Search Documents

Blasting effectiveness must be gauged by total production costs. ANFO charges made up in polythene "sausages" are not as profitable as is indicated by the price of ANFO. All-slurry charges are warranted only where blastholes cannot be dewatered effectively, or where drilling costs are very high. An increase in blasthole diameter leads to coarser fragmentation. This effect is most pronounced in tough and massive or blocky strata, or in ground which consists of unfissured boulders in a softer matrix. When ANFO and some slurry-type charges of small diameter are used in plastic-acting ground, charges may fail to detonate through precompression by charges fired on an earlier delay. The optimum blasthole length is rarely less than four times the burden distance. For best results, blastholes should be inclined to the vertical and parallel to the face. Nominal burdens and spacings are often altered radically by the initiation sequence. For best fragmentation, all blastholes must have good effective faces, and should be effectively stagg- ered with an actual spacing:burden ratio in the approximate range 2.0-5.0.

Jan 1, 1975

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By Hinchliffe WD, Griffin A

The desorption of gold from activated carbon is promoted by adding organic solvents to aqueous cyanide solutions. At 65-80¦ the elution of gold is fast and is not affected by water quality. The Micron Procedure involves pretreatment of the loaded carbon with NaCN/NaOH followed by elution with methanol vapour and condensate. Carbon is packed into a column above the distillation pot and acts as a fractionating column. Recovery of the methanol condensate leaves a methanol free concentrated gold solution and carbon containing

Jan 1, 1984

A combination of highly structured, fissile stope hangingwalls and high ground stresses have caused difficult mining conditions in the Main Lode Deeps at Lancefield Gold Mine. Cyclic reviews of ground support and stoping techniques, coupled with geotechnical investigations, and the application of numerical modelling has led to the successful management of stoping operations.

Jan 1, 1995

By J E. Everett

A block model of the orebody is used to plan a mine. The first requirement is to identify ore to be extracted, discarding waste, so as to meet target grade, generally in multiple analytes. Commonly, cut-off values are set for each analyte, so as to distinguish ore from waste. It will be shown that, if more than one analyte is important, this procedure is wasteful of ore and a composite cut-off function is preferable.A second requirement is to sequence the ore extraction so that the variability in ore grade is controlled: failure to do so will result either in low-quality ore being marketed, or excessive re-handling being required to blend the ore to reduce the grade variability.A third requirement is that the extraction sequence should be such as to control the amount of equipment movement required, enhancing the equipment productivity.The overall objective, to optimise the Net Present Value (NPV) of the mined ore, is simply stated but complex in realisation, since so many factors, such as target grade, grade variability, equipment choice, equipment movement, and downstream blending all have alternatives which can be traded off against each other, and all of which contribute to the costs and benefits making up the total NPV.There exist commercial packages for ore selection and mine planning. However, they are often of a ‘black box’ nature, and users are sometimes not fully aware of the criteria being applied. In particular, the treatment of quality as a multidimensional vector may be problematic. The purpose of this paper is to discuss some of the issues involved and to suggest an alternative set of approaches, which should complement existing commercial treatments.The discussion will be illustrated specifically by reference to the mining of iron ore, but the issues are relevant to a wide variety of mining situations

Sep 5, 2011

WMC Resources Ltd has been involved the development and trialling of an automated load haul dump vehicle system since 1997. This paper describes the introduction of the system into the Olympic Dam Operation and its performance compared with existing manual loaders. In certain situations the autotram loader will outperform the manual operation, particularly on the longer distances. There were no personnel injuries associated with the operation of the system during the testing period.

Jan 1, 2005

The characteristics'of the Darling Range bauxite deposits are compared with tho"se of other large deposits in Australia and over seas The Bayer Process is them described with particular reference to the way.in which the process has been adapted to suit Darling Range bauxite. The.main characteristics considered are the physical aspects of the deposit.and its' effect on mining techniques, the grade of the ore and its effect on residue treatment, the nature of the alumina, iron and silica. content and their effect on process methods, equip- ment and raw material. Usage.

Jan 1, 1973

Saxonvale mine is a multi bench open pit coal mine developed to its Stage I capacity of 1.75 Mt/y of run of mine coal. Detailed engineering studies for the mine commenced in April 1980, approval to proceed with the development was received in July 1980 and first coal shipments were made in April 1982. The engineering and project management of the mine development was carried out by BHP Engineering. This paper outlines the design and site administration for the development and describes both the organisation structure and the control and administration procedures used by BHP Engineering to ensure that the project was Successful.

Jan 1, 1983

By Howlett P. F, Courtley S

A problem with secondary breaking at one of the mines of Pasminco Mining led to a study of new rock breaking technologies. Many of the techniques being developed had emerged from the thrust in the USA for continuous drill=break excavation. Such approaches to rock breaking highlighted the applicability of what would normally be classified as tunnelling techniques, to the secondary breaking sector - and possibly the reverse. As a direct result of the investigations for suitable technologies, Pasminco Mining supported the development of two improved rock breaking methods specifically targeting secondary breaking, one of which could be applied to continuous excavation.

Jan 1, 1993

By Fewings JH

When the mining and milling of 1100 Copper Orebody commenced, difficulties were experienced in producing a satisfactory grade of copper concentrate. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 Orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in an inherently flotable fine pyrite and silica fraction. The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to'the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1970

By S MacKinnon, J Kok

Potential areas for improvement in flotation performance were identified during JKTech model development surveys in October 2003. Subsequent implementation of the JKTech recommendations in consultation with flotation cell manufacturer Outokumpu have resulted in gold flotation recovery increases of more than four per cent over a two-year period. One of these recommendations was the installation of High Shear Stators in the Cleaner and Recleaner flotation cells. The High Shear Stator installation project was justified based on simulations completed using JKSimFloat. Bubble size measurements completed before and after installation of High Shear Stators showed a reduction in mean bubble size of approximately 50 per cent in the Cleaner cells. Both Cleaner and Recleaner banks showed a significant narrowing of the bubble size distributions following the installation. Plant gold recovery increase resulting from the installation of High Shear Stators was 1.1 per cent, with a 1.9 per cent increase in flotation gold recovery and 5.4 per cent increase in flotation sulfur recovery. Based on the 1.1 per cent recovery increase and total project cost of less than $200 000, the High Shear Stator Project NPV was $8 200 000 with a 0.25 year payback period.

Jan 1, 2006

By Wilson O. A, White R. W G

The Mount Morgan mine occupies a unique place in the mining history of Australia and although not as glamorous during the second phase of its existence, it made a significant contribution to the technical and financial history of the nation throughout its life. The stories of the intrigue surrounding its discovery and early operation, the enormous return received by its original investors in its first five years as a public company, its influence on the local, national and international scene to its final closure have been documented in many publications, the most recent and authoritative being by John Kerr (1982). Institute publications as far back as 1911 have documented details of the mining, metallurgical and engineering practices of the two companies which worked the 100 or so acres which were alleged to be `the richest single gold mine in the world'. Within the Institute records appear the names of Presidents, Institute Medal recipients and others connected with Mount Morgan who have played an important part in the Institute history.

Jan 1, 1993

By L Crew, S Jackson

A trial of an Adept Online Ore Sizer (OOS) was undertaken at the WMC Leinster Nickel Operation (LNO) in the first half of 2000. During this time the On Line Ore Sizer has been shown to be a robust and accurate instrument for measuring mill feed ore size. Data collected during the trial indicates significant variation in the F80 of the SAG mill feed. The effects of feed size on milling parameters such as mill weight, mill power draw and mill efficiency appears to be dependent on the ore blend treated. With some ore blends a weak positive correlation was found between ore size and mill weight and milling efficiency but with others no correlation is evident. It is believed that the OOS will become a vital piece of equipment in the future as LNO continues to optimises its milling circuit.

Jan 1, 2000

The middle-Devonian Dulladerry Volcanics is a complex of A-type, predominantly rhyolitic ignimbrites, lavas and breccias. They form a NNW trending belt some 90 km long and 10-20 km wide, east of Parkes, NSW. The volcanics are dominated by widespread ignimbrite units with minor basalts, sediments and rarer andesites. The volcanics were deposited in a sub-aerial, possibly continental rift setting and are similar in chemistry and age to the Eden - Comerong - Yalwal Volcanic Zone (EVZ) on the NSW south coast. The volcanics exhibit an unusual Atype chemistry (high Zr, Y, Nb, REE, Ga). This distinctive composition illustrates that the volcanics are not comagmatic with the adjacent Yeoval Granite Complex or Eugowra Granite, which show typical I-type fractionation trends. Epithermal gold veins occur in basalt and andesite in the Dulladerry Volcanics at Mt Aubrey (Hopf, 1992), near Baldry. Alteration also occurs in the Glen Isla and Red Hill areas, with epithermal sinter recognised at Glen Isla. Copper and minor gold mineralisation occurs at the contact of rhyolite and andesite at Reedy Creek, but is not of epithermal origin. The analogous EVZ also contains several epithermal gold fields and it is this style of mineralisation which provides the most prospective targets in the Dulladerry Volcanics. Although the Dulladerry Volcanics also contain high background levels of REE and metals such as Zn and Pb, the general lack of fractionation and water-undersaturated character of A-type magmas does not lend itself to the development of significant concentrations of these elements into a fluid phase and mineralisation. The prospectivity of A-type volcanics in general could not be regarded as high. However, an indicator of some fractionation in the Dulladerry Volcanics is provided by the fairly low abundance (average 230 ppm) and wide range (

Jan 1, 1995

This paper reviews the developments in understanding of the entrainment mechanism and its modelling in industrial flotation processes over the last 30 years. Both valuable and gangue minerals in the pulp zone of an industrial flotation machine can be transported through the froth zone to the concentrate launder in the water which must also be transferred from the pulp zone to maintain a stable froth zone in conventional flotation. A size dependent portion of each entrained mineral continues in normal circumstances to the concentrate launder. The size dependency arises because the larger particles are able to drain more successfully from the froth region. Gangue minerals are recovered by a number of mechanisms, entrainment being an important one in many cases. The entrainment mechanism is discussed on the basis of the pattern observed in recovery û size data for minerals. Its industrial implications are discussed and means of minimisation of the importance of the mechanism are also discussed. Various means proposed for mathematical modelling of the entrainment mechanism are also described. The effect of process variables on key parameters in these models is reviewed. Properties of both the pulp and froth zones are discussed where needed and means of taking additional measurements with devices developed over the last ten years are discussed as part of the collection of more detailed data on the flotation process in general and the entrainment mechanism in particular.

Jan 1, 2005

Microorganisms have been used throughout history for the benefit of mankind with some of the earliest applications being in the production of fermented foods and beverages. Reactions involving inorganic substances such as metals, sulphur and sulphide compounds were hardly ever used until the early 1900s when it was discovered that Thiobacillus ferrooxidans was capable of promoting the oxidation of metal sulphides in ores. Today, it is widely recognised that biotechnology has great potential in the minerals industries, particularly in such areas as the leaching of low-grade ores of metals such as copper, gold and uranium; removal of heavy metal ions from process streams and from liquid process wastes; and in the desulphurisation of high-sulphur fuels. Although widespread commercialisation of mineral biotechnology has not yet been achieved, it is estimated that by the Year 2000 mineral biotechnology will have a significant impact on the minerals and metal industry and will probably account for tens of billions of dollars worth of annual production world-wide. This paper examines the actual and possible future applications of biotechnology in the minerals, metal refining and fossil-fuel processing industries. Firstly, the important chemical (and biochemical) principles involved in bio-dissolution of metals from ores and solid wastes, and in bio-accumulation of metals from process and waste solutions are reviewed, including leaching practices - past, present and future. Microbial desulphurisation of coal, and microbially-enhanced oil recovery are also discussed. The practical aspects of genetics and genetic engineering, the types and characteristics of those microorganisms important to mineral biotechnology, and the current research trends are reviewed as well. KEYWORDS: Biotechnology, microbial leaching, bioaccumulation, biosorption, bioleaching, biohydrometallurgy.

Jan 1, 1993

This paper aims to provide some' new and original thoughts on tungsten carbide drill-bits and describe practices and performances, some of which are unique and most of which have not previously been described. Many theoretical and descriptive papers and articles on carbide bits have appeared during the last few years, and in the big majority conclusions such as these were made. These results are marked by premature failure of the bits, or The full or economic life of the bit is seldom reached due to the premature failure of the insert. Unfortunately those conclusions are seldom accompanied by the reasons for premature failure. In the few cases where reasons for failure have been advanced, very little, originality has been shown. The reasons usually given are that the failures are due to bad operators, bad workmanship, faulty steel or unsuitable machines, but it has been shown at Mount Isa that the chief reason for poor performnce is bad design.The first question asked will be, "What is wrong with the design of most bits?" and the answer'is, "The size of' the inserts". There may be many other small faults iiI different types of bit but Mount Isa experience indicates that the size of the insert is the most important factor influencing pit life. Under normal conditions it has been found, that there is a minimum size of insert that will give satisfactory performance, and this minimum is 5/16 in width and ? in. depth at the shoulder. A big majority of the bits at presentavailable in Australia do not satisfy these requirements.

Jan 1, 1953

By Marton A

The Readymix Group have a Quarry Improvement Program - 'Building in Quality (BIQ) which has many parallels to the ICI Explosives' total quality management - 'Quality Improvement Program' (QIP). Both companies have for some time recognised that the 'do it right first time' principle means less wasted effort and materials, that efficiency breeds profitability and so actively promote the quality culture. To install the principles and generate the culture requires considerable commitment and effort from the top down and invariably spreads to the suppliers and sub-contractors. Understanding the component processes involved with the quarry operation, analysis of those processes and gaining a breakdown of the cost of non conformance then allows the astute quarry operator to make the necessary changes to improve the process to realise profits. This paper outlines the steps in such a process and the profitable outcomes of the commitment to continuous improvement at the Nickol Bay Quarry.

Jan 1, 1994

By A Keddie

Standard microeconomic theory suggests that the behaviour of mineral extraction and processing firms with respect to their demand for water can be modelled and a market demand for water subsequently derived. Such a model, although an abstraction of the real world, should be able to predict the responsiveness of quantity of water demanded to change in price, and, change in demand to a range of factors including: expectations about reliability of supply, changed commodity prices for mineral production, and change in water technology and storage at mine site. This paper demonstrates that the price of water is particularly responsive to changes in demand and that although price increases would result in some additional supplies, physical constraints on supply suggest that the industry will be paying considerably higher prices for water in the future. It is recommended that the mining industry undertakes quantification of possible price increases to position itself to minimise the impact on their operating costs as well as to make responsible capital investment decisions to facilitate future expansion or commissioning of new mines. Substantial investment is required to commission a new mining venture with expected rates of return subject to risk and uncertainty due to fluctuations in world commodity markets as well as reliability of secure supplies of inputs. If a reliable supply of water was subject to uncertainty and water was a critical input for production, then the initial mine design would typically consider a range of production decisions contingent on levels of uncertainty with respect to water supply. These states or sets of water supply, will affect production decisions and future water demand. Modelling production decisions contingent on different states of nature, termed the state-contingent approach, provides a number of insights about producer behaviour under uncertainty. This paper investigates the assumptions underlying the derivation of the market demand for water by the mineral resource industry and identifies the drivers of demand and the responsiveness of the industry to change in price and supply, particularly in relation to capital investment in water-use technologies. The usefulness of these models to the mining industry is considered by reference to the increasing demand for water by the industry in Queensland, in a climate of water shortages.

Jan 1, 2006