Search Documents

By Walraven F, Knott G. G

Using a typical small logging instrument (Neltronic KPD), a natural gamma reference section for part of the Brockman Iron Formation and part of the Mt. McRae Shale has been established in the Newman area. This is compared with the stratigraphic type section of Trendall and Blockley (1968). Folding and faulting are recognised using natural gamma logs. Because of the confidence with which stratigraphic horizons can be identified, less expenditure on diamond and percussion drilling is required to confirm stratigraphic position. Using natural gamma logs as stratigraphic control the apparent thinning of the Banded Iron Formation during iron enrichment is Demonstrated.

Jan 1, 1973

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

By Gadd D. E

Since October 1972, New Zealand Steel Mining Ltd has loaded around 10 million tonnes of ironsand concentrate from single-point mooring buoys located off-shore at Taharoa on the west coast of the North Island of New Zealand. Before the first off-shore loading system was installed a considerable research effort was applied to proving the slurry loading technique. Subsequently the system has been expanded and a new buoy, pipelines and pumping system were installed in early 1978. Since then 110,000 DWT class ore carriers have been loaded at rates of around 2600 tonnes per hour through twin submarine pipelines. This paper reviews the operation of the shiploading system and attempts to answer the question: "If the Taharoa operation were to be planned in 1980, would the same research spending be necessary or have published research results since, made such practical tests unnecessary?".

Jan 1, 1980

The control system of a mine winder or other variable speed drive has many component parts that must work together to provide the required functional performance of the machine, together with comprehensive safety features, reliability, maintainability, user-friendliness and efficiency. Modern winders use digital control technology extensively and hence software design is a major part of the overall system. It is not practical to simulate an entire mine winder in a single computer model because of the sheer mathematical complexity of the behaviour of many of the components. However, most component parts can be simulated quite easily, and related parts of the control system software can be simulated. Such simulations allow control software algorithms to be developed and tested in isolation from the real plant. Tests can be performed on the model without fear of injury to personnel or damage to the valuable plant. For example, speed regulator control algorithms and stability settings can be adjusted to and beyond the limits of stable operation, and near optimum settings can be found. This is particularly important, for example, when designing closed loop controls for emergency brake systems. Obviously, care must be taken to ensure that the computer model of the plant is realistic and takes into account as many non-linear features of the real plant as possible. Pure mathematical analysis of some systems is very difficult to perform when non-linear plant behaviour is involved. This paper shares a number of practical simulation experiences performed using commercially available software such as Matlab and Simulink to simulate various parts of the control system of a mine winder or other variable speed drive. Demonstrations of the operation of several different computer models are shown during the presentation of the paper.

Jan 1, 2005

By Graham JW, Cullen GV

edicted increase in, Aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Brown coal char, with a lower ash content and with an elemental purity similar to petroleum coke, has been produced by leaching in hydrochloric acid, washing with water and charring at 115000. The cost of processing is estimated to be competitive with petroleum coke. Without further processing the bulk density and real density were undesirably low, but. by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value and the Particle density was improved to 92 per cent of the density of petroleum coke by water-displacement or 75 per cent by mercury displacement. Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char and from petroleum coke alone, all bonded with coal tar pitch. The electrodes were tested for the usual physical properties and were, evaluated for performance in a laboratory size alumina reduction cell. Electrodes based on brown coal char alone were found to be inferior in physical properties, and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity and carbon consumption on a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 percent better electrical current efficiency than the electrodes based on petroleum coke alone. It is suggested that larger scale tests are warranted.

Jan 1, 1970

By Neto J. A N

Usually there are organisational interfaces between each stage - companies or departments. Each organisation will have different ideas about "optimum" operation. These ideas will be driven by how the performance of each is measured ' and rewarded. Therefore it is important to set up data acquisition processes with respect to maximisation of overall profitability and resource utilisation. In the simplest case - if the miners are paid on tonnes and the concentrator has severe grade penalties on concentrates, then there is the possibility of a conflict of interest over metal Balance.

Jan 1, 1991

Integrated chemical thermodynamic software and computerised databank systems have evolved over the last 15 years. The extent to which these systems have automated thermodynamic calculations relevant to extractive metallurgy is examined. The scope for further automation and the role of the expert consultant is discussed.

Jan 1, 1991

The chief use of manganese ore is in the production of ferromanganese alloys for steelmaking. Manganese ores generally occur in tropical areas, which influences the type of treatment required. Present methods of treatment are relatively unsophist- icated but demands by customers for tighter specifications will necessitate the installation of gravity concentrator at many mines At present only limited tonnages of minus j in. product can be sold hence future development will centre around methods of producing an agglomerate satisfactory to the smelter.

Jan 1, 1969

As world demand for various minerals increases the mining industry in its endeavour to satisfy this demand will, eventually,look to the extraction of orebodies which previously may have been uneconomical to mine. These orebodies may be of two types. Firstly, new low grade orebodies and secondly, remnant sections of previously mined orebodies. Some of the factors relative to remnant mining operations are discussed and the potent- ial of remnant mining in providing an important contribution to future world metal production is considered.

Jan 1, 1975

The implementation, during recent years, of the concept of distributing chilled water to improve cooling at the working faces represents a very important innovation for the mining world. In a logical extension to that concept it has been recognized that distribution of the cooling water at high pressure would provide a potential source of energy for driving water powered hydraulic machinery such as rockdrills, water jets for moving rock, and support props, in the workings. With this in mind, the Research Organization of the Chamber of Mines of South Africa is pursuing the development of such a dual system that will provide cooling in a deep mine and, at the same time, drive hydraulic machinery. A comprehensive design of such a system has been completed and has shown the concept to be entirely feasible technically using technologies currently available. A pilot system is working in a mine shaft 2000 m deep giving a pressure of 20 MPa at the bottom of the shaft and distributing the cold water into the workings at a pressure of 17 MPa. The system shows considerable potential for improving existing mining methods and will open the way for the development of new mining methods for deep mining operations.

Jan 1, 1986

By M Olsson, I Bergqvist

A Swedish table of blast damage depths has, in one form or other, been in use since the late-1970s. Its history and the underlying theory are described. New experimental and theoretical findings that point out a number of shortcomings in the table and the underlying theory are presented and discussed. A revised version of the blast damage table was recently introduced in conjunction with new but incomplete recommendations for cautious perimeter blasting. The new table leaves the difficult task of taking into account factors like decoupling, water in the borehole, the rock properties, type of initiation, charge length and the actual bit diameter to the user. This paper discusses different ways of doing this, based on the experimental findings and a recent formula for the prediction of the lengths of radial cracks behind the half-casts. The material presented in this paper is meant to supplement and extend the new Swedish recommendations for cautious perimeter blasting of tunnels, shafts, pits and road cuts.

Jan 1, 2001

An intensely sheared and mineralisedIzone occurs in the Quartz Dolerite Greenstone (or Younger Greenstone) mass on, the western limb of the Kalgoorlie Syncline. This zone comprises the western part of the Golden Mile and has produced the greater part of the 33,000,000 ounces of gold produced to date from the main mining belts. A study of.th e general geological and structural features gives rise to the expectation that the lode shear system,will continue southward on a pitch similar to that of the maln syncline whose axial plane may be referred to as the "Boulder Dyke". Although payable ore has recently been found further south than previously, the expectation of large quantities extending southward from the present mining areas is Problematical.'

Jan 1, 1964

In the past two decades the global metalliferous mineral industry has trended away from pyrometallurgical (pyromet) and towards hydrometallurgical (hydromet) technologies including biometallurgical (biomet) processes. Pyromet, biomet and hydromet technologies have all developed considerably over this period. New projects have been biased or directed by legislation towards supposedly cleaner and greener hydromet and biomet technologies. The environmental cost and energy cost of pyromet production processes for copper and cobalt are compared with comparable hydromet processes using Life Cycle Assessment (LCA). The æreal costÆ of the global warming obsession and negative public perception of pyrometallurgy include greater carbon dioxide emissions and energy consumption per unit, associated with current hydromet technologies. Specific examples for copper and cobalt produced via the different routes are provided. The poor science involved with the global warming hypothesis is discussed. The use of LCA with sensitivity analysis as a decision making tool for mineral processing projects and technology developers is discussed.

Jan 1, 2004

By W F. Bawden, J T. Paynter

This investigation involves laboratory testing and stability analysis of paste fill at the Golden Giant Mine. Site-cast samples are tested in unconfined, confined, and consolidated-undrained triaxial compression. Pore pressures during shear and consolidation characteristics are measured to determine both drained and undrained shear strength parameters and assess the potential for undrained loading. Liquefaction potential is also considered. A limit equilibrium solution is used to obtain factors of safety against failure of the fill during mining of adjacent stopes.

Jan 1, 1998

By Lai KF

The Hellyer orebody is a fine grained, massive sulphide Pb-Zn-Ag- Cu-Au deposit located in western Tasmania. Initial testwork showed that the orebody would be difficult but not impossible to treat by conven- tional flotation. A staged programme-of work was commenced to demon- strate that marketable concentrates could be produced with satisfactory recoveries. Following laboratory testing of drill core to define two flowsheets, bulk samples of Hellyer totalling 20,000 tonnes were trialled at 6 tph in the Cleveland concentrator over six months. The high through- put and extended duration of the trials ensured maximum confidence in the results and that scale-up to subsequent plants would be with a mini- mum of risk. The milling trials were successful and the Cleveland concentrator was expanded in early 1987 to treat 250,000 tpa of Hellyer ore to produce 85,000 tpa of bulk concentrates. Late in 1987 construction commenced on a 1 mtpa concentrator at Hellyer to produce separate copper/silver, lead, zinc and bulk concentrates.

Jan 1, 1988

Magneto flotation is a recently developed method aimed at simultaneous utilisation of the magnetic and flotation properties of minerals in separation processes. In this method, magnetic minerals are prevented from reporting to the froth product while non-magnetic minerals are being floated. With suitable ores, this makes it possible to reduce or entirely eliminate the cleaning and scavenging operations that are otherwise necessary in conventional flotation and magnetic separation systems. This paper describes the testing of magneto flotation on a Canadian magnetite ore. The ore sample used in the experimental work contained a total of 32.89 per cent Fe of which 87.60 per cent was magnetic in the form of magnetite. Magnetoflotation yielded, in a single step, a final concentrate assaying 69.10 per cent Fe and with an overall recovery of 84.84 per cent representing a magnetic iron recovery of 96.39 per cent. Comprehensive comparisons were made with conventional magnetic separation and flotation, and it was found that with these methods at least four processing steps were required to achieve results similar to those obtained with single-stage Magnetoflotation.

Jan 1, 1993

By Bradley AJ

Hamersley Iron Pty. Limited mines and pro cesses iron ore from two orebodies at Tom Price and Paraburdoo, situated in the North West of Western Australia. Conventional open pit mining methods are used at both sites in that material is drilled and blasted in benches, loaded by shovels and hauled to the Primary Crushers or dumped on waste or low grade material stockpiles. The present drilling fleet, consisting of eight high capacity Bucyrus Erie Rotary drills has evolved from an initial fleet of a large number of small percussion rigs. There are significant physical differences between the ore types encountered at both mines which nec- essitate the drilling of smaller diameter blast holes at Paraburdoo than those at Tom Price. The drilling practice at each site is dis- cussed, with examples of performance achieve- ments under varying drilling conditions.

Jan 1, 1978

By Coulter K. W

The commercial evaluation of coking coal from bore core data will begin with a technical evaluation of the coal properties affecting coke quality. Methods currently used for prediction of coke.properties from coal analysis are illustrated but in each case accuracy of measurement and prediction should be clearly understood. It is suggested that coal be initially valued from coking properties (base value) and adjusted for chemical properties (merit value). Final evaluation of coal can only take place as coke in the blast furnace where the coke is assessed under high temperature operating conditions. The commercial value of a particular coking coal will depend on many additional factors other than the technical properties.

Jan 1, 1977

This address is set deliberately in the broadest possible terms. A review of the place of mining in Australian life today will serve to point up the changes that we can see in the life of people in the industry. Some of the influences on the future welfare of mining people bear also on the progress of this Institute, now approaching its 90th year. As mining becomes more and more dependent on higher technology and therefore, on the higher skills of the people in the industry, the role of The Institute, I suggest, becomes more and more significant.With investment per employee in mining generally continuing to rise, our ability to handle problems of manpower and human relations becomes a matter of greater importance.Questions that flow from these general thoughts form the substance of what I have to say.

Jan 1, 1982

Exploring for deep shallow dipping orebodies can be very expensive and very difficult. Surface exploration is often not an option and obtaining the best location for underground drilling can cause production delays if drilling is carried out from development headings. The Otter/Juan mine has been in production for approximately 34 years. All of the production is now sourced from more than 1000 metres below the surface from an area known as the Edwards Lode. The orebody is shallow dipping and open at depth. Exploration drilling has been performed from decline stockpiles and from hangingwall drill drives. Drilling from footwall positions (eg decline stockpiles) into shallow dipping orebodies can often produce intersections which are unusually thick thus leading to optimistic resource figures. The decision to develop a dedicated hangingwall drilling position can vastly improve the quality of the data used to generate an orebody model. In 1997 a new extension to the Edwards Lode was discovered and named the æFÆ surface. In 1999 a resource calculation was performed using data obtained from drilling that was carried out from decline stockpiles. In 2002 a dedicated drill drive was developed into the hangingwall of the æFÆ surface to obtain better data to verify the previous resource calculation. For this case study obtaining more representative data reduced the resource estimate by 66 per cent. This information was obtained early enough to allow for alteration to the mine plan and without loss of capital.

Jan 1, 2003