Search Documents

By Roscoe Bell

An economic appraisal of the western phosphate industrial potentials made between 1945 and 1948 revealed possibilities for a considerable expansion in the production of high analysis phosphate fertilizer. The most significant facts are: (1) a rapidly increasing and a much larger potential market which might be reached from the western deposits, (2) the existence of large undeveloped deposits of phosphate rock, (3) potential energy from sulphuric acid, coal, or hydroelectric power in the general vicinity of the deposits. The challenge to the mining and metallurgical engineering profession is in the economical development of phosphate mines and in improving processes for utilization of the western ores and the recovery of byproducts to make the expanded western industry satisfactorily compete with the industry in the East and South in meeting the fertilizer needs of the Midwest and Far West.

Jan 4, 1950

By J. I. Budnick, W. B. Ittner III, D. P. Seraphim

A reliable technique has been developed for producing single crystals of tantalum in the form of small diameter wires. By suitably heat treating these and polycrystal samples, first in an oxygen atmosphere and finally in vacuum, it has been found possible to reduce residual resistivities to 10-3 microhm-cm. The purity of these samples is thus comparable to the purities obtained in zone-refined silver, copper, and aluminum. THE growth and purification of pure single crystals of the transition metals is, in general, difficult. The high melting and annealing temperatures of these metals make it necessary to employ rather special techniques in any crystallization process. In addition, the transition metals show a great affinity for and are easily contaminated by nitrogen, oxygen, and carbon. Recently, however. a number of investigators have been successful in growing,

Jan 1, 1961

By D. C. Jillson

THE data on the critical resolved shear stress for zinc single crystals published by Rosbaud and Schmid1 showed many irregularities, as seen in fig. 1. There have been subsequent investigations,2,3 but no one has repeated this work with a wide range of orientations, with specimens of a higher degree of purity and perfection, and with improved experimental techniques in order to determine whether these variations were entirely experimental or whether they might have been due, at least in part, to some feature of the mode of deformation not known or understood. Mathewson4 and others have long felt that the glide observed in a [100]* direction between two (001)* planes in the zinc lattice might be actually the net effect of many consecutive unit glides or movements in two alternating [210] directions (fig.

Jan 1, 1951

By E. C. Herkenhoff

THIS subject may be controversial. Personal preferences influence the final selection of cyclones, and side issues such as costs, floor areas, head room, and ease of replacing worn parts all enter the picture, but the following comments and data should apply to most cyclone selection problems. Broadly, the uses for cyclones in wet classification may be divided into three fields: 1) Open circuit operation, for two products, in which feed rate and sizing vary and the products vary. For example, feed may be divided into a sand product and a slime product. 2) Open circuit operation, for two products, in which feed varies, one product to have constant sizing. This calls for adjustment in either the apex or the vortex aperture. 3) Closed circuit operation, the finished product to have constant sizing. Most classification jobs fall in this category.

Jan 8, 1957

By Clifford C. Hanninen, Allan H. Caverson

Within the past nine years a means for measuring the distance between mine roof and floor was developed at the White Pine mine which yields relevant information utilized in the mining operation. The technique known as "convergence" is an efficient, low cost way for obtaining large quantities of data for predicting roof falls, caving activity and overall mine stability. Since 1964 the activity of convergence measurements has expanded to become a production tool found in all sections of the mine. The program involves four types of activity: 1) monthly measurements in areas known to be active and in sample blocks scattered throughout the mine for a long-term stability study; 2) semi- monthly measurements along vital travel roads, belt drifts and compressor sites; 3) weekly measurements in areas where men are working; 4) daily measurements in pillar-recovery and caving operations.

Jan 5, 1973

By Gunnar Almgren

Hole deviation has great consequences on mining economy, especially for long hole drilling technique. First of all the bore hole datas are concerned but also such factors as development, loss of ore and waste rock dilution are influenced. Hole deviation for sublevel open stoping is illustrated with examples from some mines. The deviations are indicated as mean values but also as standard deviation values, owing to their statistical distribution. The economic influence of the hole deviation is especially studied for steep, small lowgrade orebodies, mined with big hole blasting. Hole deviation can thus influence costs up to US$ 3-4 per ton for operating, development, losses of ore and rock waste dilution. This cost is of the same magnitude as the total operating costs for many sublevel stoping mines. The economic savings in accurate drilling are therefore substantial and are worth all attention.

Jan 1, 1981

By A. T. Yu

Over the last 80 years the conveyor belt has advanced from the troughed rubber belt to those with standard steel cable cores and those which can navigate curves or climb steep inclines. Now the latest generation of belt conveyors can claim hitherto unheard of capacities of 20,000 tph and single flight lengths well exceeding 16,000 feet. The stranded steel cable core belt is principally responsible for the spectacular improvement in load carrying ability of belt conveyors. The allowable working tension of these belts ranges from 2,500 lb per in. of belt width for 1/4 in. diam cable to 4,000 lb per in, for 3/8 in. diam cable. These ratings far exceed the 240 lb per in. per ply for rayon or nylon construction, and 30 lb per in. per ply for a lowcost cotton fabric.

Jan 1, 1970

By R. L. Loofbourow

The objectives of this report are (1) to indicate what is known of natural rock temperatures as deep as 5000 ft below the surface, (2) to indicate methods for estimating such temperatures in localities where directly measured temperatures are un- available, and (3) to outline as far as possible, areas in the 48 states within which rock temperatures are likely to be low and high. The usual object of temperature measurements in deep mines and wells is to learn the temperature of air or another circulating medium. This usually differs significantly from the undisturbed rock temperature. The subject is complicated further by the variety of the thermal properties and structures of rock masses, the migration of fluids within them, the diversity of the history of rock masses and of the processes which have been at work on them during that history.

Jan 1, 1966

By D. B. McDyre

THE object of this study was to compare variations in slag volumes with tap changes while maintaining all other factors constant. This meant: 1. Same type of heat (Spec. SAE 1030). 2. Same charging material (3500 lb foundry, 4000 lb bought scrap). 3. Same amount of sand by weight to fix slag line. 4. Same method of melting with the exception of tap changes. 5. Same method of weighing slag after each test. The equipment of the Dodge Steel Co. consists of a 132-ton Heroult furnace lined with silica brick, using three 8-in. electrodes and a 2000-kva transformer, with four tap changes. In the melting practice we use a Fischer Carbanalyzer and a Herty viscosimeter and try to standardize all heats by making necessary carbon and slag adjustment before boil to keep all heats as uniform as possible.

Jan 1, 1947

Some specific observations might be appropriate concerning the reporting of Research and Development results. Each report is usually directed towards a particular group, such as technical, operational financial, or marketing. The requirements and background of the group receiving the report must be considered, and the emphasis and coverage geared to the training of people concerned. For reports that might have large and varied distribution, it is often feasible to group, either as sections or appendixes, the special details and information of interest only to certain functions within the organization. (A check list prepared in conjunction with the various users of the report is sometimes useful to prevent omissions.) Typical points listed might be: Financial- (1) capital requirements, (2) timing of capital expenditures, (3) tax implications, including depreciation, depletion and investment credits, (4) changes in working capital.

Jan 10, 1967

By C. Feng, C. Elbaum

AN investigation of the fracture plane of titanium, containing 0.5 wt pct to 1 wt pct 0, was recently carried out by fracturing large-grain specimens in a tensile jig at room and liquid air temperature. The experiments were carried out on strip specimens 3 to 5 mm wide, 2 mm thick and about 100 mm long. The specimens consisted of several grains, each occupying the entire cross section of the strip and extending over a length varying from 5 to 20 mm. These specimens were prepared by a method described elsewhere.' The identification of the fracture plane was possible in twelve of approximately thirty crystals investigated. In some cases severe local distortion took place near the fracture and prevented identification of the fracture plane. On, at least, three occasions the fracture propagated in a helicoidal

Jan 1, 1959

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) Position in sales department is open for a mining engineer with experience in mine ventilation and possessing some knowledge of fan design; one competent to lay out ventilating systems to meet various conditions. No. 2. A large company manufacturing mining machinery has an opening in one of its Western agencies for a young mechanical engineer who has had some experience in designing along general machine shop lines, and who is familiar with cost systems. No. 3. A large university desires to secure a prominent metallurgist for a vacant professorship in metallurgy. No. 4. Opening at a mine in New Jersey for a technical graduate to begin work as chairman on the surveying squad. Salary $50 per month to start. No. 5.

Jan 11, 1913

By L. D. Mullins, H. B. Bradley

Numerous articles have appeared in the literature citing the application of the potentiometric analyzer to cycling operations. Specific information obtainable by a potentiometric analysis, as noted by various investigators, includes: 1. Pattern sweep efficiency for various injection and production rate programs. 2. Injected fluid breakthrough time at production wells. 3. Optimum production and injection rates. 4. Prediction of injection and/or production well locations. 5. History of advance of the in-jected-produced fluid interface. 6. Ultimate life of the reservoir. 7. Ultimate reservoir production. This note describes a procedure for predicting pressure distribution in a gas-condensate reservoir by using the potentiometric analyzer to obtain potential distribution data on an analog model of the reservoir and then applying Muskat's' equations. The method relates the volumetric weighted average datum pressure to the mean potential in the model.

Jan 1, 1958

By George Schore

Radiation grafting of ion exchange structures contains ion exchange groups but may consist of neutral groups. High energy grafting of monomers on to polymers has-been known since 1950 (1.2); manufacture on an industrial level was-begun in 1970.(3) Proper choice of substrate and monomer will produce various ion exchange membranes with differing physico and chemical properties. Grafting a selected monomer to the proper polymer will provide selective ion exchange with assured chemical protection of the substrate. Ion exchange systems utilizing radiation grafted structures to polymers have been fabricated to "capture" gold from drag-out and rinse water and silver from cyanide rinse water. Other ion exchange systems can feasibly be produced to remove other precious metals. Rotating Cathode Technology is used to recover the metals from their concentrated eluating solutions as pure metal foil.

Jan 1, 1984

By W. L. Falke, A. A. Cochran

Vast deposits of low-grade manganese ore exist in the United States, yet domestic production is insignificant compared to the more than 2 million tons of ore imported yearly into this country.1 A basic problem in connection with manganese is to find economical ways to utilize domestic resources.2 As a part of its program to conserve domestic mineral resources and to reduce dependence on foreign sources, the U.S. Bureau of Mines has conducted extensive research to broaden manganese technology and to find economical processes for recovering manganese from these low-grade resources. Although a great many processes have been proposed for treating domestic manganese resources, a failing of many of them is that too many steps are involved for economical operation.2 Some of the major processes that have been proposed were reviewed by Norman and Kirby.3,4

Jan 3, 1967

By S. R. B. Cooke, R. O. Huch, C. S. Chang

IN the flotation of iron ores laurylamine derivatives have been used for considerable time.12 To effect satisfactory separation of the gangue, predominantly silica, from the iron oxide minerals, the addition of specific depressants for the iron oxides has been found necessary. Starches and starch products have been used for this purpose. 3 There is, however, very little published information on the effects of these materials and other variables on this process. In some cases it has been found that prior acid scrubbing and desliming are essential, 4 and depending upon the efficiency of the subsequent washing step, there will be accompanying changes in pH. It was the object of this investigation to test and observe the effects of the above factor as well as to examine and compare the action of various starches and starch products.

Jan 12, 1953

By W. C. Ellis

For the purpose of developing combinations of higher strength and conductivity than are obtainable by heat treatment alone in the age-hardening copper alloys, an investigation has been made of the effects of combinations of heat treatment and strain hardening on the properties in question. The investigation was limited to a study of the alloys containing nickel and silicon; nickel, silicon and cadmium; and cobalt and silicon. The experiments made in the course of the study are described in this paper in three groups: 1. The effect of hard drawing subsequent to heat treatment on the mechanical and electrical properties of the alloys. 2. The effect of low-temperature aging on the properties of heat-treated and hard-drawn alloys. 3. The effect of strain on the rate of aging of quenched nickel-silicon-copper alloys.

Jan 1, 1931

By Robert P. Uhley, LeRoy Scharon

TEST gravity surveys were made in the Washington County barite district of Missouri on property owned by the Baroid Sales Division of the National Lead Co. This property is located just northeast of Richwoods in the northeastern corner of Washington County, Fig. 1. The area to which the surveys were confined comprised approximately 5000 acres, of which some 525 acres were surveyed gravitationally. Gravity observations were made at 2600 points within the area, observations being confined to relatively clear and gently sloping ground. Part of the area was heavily wooded, and the terrain too rugged for either the occurrence of a commercial barite deposit or a feasible gravity survey. The relief along the central drainage, Ditch Creek, was about 140 ft, the maxi- mum difference in elevation being 400 ft in a distance of 3 ½ miles.

Jan 1, 1954

By L. Webster Wickes

The bad effects of arsenic in commercial copper are well-known to metallurgists. The refining of copper by electrolysis eliminates practically all of the arsenic, provided certain requirements are fulfilled. The first, and most important, of these requirements is, that the voltage of the depositing current shall not be too high. It has been known for some time that the percentage of arsenic in the deposited copper increases with the voltage. To investigate the relation between the electro-motive force (e.m.f.) and the freedom of the precipitated copper from arsenic, the experiments were made, of which a brief summary is here given: I made three copper-arsenic alloys, containing respectively 3.56, 2.24 and 0.96 per cent. of arsenic. From these alloys I cast several anodes. For cathodes I used sheets of thin copper,

Jan 1, 1905

By J. J. Marcus

Mineral industry decision-makers are frequently required to select between competing equipment. Various criteria and methods are currently being used, and this writer would like to suggest a method recently tested on two large power shovels in an open pit mine. An initial examination of both shovel A and shovel B indicated that the latter should give the best overall results. since: 1) It swings 13% faster; 2) it carries a dipper with 23%: greater capacity; 3) purchase price is 8.6% lower; 4) shovel weight is 12.5% greater; 5) it has considerably greater bail pull under most operating conditions; 6) the electric controls are of a more modern design. However, shovel B has half the service life. With these points in mind, shovel A was selected by The Buckingham Method, an operations research technique.

Jan 9, 1965