Search Documents

In seeking to improve the economic performance of mines, the management or human aspects are usually seen to be quite seperate from, and more significant than, the technical aspects. There are obvious aspects of industrial relations, man-management, skills training and supervision that are currently the focus of efforts to improve the productivity and quality of the mining process. However technology also has a lot to offer. Analysis of the costs involved suggests that innovations leading to improvement in the productivity of the excavation and transport of overburden and the recovery of coal (both in the mine and preperation plant) can lead to improvements in the economic performance of a mine that may outstrip the obvious non-technical or management opportunities for improvement. While there are some innovations currently being investigated within the industry that relate to the design of mining equipment, the type of machinery being used in open cut mines has not changed dramatically over the last twenty five years. It is also likely that mining equipment will remain essentially of the same form in the forseeable future. If significant improvements to mining performance are to be achieved other than by futher increases in the scale of machinery, then we need to seek ways to operate these same types of machines in a more productive and controlled manner. This paper discusses the identification of mining processes the improvement of which is likely to have a significant effect on mining costs and performance. Some areas of current research are discussed and potentially fruitful areas for future development are identified.

Jan 1, 1991

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By Drinkwater DJ, Watsford RMS, Johnson NW, Munro PD

This paper describes the use of modelling and simulation techniques in the analysis and optimisation of grinding circuits at the Lead/Zinc Concentrator of Mount Isa Mines Limited.The objectives of the studies were to: -1. improve primary grinding circuit performance by reducing the production of -0.006 mm galena fines.2. maximise the fineness of grind in the second existing grinding power and pumping capacitie The study has shown that quantitative models can operations. The models described plant operation,,and simulated the effect of process changes on plant performanc The use of automated scanning electron microscope technology tcliberation characteristics of the major minerals in the Mount isa Lead/Li ore is also described.

Jan 1, 1985

By B Manda, K L. Sandvik, K Musiwa

Mining and processing of pyrite ore at Iron Duke Mine, north east of Zimbabwe, generates large quantities of acidic mine water as a result of the oxidation of iron sulfides on exposure to air and water used in the drilling and blasting operations. The acid mine drainage (AMD) contains elevated levels of dissolved Fe, Al, Mn and sulfate and has characteristic pH values ranging from about 0.50 to 3.00. Handling and disposal of such a drainage places significant impacts on the economics of the mining operation due to the corrosive nature of the drainage on infrastructure, the limitations placed on water reuse and discharge to the environment under a new law governing effluent discharge. Treated sludge at Iron Duke is chemically unstable, changing pH from ~7 to ~3 within four days after deposition in the evaporation ponds. The effluent does not meet the permitted level of neutral pH, 500 mg/l sulfate and less than 2000 mg/l total dissolved solids. Excessive acid seepage from the evaporation ponds has resulted in contamination of the ground water below the ponds area, which shows high mean annual levels of iron (368.67 mg/l), sulfate (1702.89 mg/l) and low pH (2.86) in addition to other pollutants. This poor quality seepage infiltrates into the nearby Yellow Jacket River, contaminating the public water source. Furthermore, a deterioration of the land area and vegetation adjacent to the tailings dump is also observed. Understanding the controls on the neutralisation of acidic drainage and long-term sludge stability after placement in evaporation ponds is essential to minimise costs of closure requirements and for the protection of environment and human health. This study examined the effects of the master variables pH, redox potential, acidity and alkalinity on acid neutralisation. The results indicate that ferrous hydroxides are not as stable as ferric hydroxides and that proper oxidation of iron also leads to better sludge stability, higher treatment efficiency and a manageable sludge viscosity. Metal hydrolysis and secondary mineral formation at the evaporation ponds under a wide range of pH and redox conditions is responsible for equilibrium shifts in metal reactions, resulting in high potential for metal leaching and mobility. Mechanisms of metal attenuation are also discussed.

Jan 1, 2006

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

By T C. Westerfield, G, M J. Mankosa

An innovative separator known as the HydroFloat cell has been developed specifically for the upgrading of coarse particles that are difficult to recover using conventional flotation cells. The novel characteristic of this separator is the formation of a hindered teeter-bed of fluidised solids into which small air bubbles are injected. The air bubbles selectively attach to hydrophobic particles and form particle/bubble agglomerates that segregate atop the teeter-bed due to their lower apparent specific gravity. The low-density agglomerates are eventually carried into the product overflow launder by the rising current of teeter water. Hydrophilic particles remain in the teeter-bed and are discharged to underflow as a high solids content tailing. Benefits of this hybrid flotation-density separator include enhanced bubble-particle contacting, increased particle residence time, and very low air demand. Test data indicate that significant improvements in the recovery of coarse particles can be achieved using this innovative technology. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent pilot-scale tests conducted for the phosphate industry.

Jan 1, 2005

By B C Tanda, E A. Oraby, J J. Eksteen

"Base metal and precious metal deposits are well known for their significant geometallurgical variation throughout the volume of the proven resource. At the metallurgical level, the plant normally processes an upper oxidised layer, a transition zone and a sulfide zone, often leading to different processing techniques for the different zones. A novel processing approach is presented whereby alkaline leaching with glycine is used to leach base and precious metals, using a copper-gold ore deposit as a case study. Glycine is a cheap, non-toxic, non-volatile, highly water-soluble crystalline solid produced industrially in bulk quantities. As a chelating ligand it forms a number of stable glycinate complexes with Ni, Co, Cu, platinum group metals (PGMs), Au, Ag, Zn, Pb, Hg and Cd, with broad stability regions over an extended temperature-pH-Eh range, allowing dissolution of these metals in the neutral and alkaline regions (pH 7–13). It has been shown that this lixiviant system can leach the metals from their oxide, oxy-halide, basic sulfate, carbonate, native and various sulfide forms, including refractory sulfides such as chalcopyrite. Extraction of the metals from their soluble glycinates is easily achieved using a range of solvent extraction and precipitation processes, and the glycine remains stable in aqueous solution for recycle and reuse. Minerals bearing metals in Groups 1 to 8 of the periodic table are normally unaltered. This technology therefore provides a highly selective leaching environment for the extraction of numerous scarce metals of economic interest, with minimal interaction with gangue minerals, whilst using environmentally benign reagents. Problematic leach residues such as jarosites, elemental sulfur and silica gels are averted through this processing approach. This technology allows hydrometallurgical processing that is much less domain-sensitive in the geometallurgical sense, and utilises essentially the same key reagents for the whole deposit.CITATION:Eksteen, J J, Oraby, E A and Tanda, B C, 2016. Developing Robust Hydrometallurgical Processes to Recover Metals from Deposits with Large Geometallurgical Variation, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 15–20 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Mingmin Dou

The behaviour and deportment of indium during the precipitation of sodium jarosite from Fe2(S04)3 - Na2SO4 solutions were investigated. Indium is readily precipitated with sodium jarosite, and the extent of In precipitation increases as the In concentration of the solution increases. It was shown that In 3+ substitutes for Fe 3+ in the jarosite structure to form a nearly ideal solid solution series. On a molar basis, the precipitation of Fe is slightly favoured over that of In, and the difference is reduced as the pH increases. Sodium jarosite precipitation becomes kinetically rapid at temperatures >70¦C, but increasing temperatures in the range 70 to 150¦C affect neither the relative precipitation of In and Fe nor the composition of the jarosite product. Low Na2SO4 concentrations result in reduced product yields and jarosite precipitates in which H3O' > Na+. The hydronium-rich precipitates have reduced In contents. Increasing the ZnSO4 concentration of the solution slightly increases the quantity of jarosite formed and results in the incorporation of -0.3 per cent Zn in the jarosite structure. Otherwise, the presence of ZnSO4 has no significant effect on the composition of the jarosite. Seeding accelerates the rate of jarosite precipitation but has a negligible influence on the deportment of In. The jarosite precipitation reaction at 98¦C is relatively rapid and near-steady state conditions are achieved in - 6 h even in the absence of seed. The initially precipitated jarosite is slightly enriched in In with respect to Fe. The ferric ion concentration of the solution has a significant influence on both the amount of jarosite formed and its composition. In particular, the jarosites precipitated from dilute Fe3+ media have significantly enhanced In contents. Hence, it may be possible to recover - 25 per cent of the dissolved In, at the 1000 mg/L level, in a jarosite precipitate assaying - ten per cent In by the controlled oxidation-precipitation of sodium jarosite from a ferrous sulphate processing solution.

Jan 1, 1993

Since the 1950's drilling has been rapidly mechanised. First from hand held drills with air legs to pneumatic jumbos, then to more effective hydraulic jumbos. Development of underground drilling equipment naturally could not have stopped here. Hydraulic drilling saw an improvement in drilling capacity and efficiency after the introduction of second generation drifters in the early 1980's. Also in the early 1980's a few equipment suppliers started to study how to improve the efficiency in operating the rigs. The first computerised rigs for tunnelling were delivered to work sites in mid 1980's. At the same time a few computerised longhole drills started drilling in mines.

Jan 1, 1988

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

Rope guides, consisting of ropes spanning between anchor points at the top and bottom of shafts, have frequently been considered as a viable alternative to fixed guides, comprising buntons and guides. However, their design has generally been based on empirically derived rules, arising from European hoisting practice of 50 to 100 years ago. This paper describes a recent technology development project aimed at defining and quantifying the important forces acting on rope guided conveyances, calculating the resulting displacement of the conveyances and assessing whether the displacements are acceptable or not. The paper describes the derivation of aerodynamic force coefficients based on CFD analyses and other significant forces acting on the conveyance and rope system. The conveyance displacements may be calculated using computer simulation of the mechanical system, or approximately using simplified equations given in the paper. Measurements taken to confirm the suitability of the proposed formulation are described. The combination of displacements and assessment of the rope guide system design are proposed, based on the ratio of design clearances and the predicted displacements.

Jan 1, 2005

By A Van Kersen, J Hodson

Waihi Gold Mining Co Ltd [WGM], operated by Normandy Mining, has been internationally recognised for its achievements in environmental management at the Martha Mine at Waihi. In a proactive approach to dealing with community concerns regarding blast vibrations on the North Wall cutback, trials were performed using the Cardox System [Cardox], to determine feasibility of achieving economic fragmentation of andesite overburden whilst bettering management levels of 5 mm/s peak particle velocity. Cardox is a non-explosive pressure breaking system which uses high pressure CO2, Results against conventional Ammonium Nitrate/Fuel Oil [ANFO] using a variety of delays showed that conventional blasting techniques could produce marginal fragmentation within the management levels with occasional excursions, whereas Cardox produced the required fragmentation while not registering on the vibration monitoring equipment. Fragmentation to enable normal excavation by a Hitachi EXII00 hydraulic excavator was achieved with a yield of 16m3 per round. The trails indicated that fragmentation with Cardox at the yields required of over 18m3 per round was possible with further product development. The trial demonstrated that non-explosive pressure breaking is feasible and its application warranted where environmental concerns affect the cost-benefit economics of production blasting in sensitive areas.

Jan 1, 2001

By C R. Fountain, R J. Sinclair

The zinc industry is dominated by the electrolytic zinc (EZ) process. The EZ process has a low tolerance for impurities, resulting in tight concentrate specifications. Many mining companies sacrifice zinc recovery in order to meet smelter specifications. Some have ore-bodies that cannot be economically developed because too much metal has to be sacrificed, or it is just not possible to meet the specification. The BUKA Zinc Process (BZP) has been developed as a method of producing high-quality zinc from a wide range of concentrates. It can have lower capital and operating costs than the conventional zinc and lead production routes. Advantages accrue from increases in metal recovery during concentrating, smelting and refining; the elimination of most of the capital and operating costs associated with lead smelting; reduced transport costs; lower zinc refining costs; reduced refinery residue disposal costs; and reduced future environmental liabilities. This paper describes results of testwork that has been undertaken to demonstrate the viability of the BZP on both test rig and laboratory-bench scale.

Jan 1, 1998

Breakwater Resources Ltd is a Canadian base metals producer with Cu-Pb-Zn operations in Canada, Honduras, and Chile. Two of its operations contain economical gold levels which are recovered in both gravity and flotation concentrates. The gold payable terms in zinc concentrate are poor when compared to gold concentrates or copper concentrates and various flow sheets have been evaluated by Breakwater staff to maximise gold reporting in higher value products. The Myra Falls mine in British Columbia recovers coarse gold in the grinding circuit, part of which is upgraded and sold as a gravity-gold concentrate with the balance being directed to the copper concentrate. A sampling survey showed that there was potential gravity-recoverable gold in the copper regrind circuit. Installing a gravity concentrator in the copper regrind circuit increased the gold grade and recovery in the higher revenue copper concentrate and reduced the quantity reporting to the less well paid zinc concentrate. The El Toqui Mine in southern Chile has distinct high-and low-gold orebodies which are campaigned separately through the flotation plant. The high gold zone yields both a gravity concentrate and an unusual gold flotation concentrate. The gravity concentrate undergoes intensive cyanidation and electrowinning on-site to produce dore, while the fl otation concentrate is sold to gold producers. The zinc concentrate contains signifi cant gold values. The paper describes efforts over the past few years to improve gold returns at Breakwater's operations and highlights the different approaches dictated by the mineralogy of the gold occurrences at these two operations.

Aug 1, 2010

By Sturchio NC, Williams SN, Fischer TP

Chemical and isotopic analyses of fumarole gases from Galeras Volcano, Colombia provide significant insights into the origin of volatile components in the magma.. Water comprises a mixture of magmatic (rock-equilibrated at high temperature) and meteoric, with the relative proportions varying through time. Carbon isotopes are most consistent with a mantle source, although other contributions to the system cannot be ruled out. Nitrogen most likely originated from organic matter in subducted oceanic sediments. All of these "primary" components have been modified somewhat by interaction or exchange with other reservoirs during ascent to the surface. In addition to information on the origin of the gases, these data show significant temporal variations precursory to eruptive events. Chemical ratios change and water becomes more meteoric in character prior to eruptions.

Jan 1, 1995

By R Belissont, C Veloso, L Senez, F Vasconcelos, E Kleiderer, J Mesquita, Y Basselin

Mont-Wright mining complex is an important asset of ArcelorMittal located in the province of Quebec, Canada. It is composed by Mont-Wright and Fire Lake mines, operating 365 days per annum, and producing 25 Mtpa of iron ore concentrate with 66 per cent Fe. Mont-Wright concentration plant is composed by seven lines with a flow sheet encompassing AG/SAG milling, primary and secondary classification stages, spiral concentrators (rougher, cleaner and recleaner stages) and dewatering unit operations. In this context, an equation called ‘Wrec’ was developed in 1971 with the objective of estimating the mass recovery of the different blocks in the beneficiation plant and support the mining planning works of Mont-Wright complex. This equation was based on the correlation between the results of heavy liquid tests performed with drill core samples and spiral concentrators pilot scale tests, returning an estimative of concentrator yield. However, since its first development, no updates have been done in the equation, which lead to some deviations from expected recoveries in the last years. This is probably due to the changes in the process and in the ore fed into the concentrator during the period. In this way, the study presented here corresponds to the execution of heavy liquid/spirals pilot scale tests with 26 composite samples collected at Mont-Wright deposit aiming at revising and updating ‘Wrec’ equation. Based on test work results, an updated formula was established to estimate the plant recovery and a comparison performed using industrial data showed that the old formula overestimated the real yield by 5.40 per cent, on average. At the end of the study the new equation was incorporated into the mining planning process.

Sep 18, 2023

By H Zhang, A Lawrence

To accommodate the fast growing need for services in Singapore’s Marina Bay downtown area, Marina South, the construction of a common services tunnel (CST) was required. The CST includes various services such as telecom cables, power lines and water pipes. A deep excavation and temporary earth retaining system (TERS) was required to facilitate the construction of the tunnels. Marina Bay is reclaimed land over thick soft marine clay which is likely to be still consolidating. The deep soft marine clay poses a big challenge for deep excavations in downtown areas where highways and sensitive structures are close by. This paper presents a case study of part of the CST Phase 1B and 2 at Marina South, in particular a 26 m deep excavation supported by a 46 m diameter temporary caisson. The construction started in late 2006 and the basic structure was completed in early 2011. The caisson was formed by 1.0 m thick overlapping diaphragm wall panels with a capping beam and three ring beams at different depths. Two-dimensional finite element analyses were conducted to predict the ground settlement, lateral displacement, bending moment and hoop stresses in the diaphragm wall and ring beams during different excavation stages. A comprehensive instrumentation and monitoring scheme was established to verify the design predictions, control excavation safety and trigger the contingency plan to protect public safety. The impact of construction activity, unbalanced temporary stockpiles and adjacent deep excavation for a mole removal will be discussed.CITATION:Zhang, H and Lawrence, A, 2014. A case history of a deep excavation in a big circular shaft in Singapore marine clay, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 581–588 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

When I was first asked to give a paper on work-life balance in the mining industry I was both excited and aware of the incongruity of my position. I have never worked in mining operations nor have I had any experience that approximates the on-site lifestyle. IÆm not really an adventurer or a traveller, I prefer writing and research to hands-on activities and IÆve never worked further than twenty minutes away from home. The perspective I offer is thus largely an objective one. I say largely since I grew up in a family where my parents work arrangements involved long-distance commuting; my dad continues to work FIFO at a coalmine in Blackwater until this day. Perhaps my tortoise-like existence is a rebellion against his flighty movements. The analysis I will be presenting today draws together a variety of sources, from member anecdotes and research on FIFO and work-life balance to the popular philosophy writings of a bald Englishman with a French name. I am speaking of the famous writer, Alain de Botton, whose television show æThe Consolations of PhilosophyÆ you may have seen on the ABC. Work-life balance is a term that gets a lot of mileage in corporate brochures and at breakfast seminars. But like many terms that get bandied around in the human resources circuit, from æteam synergyÆ to æperformance optimisationÆ, I am frequently perplexed as to what it actually means. Corporate websites are at pains to emphasise the high priority that they place on the needs of the whole person. Yet in terms of substantive content, a commitment to work-life balance often seems to translate into little more than the option to take a few morning yoga classes in exchange for working a seventy-hour week. As extended work hours have taken their toll, leading to high attrition of professionals across all industries, employers are increasingly expending resources to discover just what lies behind this buzz word. The challenge for companies is to find meaningful strategies to help employees better integrate different aspects of their lives in a new era of work, as employees are sending the message that they are not willing to play work, social life and leisure off against each other in a zero sum game.

Jan 1, 2005

By B Ganesia, H Sahupala

PT Freeport Indonesia is a copper-gold mine operation located in West Papua, Indonesia about 3500 km east of Jakarta. Current ore production is about 270 000 tpd, of which 30 000 tpd comes from underground. In the future, the production from underground will be gradually increased to reach a maximum of 115 000 tpd, as the Grasberg open pit production decreases. The current and future challenge for PT Freeport Indonesia is to fill the quota of underground miners, as Indonesia does not have a long culture of underground work. At present, there are only three active underground mines in Indonesia. The lack of underground skilled labour incited the company to develop its own skilled workforce. In the mean time, to overcome the shortage of personnel, the underground management had to find a way to improve the productivity. Since 21 May 1998, PT Freeport Indonesia Underground Mine has operated with the new roster of two rotating shifts a day, 11 hours per shift. The previous schedule consisted of three nine-hour shifts per day, six days a week, for a total of 26 working days in a month. This change was intended to increase the productivity of the miners. With the previous roster, studies determined that the effective working time was only seven hours per shift. The new roster produces an improvement of effective working hours to about nine hours per shift. As a result, total production has increased by 33 per cent and the utilisation of production equipment has increased by 16.5 per cent. This paper describes the background of the decision to change the work schedule, the study carried out to evaluate the benefits and drawbacks of the new shift roster, the challenges, and then compares the results for various parameters between the old schedule and the new one.

Jan 1, 2002

By A Batnasan

The main techniques for removing phosphorus as an impurity element in iron ores are physical separation (eg magnetic separation, flotation) and chemical separation (acid leaching, alkaline leaching and bioleaching) processes. When phosphorus occurs in iron ores as phosphate minerals (eg apatite), physical separation techniques are available to remove the gangue minerals from iron ores. On the other hand, chemical separation techniques are suitable for reducing phosphorus levels when phosphorus is associated with iron oxides and hydroxide minerals (eg hematite and goethite) in iron ores. In this study, the dephosphorisation behaviour of high‐phosphorus iron ore was investigated using a combined alkaline roasting and water washing route. Roasting experiments were conducted in a laboratory electric muffle furnace using various concentrations of sodium hydroxide (0–50 g/kg-ore) at different temperatures (100–800°C), varying prolonged roasting times (0–2 h), and different particle size fractions (-45 – -250 μm) of iron ore. Subsequent water washing experiments were employed at various pulp densities (30–1000 g/L) and different times (30 s – 60 min) at ambient temperature. Hematite and goethite were the main minerals in the high-phosphorus iron ore identified using X-ray diffraction (XRD) analysis. The iron ore assaying 63.40 mass % Fe (total), 0.240 mass % P, 4.53 mass % SiO2, and 4.87 mass % Al2O3 were determined using X-ray fluorescence (XRF) analysis. The results showed that the dephosphorisation rate of the iron ore was reached 40 per cent under roasting with 50 g/kg-ore NaOH at 300°C for 2 hours followed by water washing for 30 s with a pulp density of 300 g/L, reducing phosphorus level from 0.240 mass % to 0.142 mass %. At the same time, the iron grade was reduced from 63.4 per cent to 59.5 per cent, caused by an iron loss. Results suggest that the phase transformation of goethite induces the dephosphorisation of high-phosphorus iron ore under alkaline roasting conditions

Aug 22, 2022