agreed upon by the Bureau of Mines and the Missouri School of Mines. In February, 1921, Mr. &apos;Tillson arranged a conference on this subject at the time of the annual meeting of the American Institute of Mining and Metallurgical Engineers, at which several technical papers were presented. In a paper, the Breakage and Heat Treatment of Hock Drill Stcels, he suggested a program that might be carried out in connection with the investigation of the problem. At this conference Mr. Manning, former Director of the Bureau of Mines, suggested the formation of an advisory committee to the Bureaus of Mines and of Standards for prosecution of this investigation. On Feb. 20, 1922, a secoud conference in New York, at the time of the annual meeting of the American Institute of mlining and Metallurgical Engineers, was attended by representatives of various technical societies. At this meeting, the report of Nov. 20, 1921, of the Chiefs of Divisions of Metallurgy of the Bureaus of Mines and of Standards, was discussed and it was agreed: 1. That the survey recommended by the two bureaus should be undertaken, which survey would have for its object the ascertaining of the present status of the practice of the heat treatment of drill steels, the extent to which the breakage occurs, etc.; and 2. That a report should be presented, of the findings of those who made the survey, to the Advisory Board to the Bureaus of Mines and of Standards. The Bureau of Standards assigned $4000 to the prosecution 01 a three-months&apos; survey, which was carried out in April, May, and June, 1922, of about sixty mines

Jan 1, 1923

By H. R. Ogden

The notch sensitivity of titanium alloys is affected by impurity content, microstructure, and heat treatment. Using notch tensile properties to evaluate notch sensitivity, three commercial titanium-base alloys were investigated over the temperature range of -320o to 390°F. The alloys studied were Ti-5Al-2.5Sn, Ti-6Al-4V, and Ti-2Fe-2Cr-2Mo. Six interstitial levels were studied for each alloy in four mi-crostmctural conditions. The ff- 0 alloys were studied in both the annealed and heat-treated condition. All tests were conducted using 1/4-in. diam round tensile samples. The notched samples had a 50 pct notch with a notch sharpness (a/r) of 53, corresponding to Kt 6.3. Notch sensitivity was increased by increased interstitial content, low temperature, and acicular-type microstructures. The heat-treated, high-interstitial content - 13 alloys were more notch sensitive than the same alloys in the annealed condition. In addition, minima in the notch tensile-temperature curves were observed at temperatures near 32°F. These minima became more pronounced with increasing interstitial content. 1 HE increaseduse of titanium alloys in high strength applications at subzero temperatures requires that a better under standing of the low-temperature behavior of the alloys be obtained. At low temperatures, metals generally exhibit increased strength with lowered ductility and tohness. Notch sensitivity and the factors which influence it become more important as the strength level is increased and the temperature is decreased. Some of the factor s which affect notch sensitivity in ti- tanium alloys are composition, interstitial content, microstructure, and heat-treatment condition. In this paper, the results of a study of these variables on the notch sensitivity of three titanium alloys at temperatures from —320o to 390o are reported. The notch geometry selected for this program was chosen to provide a severe test of notch sensitivity. The ability of the metal to flow without initiating fracture under these severe conditions is reflected in the notch-strength values. Since notch strength is, in part, determined by the constraint exerted by the combined tensile stresses, the behavior of notch specimens reflects the properties of the material under combined stresses. For example, a material with a high notch-unnotch strength ratio may be expected to withstand the biaxial stresses encountered in a pressure vessel better than a material with a low ratio of notch-unnotch strengths. This implies that maximum strength alone is not a sufficient criterion for applications of this type. It further may be concluded that the various conditions that promote poor notch behavior also will affect adversely the performance of materials under combined stresses. In the alloys studied, these included low temperatures, high interstitial levels, and hasformed microstructures. EXPERIMENTAL PROCEDURES Three alloys, Ti-5Al-2.5Sn, Ti-6Al-4V, and Ti-2Fe-2Cr-2Mo, were purchased from commercial producers as 2-in.-dam rod stock. Oxygen and nitrogen were added to these alloys by remelting to obtain a variety of interstitial contents as shown in Table I. In order to Compensate for the much more potent strengthening effect of nitrogen compared with oxygen, an oxygen equivalent content is used to describe the total oxygen plus nitrogen contents studied. It has been suggested previously1 thatnitro-gen is approximately twice as effective in strengthening as oxygen, and carbon, to the extent it is in so-

Jan 1, 1962

By Charles S. Barrett, Robert F. Mehl, Shueling Woo

WHEN one solid phase is generated from another, fixed and rational orientation relationships are observed to subsist between the parent and the new crystal. The principle has been proposed&apos; that the relationships obtaining between the same two phases are identical whatever the type of phase change involved, or whichever of the phases may act as parent. Many types of phase changes have been studied: allotropic transformations in pure metals, precipitation from solid solutions, eutectoid decompositions, peritectic reactions, the formation of oxide layers, and others.2 Phase layers generated by diffusion of one metal into another constitute an additional type of reaction. This report provides new data on the orientation relationships occurring between , phase layers formed by diffusion, in the Cu-Zn system, § and furnishes further evidence in support of the principle. MATERIALS AND METHODS The Cu-Zn system is especially suitable for these studies since the high vapor pressure of Zn provides an opportunity readily to create one phase poorer in Zn upon a parent phase richer in Zn by removing Zn by vaporization, or to reverse this process by adding Zn from Zn vapor; e.g., the beta phase can be found as a layer upon gamma by dezincing, or gamma can be found on beta by addition of Zn from Zn vapor. Since orientation relationships are to be sought, requiring crystals large enough for orientation determinations, it is convenient to prepare single crystals or large grains of the parent phase. The samples were prepared from oxygen-free high-conductivity copper and Horse Head zinc by melting under a borax flux in a graphite crucible. Large crystals of beta brass were grown by the strain-anneal method, in plates sectioned from the cast ingots, by the following procedure. Rockwell-hardness indents were made at I cm. intervals-and with various loads, then the plates were annealed for .4 days at 700°C. in Nichrome boxes packed with beta-brass chips and graphite. Surface layers were removed by grinding and etching to a depth of about 1.0 mm., and individual grains were cut out. Crystals of alpha and gamma brass were prepared by freezing, by lowering a graphite crucible at speeds less than one inch per hour through a furnace held at a constant temperature above the melting point. Single crystals were cut out with a jeweler&apos;s saw, ground, polished and etched. Care was taken to remove cold worked layers from the finished crystals

Jan 1, 1944

By G. A. Moore, D. W. Williams, C. E. Sims

During the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging, The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary ab- normal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders&apos; Society of America has, since Nov. I, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. &apos;The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.&apos; Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period of approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the System could be degassed thoroughly in

Jan 1, 1949

By C. E. Sims, G. A. Moore, D. W. Williams

During the past several years the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture and the ductility values often can be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging, The cure of such an abnormal condition represents a real improvement in the quality of the steel. Some hundreds of previous investigations, largely qualitative in nature, have established beyond reasonable doubt that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary ab- normal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, the Steel Founders&apos; Society of America has, since Nov. I, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. In order that these investigations might proceed on a quantitative basis, hydrogen analyses of a precision considerably higher than any previously reported in the literature were necessary. &apos;The method chosen was selected entirely on the basis that it had the highest probability of freedom from uncontrollable errors and will be described in detail in another publication.&apos; Briefly, the method used consisted of the hot extraction of solid pieces of steel weighing from 45 to 50 g in a highly evacuated quartz tube maintained at 1050°C (1925°F) for a period of approximately 40 hr. The greatest precautions were taken to eliminate blanks and insure a sound gas-collection system. vacuum and temperature conditions were maintained automatically. Mercury-filled risers were used for the introduction of samples in order that the System could be degassed thoroughly in

Jan 1, 1949