Search Documents

By Richard A. Conkling

D. W. OHERN, Oklahoma, Okla. (communication to the Secretary*). -The author states: "A shale layer buried beneath 2,000 or 3,000 ft. of strata, in some instances, will upon folding become thicker in the synclines and thinner on top of the anticlines." In any series of folded strata there is a level of no strain. Provided the strata do not slip on each other, there would be above this level a thickening of strata in the synclines and a thinning on the anticlines, as the author states, while the converse would obtain below this level. In order that the author's

Jan 3, 1917

By H. W. Mead, C. E. Birchenall

SELF-DIFFUSION of cobalt has been investigated by Ruder and Birchenall,1, 2 Nix and Jaumot,3 and Gruzin.4 The results for a given tem- perature differ by a factor of about six in the extreme cases with no really close agreement between any two sets of data. The first two groups of investigators employed the decrease of surface activity method. Since Ruder and Birchenall have shown that the values obtained from this method are sensitive to the surface preparation, it seemed desirable to perform a few check experiments by a method not open to this objection.

Jan 1, 1956

Discussion of the paper of C. W. Goodale and J. H. Klepinger, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 50, August, 1913, pp. 1935 to 2010. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa.:-Mr. Chairman, I would like to call attention to one valuable feature of the paper which may interest some: I have worked a good deal with the Pitot tube, and have always had difficulty with what is called the static end of that apparatus, so much so that I became almost hopeless of securing good results with it. I find here, however, what is stated to be a perfectly satisfactory static end for the Pitot tube, satis factory under probably all conditions. I congratulate Mr. Klepinger on the design of that tube and the consequent improvement he has made in the technical measurement of the volumes of gases. I would also like to ask if the total volume coming out of the chimney per day could not be computed by chemical analyses of the SO and SO2 in the gases, and calculation on the basis of the known weight of.. sulphur going out in a day; so that the Pitot tube measurements . could be checked by a method independent of measurements in the flues. J. H. KLEPINGER :-I think the volume of gases could be determined in that way. Those of a chemical turn of mind would go. about it so, but I am not enough of a chemist to follow that method, and consequently I always look at the mechanical way to obtain the results.

Jan 11, 1913

The paragraphs quoted, regarding Mr. Hoover's appointment as chairman of the newly organized food board of the United States, are taken from the editorial page, of the New York Times for April 13: ?The country is fortunate in commanding the services of Herbert C. Hoover as Chairman of the newly established Food Board. This is n, problem of first importance. Few realize the extent to which American food stuffs will enter into the decision of the war, and it is doubtful if it has occurred to many minds as yet that we shall have to deny ourselves what we have regarded as necessaries in order to keep our European allies supplied. " Mr. Hoover is one of the leading mining engineers of the country. At the outbreak of the war he put his private affairs aside to become the head of the American Commission for Relief in Belgium. He has had an experience that perhaps no other man has ever had, covering the raising of money and the purchase and distribution of supplies on a large scale; He has been brought into close relations with the neutrals and the belligerents on both sides. By them all he is recognized is one of the best executives brought to the fore by the mar. Mr. Hoover is in a position now to place abilities and experience at the service of his country. He will come back with comparative data that will enable him to measure resources and deficiencies accurately. This appointment gives renewed assurance of our Government's grasp of the problems of war and its resolve to apply, business principles to their solution."

Jan 5, 1917

By A. Werenfels

No PETROLEUM, in commercial quantities, is found in France except the small production of the Pechelbronn field (Fig. 1) in Alsace, which produced 75,000 tons in 1923; therefore the test of the petroleum prospects of the Limagne is most interesting. Under the superintendence of M. Termier, chief engineer of the French mines, a well near Crouelle (Fig. 2) was drilled in 1921 to a depth of 856.3 m. (2808 ft.); at different depths favorable showings were encountered. The well, however, was abandoned because of drilling difficulties. A second one is now being drilled near the same place.

Jan 1, 1925

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham, Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

Manganese nodules are essentially a surficial resource-there are four times as many nodules on the surface of the deep ocean floor as in the next 3 ft of underlying sediment. Target mine sites in the North Pacific occur in water 12,000 to 18,000 ft deep. The mining technique is comprised of four major factors: the mining device, lifting method, surface vessel, and ore transport. Certain deep-ocean mining proposals are revolutionary in character. Current research has tended to construct simple but flexible devices to work at the great depths and corrosive environments of the deep-ocean floor

Jan 4, 1975

A self-appointed, committee consisting of J. Waldo Smith, Chairman, Richard S. Buck, J. J. Carty, J. Parke Channing, E. L. Corthell, Alfred Craven, Thomas Crimmins, Gano Dunn, George Gibbs, Alex. C. Humphreys, F. L. Hutchinson, Charles Warren Hunt, D. S. Jacobus, John W. Lieb, William Barclay Parsons, George H. Pegram, Charles F. Rand, Calvin W. Rice, Robert Ridgway, William L. Saunders, Merritt H. Smith, Bradley Stoughton, and William H. Wiley, organized a course of seven free lectures on military engineering, which were given by Captains Thomas M. Robins, Richard T. Coiner, Edward D. Ardery, Corps of Engineers, United States Army, and which was under direction of Major General Leonard Wood. The United Engineering Society presented, without charge, the use of the auditorium for the purpose of these lectures, but the interest proved to be more than three times as much as had been expected, and it was therefore necessary to divide the courses into three parts, one of which was given in the afternoon in the auditorium of the United Engineering Societies Building, one in the evening in the same place, and another in the evening in the auditorium of, the American Society of Civil Engineers. These lectures occurred on Mondays, from Feb. 14 to Mar. 27, 1916. The subjects and speakers were as follows: Feb. 14, 1916: Organization and Duties of Engineers in War, and what Engineers in Civil Life will be called upon to do in the Defence Of the United States. Captain Thomas M. Robins, Corps of Engineers. Feb. 21, 1916: The Service of Reconnaissance Including Surveying, Mapping and Sketching, Photography and Map Reproduction. Captain Richard T. Coiner.

Jan 5, 1916

By Alexander L. Holley

IN order to put sufficient work on steel ingots for rails, they must be reduced from about 12 inches square. As this cannot be done at one heat, they are first drawn down to about 7 inches square, and then reheated and rolled into rails. This first reduction or " blooming," is usually done in this country in a 30-inch 3-high rolling-mill, with movable rolls, so as to get several reductions in each set of grooves. The first of these mills has been running at the Troy Steel-works above a year, with great success. Another at the Cambria Iron

By Gary E. McIntosh

This paper will discuss a US Bureau of Mines project designed to assess and predict the impacts which surface coal mining will have on the regional shallow groundwater systems in the Powder River Basin. The primary objective will be met through the accomplishment of the following: (1) The design and establishment of a regional network for monitoring shallow groundwater systems in the basin; (2) monitoring the direction and rate of flow, water quality, and aquifer characteristics of the shallow groundwater systems; and (3) development of a regional groundwater simulation model, with appurtenant subroutines to determine local effects.

Jan 1, 1980

By Charles E. Wait

In the analysis of a set of interesting furnace-products belonging to the metallurgical cabinet of the School of Mines, I placed in the hands of one of my students a sample of litharge which gave the results quoted below. The collection of specimens from which this was taken, represents the products obtained in the blast-furnace treatment of argentiferous lead ores, also samples from the zinc process, and those from the cupellation of the enriched lead. The sample, when received, was marked "bismuth litharge," and was that obtained during the last stages of cupellation. It gave upon analysis the following : Per cent. Lead,.......85.36 Antimony,.......06 Bismuth ,........20 Copper,.....49 Iron,...... 69 Zinc,......18 Nickel,.....01 Silver,....2.94 Lime,.....36 Magnesia,....03 Silica,.....12 Sulphuric anhydride,. .32 Carbonic anhydride,. 1.25 Water,.....24 Oxygen,..,.7.80 99.95 At present I wish merely to call attention to the large percetage of silver present (equal to 857 ounces Troy per ton of 2000 pounds avoirdupois), and also to note two or three determinations that I have recently made, with a view to ascertain, if possible, the condition in which this silver exists. If I mistake not, it is usually assumed that silver exists in litharge in the metallic state; and it is, indeed, in the analyses of litharge, rarely expressed otherwise. This method of reporting the silver is, no doubt, due to the accepted statements that the oxides of silver are reduced to the metallic state at a temperature of 300' C. or less. The following experiments lead me to believe that silver exists in litharge, not entirely in the metallic state :

Jan 1, 1887

R. W. Balluffi (Atomic Energy Div., Sylvania Electric Products Inc., Bayside, N. Y.)—Since porosity is known to form in the copper side of Cu-Ni couples during diffusion24,25 it is of importance to consider this factor in interpreting the large variations of chemical diffusivity with copper concentration reported for this system. The presence of porosity may affect the measurement of D in two ways: 1—density changes in the couple invalidate the usual solutions of the diffusion equation, and 2—the pores may act as short-circuiting paths when transport through the vapor or along internal surfaces is appreciable or else as open circuits when these effects are small. The error produced by the first effect may be estimated by a graphical analysis. Fig. 8 shows the porosity generated in the copper side of the Kirkendall interface of a pure nickel vs pure copper couple after diffusion for 350 hr at 1040°C in hydrogen. In Fig. 9 the actual diffusion curve which would be obtained by the usual slicing technique is shown as a solid line drawn to the same scale (from the data of da Silva and Mehl"). The amounts of porosity (obtained by lineal analysis) and of nickel are graphically represented by the hatched areas. The standard solutions of the diffusion equation are valid only when all volume elements of unit length and unit cross section contain equal numbers of atoms." It is possible to correct the experimental curve to satisfy this condition by shrinking the couple in the direction of diffusion in such a way as to eliminate the porosity.* The corrected diffusion curve obtained after

Jan 1, 1954

By B. Heide, A. Bergrnann

The Meggen mine and the concentrator plant of the Sachtleben Bergbau GmbH are located in the southern part of the Ruhr district of the Federal Republic of Germany. The mine has been in operation for more than 100 years, but the concentrator described in this paper was started up in January 1963. The Meggen orebody is of sedimentary origin and occurs in a zone of limestones, graywacke and shales of Devonian age. The average thickness of the deposit is 3 meters and due to an intense folding of the area, the mineralized zone dips steeply at 80º towards the north.

Jan 6, 1973

By D. J. Cox, J. P. Conway, A. E. Gooch

A two-year test conducted by the USBM's Spokane Mining Research Center (SMRC) has proven the feasibility of the yielding rockbolt, a concept which may prove very useful to the mining industry by providing ground support under a variety of conditions. The yielding rockbolt was originally developed in South Africa3 to overcome the limitations of conventional bolting in rock subjected to high-stress or rock burst conditions. The yielding effect is obtained by fitting the bolt prior to thread rolling with a smooth-bore die of internal diameter slightly larger than the shank diameter but smaller than the rolled thread diameter.

Jan 4, 1977

By Robert R. Britton

A study conducted at The Ohio State University sought to deter- mine whether explosives break rock primarily employing shock energy or energy stored as borehole gas pressure. The amount of broken material, calculated borehole pressure, and measured stress waves are compared as decoupling ratios (borehole diameter/explosive charge diameter) increased from 1 to 3 and all other variables remained constant. Breakage and calculated borehole pressure displayed a decrease as the decoupling ratio increased while the shock energy remained constant. The strong implication is that borehole gas pressure is the primarary force in breaking rock with explosives.

Jan 1, 1984

By Howard L. Hartman

Probably no aspect of underground excavation is as important or as neglected as the environment. The Committee on Rapid Excavation, formed by the National Academy of Engineering to study the technological needs for "rapid" underground excavation in tunnels, shafts, and mines of the future, encountered a blank wall in attempting to evaluate environmental needs. In fact, so little quantitative information on the extent of present-day hazards is available that projection of future environmental-control demands must await more adequate assessment of current hazard levels. Further, there are not even accepted tolerance standards for many environmental conditions, such as heat, noise, and illumination. Only certain atmospheric contaminants have been satisfactorily catalogued. Any technical study, therefore, which purports to examine the state-of- the-art on underground environmental control must, in reality, settle for a cursory survey of a rather nebulous subject. ENVIRONMENTAL HAZARDS To contend adequately with hazards in the underground environment requires some knowledge of their nature and characteristics. In this regard, it is helpful first to identify our concern: when, where, and to whom or what may environmental conditions constitute "hazards"? Table 1 summarizes considerations that are important in this regard. For the purposes of this Conference (and book), primarily directed toward the excavation process itself, the hazards of consequence occur during excavation (item A) and primarily within the excavation (item B). However, some attention must be given to external hazards as well, since these may affect excavation. The object of concern (item C) is mainly human safety, although property security is also important. Hazards occur in a variety of forms. If one is to devise suitable control

Jan 1, 1970

By Donald Towse

Geothermal energy can substitute for and compete with other fuels, but until now it has been used only in special situations where it costs much less than alternate fuels. Geothermal heat is expected to be developed where it can: (1) compete with alternate fuels, (2) replace scarce fuels, (3) be more environmentally acceptable, or (4) is especially adapted to local needs. Economic problems in development include the often high capital costs of wells and gathering systems and the long lead-times required for electric generating plants. The large investment and long payout times for large industrial uses adversely affect the economics.

Jan 1, 1977

The John Fritz Medal for the year 1917 has been awarded to Professor Henry Marion Howe for his investigations in metallurgy, especially in the metallography of iron and steel. Record of the John Fritz Medal. The John Fritz Medal Board of Award has published a book giving a history of the Medal, the Rules of Award, biographical notices of the medallists illustrated with portraits, etc. This beautiful book, designed, engraved and printed by Bartlett Orr Press, New York, may be obtained by addressing the Secretary of John Fritz Medal Board of Award, Engineering Societies' Building, New York. Price $3 per copy.

Jan 3, 1917

THOMAS T. READ, Palmerton, Pa. (communication to the Secretary*). -It is much to he regretted that in presenting a further discussion of these deposits, first described by myself' and later discussed by C. M. Weld,2 Mr. Wang bas not made a more complete presentation of the evidence on which he bases his conclusions as to their origin. Mr. Weld said in his paper that his visit was confined to a few hours, that he saw only one of the several exposures, and that he took away no samples for further study. My own visit was brief, and for another purpose than the study of the geological features of 'the deposits, so the fact that Mr. Weld described as a hornblende-granite the rock which I described as a "dark gray syenitic rock," and which Mr. Wang identifies as a hornblende-syenite, seems of no great importance, since this rock is generally decomposed along the contact, presumably the only place in which Mr. Weld observed it. Later in the same paper (p. 31), Mr. Weld says that his opinion is that the magnetite of the deposits is primary, but Mr. Wang makes no mention of this in stating his own conclusion to the same effect. When Mr. Weld's paper appeared, I did not discuss it, because, although I considered the evidence- that he brought forward to support his belief that the magnetite is primary too slender to support the hypothesis, my own evidence to the contrary was equally tenuous. .The opportunities for observation and study open to Mr. Wang must have provided him with

Jan 6, 1917

By AIME

IRWIN W. ALCORN, present Chairman of the Petroleum Division, was born Sept. 5, 1899 at Marietta, Ohio, and moved with his family to Robinson, Ill., at the time of the early oil development there. This was in the days of the Star spudders, mud, mules, and Stanley steamers. Al graduated from Robinson High School after participation in basket ball, also attaining the captaincy of the football team of that school. He entered Missouri School of Mines and Metallurgy in 1918 and was ushered by the Army into the S.A.T.C. In 1920 he transferred to the Massachusetts Institute of Technology, later to return to receive his B.S. degree -in metallurgy at Rolla, also joining the AIME. On graduation, he worked for the Skelly Oil Co. at Cushing, Okla., shifting to the Moore Refining Co. at DeNoya, Okla., as superintendent of a small pipe-line system. After an interval of two years with the National Supply Co. in Tulsa, he joined the Independent Oil and Gas Co. of that city, and at various times was chief engineer of the Texas division, superintendent of the West Texas pipe-line system, chief engineer of pipe-line construction, and chief engineer of the refining division. Al organized the Company's production engineering department. In 1930 the Company was merged with the Phillips Petroleum Co. The depression was in and Al was out, 'as was true nine months later when the Smith Separator Co. whose chief engineer he had become, was liquidated. The next few years was spent with Oil Well Supply Co. as a subsurface pumping equipment engineer

Jan 1, 1948