Search Documents

By F. Louis Grammer

The difference between blast-furnace gas and ordinary producer-gas is chiefly that blast-furnace ga,s is higher in CO2 and lower in hydrocprbons and hydrogen, as is shown in Table I. Table I.— Volume-Composition of Producer-Gas and Blast-Furnace Gas. Producer-Gas. Blast-Furnace Gas. Per Cent. Per Cent. (Volume.) (Volume.) CO......22 to 33 25.5 CO2........ 6 to 3 13.0 H...13 to 7 1.5 CH4........ 3 to 1.5 0.0 N..54 to 60 60.0 If natural gas, water-gas, or by-product coke-oven gas be available, blast-furnace gas can be made to resemble very closely in calorific value the average producer-gas by merely mixing in one of these products, which are richer in hydrocarbons and hydrogen. Blast-furnace gas, however, possesses a virtue which is sometimes absent in producer-gas, especially with coals very high in sulphur—namely, that blast-furnace gas is relatively free from sulphur. In some regions the sulphur in coal is an acute problem, and it is highly desirable to find uses for the mine-products which are specially high in sulphur-content. An advantage would be gained if the coal were coked before charging into the gas-producers, but this adds to the expense. Sulphur may be partly eliminated from coal by washing it, the success depending upon the form in which the sulphur occurs, and upon the efficiency of the washer, but it cannot always be removed to the extent desired at most American plants. It is not practicable to remove all the sulphur from producer-gas by washing it, though Mr. Reinhardt, of Germany,

Jan 1, 1909

By R. H. Richards

In October, 1891,I read a paper before the Institute on a "A HandTelescope for Stadia-Work" (Bans., xx., 732), and promised to report at an early date some results showing the degree of accuracy attained with the instrument. I am now able to report on these results and also on certain improvements that I have made in the target since the first paper was read. I may say that I prefer the title, "Prismatic Stadia-Telescope," to that used in my earlier paper, for while the instrument can be used with perfect satisfaction for short sights up to, say, 300 to 600 feet when held in the hand, it is impossible to read milch longer distances without the use of a tripod, as a steady support for the instrument. Results are here given upon four combinations of prism and telescope. No. 1. A telescope made by Alvan Clark & Sons, 3-inch objective, 28 inches focal length, magnifying 60 diameters, the prism covering half the objective: Feet measured Reading of Distance reduced Reeding of rod pro by tape. the rod. to feet. portional to 100 ft. 127.66 1.1825 100 .92629 211.35 1.9585 100 .92666 326.59 3.0265 100 .92669 484.88 4.4925 100 ,92652 606.91 5.6225 100 .92641 Average,,92651 The value of this prism therefore is .92651 feet on the rod for 100 feet of distance, or 1 foot on the rod corresponds to 107.931 feet of distance. No. 2. A Bardou telescope having a 1-inch objective, magnifying 20 diameters, and a prism covering half the objective:

Jan 1, 1893

By W. C. Schafer

In tunneling or mining where hydraulic shields, moles, or rock boring equipment is used lasers such as those shown guide the production machine by providing a continuous and visible line and grade reference. In this application the laser may be mounted in the heading, preferably somewhere above spring line. If we view the circular heading as a compass in the vertical plane with 0º referencing at the crown of the heading and 180º on the invert, then it might be said that the laser may be mounted anywhere from 270º through 0º to 90º. The laser is generally mounted 2 to 3 ft off the wall or the crown of the heading by means of a bracket that may be attached directly to the liner plate. In cases where no liner plate is used, then brackets may be bolted directly into the ribs, or grouted directly into the rock. Once the laser is in position the beam is projected to the face. Two points must be surveyed upstream between the laser and the face which define line and grade. Targets may be suspended beneath each of these points approximately 2 to 3 ft. These targets may be circular or rectangular with a surface area which approximates 16 sq in. Each of these two targets should have a ½ to ¾ in. hole drilled directly in their center. When the laser is adjusted so that the beam passes through the holes in each of the two targets, the laser beam itself will parallel the center line of the tunnel and become a visible line and grade reference over the total beam projection.

Jan 1, 1970

By M. F. Fogler

An attempt to duplicate Rawdon and Mutchler's experiments showing a reversal of hardness with continued rolling gave negative results, indicating that the phenomenon is not general but depends, probably, on local conditions of rolling. IN A recent paper, Rawdon and Mutchler1 gave some exceptionally interesting results on the Brinell and scratch hardness of severely cold-worked metals. In their work, they found that, on continued cold rolling, the metal hardened up to a particular point and then reversed and became softer; this was true for both Brinell and scratch hardness values. The generally reported behavior2 of metals, with respect to Brinell tests on cold-worked material, is that the metals harden up to a certain point and then, on further cold rolling, no change in Brinell hardness occurs. Jeffries and Archer3 state that there is little difference between the scratch hardness of annealed and cold-worked metals; the work of Faust and Tammann4 also indicated no difference between-the hardness of annealed and cold-worked copper. Rawdon and Mutchler found, when they plotted the reduction ratio (initial thickness divided by thickness after rolling) against the hardness value for the cold-rolled material, that the hardness number increased up to a reduction ratio of about 3 and then decreased and became even smaller than that for the annealed metal. This behavior was reported for both scratch and Brinell hardness; Figs. 1 and 2 show their results for Brinell hardness on the metals for which they published data. This is an exceptionally interesting phenomenon, if it occurs under all conditions of rolling, and would have an important bearing on the practice of cold

Jan 1, 1925

By Bernard G. Carbajal

The dielectric properties and thermal stability of glow-discharge polytnerized films of styrene, chloro-benzene, and other organics and photoresist filrns are presented. Variations in the glow-discharge polymerization procedure are related to thermal stability. Thermal treatwzents to improve the dielectric properties of both positive (A2 340) and negative (KMER) photoresists are given. THIS study of the dielectric properties of thin organic polymer films is part of a program to investigate the electronic applications of organic materials. Thin organic polymer films have been produced in an ac glow discharge,13 with a low-energy electron-beam process,4 and in an rf dicharge. A process has been developed during the course of this program for forming thin organic polymer films in a dc glow discharge. These glow-discharge polymerized (GDP) films exhibit some useful dielectric and insulative properties. Variations in the properties of the GDP films can be induced by changes in the source material (monomer) andor in the conditions of the glow discharge. Thin organic polymer films can also be produced from typical positive and negative photoresists. Some variations in the properties of the photoresist films can be induced by suitable post-application treatments such as thermal crosslinking. The properties of interest in this study are dielectric constant, dielectric strength, resistivity, and thermal stability. POLYMER FILM PREPARATION I) GDP Films. The GDP films were prepared in a dc glow discharge in an atmosphere of organic monomer vapor. The details of the glow-discharge procedure have been presented previously.6 Briefly, under the influence of a dc glow discharge organic vapors can be polymerized in the vapor phase and the resultant polymer (GDP film) deposits on and in the vicinity of the cathode. Substrates placed behind a screen cathode can be uniformly coated over all exposed areas. Pattern definition can be achieved using normal mask stencil techniques. Table I presents the pertinent parameters in the preparation of GDP styrene. Conditions of Forrrzation of GDP Styrene. The rate of deposition for GDP films was monitored using a current-time integrator. The thickness of the deposited film for a given set of experimental conditions was a function of the current-time integral. The fifth row in Table I is a compilation of the deposition rate of GDP styrene films. Other organic monomers behave in a similar fashion. With the exception of the highly halogenated saturated hydrocarbons, all organics subjected to the conditions of the glow discharge form GDP films. 11) Photoresist Films. Photoresists are normally recognized to exist in two forms, a low molecular weight, soluble polymer form (A) and a high molecular weight, crosslinked insoluble form (B). Typical negative photoresists are applied in the low molecular weight form A and converted to the high molecular weight form B by the action of light. (Positive photoresists are applied in form B and converted to form A by the action of light.) Eastman Kodak Metal Etch Resist (KMER) has been chosen as a typical negative photoresist. Polymer film samples were prepared in the same configuration used for GDP films. The KMER was applied in the usual fashion using a 120°C drying step (infrared-lamp heating) and a 180°C post-bake. Care must be taken to completely remove the solvent in the drying step and to properly develop and postbake to exposed photoresist. If the photoresist film is not properly dried and postbaked, severe blistering and peeling will occur during subsequent elevated-temperature exposure. Thickness can be controlled by varying the viscosity of the form A photoresist and the spin rate at application. AZ 340 was chosen as a typical positive photore-

Jan 1, 1967

By Michael A. Gustafson, Fernando B. Sotelino

INTRODUCTION The degree of success of any new project will ultimately depend on two factors: (i) the underlying economic strength of the project; and (ii) how successfully the parties involved can coordinate their interests to establish a financing structure which indeed capitalizes on the project's inherent economic attractiveness. A project's underlying economic attractiveness is determined by its inherent comparative advantage in accessing the factors of production, combining these factors of production to create a product and marketing this product. Initially, the decision regarding whether to go ahead with the project - the go/no go decision - has to be based on its total ability to generate cash flow returns to project participants to compensate them for resources committed and risks undertaken. The extent to which project sponsors will actually benefit from the project's inherent economic attractiveness is fundamentally dependent on their ability to establish the long-term financing arrangement which best meets the objectives and constraints of each project participant and sources the most advantageous funding. The decision regarding the financing of the project, the "how-to-go" decision, is then an attempt to find the capital structure, consistent with market terms and conditions and sound financial management policies which will best: (i) match planned outflows with cash inflows; and (ii) maximize the return for project sponsors. This article makes use of a case study to illustrate the analytical process involved in dealing with the go/no go and the how-to-go decisions on a project. Though most commonly applied to project finance situations, the guideline described herein is equally applicable to other financing situations, such as leveraged buyouts and debt restructurings, where timely repayment of debt depends largely on the future cash flows to be generated by the entity being financed. Our case study is of a hypothetical expansion of an existing copper mining operation in Latin America. The company, Latin American Copper (LAC) currently has 147 million metric tons of proven sulphide ore reserves. The existing mine complex consists of an open pit mining operation and a conventional flotation plant with a processing capacity of 20,000 metric tons of ore per day. LAC sells copper concentrates primarily to Japanese custom smelters. The mine has been in operation for 5 years, fine copper production last year was 108,240 metric tons, and LAC currently has assets of $175 million and net worth of $135 million. Due to a recent increase in proven reserves, LAC is considering doubling the treatment capacity of its flotation plant to 40,000 tons per day, and expanding its mining capacity to meet the additional concentrator capacity (the "Project"). Project capital expenditures and incremental working capital have been estimated at approximately $210 million. The construction period is expected to cover one year, including a three-month start-up phase. The Project is to be funded by a combination of equity, senior debt, including both supplier credits and/or commercial bank term loans, and subordinated debt. LAC's shareholders are willing to commit a maximum of $50 million to the Project. A government development agency, which is also a minority shareholder, might be willing to lend approximately $40 million to LAC in the form of subordinated notes, depending on the ability of the Project to generate foreign exchange reserves. Commercial banks cannot be expected to offer loans with maturities longer than ten years. The Project is expected to increase the value of the firm because: (i) It will solidify the Company's position as a low-cost copper producer by taking advantage of economies of scale. As a result of the expansion, cash production costs are expected to decrease 7.0[c]/lb. and all-in costs 11.0[c]/lb; (ii) The potential earnings stream from the sulphide ore reserves will be realized

Jan 1, 1985

By J. J. Becker

BEAN1 has discussed the magnetic behavior of mixtures of small ferromagnetic particles on the order of 20 to l000A in diam. As he points out, there are three size categories with characteristic properties: 1) Particles large enough to contain many ferromagnetic domains magnetize initially by the motion of domain walls. The initial susceptibility of such particles, if domain-wall motion is assumed to be perfectly easy, depends only on their shape. It is equal to the reciprocal of the demagnetizing factor (and is thus 3/4 tt for a sphere) and is independent of temperature. 2) Smaller particles find it energetically undesirable to contain domain boundaries. They are always spontaneously saturated, and reverse their magnetization only by rotation of their entire magnetic moment. As assemblage of such particles has a remanence which is a large fraction of the saturation of the assemblage; its coercive force is on the order of 2K/1,, where K indicates magnetic aniso-tropy from any source, and I, is the saturation magnetization of the substance of which the particles are made. 3) Particles which are still smaller continue to be single-domain, but the direction of their magnetization fluctuates thermally, as first pointed out by Neel.' They have no remanence and no coercive force and possess the temperature-dependent magnetization curve of a paramagnetic substance with a very large moment. Bean calls this superpara-magnetism. All of these kinds of behavior are observable in alloys consisting of a precipitate of ferromagnetic phase in a nonferromagnetic matrix. Fig. 1 shows a typical aging curve for the room temperature coercive force of a sample of 98 pct Cu-2 pct Co alloy

Jan 1, 1958

By Norman L. Newbern, Robert E. Green

An investigation of the effect of size on the deformation properties of metal single crystals made it desirable to grow from the melt cylindrical aluminum single crystals possessing exactly the same crystallographic orientation but varying in diameter. Methods for the growth of rather large (up to 3 in. diam) aluminum single crystals in molds of the desired shape are well known. However, when one applies the same techniques to the growth of smaller (less than 1/8-in. diam) specimens many additional problems arise. Two of the major problems are the construction of the molds to be used and the removal of the thin specimens from these molds without deformation after growth has been completed. Also the problem of the constraint forces exerted by the mold on the specimen is much more pronounced for the smaller specimens. The technique described herein is a zone-melting method in which no mold is used since the surface tension of the molten metal and its oxide is sufficient to retain the melt. The specimen is suspended vertically in a manner similar to that of Keck and Golay.2 However, while Keck and Golay supported the specimen from both ends, the method used here supports the specimen only at the upper end. The surface tension of the molten aluminum and aluminum oxide contains the melt and suspends a length of newly grown crystal that has already passed through the molten zone until the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together in the molten region. When the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together the specimen pulls in two in the molten zone. The length of crystal which can be grown before this separation occurs varies with the diameter of the specimen and the size of the molten zone. In order to prevent the specimen from pulling in two a tube of glycerine is placed beneath the furnace in such a manner that the newly grown crystal passes into the glycerine which provides sufficient buoyancy to allow aluminum single crystals in wire form to be grown to lengths determined only by the length of the tube containing the glycerine. A schematic diagram of the experimental arrangement is shown in Fig. 1. The furnace used is constructed as follows. High-resistance nichrome wire is coiled on a 3/8-in. diam fused quartz tube. The distance between the windings is much less over a length of about 3/8 in. at the center so as to develop a hot spot. This core is located in the center of a 4-in. diam steel cylinder 5 in. in height and insulated from it by Kayolite. The temperature of the furnace is controlled by means of a thermocouple located near the central hot spot and a Minneapolis-Honeywell temperature controller. Temperature ins,ide the furnace is measured with a thermocouple and a standard potentiometer in the usual manner. By the above method it is possible to grow high-purity (99.99 pct Al) aluminum single-crystal wires over a range of sizes. Crystals varying from 1/8 to 1/64-in. diam were grown by the authors. Since the tube containing the glycerine cannot contain a crystal longer than approximately 3 ft, the growth of crystals longer than this presents another problem. It was found that one could cut the newly grown crystal without deformation in the region between furnace and glycerine tube try means of a cutting torch and then by moving the glycerine tube slightly aside continue

Jan 1, 1962

By Paul Billingsley, Augustus Locke

The mining districts of the first order' of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of compressive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 Nature of the Thrust Arc The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The. cross-sections are as shown in Fig. 2. The backbone of the belt is the upward and eastward moving block represented by the Glacier Park, the Wasatch, and the Virgin mountains, successively. The structure represented on these sections is the culmination of events which began far back in geologic time and throughout which a contrast has existed between the regions east and west of the backbone line. Before the Pennsylvanian, as Fig. 3 shows, there was a shallow shelf on the east and a deep marine trough on the west; after

Jan 1, 1935

By Paul Billingsley, Augustus Locke

The mining districts of the first order' of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of compressive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 Nature of the Thrust Arc The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The. cross-sections are as shown in Fig. 2. The backbone of the belt is the upward and eastward moving block represented by the Glacier Park, the Wasatch, and the Virgin mountains, successively. The structure represented on these sections is the culmination of events which began far back in geologic time and throughout which a contrast has existed between the regions east and west of the backbone line. Before the Pennsylvanian, as Fig. 3 shows, there was a shallow shelf on the east and a deep marine trough on the west; after

Jan 1, 1935

The mining districts of the first order' of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of compressive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 Nature of the Thrust Arc The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The. cross-sections are as shown in Fig. 2. The backbone of the belt is the upward and eastward moving block represented by the Glacier Park, the Wasatch, and the Virgin mountains, successively. The structure represented on these sections is the culmination of events which began far back in geologic time and throughout which a contrast has existed between the regions east and west of the backbone line. Before the Pennsylvanian, as Fig. 3 shows, there was a shallow shelf on the east and a deep marine trough on the west; after

Jan 1, 1935

By Augustus Locke, Paul Billingsley

The mining districts of the first order' of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of compressive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 Nature of the Thrust Arc The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The. cross-sections are as shown in Fig. 2. The backbone of the belt is the upward and eastward moving block represented by the Glacier Park, the Wasatch, and the Virgin mountains, successively. The structure represented on these sections is the culmination of events which began far back in geologic time and throughout which a contrast has existed between the regions east and west of the backbone line. Before the Pennsylvanian, as Fig. 3 shows, there was a shallow shelf on the east and a deep marine trough on the west; after

Jan 1, 1935

By W. Rostoker, H. Nichols

It has been demonstrated in previous work1'2 that wetting of aluminum alloys by liquid mercury can cause fracture to occur with substantial suppression of prior plastic flow. This has been interpreted as the action of a critical liquid species in reducing the cohesive strength of a stressed solid at sites of potential crack nucleation. In this way the critical transverse stress for fracture nucleation is reached at much lower stresses than is normally the case. The stresses for both fracture nucleation and fracture propagation are depressed by the same mechanism. In so doing the plastic-energy component of fracture energy is reduced to a level which is of the same order of magnitude as the surface, interfacial, or cleavage energy. Recent work2 has illustrated the influence of dispersed precipitates, cold work, and combinations of these on brittle fracture associated with plastic strains of the microyield order of magnitude. This has been rationalized in terms of the contribution of internal microstress fields to the stress magnifications at points of obstruction of active slip bands in a stressed metal. The presently reported studies on an Al-4-1/2 pct Mg alloy amplify this subject by introducing thermal-mechanical conditions which can produce strain aging. As amply demonstrated by Phillips, Swain, and borall, the tensile behavior of aluminum alloys containing magnesium reveals a yield-point elongation and successive discontinuous elongations over the whole plastic-strain range. This gives a stepped or serrated character to the stress-strain diagram. The yield-point elongation is not temperature-dependent. On the other hand, the discontinuous extensions in the plastic-strain range are gradually suppressed by lower temperatures of testing. At -78"C, only the yield-point elongation persists. The yield-point elongation itself can be suppressed by rapid quenching to room temperature from an annealing temperature of 500°C. The argument presented by Phillips et 1. and Cottre114 is that the yield-point elongation derives from surmounting at a critical stress the restraint to slip by grain boundaries which have been reinforced by appreciable magnesium-atom segregation. The serrated character of the plastic-strain range is the result of rapid strain aging during the test. This is made possible by the inevitable proximity of magnesium atoms to any dislocation line. In the Al-4-1/2 pct Mg alloy there is one magnesium atom for every twenty-two aluminum atoms and, with a coordination number of 12, a magnesium atom is on the average only about two atomic distances from any given lattice site. Rapid strain aging is therefore a reasonable expectation. A study of mercury embrittlement of the Al-4-1/2 pct Mg alloy (commercial designation 5083) provides an opportunity to relate the interplay of grain size, grain boundary restraint to slip and strain aging in the brittle-fracture process. One lot of commercial sheet material of 0.125-in. thickness was used for all of the tests. The specimen shape and test procedures used were the same as those described in a previous publication.2 A range of grain sizes between 0.0057 and 0.0125 mm was produced by various combinations of plastic prestrain and annealing. The coarsest grain was somewhat elongated in shape. In this case the measurement was taken in the direction transverse to the axis of tension as more meaningful to a brittle-fracture process. In the annealed condition, specimens wetted with mercury failed with zero permanent elongation at stresses slightly below the normal yield point, i.e., stresses at 0.05 to 0.2 pct strain. Since this occurs before yield-point elongation can begin, fracture derives from slip contained within individual grains and restrained from propagating across grain boundaries. No significant difference in wetted fracture stress was observed between specimens which had been water-quenched or furnace-cooled from the annealing temperatures. This signifies that the degree of magnesium segregation at grain boundaries

Jan 1, 1964

By Leo L. Van Sambeek

An understanding of the creep and yield behavior of salt is required for the rock mechanics design aspects of solution mining. Most previous studies of salt behavior have been performed on small specimens of salt under homogeneous stress conditions; i.e., uniaxial and triaxial tests on specimens <0.002 m3. The corejacking test is a larger scale test (-0.75 m3) with inhomogeneous stress conditions that provides data on the structural response of salt. Interpretation of the responses from eight such corejacking tests provides verification of the requisite constitutive parameters required to predict salt behavior at different levels of stress and temperature. These constitutive parameters are not those studied in the usual laboratory test. Corejacking test results show almost inseparable elastic and plastic closures simultaneous with the corejack pressurization. Very rapid closure (on a relative basis) continues for a period of time after the pressurization. This rapid closure is shown to be both continuing yield deformation and creep deformation. After the period of rapid closure, the closure rate approaches a constant value. Numerical modeling of the corejack tests using a creep law containing both transient and steady-state creep functions does not provide results that agree with the responses measured in the corejack tests. Using an experimental design technique plus additional numerical modeling that includes yielding of the salt, results in identification of the significant parameters which allow agreement. The significance of the results from the study is demonstrated by comparing the postulated stability and creep response of a solution-mined cavern using the previous understanding of salt behavior and the understanding developed from this study.

Jan 1, 1985

By Howard Drullard

To OBTAIN the best results from hammer drills, close attention must be paid to two factors in drill maintenance, which are of equal importance; one is lubrication, the other is the shank. With the exception of stoping drills, most modern rock drills require both oil and grease. The oil ports are in the lubricator, on or behind the hammer cylinder; the grease port for the lubrication of the &apos;chuck sleeve and rotating mechanism is on the chuck end. Ordinary machine oil is not, adapted to rock drills; a heavier more gelatinous oil such as castor machine oil or liquid-grease should be used. The lubricators should be filled-once for every 12 or 14 ft. (3.5 to 4m.), of hole drilled. Grease-guns should be used to fill the port in the chuck end once a shift; a medium ( No. 3) grease is well adapted to this purpose. Hard grease must not be put into- the lubricators, as it will not flow through that part. Contrary to the popular belief, oiling a machine once or twice a shift does not provide sufficient lubrication; the drills should be oiled once for every 12 or 14 ft. of, hole drilled. The rotating handle of a stoping drill -is an oil reservoir and is provided with a port for oiling. The rotating handle is packed with wicking, or similar material, which causes the oil to feed slowly from the handle to the other parts of the machine. Stoping drills require oil at. least twice a shift; lighter oils than castor, such as Arctic Ammonia may be used.

Jan 8, 1920

By F. E. Crane, J. Downie

The general application of Darcy&apos;s law to natural rocks has already been challenged in the literature.1 The evidence shows that the permeability as calculated from the Darcy equation can be a function of the pressure drop and the salt concentration of the water phase. Most explanations for aberrant behavior involve clays and their properties and have been qualitatively satisfactory.Recently, however, Odeh2 revived the theoretical views of Yuster.3 Since Yuster&apos;s concept implies a fundamental error in using Darcy&apos;s relationship for two-phase flow, and not merely that conditions may limit its use, Odeh&apos;s experimental support arouses considerable interest. However, Odeh&apos;s work as presented is thought to to be inadequate. He has omitted important information about his materials and procedures; therefore, acceptance of his conclusions should be withheld. Since a clay effect is possible, Odeh should have been allowed space to present a more detailed account of the rocks which he used and the precautions which he took to avoid confounding the effects of clay and fluid circulation. In addition, it follows from Odeh&apos;s discussion that the oil relative permeability should increase as the viscosity ratio increases. Odeh presents data corroborating this deduction. It also follows that the oil relative permeability should decrease as the viscosity ratio of oil to water decreases. However, our results show that a high relative permeability, when once attained by using a viscous oil, may be maintained when that oil is replaced by an oil of much lower viscosity. EXPERIMENTAL PROCEDURE The results are shown in Fig. 1 and were obtained as follows. Sandstone cores. 3-in. long X l-in, in diameter and which contained clays, were saturated with

By Colin C. Rae

The absence of paraffin and other oil hydrocarbons in the soil although they are concentrated in extensive deposits in some localities, the common distribution of plant remains through many formations that are not productive for oil, and many other factors, seem to indicate the existence of an intermediate organic compound between the complex plant compounds and the petroleum hydrocarbons; and much evidence points to the humus acids or associated organic compounds, which are probably collected by surface waters and concentrated in certain areas by means of precipitation by electrolytes, which would be contained in sea water or possibly in various inland seas or lakes. Present-day Evidence There are many present-day evidences of the association of petroleum with humus acids. Binney, in 1912, made observations without explanations on the peat mosses of Down Holland, England, where he found petroleum being formed by decomposition in the presence of an infiltration of sea water. The analysis of a typical peat will show its relationship to the humus acids under consideration. Sample No. 1, SamplE No. 2. PXr Cent. PER CENt. Water......................... 20.0 29.6 Ash.......................... 3.0 3.05 Fiber.......................... 47.0 54.95 Humus acids................ 30.0 12.50 J. D. Haseman and others have noted the association of asphalt and hydrocarbons with the swampy, boggy areas, particularly adjacent to the sea. Many of the rivers carry much humus acid in solution, and some tropical rivers carry in the aggregate millions of tons of humus each year. The amount of humus is a variable factor, depending on climatic conditions, and on the salts and alkalies present in the water, also on the density and temperature.

Jan 1, 1923

By Colin C. Rae

The absence of paraffin and other oil hydrocarbons in the soil although they are concentrated in extensive deposits in some localities, the common distribution of plant remains through many formations that are not productive for oil, and many other factors, seem to indicate the existence of an intermediate organic compound between the complex plant compounds and the petroleum hydrocarbons; and much evidence points to the humus acids or associated organic compounds, which are probably collected by surface waters and concentrated in certain areas by means of precipitation by electrolytes, which would be contained in sea water or possibly in various inland seas or lakes. Present-day Evidence There are many present-day evidences of the association of petroleum with humus acids. Binney, in 1912, made observations without explanations on the peat mosses of Down Holland, England, where he found petroleum being formed by decomposition in the presence of an infiltration of sea water. The analysis of a typical peat will show its relationship to the humus acids under consideration. Sample No. 1, SamplE No. 2. PXr Cent. PER CENt. Water......................... 20.0 29.6 Ash.......................... 3.0 3.05 Fiber.......................... 47.0 54.95 Humus acids................ 30.0 12.50 J. D. Haseman and others have noted the association of asphalt and hydrocarbons with the swampy, boggy areas, particularly adjacent to the sea. Many of the rivers carry much humus acid in solution, and some tropical rivers carry in the aggregate millions of tons of humus each year. The amount of humus is a variable factor, depending on climatic conditions, and on the salts and alkalies present in the water, also on the density and temperature.

Jan 1, 1923

By Orville R. Lyons

CENTRIFUGAL force has been utilized for the dewatering of fine coal for over 50 years by means of machines commonly called centrifugal dryers. In any centrifuge the coal and water are subjected to a spinning action which usually inctedtocreases in intensity as the coal progresses through the machine. This spinning action, or the centrifugal force that it induces, tears water away from coal particles and produces a dewatered coal. The effectiveness of the dewatering action for any particular machine is governed by the size-consist of the coal and the centrifugal force imparted to the water on the coal. Four makes of centrifuge are currently being used to dewater fine bituminous coal in the United States. These include the vertical, basket-screen C.M.I. (Centrifugal and Mechanical Industries) Carpenter, Reineveld, and the horizontal solid-bowl Bird. The C.M.I. and Reineveld centrifuges are similar in construction and are variations of the Elmore centrifuge, varying principally in the slope of the basket, operating speed, size of perforations in the basket, and diameter of the basket. The same operating description suffices for both. These centrifuges are made up of two rotating elements, an outside conical screen frame and an inside solid cone which carries spiral pusher blades. The screen frame is supported by a hollow shaft, and the solid cone by a spindle shaft passing through the hollow shaft. Both the screen frame and the solid cone rotate at high speeds; the solid cone, with its scraping flights, rotating somewhat more slowly than the screen. The wet coal enters the machine at the top, falls on the cone, and is thrown against the screen by centrifugal force. The coal slides down the screen until it meets the upper end of the flights, where it is moved slowly along the flights until discharged at the bottom. The elfluent passes through the sieve basket or screen and discharges into a launder. The Carpenter centrifuge consists of a conical rotating element with a vertical axis, built up of three rows of perforated stainless-steel plates or stainless-steel wedge-wire or round-wire sections cut and rolled to conform to the surface of the cone. Wet material is delivered to a conical hopper inside the centrifuge casing and is distributed in a thin, even layer over the inner surface of the cone by a disk mounted on the rotor shaft. Impacting of the coal against the screen and the centrifugal force exerted as the material moves downwards creates a dewatering effect. The moisture is forced through the coal bed and then through the perforated plates of the basket, collecting in a circular trough built into the centrifuge. The effluent is conducted from the trough through the centrifuge casing by outlet pipes. The dewatered coal is discharged over the inside bottom edge of the rotor. The Bird centrifuge consists of a tank or truncated conical shell, which is revolved at the desired speed by means of a drive sheave. A screw conveyor rotates inside the cone or bowl at a slightly lower speed in the same direction of rotation. The feed entrance, in the center of the large end of the truncated cone, is high enough to allow formation of a pool of slurry. Adjustable effluent-discharge ports are located in the large end of the bowl so the level of the liquid can be regulated. The solids are moved forward by the screw conveyor as fast as deposited and carried above the level of the pool for an interval before leaving the bowl. In the past these four makes of centrifuge could be compared only by indirect means. The author published a rough comparison method in 1949&apos; but

Jan 1, 1952

By Henry Lewelling

An experimental investigation of the relative effectiveness of standard bullets and "shaped charges" in perforating dense, hard formations is reported. A method is described which simulates the conditions under which a shot is normally fired. Results are evaluated on the basis of depth of penetration, extent 01 Fracturing. extent and nature of formation damage, and other physical characteristics. INTRODUCTION A study was made of the relative merits of bullets and "shaped charges&apos;&apos; as applied to well completions in hard, dense formations such as those encountered in the Permian Basin. The planning of the laboratory program stipulated that core samples should be prepared and mounted in such a way that perforation shots of either kind"" could be fired into them, keeping the factors pertinent to good shooting practice similar to what they would be in a well. The shooting was done in a buried tank. with the sample and shooting equipment covered with water. The depth of water was calculated to he sufficient to simulate the inertial effects of well fluids for the duration of an explosion (a few micro-seconds). Flow measurements were attempted on the specimens after perforation. Due to the lack of uniformity of the limestone, shale breaks. etc., these measurements proved to be of little value to the study. The mounting materials were removed. so that the character of the penetration. fracturing, etc., could be observed. METHOD Laboratory samples were selected from the hard. dolomitic sand cores from Block 31 Field. Core pieces having a 3 3/4 in. diameter and a useful length of 10 to 12 in. were used. Selection was aimed at those pieces having a minimum of shale streaks and other irregularities. The ends were cut off square Manuscript received in the Petroleum Branch office June 28, 1951. Paper presented at the Petroleum Branch Fall Meeting in Oklahoma City, Okla., Oct. 3-5, 1951. with the diamond saw. Prior to lbeing mounted. the cores were soaked in water to prevent them from absorbing water out of the wet concrete, thus weakening it. A set of steel capsules was fabricated for holding the core Samples. Seven-in. casing was cut in two-ft lengths. of which one end was closed by "orange-peeling" and welding, and the other was threaded to accept a standard bull plug. The bull plugs were fitted with copper tube connections .so that pressure could be applied when the capsules were made up. The cores were mounted in the capsules by means of wire centralizers whose function was to hold the Core in proper position while concrete was poured and set. A special aggregate was prepared wing a graded sand and gravel mixture

Jan 1, 1952